PROVN OF CERTAIN MINOR ADD ALT AND SPECIAL REPAIR WORKS OF AGE BR I AND AGE BR II UNDER GE C KIRKEE

Amount

Demolition of cement concrete (unreinforced) in ground floors and paving below or above GL complete all as specified and as directed.

Demolition of Trellis work (Jafri), two way including taking as under of battens in trellis of spacing Exc 15 cm (posts and rails measured separately) complete all as specified and as directed.

Taking down chowkats and frame exc 1.5 Sqm but n.exc 4.00 sqm each including shutter wiuthout taking off shutter from the frame and removing from site complete all as specified and as directed.

S & F Pressed steel frames made of 1.25 mm thick MS Sheet size 105x60mm for doors, ventilator with single rebates including necessary fixing lugs, hinges, lock strike plate etc with and including providing PCC 1:2:4 type B1 (using 20mm graded stone agg) to fill the frame & making good complete all as specified & directed by Engr-in-Charge.

Supply and fix 35mm thick plain, framed panelled factory made shutters (two panels) door with lock rail and panel of 12mm thick veneered wood board with commercial veneering on both faces and with second class hard wood rails and styles. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F for Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F for Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and as directed.

S&F for mild steel Chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 complete all as specified and as directed.

S & F 200mm long Aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S & F Aluminium handles, cast type, anodised of size 150mm, fixed with screws or welded, complete all as specified and as directed.

S & F aluminium anodised sliding door bolt plate type, not less than 12 mm dia with and including aluminium of 6 bolts and nuts, 4 on bolt plate and 2 on staple plate length of bolt 300 mm welded to door shutter/frame all as directed by Engr-in-charge.

Dismantling Single/double layer Mangalore pattern or similar tiles or ridge in roofing complete all as specified and as directed.

S&F roof tiles, Mangalore Pattern, interlocking at side joints laid dry complete all as specified and as directed.

All as per item No 13 above but except Mangalore tiles complete all as directed. (Note: Material shall be used from dismantling)

S & F for 0.63mm Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 120 Gms/Sqm including dismantling of plain or corrugated steel sheeting any gauge thickness including Nainital or similar pattern as in roof covering complete all as specified and as directed.

S & F for plain, galvanised mild steel sheeting in ridges hips valley gutters drip and straight flashing (length and girth as fixed) by using 1.00mm thick sheet grade of zinc coating @120 Gms/Sqm both sides and welded or soldered joints are provided including dismantling of plain or corrugated steel sheeting any gauge thickness including Nainital or similar pattern as in roof covering/valley gutters complete all as specified and directed.

S & F second class soft wood clean sawn battens at 30 cm centre to centre and sectional area exceeding 15 Sqcm and not exceeding 25 Sqcm including dismantling Battens for tiles, singles etc of any size including tiling fillets spaced exc.15 cm complete all as specified and as directed.

S & F second class hard wood clean sawn in scantlings including dismantling timber in scantling 40 sq.cm and over in section in any position and any description unframed work complete all as specified and as directed.

S & F 2nd class HW plain fillets, rails, rafters, purlins, square, rectangular in section clean sawn secured with nails brads exc 13 sqcm but n exc 25 sqcm including dismantling timber scantlings in fillets, rails, posts, rafters, purlins etc under 40 sq. cm in section (Unframed work) in any position complete all as specified and as directed.

S & F for E-board 'Everest' make 595x595x4mm thick white prelaminated sett embossed reinforced designer ceiling board tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centers securely fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers of GI wire 4mm dia to be fixed by approved rawl plug, level and justers and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm center to form 1200x600mm modules cross tee longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long cross Tee centrally between the 1200mm cross tee. Tee, Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour complete all as specified and as directed.

M&L for Preparing surfaces of wood and wood based materials new or old of any description and girth, not other wise described and treated with two coat of creosote oil complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 ( Using 40mm graded agg) as in foundation and mass concrete complete all as specified and as directed.

M&L for RCC nominal mix types A1 1:1.5:3 (20mm graded aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for RCC nominal mix types A1 1:1.5:3 (20mm graded aggregate) as in beam, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L Mild steel bars 10mm dia TMT bar and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All As per item No.25 above but 5mm dia and over up to and including 10mm dia in stirrups spacers and binders complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

M&L for precast cement concrete block massonry with solid block exceeding 10cm in width and setting in CM (1:6) PCC 1:3:6 type C1 using 20mm graded agg.

