SPL REPAIRS TO BLDG NO P 21 OFFRS MESS AND T 191 AT SUKNA MIL STN AND OTHER SANCTIONED WORKS AT SUKNA MIL STN OF AGE BR II UNDER GE SUKNA

Amount

M & L for sand filling under floors or in foundations including watering and consolidation as required complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in surface channel and drain complete all as specified and directed.

M & L for plain Cement Concrete Type B0 1:2:4 (using 12.5 mm graded stone aggregate) in top of chajja , roof kerbs or mud stops, rounded or chamfered on edges chajjas etc to prevent water seepage into brick walls, including necessory formwork and scafolding upto a height of 8 mtr complete all as specified and as directed.

M&L providing Reinforced cement concrete 1:2:4 Type B1 (using 20 mm graded stone aggregate) in lintels upto 1.5m clear span, window or door cills, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed.

M&L PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, filling in pressed steel door frames, wall of drains, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

M&L providing precast reinforced cement concrete 1:2:4 type (using 20 mm graded crushed stone aggregate) in lintel upto 1.5 m clear span and other similar bandand bed plate, manhole coverand drain cover complete all as specified and as directed.

M&L for Precast Reinforced cement concrete 1:2:4, type B1 (Using 20 mm graded stone aggregate) in landings, cover slabs (for Manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified and directed.

M&L for Reinforced Cement Concrete Type A-1 1:1.5.3 Nominal mix (using 20 mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, deck slabs and in shelves and the like complete all as specified and directed.

M&L Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

Supply only integral water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed.

M & L for brick work with sub class ‘B’, old size brick straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

Cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting n.exc. 10 cm in girth complete all as specified and directed.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade over 20 mm thick screed bed in CM (1:6) complete all as specified and directed.

Use and Waste of formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for rough finished flat formwork to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exc. 200 mm thick (horizontal or sloping) work as rough finished surfaces of concrete complete all as specified and directed.

S & F Second class hard wood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exceeding 6 Sq. cm and not exceeding 13 Sq. Cm complete all as specified and directed.

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. Species of timber :- Gamari (Gnelina arborea)

S & F 30 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. size of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkhats complete all as specified and directed. Species of timber :- Gamari (Gnelina arborea) / Chickerassy (Chukrasia Tabularis) / Siris (Albizzia procera) / Kalasiris (Albizzia Odoratissima)

S & F 35 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. size of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkhats complete all as specified and directed. Species of timber :- Gamari (Gnelina arborea) / Chickerassy (Chukrasia Tabularis) / Siris (Albizzia procera) / Kalasiris (Albizzia Odoratissima)

S&F 30 mm thick flush door shutters solid core construction, with MDF board exterior grade, commercial type on both side and covered on both side with decorative face veneer with liping/frame to match complete all as specified and directed.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

Taking down chowkats or frame n.exc 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frame but exc. 1.5 Sqm but not exc. 4.0 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

S & F 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F of 125 mm long Aluminium anodised barrel tower bolts, of extruded section complete all as specified and directed.

S & F of 150 mm long Aluminium anodised barrel tower bolts, of extruded section complete all as specified and directed.

S&F 300 mm long mild steel sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F 100 mm Aluminium butt hinge, medium weight, complete all as specified and directed.

S&F 100 mm butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F 300 mm, ordinary rat tail rod pattern springs and including roller and roller plate complete all as specified and directed.

S & F in repair MS Helical door spring 150 mm size including roller and roller plate fixed to wooden or steel frames with welding etc complete all as specified and directed.

S&F 150 mm Aluminium handles cast type, anodised and fixed complete all as specified and directed.

S & F 100 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 40 mm continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F 30 mm continuous (piano) hinges, brass, bright finish or electrogalvanised width of flaps (When open) 30 mmcomplete all as specified and directed.

Supply and fix mortice lock suitable for aluminium door of 100 mm size 4 lever brass body vertical type as per existing or sample complete all as specified and directed.

S&F Hasp and staple 100 mm safety type brass with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and as directed.

S&F in repair 150 mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S & F Ball catches with 8 mm dia., steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F in repairs Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width of aluminium (Die cast) body complete all as specified and directed by Engr-in-Charge.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed.

S&F in repairs decorative curtain rod of wooden finish chromium plated powder coated of 28 mm dia including 06 nos. curtain ring per running metre complete all as specified and directed.

S&F Decorative type wooden finish chromium plated powder coated double brackets support for holding curtain rods and corner to be fixed to ends of curtain rod fixing with screws complete all as specified and directed.

