REPAIR/MAINT OF JOINERY, FLOORING, PLASTERING and MISC WORKS IN CERTAIN JCOs/OR ACCN UNDER AOR OF GE SGNR

Amount

Taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 sqm each as doors, windows & ventilators etc. and complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm each with shutters (W/out taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each and complete all as specified and directed by Engineer-in-Charge.

Taking down wooden shutters only of any description area exceeding 1.0 sqm and not exceeding 2.0 sqm each and refixing in same opening after necessary easing, adjustments, minor repairs, oiling, adjustment with cutting or fixing plain fillets/planks made from second class hard wood etc to remove gap between floor and shutter complete all as specified and as directed by Engineer-in- charge.

S&F second class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed by Engineer-in-Charge. (Note : The back of chowkhats shall be treated with two coats of tar coat & cost for same shall be included in quoted rate)

S&F factory made Pressed steel frames of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, (thickness of sheet shall be 1.25mm) and making good the wall with plaster in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

S&F factory made for pressed steel frames of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, locks strike plate etc, (thickness of sheet shall be 1.25mm) and making good the wall with plaster in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L PCC 1:3:6 type C-1 using 20 mm graded stone aggregate for filling in back of pressed steel door frame/chowkhat and fixing of bed block of hold fast etc complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class HW factory made Plain, framed, pannelled shutters 35 mm thick (two panels), with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I) Kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge.

S&F factory made 2nd class hardwood glazed skeleton shutters 35 mm thick open rebated and prepared to receive guage etc but divided into squares, with plain chamfered or rounded, metered and riveted sash bars any numbers also complete all as specified and directed by Engineer-in-Charge.

M&L in replacement for Plain fillets or beading of sectional area Exc 3 & n. exc 6 sq.cm of 2nd class hard wood square, rectangular or triangular in section , clean sawn, se-cured with nails or brads for securing wiremesh or similar works put together with glue pinned at joints in complete all as specified and directed by Engineer-in-Charge.

S&F factory made Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete all as specified and directed by Engineer-in-Charge.

S&F factory made frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete all as specified and directed by Engineer-in-Charge.

Dismentling of boarding any description fixed in any position with nails/ screws complete all as specified and directed by Engineer-in-Charge.

Supply & fixing 18mm thick Plywood, grade BWR, type BB, fixed with screws to frame work along with one side laminate and other side plain white 0.9mm thick type-I, colour pattern as approved including PVC lipping, PVC sheet is heat bent as lipping on the edges of doors complete all as specified and as directed by Engineer-in-charge.

S&F 25 mm size magnetic catches with Plastic body and striking plate including letting in and fixed complete all as specified and directed by Engineer-in-Charge.

S&F continuous (piano) hinges 20mm & 12 MM width of flap, mild steel bright finish or electrogalvanised of complete all as specified fixed with CP steel screws complete all as specified and directed by Engineer-in-Charge.

S&F butt hinges of size 100 mm medium weight, stainless steel ISI marked complete all as specified and directed by Engineer-in-Charge.

S&F aluminium handle, 150mm size, cast type, anodized (ISI marked) complete all as specified and directed by Engineer-in-Charge. (D type Handle and back side staple)

S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-Charge.

S & F aluminium anodised, barrel tower bolts of extruded section and fixed, length of bolt 150mm complete all as specified and directed by Engineer-in-Charge.

S&F 250 mm long mild steel sliding door bolts, clip type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed by Engineer-in-Charge.

S&F mild steel helical door spring 300mm long ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

S&F in 150mm length floor door stopper of aluminium alloy body and tongue,anodised with hard drawan steel spring fixed in floor complete all as specified and directed by Engineer-in-Charge.

S & F hasp and staple, safety type of aluminium anodised100mm size fixed with screw complete all as specified and directed by Engineer - in - Charge.

M&L for Cutting holes in brick walls built in cement mortar including making good dismantled portion in CM (1:3) or cement concrete (1:2:4) type B-1 exc half brick but n.exc one brick complete all as specified and directed by Engineer-in-Charge.

S&F Aluminium frame for doors, window, ventilators with one or more rebates including joining cleat for fixing etc complete with powder coating on Aluminium minium thickness of powder coating 50 micron as per the specification the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawal plug and screw or with fixing clip or with expansion hold plate fasteners . Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required all complete as per the direction of Engineer-in-charge

S&F Aluminium window (glazed and gauzed both),side hung type without sash bars, aluminum section weighing 0.55 Kg/m including necessary joining cleats, glazing, clips, rubber packing, anodised aluminium snap beading screws,aluminium fitting such as peg stays 150mm long (01 for each shutter), hinges type B-21 100mm long (02 Nos) suitable handle (01 for each shutter) , Tower bolt (100mm) (01 for each shutter) with powder coating of any colour (thickness of powder coating not less than 50micron) etc complete all as specified and directed by Engineer-in-Charge. Note: The Glass and wiremesh will be measured and paid seperately.

