Repair_Renovation of IEs Change room of production section at Ordnance Factory, Ambarnath

Amount

Repair/Renovation of IE's Change room of production section at Ordnance Factory, Ambarnath

M&L Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.

Demolition of Concrete (Cement concrete (unreinforced)) in ground floors and pavings n exc 15 cm thickness (below or above ground level)

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L for Cement concrete in foundations,filling and mass concrete Type B2 1:2:4 (40 mm graded aggregate)

M&L for Screed bed or bedding layer of mortar 25 mm thick for laying floor finishes in CM 1:6

M&L Rendering 20mm thick on fair faces of brick work or concrete surfaces in CM 1:6

M&L coloured Glazed ceramic tiles in vertical surface 300 x 200 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L preparing new surfaces plastered or unplastered, chalk whiting on plastered surfaces of walls preparatory to distempering and applying two coat oil emulsion distemper on walls

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, AC sheet etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets

Dismantling Single layer Mangalore pattern or similar tiles in roofing

Dismantling of Battens for tiles, shingles etc, of any size including tilting fillets Exc 15 cm

S&F Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth for Brick walls.

M&L Filleting in any position and to any shape in cement mortar 1:3 including all mitres, stops, etc. section of fillet N exc. 25 sqcm

M&L Plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads but bullnosed, splayed, chamfered or rounded on one edge or face, 2nd class hardwood Exc 3 & n. exc 6 sq.cm

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples, in repairs

S&F Asbestos cement plain building boards, fixed to timber framework with screws (6mm thickness)

M&L for preparation of new or previously untreated surfaces two coat of synthetic enamel paint over a coat of primer paint on newly asbestos cement surfaces of any description not otherwise described over 10cm width or girth complete

Taking down Chowkhats or frames with shutters (without taking off shutters) from the frames not exc 1.5 sq. m each, removing to store.

S&F 1st class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered,put together with glue pinned at joints.

M&L for 2nd class hard wood in scantling, timber fixed with clean sawn wood.

S&F 1st class hardwood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged) thickness of shutter 40mm

M&L Preparation of new or previously untreated steel & iron surfaces of any description, over 10cm in width or girth, not otherwise described and applying Two coats of synthetic enamel ordinary tint , over a coat of primer red oxide zinc chrome

S&F MS Butt hinges medium weight cold rolled mild steel, size of hinges 100 mm,

S&F of Mild steel barrel tower bolts, stove enamelled black, with bright bolt 150mm

S&F Mild steel pressed handles, oval type, stove enamelled black 150mm

S&F MS sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate , sliding door bolt 300mm length

M&L Cutting holes in brick walls in mud mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required Exc. half brick but not exc.one brick

S&F MS hold fasts; and similar small articles conforming to Fe-290 Gde-E-165

M&L Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats 30mm thick 1st class hardwood 30mm thick

S&F Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, Thickness 4.0 mm thick

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6

Dismantling structural steel work including doors , gates but excluding framed truss etc.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, Fe- 290 (Gde E- 165)

Dismantling in fillets, rails, posts, rafters,purlins, etc. under 40 sq. cm in section, unframed work

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings

S&F Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 if fixed with L-type or J-type or cranked hook bolts in lieu of screws. 0.63 mm thick

S&F IInd Class hard wood clean sawn, battens at 30 cm centre to centre, cross sectional area exc. 5 sqcm and n.exc. 15 sqcm

M&L for Roof tiles, Mangalore pattern, interlocking at side joints, laid dry

Felling of tree exc. 30 cm girth including cutting of trunk, and branches and stacking of serviceable material and disposal of unserviceable material to a distance n exc. 50 m and clearing site, Girth of tree - Exc. 30cm and n exc. 100cm

M&L Painting on Tiles or slate battens, any size and spacing, prepared and treated all over (measured overall on one side only, spaces not deducted) with creosote.

Taking down and refixing in same opening door shutters of any description exc 1 sq. m and n exc 2 sq. m each

Removing building materials etc. (other than spoil payable under items 03028 to 03031 in Section-3—Earthwork) to a distance of 100m or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination

Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed

Old dismantled MS angles, tee, Alu/GI plain/corrugated sheet, valley gutter & Other sections (Credit Item)

Old AC corrugated sheets

GOLDEN CONSTRUCTION

KUGANCONSTRUCTIONS