S & F of mild steel framed work such as grills, gratings etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe – 290 Gde E -- 165 complete all as specified and directed.

M&L for mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; handmade sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

S & F Joist, channel, angle, flat iron or tee sections, fixed independently, with connecting plates, etc. confirming to Fe 410 -W (Gde-250 quality A) complete all as specified and directed.

S&F rolled mild steel in plates, gusset plate (plain or chequered) channels square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410W (Gde-E-250) quality-A complete all as specified and directed.

S & F of roof trusses (framed), trussed, purlins, crane gantries, rails, fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections), including distance pieces, cleats etc. confirming to Fe – 410 – W(Gde E - 250) quality 'A' complete all as specified and directed.

S & F of structural steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 including fabrication complete all as specified and directed.

M&L welded steel wire fabric square mesh supplied and fixed complete to wood or steel members, weight not exc. 4 kg per square metre complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S & F Steel ventilator with top hung shutters including hinges, steel peg stay, complete all as specified and directed.

S & F of pressed steel frame of size 105 X 60 mm for doors with one or more rebates including filling of cement mortar or cement concrete necessary fixing lugs, hinges, lock strike plates and applying two coats of synthetic enamel paint over one coat of red oxide primer etc complete all as specified and directed.

S & F of pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc and applying two coats of synthetic enamel paint over one coat of red oxide primer etc complete all as specified and directed.

S&F 35mm thick flush shutters, solid core construction, with MDF board and plywood faces panels, commercial type on both side complete all as specified and directed

M&L powder coated Aluminium door, window, Cup board and ventilator shutter and frame any type (Sliding or openable ) with frame and other similar work, fabricated aluminium mesh etc. aluminium heavy section favricated incl all necessary roller wheels, cleats, handle, locking arrangement and arrangement to fix wire mesh with aluminium channel beading and stainless steel screw incl cost of rubber gasket ,beading roller wheel etc. ,complete all as specified and directed. Make:- M/s Halco Aluminium Extrusion / M/s Bhagwati Sai Metal Alloys / M/s Argent Industries Note: (a) The weight of rubber gasket beading, roller wheels, etc will not be measured with the weight of aluminium shutters as only aluminium items shall be measure. (b) Wire mesh shall be measured and paid separately. (c) Aluminium hinges shall be included in the unit rate

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws of any descriptions complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws of any descriptions complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F 4 mm thick E-board (designer pattern) celing confirming IS:733, 737 & IS:1285 of size 60x60 cm, fixed or laid / inserted to qnd including aluminium framework with screws in false ceiling (flat or sloping) of grid size 605 x 605 mm and including anodised aluminium snap grid frame work for false ceiling hanging from structural steel / scantling with 6 mm GI wire (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia., 40 mm long complete all as specified and directed.

M & L in repairs 18/19 mm thick prelaminated Particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber aluminium frame work with teak wood aluminium snap beading at the edges complete all as specified and directed.

S&F 18/19 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination fixed with necessary clips and screw to timber / aluminium frame work complete all as specified and directed.

S&F in repairs 18/19 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination fixed with necessary clips and screw to timber / aluminium frame work complete all as specified and directed.

M&L for white marble 30cmx20cmx20mm thick machine cut, bedded jointed with grey/ colored cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone as in floor including grinding, mirror polishing, moulding & over & including 20 mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as in sub base, floors, paths, plinth protection, alternate bays & construction joints to be given at every 3m interval and corners of buildings and filled with bituminous mastic or equivalent filler etc. finished even and smooth without using extra cement complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

M&L 75 mm thick, PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base finished even and rough complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 complete all as specified and directed.

All as per Sl item No. 74 above but area of each tile exc. 0.18 sqm but n. exc. 0.38 sqm.

All as per Sl item No. 74 above but in skirting etc. laid over and including backing of 10 mm thick in CM 1:3.

M&L 10 mm thick double charged premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 finish even and rough complete all as specified and directed.

M&L 10 mm thick double charged premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in skirting/dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick screed bed in CM 1:3 complete all as specified and directed.

M&L coloured glazed ceramic tiles 350x250x7 / 450 x 350 x 7 mm thick as in dado / skirting and vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick screed bed in CM 1:3 including roughening of surface complete all as specified and directed.

M&L machine cut kota stone flooring 20 mm (minimum) thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab and including rubbing and polishing and laid over 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L machine cut kota stone 10 mm (minimum) thick as in skirting, dado, riser of steps, plinth, etc, laid over and including 10 mm thick screed bed in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the stone and including rubbing / grinding and polishing complete all as specified and directed.