Supply & fixing anodised aluminium ventilator fixed type with frame and shutter, made out of aluminium section weighing not less than 0.55 Kg/mtr, powder coated (minimum thickness of powder coating not less than 50 micron) including necessary joining cleats, fitting, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws etc complete all as specified and as directed by Engineer-in-Charge. Note :- Glass shall be measured and paid separately under appropriate item of BOQ.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and avarage width of aparture 1.40mm and fixed etc.,complete all as specified and directed by Engineer-in-Charge.

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified.including taking down ms frame and refing ms frame with new wire mesh with tinned tack/by welding in steel window/ventilator /door and making good the disturbed portion during execution complete all as specified and directed by Engineer-in-Charge.

M & L sheet glass ordinary quality 5 mm thick and glazing with oil putty / aluminium flats in square n exc 0.50 Sqm in each panes fixed to steel, metal or wooden/ aluminium window frames including hacking out old broken glass complete all as specified and directed by Engineer-in-Charge..

M & L in repair sheet glass ordinary quality 5 mm thick and glazing with oil putty or fixing using aluminium beadings in square n exc 0.50 Sqm in each panes fixed to steel, metal or wooden/ aluminium window frames complete all as specified and directed by Engineer-in-Charge.

S & F 3 mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beading in square n.exc. 0.5 sqm in each pane complete all as specified and directed by Engineer-in-Charge.

S&F Framed work such as grills, gratings coolar stand, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (for steel surfaces) including preparation of surface complete all as specified and directed by Engineer-in-Charge..

M&L preparing new wood or wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted surfaces including as knotting, stopping, Burning off or removing, scraping etc,and then applying one coat of synthetic enamel paint (ordinary tint) on steel surfaces over 10cm width or girth complete all as specified and directed by Engineer - in - Charge.

M & L for applying one coat of synthetic enamel paint on wood and wood based surfaces of any description, over 10cm width or girth, not other wise described including preparation of old painted surfaces complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), terrazo dado/wall tiling and skirting. etc on brick or stone walls etc including racking out joints hacking for key and scrubbing and removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Roughning of surfaces of old concrete floor by picking,sweeping clean and washing down with water to remove dust etc complete all as specified and directed by Engineer-in-Charge.

M&L Non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 but not exceeding 0.38 sqm, in floors laid over & including 15 mm thick Screed bed or bedding layer in CM (1:4) etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engineer-in-Charge..Note : Using only coarse sand in screed bed

M&L Non Skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 but not exceeding 0.38 sqm, cut to reqd size and shape as in skirtings laid over & including 10 mm thick rendering in cement mortar 1:4 etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match. complete all as specified and directed by Engineer-in-Charge. Note :- Rendering will be done in course sand (Toka sand) only

M&L Non skid ceramic cololured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 Sqm but n.exc 0.18 Sqm laid over & including 15 mm thick Screed bed or bedding layer in CM (1:4) etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engineer-in-Charge..Note : Using only course sand in screed bed..

M&L Non skid ceramic cololured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 Sqm but n.exc 0.18 Sqm. in skirtings laid over & including 10 mm thick rendering in cement mortar 1:4 etc complete all as specified and directed by Engineer-in-Charge..Note :- Rendering will be done in course sand (Toka sand) only

S&F glazed ceramic coloured tiles 7mm thick 450 x 350mm/350x250x7 mm thick in size in verticle surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade laid over & including 10 mm thick rendering in cement mortar 1:4 as in vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match.Note :- Rendering will be done in course sand (Toka sand) onlyetc complete all as specified and directed by Engineer-in-Charge.

Dismantling stone slabs of any description or thickness in floors, apron etc laid bedded and pointed in any mortar complete all as specified and directed by Engineer-in-Charge.

M&L marble work (Udaipur green slabs) 18 to 20mm thick (table rubbed and polished) as in cooking platforms and like in cement mortar (1:4) in pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade and roundening to the edge of stone slabs on edges in single pice of stair case steps in horizental and vertical portion over 15mm thick screed bed etc. complete all as specified and directed by Engineer-in-Charge.