M&L for rendering 10mm thick cm (1:6) on fair faces of brick work or concrete surfaces including finishing even & smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cm (1:4) on fair faces of brick work or concrete surfaces including finishing even & smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick screed bed or bedding layer of cement mortar in CM (1:6) for laying of floor tiles complete all as specified and directed.

M&L for Vitrified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M & L for 25 mm thick PCC (1:2:4) type B1 using 20mm graded stone aggregate as in floor, pavings etc, finishing the surface fair and even without using extra cement complete all as specified and as directed.

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with 10mm thick screed bed in cement mortar 1:4 set and joined in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M & L for 75mm thick cement concrete 1:3:6 type C2, using 40 mm graded stone aggregate as in plinth protection/path and finishing surface even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new plastered surface of wall and applying two coat of oil bound distemper white or tinted over a coat of chalk whitening primer complete all as specified and as directed.

M&L preparing the new concrete or plastered surface of wall and applying two coat of cement base paint over one coat of white wash complete all as specified and as directed.

M&L for coloured glossy finish chequered cement concrete tiles of size 30 cm x 30 cm x25 mm thick with grey cement and pigments, set jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed in CM 1:6 and hacking/roughning of old concrete surface complete all as specified and directed.

Demolition of brick work of any type built in cement mortar including all quoins arches pillars etc but exceeding ashlar facing dressed stone work and pre cast concrete articles complete all as specified and directed.

Surface excavation n. exc 30cm deep and averaging 15cm deep and getting out soft/loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out soft / loose soil complete all as specified and directed.

M&L Spreading, levelling, well ramming and including watering in layers n exc. 25 cm thick complete all as specified and directed.

Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) Type B0(12.50mm graded aggregate as in DPC on plinth beam with and including mixing of water proofing compound as per manufactures instruction or as directed at site and necessary form work all as specified and directed.

M&L for sand filling under floor or in foundation or around cables in trenches for cable protection including watering and consolidation all as specified and as directed.

M&L for Hard core of broken stone of gauge exc 63mm but n.exc 100mm, deposited, spread and levelled in layers n. exc 15cm thick, watered and rammed to a true surface all as specified and directed.

M&L Cement concrete 100mm thick type D-2 (1:4:8) using 40mm graded stone aggregate as in sub base of floor all as specified and directed.

M&L PCC 25mm thick 1:2:4 of type B0 using 12.5mm graded stone aggregate as in bases of floors all as specified and as directed.

M&L for machine cut mirror polish kota stone slab flooring 20-25mm thick over 20mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including round nosing at corners, rubbing and mirror polishing complete as specified and as directed.

M&L for machine cut mirror polish kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 20mm thick cement screed base in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including round nosing at corners, rubbing and mirror polishing complete as specified and as directed.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs exc 5 cm but in exc 10 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work rough finished surface of concrete complete all as specified and directed.

M&L for RCC Nominal mix Type B1 1:2:4 (20mm graded aggregate) as in Chajjas/Lintel all as specified and directed.

M&L Reinforcement cement concrete type B1 Nominal mix(1:2:4) using 20mm graded stone aggregate as in cooking plate form/shelves slab complete all as specified and directed.

M&L for rendering 15mm thick on other than fair faces of brick or concrete surfaces of wall in CM 1:4 complete all as specified and as directed.

M&L rendering 15mm thick other than fair faces of brick work or concrete surfaces of wall in CM 1:6 complete all as specified and as directed.

S&F rolled MS section as in Roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc fixed with angle cleats or other connecting plates confirming to Fe 410-W quality B complete all as specified and as directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410-W quality B complete all as specified and as directed.

M&L Mild steel screw bolts ( machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers hexagonal or square and one nut, dia of shank 5 to 10 mm exc 5cm and n.exc 10 cm complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and as directed.

S & F for plain, galvanised mild steel sheeting in ridges hips valley gutters drip and straight flashing (length and girth as fixed) by using 1.00mm thick sheet grade of zinc coating @120 Gms/Sqm both sides and welded or soldered joints are provided complete all as specified and as directed.