M&L 60 mm thick factory made machine pressed precast concrete interlocking coloured paver block of any shape and size confirming to IS 15658-2006, M-35 grade, chamfered edge cement concrete paver block 0f approved colour, design and pattern as in footpath, parks, lawns, drive ways or light traffic parking etc made by table vibratory method using PU mould laid over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of interlocking paver blocks on sand bed layer through vibratory compaction by using plate vibrator and filling the joints with fine sand and cutting paver block as required, finishing and sweeping extra sand complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces and finished the surface even and smooth without using extra cement complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick work or stone masonry or on one side of lathing surfaces and finished the surface even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M&L for rendering 5 mm thick rendering in CM 1:3 on ceiling finished even and smooth without using extra cement complete all as specified and directed. Note: The rate are inclusive of necessary scaffolding.

M&L for repair to broken/damaged RCC chajjas by making good with PCC 1:2:4 type B1 or rendering 15 mm thick in cement mortar 1:4 mixed with water proofing compound to top and sides and rendering 5 mm thick to soffits in cement mortar 1:3 including necessary form work, reinforcement duly welded if required including demolition of broken/loose PCC or taking down old plaster at any storey of building complete all as specified and as directed. (Note: Rate shall be included for necessary scaffolding and safety arrangement)

M & L for preparation of newly plastered or previously untreated surfaces of walls and applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

M&L for preparation of new plastered wall surfaces and including applying two coats of cement base paint over a coat of cement primer complete all as specified and directed.

M&L complete removal of existing treatment and preparation of old plastered wall surfaces and including applying two coats of cement base paint over a coat of cement primer complete all as specified and directed.

M&L preparation of new plastered wall surfaces and inlcuding applying two coats of weather coat exterior paint over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed. (Note: rate shall be included for necessary scaffolding and safety arrangement)

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of weather coat acrylic exterior emulsion paint over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

S & F Sheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed.

S & F 3 mm thick figured glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F 4.8mm thick glass including tinted/dark film n exc 0.5 sqm each pane complete fixed to aluminium frame work including rubber beading complete all as specified and directed.

S&F 4.8mm thick glass including tinted/dark film exc 0.5 sqm each pane complete fixed to aluminium frame work including rubber beading complete all as specified and directed.

S&F 4 mm thick frosted / pin headed glass in ventilator shutters complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

M&L preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F 15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor and including taking down of existing pipe complete all as specified and directed.

S&F 20 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor and including taking down of existing pipe complete all as specified and directed.

S&F 25 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc.) and fixed to wall / ceiling or laid in / on floor taking down of existing pipe complete all as specified and directed.

S&F in repairs sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 x 460mm bowl size 405 x 355 x 178 mm and including 32 mm waste pipe & coupling complete all as specified and directed.

S&F in repairs vitreous china European wash down water closet pan (pedestal pattern) white in colour with fixing bolts and flush pipe, connection to trap and to flushing cistern and all joints, including plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges complete all as specified and directed.

S&F in repairs vitreous china (white) flat back urinal of size 465 x 355 x 265mm (minimum) white with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws pointing around urinal back in cement complete all as specified and directed.

S&F in repair vitreous china wash hand basin, oval type of size 580x450mm white including waste coupling, waste pipe granite counter complete all as specified and directed.

S&F vitreous china wash hand basin white flat back of size not less than 550 x 400 mm with and including PVC waste pipe 32 mm bore, CP waste fitting and cutting for and pinning in ends of brackets etc, complete all as specified and directed.

S&F in repair PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F in repairs shower arm 15 mm size,450 mm long with bend of 90 degree with flange of PTMT any colour (minimum weight 40gms) complete all as specified and directed.

S&F in repairs 120 mm dia round shape multi flow casecade effect size swivel shower rose of ABS, chromium plated with gray face plate with rubit cleaning system for fixing with 15 mm pipe complete all as specified and directed. Make :- JAGUAR

S&F in repairs 15 mm bore bib taps, two way, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle and wall flange, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

M&L in repairs High dencity polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to wall,ceiling or floors etc.40 mm bore pipe complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of 1000 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed.

S&F in repairs stop cock / angle stop cock 15 mm bore, cast copper alloy, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or unions and fixed, fancy type, chromium plated long thread with flange complete all as specified and directed.