Demolition of RCC of any descrition such as Kitchen chimney, chajja, shelves, OHT Tanks. etc and in any position not other wise specially provided for complete all as specified and directed by Engineer in Charge (reinforcement cut as required to facilitate demolition) complete all as specified and directed by Engineer-in-charge

M&L for reinforced cement concrete type B1 1:2:4 (20 mm graded aggregate) as in slab supported on walls, beam and column in floors, roofs,landings,balconies,deck slab and in shelves and etc and setting in mortar complete with joints to match complete all as specified and directed by Engineer-in-Charge. (Note : RCC Slab casting for tank staging also)

Use and waste of form work through finished surface of soffits of suspended slab as roof slabs, floor, lamnding and similar work not exceeding 200 mm thick complete all as specified and directed by Engineer-in-Charge.

M & L in replacement mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in cement mortar 1:4 on fair face of brick work of walls, mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. .Note : - Supply only water proofing compound shall be measured and paid for separately.

Supply only integral water proofing compound, ISI Marked complete all as specified and directed by Engineer-in-Charge.

M&L for prepration of New external plastered wall surface complete all as specified complete all as specified and applyingthe following :- (a) Applying 1.5mm wall care putty in one coat on wall surface and smoothening the surface with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified and directed by Engineer-in-Charge. (b) two coats of exterior acylic emulsion by using Roller over and incl a coat of acrylic emulsion external primer complete all as specified and directed by Engineer-in-Charge.

M&L Complete removal existing treatment and prepartation of existing surfaces and applying two coats of premium acrylic smooth advance dust proof emulsion paint with silicon additives on external surfaces of wall incl primer over 1.5mm thick wall care putty on plaster surfaces of wall complete all as specified and directed by Engineer-in-charge.

Taking up or down GI tubing 15 mm bore pipe with fittings including cleaning for re-fixing complete all as specified and directed by Engineer-in-Charge.

Ditto- but refixing 15 mm dia ,old steel tubing and connections in new or old possition (wall,ceiling and floors etc) complete all as specified and directed by Engineer-in-Charge.

S&F GI tubing 15 mm bore medium grade galvanise with all fitting and fixed to walls & ceilings or laid in floors, complete all as specified and directed by Engineer-in-Charge.

Taking up or down GI tubing 20 mm bore pipe with fittings including cleaning for re-fixing complete all as specified and directed by Engineer-in-Charge.

Ditto- but refixing 20 mm dia ,old steel tubing and connections in new or old possition (wall,ceiling and floors etc) complete all as specified and directed by Engineer-in-Charge.

S&F GI tubing 20 mm bore medium grade galvanise with all fitting and fixed to walls & ceilings or laid in floors, complete all as specified and directed by Engineer-in-Charge.

Dismantling PVC water tanks and capacity exceedin 250 litres & not exceeding 500 litres etc., complete all as specified and directed by Engineer-in-Charge.

S & F rotational moulded polythylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part -I (500 Ltrs) capacity. complete all as specified and directed by Engineer-in-Charge. Note : PVC Tank shall be ISI marked and having two layer.

S&F 20 mm ball valve high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball screwed for iron pipe, complete all as specified and directed by Engineer-in-Charge

S&F in repairs gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20 mm bore, complete all as specified and directed by Engineer-in-Charge

Disconnecting existing tanks of capacity exceedin 250 litres & not exceeding 500 litres etc, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. complete all as specified and directed by Engineer in Charge

Disconnecting existing tanks of capacity exceedin 500 litres & not exceeding 1000 litres etc, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. complete all as specified and directed by Engineer in Charge

Demolition and breaking up or taking down PVC/AC/CI/SSW 100mm bore pipe drain pipes, set in cement mortar including PCC haunching and bedding, complete all as specified and directed by Engineer-in-Charge

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed by Engineer-in-Charge

S&F 110mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed by Engineer-in-Charge

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge

S & F Stack clamps out of 50mm by 5 mm flat iron and 16mm dia round iron stays for 100mm bore of pipe, including bolts and nuts and securing ends of stays to wall or roof etc complete all as specified and directed by Engineer - in - Charge.