S & F for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-410-W(Gde- E-250) quality-A complete all as specified and as directed.

S&F 1 mm thick mild steel plain black sheet in hearths, covering to door chowkats (frames) chullah hoods, water tanks, water troughs, ducts, urinal trough and funnels etc, cut to size, edge beaded if directed, holes punched, including round headed screws, clout nails or rivets and fixed to wood or steel members, etc with plain 40 mm lap joints or welded /riveted seams including bending, turning up, mitred angles, stopped ends, outlets etc as required complete all as specified and as directed.

S&F for 100mm long butt hinges, medium weight, cold rolled mild steel, and fixed/welded with steel frames complete all as specified and as directed.

M&L preparing new steel surfaces over 10 cm width or girth and applying two coat synthetic enamel paint complete all as specified and as directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 Sqm in each pane complete all as specified and as directed.

M&L framed work such as grills grating etc with end of bars shouldered and/or riveted welded or forged into spikes framed guard bars iron doors ladders framed ballusters walk ways railings, frame work of water tanks and similar work confirming to Fe-410 complete all as specified and as directed.

M&L preparation of new steel surfaces and applying two coats of synthetic enamel paints over a cot of red oxide primer complete all as specified and as directed.

M&L Preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed.

M&L Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ complete all as specified and as directed.

S&F Powder coated aluminium partition window for reception counter having section size 63.50mmx38.10mmx1.50mm including 5mm thick float glass and including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws with all necessary fittings etc complete all as specified and as directed by Engr-in-Charge.

Demolition RCC (reinforcement cut as required to facilitate demolition) as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work including removal of debries complete all as specified and as directed.

M&L for RCC types A1 1:1.5:3 (20mm graded aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Taking down cement plaster on brick or stone walls or concrete surfaces etc., including raking out joints, hacking for key scrubbing down with water complete all as specified.

M&L for rendering 5mm thick plaster in cm (1:3) as in ceiling on fair faces of brick work or concrete surfaces including finishing even & smooth without using extra cement complete all as specified and directed.

M & L for 75mm thick Cement concrete 1:4:8 Type D-2 (using 40mm graded agg) as in sub base of interlocking or chequered tiles complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and directed.

M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular area of each tile exc 0.11 Sqm but n.exc 0.18 Sqm in floors etc over and including 15mm thick screed bed in CM 1:6 set and joined in neat cement slurry and pointed in white or coloured cement to match all as specified and directed.

Taking down chowkats and frame n exc 1.5 Sqm each including shutter wiuthout taking off shutter from the frame and removing from site complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified.

S&F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in M.S. frame welded sealed to the stiles and rail with suitable PVC sheet beading and jointed together with solvent cement supply and fixing in the frame at site as per specification and drawing and complete all as specified and directed.

S&F for Aluminium, anodised, tower bolt, length of bolt in mm 150 mm of extruded section, complete all as specified and as directed.

S&F for Steel ventilator with top hung shutter including hinges, steel peg stay, glass panes, complete all as specified and directed.

M&L three coats of white wash including preparing the new concrete or plastered surface of ceiling complete all as specified.

M & L for water proofing treatment comprising of the following using APP membrane polymer based to roof slab/Chajjas including taking down old water proofing treatment of any type and removing the rubbish from the site to a distance exc 500mtrs and n.exc 1000mtrs and deposited in low line areas complete all as specified and as directed by Engr-in-Charge:- (a) 15 mm thick rendering in CM(1:4) on roof /concrete surface with and including 3% WPC by weight of cement. (b) Apply one coat of bituminous primer @ 0.25kg/sqm. (c) Laying APP polymer modified membrane by torch application method. (d) Apply a coat of solar reflective bituminous aluminum paint @ 0.15kg/sqm. (e) 24 hours ponding test after laying WP membrane.

S & F in repair water closet (Squatt Pattern) complete including provision of lime concrete bedding Orissa pattern size 580 x 440mm white integral foot rests (excluding flush pipe or flushing cisterns) including S&F PVC P trap 100/110mm bore dia, 100/110mm PVC (SWR) WC connector with lip ring and connection to flushing pipe anti syphonage pipe etc complete and making good to floor complete all as specified and directed.