S&F in repairs 15 mm bore bib tap chromium plated fancy type, cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

S&F in repairs 15 mm bore bib tap long body chromium plated fancy type, cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

S&F in repairs pillar tap 15 mm bore,fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered “hot" or “cold” with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs stainless steel toilet paper holder with flat recessed type complete all as specified and as directed.

S&F in repairs, wall mixer brass chromium plated for mixing 'hot' and 'cold' water with connection to overhead shower with 115mm long, bend pipe and wall flanges, screwed down for iron pipe and fixed for 15mm bore pipe complete all as specified and directed.

S&F in repairs central hole basin mixer, brass, chromium plated, for mixing hot and cold water, with 450 mm Long Braided Hoses, screwed down for 15 mm bore pipe complete all as specified and directed. Make: Jaquar Cat Part No. 167 KNB or equivalent in MARC, Hindware

S&F in replacement 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in replacement 25 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repairs ball valves 20mm dia high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20 mm - 210 gms) complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts, of length 600 mm & suitable for hot water supply complete all as specified and directed.

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore of pipe complete all as specified and directed

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, incl bolts and nuts and securing ends of stays to wall or roof for 75 mm bore of pipe complete all as specified and directed

S & F of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls/ floors complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls/ floors complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) floor trap, plain with grating and including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) 110 mm bore bend, of any radius complete all as specified and directed.

S&F PVC (SWR) 75 mm bore bend, of any radius complete all as specified and directed.

S&F PVC (SWR) 110 mm bore bend, of any radius with access door complete all as specified and directed.

S&F PVC (SWR) 75 mm bore bend, of any radius with access door complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl of any radius complete all as specified and directed.

S&F 75 mm bore PVC (SWR) vent cowl of any radius complete all as specified and directed.

S&F in repairs health faucet 15 mm bore, ABS chromium plated with & including 1.25 mtr chromium plated flexible tube & wall hook including CP nipple and socket complete all as specified and directed.

S & F for in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repair acrylic assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets guard and railing 60cm long sixed fixed with and including plated brass screws (600mm long) complete all as specified and directed.

S&F in repair corner self of glass fixed with and including plated brass screws 8 inch long complete all as specified and directed.

S&F in repair stainless steel towel rings chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleat complete all as specified and directed.

S&F in reapirs Towel ring of PTMT fixed with and including Chromium plated brass screws and wooden / plastic cleats (minimum weight 90 gms) complete all as specified and directed.

S&F in repair towel rail 20 mm dia & 600 mm long of chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleat complete all as specified and directed.

S&F in repair soap dish with metal dish of chromium plated fixed with and including chromium plated screws and wooden / plastic cleat complete all as specified and directed. Make : Jaquar UF-0913 or equivalent in MARC, Hindware

S&F in repairs 75mm dia stainless steel gratings, doom type, chromium plated, with or without waste hole, fixed to floor trap complete all as specified and as directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

M&L for Dismantling of stone slabs and tiles of any description or thickness in floors, aprons, etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed.

Dismantling wall and ceiling boards, partitions of any description or in any position (fibre, pulp, insulation etc.) any thickness, or insulation boards/ slabs/ blankets of any thickness including cover fillets complete all as specified and directed.

Demolition and breaking up drain pipe of internal dia 100 mm (salt glazed ware, AC or reinforced concrete) set in cement mortar complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and directed by Engr-in-Charge.

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, modular plate and frame on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for one light / fan / exhaust fan / call bell point controlled by one 5 / 6 Amps switch, all necessary cutting chasing (as required) and making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. Note :- (i) Making good to match with the adjoining surface shall be included in the unit rate. (ii) Cutting chases shall be included in the unit rate.

All as per Sl. item No. 162.00 above but for point wiring modular plate one 5 / 6 Amps socket outlet point on independent board.

All as per Sl. item No. 162.00 above but for point wiring modular plate one 5 / 6 Amps socket outlet point on same board.

All as per item No. 162.00 here-in-before but one 3 pin socket outlet / 15 amps on the independent board with other switches, with cables 2.5 sqmm size complete all as specified and directed

M & L in replacement concealed sub main wiring with 2 runs of 4.00 sqmm main wire along with 1 run of 4.00 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

S&F switch piano modular type one way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch piano modular type one way, 15 /16 Amps independent, 240 volt complete all as specified and directed.

S&F socket outlet modular type 3 pin 5 / 6 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F socket outlet modular type 3 pin 15/16 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F in repair of modular metal flush box 3 module including taking down old unsv one complete all as specified and directed.