Material and labour for water proofing treatment to sunken slab, walls, etc, and shall be carried out as specified below and as directed:- (a) Demolition of Cement concrete/brick bats filled on sunken slab upto mother slab including removing and Clean the sunken portion of toilet / Baths/ WCs/ Kitchen thoroughly to remove laitance, dirt, dust etc. (b) Brushing cement slurry with 1.2 kg of cement per square metre duly blended with & including water proofing compound. (c) 15 mm thick (Average thickness) plaster in cement mortar (1:4) mixed with water proofing compound on sunken surface including walls. The corner of sunken portion shall be rounded in concave shape and adequate slope shall be made during plastering to accommodate sump pipe and curing the sunken portion with water minimum for 48 Hrs by ponding. (d) Applying self adhesive type APP based polymeric membrane minimum weighing not less than 3.6 kg/ Sqm and minimum 3 mm thick reinforced with polyester non-woven fabric (weight not less than 150 gm/Sqm) (e) M&L for PCC 1:7:12 type F2 using brick course agreegates for filling of sunken portion after conceling all menbrane upto FFL and sealing all joints to the entire satisfaction of Engineer-in-Charge. (Note:- Floor area shall be considered for measurement & payment purpose)

S&F in repairs 40 mm GI pipe medium grade, made to shape as in spout pipe in sunken/ verandah/ Balcony complete all as specified and directed by Engineer-in-Charge

S & F in repairs vitreous China squatting pan of Orrissa pattern of approved make of size 580 mm X 440mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe incl lime concrete bedding and connection to antisyphonage pipe etc including making good to floor complete all as specified and directed by Engineer-in-Charge

S&F in repairs white Vitreous china wash down water closet (pedestal pattern) with fixing bolt, Plastic water closet seat cover, white, closed pattern with flat bottom, and cover with aluminised hinging device, brass chromium plated Jet shower with one meter long flexible pipe including all connection complete all as specified and directed by Engineer-in-Charge

S&F in repair brass chromium plated jet spray fitting with chrome plated 1.5 mtr long extendable, flexible tube, fixed to EWC complete all as specified and directed by Engineer-in-Charge

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed by Engineer-in-Charge

S & F in repair PVC low level cistern of 10 ltrs capacity with top push buttion inclusive of brackets and PVC bend long type and connectin to flush pipe of any size and pattern with inlet ball valve float and handle complete all as specified and directed by Engineer-in-Charge

Shotcreting average thickness 25mm in RCC columns, beams and slab etc. (with mix minimum cement content of 350 Kg per Cum, M-25). Concrete having the specified minimum characteristic compressive strength (with ordinary portland cement, coarse sand and graded stone aggregates of 6mm to 10 mm size in proportion as per design citeria) incl the cost of centering and shuttring at edges and corner etc as directed by Engr-in-Charge incl chipping of unsound/week concrete material 25mm average thickness from slabs, beams/ columns etc with mannual chisel or standard power driven percussion type all of approved makes incl tapering of all edges, making square shoulder of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes and throughly washing with water and allowing it to dry incl removel of rust by applying approved rust remover chemical and the coating with Dr Fixit Epoxy zinc primer @ 6 Sqm per Litre at DFT of 100 micron as per manufacturer's instruction and specification, including removing rubbish material from building and thrown in low lying empty area at any distance from the site as complete all as specified and directed by Engineer in Charge. (Note : Complete treatment to be executed by approved applicator.)

Supply and fixing in repairs hard drawn steel wire fabric not exc 4kg/sqm cut to lengths, wire mesh to be fixed and firmly anchored to the concrete surface by means of 'L' shaped mild steel shear key welded with existing reinforcement including cost of material, labour, tools, and plants incl welding/L-clip/typing with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed by Engineer in Charge.

S&F in repairs for mild steel ISMB, Joist, channel, angle or teee sections, fixed adjacent to ceiling and embedding in floor and brickwork including cutting welding, without connection plates, etc. (cut to ordinary lengths i.e. Within 20mm of the length indicated) FE 410 W(GdeE-250) quality 'A' complete all as specified and directed by Engineer-in-Charge.

M&L 5mm thick, rendering in cement mortar 1:3 to ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for applying two coat of white wash on newly plastered surface of ceiling over a coat of wall putty to make the surface even and smooth etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs 15 mm dia bore cast copper alloy fancy type chromium plated long body bib taps cast copper alloy with on/off handle, screwed down, screwed for iron pipe, or for brass ferrule complete all as specified and directed by Engineer-in-Charge

S & F in repairss 15 mm dia bore cast copper alloy fancy type chromium plated concealed stop valves of cast copper alloy with long shank & cup etc. complete all as specified and directed by Engineer-in-Charge

S & F in repairs 15 mm bore cast copper alloy chromium plated Angular stop valve of cast copper alloy screwed down high pressure with on/off handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer-in-Charge

S&F in repairs long body15mm bore fancy type pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes complete all as specified and directed by Engineer-in-Charge

