PROVN OF TILES IN BLDG IN LIEU OF WOODEN FLOOR, JOINERY AND SANITARY FITTING IN BLDG NO. S-10 AND S-11 (16 DUS OF OR FAFA ACCM) OF ARC AND ADDN/ALTERATION OF ROOF OF MD ACCN AT 58 GTC UNDER GE SHILLONG

Amount

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

Dismantling of timber scantling 40 Sqcm and over in section, in any position as in unframed or framed work complete all as specified and directed.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for Hardcore of gauge n exc. 63 mm size broken stone or boulder, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for PCC 1:4:8 type D2 ( Using 40mm graded agg) as in foundation and mass concrete complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B-0 (12.5 mm graded aggregate) as in levelling coarse of tile flooring etc complete all as specified and as directed.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.11 Sqm but not exc. 0.18 sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including 15 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes finished fair and even complete all as specified and directed.of tile complete all as specified and directed.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.11 Sqm but not exc. 0.18 sqm, on vertical surfaces such as skirting, dado, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tiles including 10mm thick rendring in CM (1:4) on fair faces of brick or concrete surfaces finished fair and even on vertical surfaces of wall complete all as specified and directed.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.11 Sqm but not exc. 0.18 sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including 15 mm thick screed bed or bedding layer in cement mortar 1:6 and including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and as directed.

M&L for Non-skid ceramic colour tiles 7 to 8 mm thick , (square/rectangular), area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:4 complete all as specified and as directed.

M & L for glazed ceramic coloured tiles 300 mm X 450 mm X 7 mm thick as on vertical surface of wall such as skirting, dado, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tiles including 10mm thick rendring in CM (1:4) on fair faces of brick or concrete surfaces finished fair and even on vertical surfaces of wall including roughening surfaces of old plastered wall by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and as directed.

M&L for rendering 10mm thick plaster in cm (1:6) on fair faces of brick or concrete surfaces and finishing even & smooth without using extra cement including taking down cement plaster including racking out joints, hacking for key scrubbing down with water etc including removal of rubbish material from site complete all as specified and as directed.

M & L for preparation of new plastered/concrete surfaces of walls, providing one or more coats of Birla white wall care putty to achieve smooth surface and applying two coats of Oil Bound Distemper of approved shade/tint over a coat of priming paint complete all as specified and as directed.

Taking down chowkhats or frame with shutter without taking off shutter from the frame exc 1.50 sqm but not exc 4 sqm each & removing from site complete all as specified and directed.

Taking down chowkhats or frame with shutter without taking off shutter from the frame not exc 1.50 sqm & removing from site complete all as specified and directed.

Taking down shutters of any description exc 1 sq. m n exc each Sqm each and refixing in the same opening complete all as specified and directed

M&L for MS flat iron such as small articles for hold fast and similar work all as specified and as directed by Engineer-In-Charge.

M&L PCC 1:2:4 type B1 using 20mm graded crushed stone Aggregate) as in for fixing hold fast, rafter portions,finishing gable wall junctions/top portions, paths etc. complete all as specified and directed.

M&L for 2nd class HW plain solid straight chowkhats/frame wrought framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

S&F 35mm thick Flush door shutters, solid core construction with block board core and ply wood face pannels commercial veneered on both faces complete all as specified and directed.

M&L for 35mm thick 2nd class HW plain framed panelled shutters (any number of panels), with panel of timber flats on both sides or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats complete all as specified and directed..

M&L for 35mm thick 2nd class HW Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares (without sash bars ), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F powder coated (min powder coating 50 micron) anodised aluminium frame for doors, windows , ventilators plain or sliding type with one or more rebates including joining cleat for fixing etc complete all as specified and as directed

S&F powder coated (powder coating min 50 micron) anodised window and ventilator shutters side hung/sliding type without sash , aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , anodised aluminium snap beading screws ,anodised aluminium fittings such as peg stays 150 mm long(1 no) hinges type B-21 100 mm long (2 no) suitable handle (1 no ) complete all as specified and directed.