S&F in repair of modular metal flush box 6 module including taking down old unsv one complete all as specified and directed.

S&F in repair of modular metal flush box 8 module including taking down old unsv one complete all as specified and directed.

S&F in repair of modular white cover plate with frame 3 module complete all as specified and directed.

S&F in repair of modular white cover plate with frame 6 module complete all as specified and directed.

S&F in repair of modular white cover plate with frame 8 module complete all as specified and directed.

S&F MCB SP 6 to 32 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F MCB SPN 40 Amp , 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F in replacement MCB ,SPN DB, 08 ways double door,Metal door, IP-43 IK 09 in 100A rated bus bars,earth bar,neutral links complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces complete all as specified and as directed

S&F ceiling rose, surface bakelite 65 x 50 mm three terminal complete all as specified and directed.

S&F in repair electronic modular fan regulator, stepped type, white 120 W - 2 module complete all as specified and directed.

S&F Exhaust fan 250 mm sweep, non metallic plastic body, AC single phase, 230 V, 50Hz with & including self closing louvres, nuts, screws, bolts of specified sizes, electrical connection with twisted three core PVC insulated unsheathed flexible cord of size 0.75 sqmm copper conductor from ceiling rose to exhaust fan and writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole and making good the disturbed surface to match the existing surface complete all as specified and directed. Note: The quoted rate is including for taking down and depositing old fan to MES Store.

Supply and fix of energy saving 1200 mm sweep BLDC ceiling fan complete with all connected accessories including making provn for hanging with suitable clamps, hanging rod and nut, bolt etc as specified below: - Input Power :- 26 watts with full speed and reduced power consumption with reduced speed technology. Voltage :- 90-300 V AC, 50Hz, single Phase. RPM :- 340 to 375 rpm Blades :- Decorated Sweep :- 1200 mm. Air delivery :- Not less than 210 CFM Colour :- Glow white/Toast Brown/Gloss Black/or others as approved by Engr-in-Charge Speed/power contro :- Without Remote through existing regulator Star rating :- BEE 5 Star Rating Warranty: - As specified by the manufacturer, contractor shall produce original warranty and test certificate from the manufacturer.

S & F in repairs Light fittting 1 x 20 watt ,220 V AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete of suitable size complete all as specified and as directed.

S & F in repairs mirror type light fittting with high output diffuser 1 x 10 watt, 220 V AC 2 feet long, decorative box type with driver, holder including LED lamp connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete of suitable size complete all as specified and as directed.

Supply and fixing in replacement LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size Complete all as specified and as directed.

Supply and fixing of LED street light fittings of capacity 35 W made up of pressure die cast aluminium housing with high efficiency LEDs as lighting source and lens embedded PC cover having top opening seprate driver compartment with IP66 protection and impact resistance of IK07, lumen efficacy of minimum 120 Lm/W and SPD of 10 KV with a repair /replacement warranty of minimum 05 years fixing on pole complete all as specified and as directed.

Supply, laying testing and commissoning in replacement of cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) LT Cable with stranded aluminium conductor 1100 volts grade of size 10 sqmm 2 core including taking down old unsv complete all as specified and directed.

S&F VTPN DB, MCCB incomer, 4 ways double door,Metal door ,IP-43 IK 09 in 250A rated copper bus bars,earth bar,neutral links, no. of module DPX 250+12 complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces including taking down old unserviceable ones complete all as specified and as directed.

S&F MCCB 4P 125 Amps 415V ,50 Hz ,breaking capacity 25 KA complete all as specified and as directed.

S&F in replacement 1 x 15 watt LED post top lantern, IP-65, die cast aluminium housing, opal diffuser, electronic driver fixing arrangement etc complete all as specified and directed.

M&L for Earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level, connected to galvanized iron earth lead wire of 4 sqmm by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, P.C.C (1:3:6) type C-I with 50 mm thick Pre-cast R.C.C. (1:2:4) type B-I cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (light grade), wire mesh, aluminium lugs, complete in all respect, GI earth wire protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion including dismentaling old unsv ones complete all as specified and as directed by the Engineer-in-Charge.

MS ORIENT ENGINEERING WORKS (BID ID -3262703)

R N SAH N CO (BID ID -3262685)

M/S G S ASSOCIATES (BID ID -3262403)

PS ENTERPRISE (BID ID -3261516)

METTLE WORKS (BID ID -3262971)

MS ESSCON (BID ID -3260946)

M/S EASTERN ENGINEERING (BID ID -3262556)

A K ENTERPRISES (BID ID -3262963)