S & F PVC connection 15 mm size with PTMT nuts of length 600 mm of approved quality complete all as specified and directed by Engineer-in-Charge

S&F in repairs PTMT grating 125mm dia with waste hole (Minimium weight 40 grams) complete all as specified and directed by Engineer-in-Charge

S&F in repairs PTMT grating 100mm dia without hole (Minimium weight 25 grams) complete all as specified and directed by Engineer-in-Charge

S&F in repairs stainless steel plate racks of size 750mm x 600mm x 250mm and thickness of SS strip of 1mm fixed on wall etc complete all as specified and directed by Engineer-in-Charge

S&F in repair sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe including 40mm dia CPBrass waste fitting amd waste pipe overall size of SS sink 495mm x 420mm bowl size 410mm x 330mm x 160mm, etc complete all as specified and directed by Engineer-in-Charge

S&F in repair wash hand basin of size 550 x 400 mm vitrous China white flat back including brackets, waste coupling & PVC waste pipe of 32 mm dia etc. complete all as specified and directed by Engineer-in-Charge

S&F in repair corner wash hand basin of size 450 x 390 mm vitrous China white flat back including brackets, waste coupling & PVC waste pipe of 32 mm dia etc. complete all as specified and directed by Engineer-in-Charge

S&F in repair Brass CP mixer 15mm bore for mixing hot & cold water screwed down for iron pipe for Wash Hand Basin complete all as specified and directed by Engineer-in-charge

S&F in repair brass chromium plated shower rose 125 mm of size with arm and with or without swivel joints to steel pipe or union complete all as specified and directed by Engineer-in-Charge

M&L in replacement for 25mm dia fancy type PVC coated MS Pipe coloured curtain rod with brackets and knobs at both ends as per site requirement including taking down old existing curtain rods any description with accessories complete all as specified and directed by Engineer-in-Charge. Note : The cost of brackets and knobs is deemed to be included in the quoted rate. Nothing extra shall be paid on this account.

Dismantling of brick work or stone/boulder masonry built in cement mortar including all quoins, arches , pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge

M&L brick work with sub class B bricks straight or curved on plan exceeding 6 mtr mean radius in cm 1:6 etc.complete all as specified and directed by Engineer - in - Charge.

Dismantling of brick tiles or terracing tiles single layer on roof including also taking down existing APP membrane & disposal of retrieved material upto a distance n.exc 100m complete all as specified and directed by Engineer-in-Charge

Demolition of mud in roof, any thickness including plastering and leaping (where full thickness removed or only a part there of disposal off rubbish upto a distance n.exc 100m, complete all as specified and directed by Engineer-in-Charge

M&L for cement concerete 1:2:4 (20 mm graded aggrigate) as in filling and mass concerete as in roof padding etc complete all as specified and dirceted by Engineer-In-Charge.

M & L for cleaning of old Roof wall/ concrete surfaces & applied a TWO coat of cold bituminous primer over cleaned surface @ 0.40 Kg/Sqm followed by APP modified five layer ploymeric membrane 3mm thick, minimum wt 3.60 kg/Sqm reinforced with polyester non-woven fabric (weighing not less than 150gms/Sqm ) manufactured by M/S STP Ltd/IWL India Ltd or its equivalent, laid as per the manufactures instruction with side over lap of 75mm & end over lap of 100mm & tucked into the chases on vertical surfaces if required complete all as specified and directed by Engineer-in-Charge

M & L 40mm thick brick tiles bedded in 15 mm thick cement mortar (1:6) and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and directed by engineer in charge

M & L 40mm thick brick tiles retrived from dismantling and refixing old brick tiles bedded in 15 mm thick cement mortar (1:6) and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and directed by Engineer-in-Charge

M&L Cement concrete tiles 25cm x 25xcm x 20 to 22 mm thick,with gray cement and no pigment machine pressed; set, jointed and pointed in neat cement slurry laid over and including cement 15 mm thick scereed in CM (1:6) with and including liquid water proofing compund as per manufactures,s specifications, as in toof and floor tiles complete all as specified and directed by Engineer-in-Charge

M&L PCC 1:2:4, type B1 using 20 mm graded stone aggregate as in roof kerbs / benching / coved fillets etc rounded or chamfered on edges, complete all as specified and directed by Engineer-in-Charge

Note :(i) Amount of credit for retrieved materials is mentioned in Sch 'A' Section-II of tender documents in pdf form which will be deducted while acceptance of tender offline.

PAREEK AND COMPANY (BID ID -3067180)

Dashmesh Construction Company (BID ID -3077556)

M J BUILDERS (BID ID -3077179)