S&F 4.80 mm thick frosted sheet glass and glazing/ fixed to aluminium frame n exc 0.50 sqm all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

S&F framed work such as grills, gratings, wind ties etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165all as specified and as directed

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new/old untreated steel surface exc 10cm width or girth and applying of two coats of synthetic enamel paint over a coat of red oxide all as specified and directed.

S&F 100mm size MS butt hinges cold rolled medium weight, ISI marked complete all as specified and directed.

S&F 200mm size MS barrel tower bolt stone enamelled black with bright bolt ISI marked complete all as specified and directed.

S&F 150mm size MS pressed handle oval type stove enameled block complete all as specified and directed.

S&F 250mm long MS sliding door bolt, plate type, stove enameled black with bright bolt not less than 12mm dia with and including a min of size bolt & nuts four on bolt & two on staple,ISI marked, complete all as specified and directed.

Supply and fixing 150 mm size Aluminium anodised barrel tower bolt complete all as specified and directed.

Supply and fixing 150 mm size aluminium handle complete all as specified and directed.

S & F 140mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S & F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples comlete all as specified and as directed.

Taking down GI tubing 15mm dia and connection including removable to store complete all as specified and directed.

S&F 15 mm bore galvanised steel water tubing, medium grade including necessary fittings such as GI bends, tee, union etc fixed on wall / floor complete and connecting to water supply pipe line, concealed in wall complete all as specified and directed.

M&L for Cutting chases, of girth not exceeding 10 cm for concealed water tubing or concealed conduit wiring, etc. in stone / brick masonry wall built in cement mortar and making good, disturbed surface in Cement mortar 1:3 complete all as specified and directed.

S&F in repair 15mm bore stop cock cast copper alloy, fancy type, chromium plated, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed complete all as specified and directed.

S & F in repair 15 mm bore CP fancy type bib tap cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repair 15 mm bore CP fancy type 2 in 1 bib tap long body cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repair for PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F as in repairs.Vitreous China wash down water down water closet pan (pedestal pattern- P trap), white (excluding fixing bolts, flushing cistern and flush pipe) including Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S & F in repair PVC, valve less, Syphonic action type, flushing cistern of capacity 10 litres, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints fixed to walls/ floor complete including clamps for securing pipe complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints fixed to walls/ floor complete including clamps for securing pipe complete all as specified and directed.

S&F in repair PVC (SWR) vent cowl 110mm dia complete all as specified and directed.

S&F in repairs PVC (SWR) bend with access door of 110mm bore complete all as specified and directed.

S&F in repairs PVC (SWR) bend with access door of 75mm bore complete all as specified and directed.

S&F in repair PVC (SWR) 110mm dia in junction single, (Single T) equal or unequal complete all as specified and as directed.

S&F in repair PVC (SWR) 75mm dia in junction single, (Single T) equal or unequal complete all as specified and as directed.

S & F in repair 75mm dia of outlet PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

Complete removal existing treatment of wall and applying two coats of Oil Bound Distemper of approved shade/tint over a coat of priming paint complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F 2nd class HW boarding 20mm thick fixed with nails as in eaves board planed one side with butt joint including dismantling boarding of any description complete all as specified and as directed.

M&L for 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with nails as in ceiling,including dismantling wall and ceilling boards of any description including cover fillets complete all as specified and directed.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section of unframed work complete all as specified and as directed.

M&L for 2nd class hard wood plain fillets bullnosed, splayed, chamfered or rounded on one edge or face in section clean sawn, fixed with screws sec are exc 6 sq cm n exc 13 sq cm complete all as specified and as directed.

M&L for 2nd class hard wood plain fillets bullnosed, splayed, chamfered or rounded on one edge or face in section clean sawn, fixed with screws sec are exc 3 Sq cm and n exc 6 sq cm complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description n.exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for complete removal of existing treatment from external surface of wall and applying two coats of weather proof paint (Exterior grade) over a coat of alkali resistant primer,complete all as specified and directed.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as including dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed. specified

S & F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as including dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

M/S UTTAM SAHA

M/S U.K ENTERPRISE

Bharara construction

M/s Sohini Construction

M/S MANOJ KUMAR BAL

N.K.TRADING COMPANY

M/S SAMAL CONSTRUCTION