S & F in repairs Vitreous china wash down water closet pan (Pedestal pattern) white (excluding fixing bolts, flushing cistern and flush pipe) but including plastic water closet seat, black, closed pattern with flat bottom and cover and mild steel CP or aluminised hinging device complete all as specified and directed.

S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)complete all as specified and directed.

S&F in repair PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle (incl brackets & flush pipe PVC 32 mm dia) capacity of 10 Liters complete all as specified and directed.

S&F in repair vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

S&F in repair pillar tap cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F for steel water tubing 15 mm bore medium grade galvanised with all fittings (ISI marked) fixed complete to walls, ceiling or laid in floors including Taking up or down steel ubing and connections, including cleaning for refixing or removal to store complete all as specified.

S&F for steel water tubing 20 mm bore medium grade galvanised with all fittings (ISI marked) fixed complete to walls, ceiling, laid in floors or trenches including Taking up or down steel ubing and connections, including cleaning for refixing or removal to store complete all as specified.

S&F in repair angular stop valve (ISI Marked), fancy type, chromium plated with long shank and cup (concealed type). screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore complete all as specified.

S&F in repair Bib tap 15 mm bore cast copper alloy CP, fancy type (long shank)., with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed, complete all as specified.

S&F in repair Stop valve (ISI Marked), cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 20 mm bore and fixed complete all as specified.

S&F in repair 15 mm dia PVC connection pipe 450 mm long with two nuts fly nuts complete all as specified and as directed.

S & F Rotational moulded polyethylene water storage tanks 500 lts capacity, double layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed including taking out existing unserviceable overhead tank of any description in any position complete all as directed.

S&F in repair PVC(SWR) sewage pipe 110 dia single socket in any length with rubber ring joints fixed to wall or floor complete all as specified.

S&F in repair PVC(SWR) sewage pipe 75 dia single socket in any length with rubber ring joints fixed to wall or floor complete all as specified.

S&F 100/110mm bore PVC (SWR) bends any radius, duck's foot or heel rest complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) bends any radius, duck's foot or heel rest complete all as specified and directed.

S&F in repair for 100/110mm bore PVC (SWR) reducers complete all as specified and directed.

S&F in repair for PVC (SWR) cowl suitable for pipes of 75 mm bore complete all as specified and directed.

S&F in repair for PVC (SWR) floor trap, Diameter of outlet 75 mm plain with grating including jointing with solvent cement complete all as specified and directed.

M&L for pre cast cement concrete solid block masonry 10cm thick with solid block of the grade C-1, (1:3:6) using 20mm graded stone aggregate set in CM (1:4) complete all as specified and directed.

M & L rendering 15 mm thick on concrete surfaces in CM 1:6, finished even and smooth 'with sagol complete all as specified and as directed by Engr-in-Charge.

M & L for preparing newly plastered surfaces of wall including preparation of surfaces and applying two coats of oil bound distemper over a coat of primer over 3mm thick wall care putty on wall surfaces complete as specified and directed.

M & L for cutting opening through walls built in cement mortar for door, window and other openings or enlarging existing openings, etc, or cutting out defective masonry or underpinning including providing, fixing and removing, shoring, cleaning and stacking stone/bricks and removing surplus to store and rubbish off the premises complete all as specified and directed.

M & L for forming jambs, etc., to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, new work built in cement mortar 1:6 complete all as specified.

M&L for formwork to sides of pillars, posts, struts, piers, columns, lintel and stanchions rough finished surfaces of concrete square, rectangular or polygonal complete all as specified and as directed.

M & L for preparation of plastered or unplastered old decorated surfaces of walls including brooming down or scraping down with steel wire brushes of smoke spots, moulds, moss efflorscent salts and treading oil and greasy spots and applying two coats of oil bound distemper over 3mm thick wall care putty complete all as specified and directed.

M&L for coloured non skid ceramic tiles 300 mm x 300 mm x 6 to 7mm thick, in floors set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in CM 1:6 all as specified including dimolition of floor or wall tiles, stone slab of any description or thickness laid, bedded and pointed in any mortar all as specified.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs any thickness, including cover fillets complete all as specified.

S & F Gypsum reinforced boards 600x600x8-10mm thick for ceiling hot dipped galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4mm dia to be fixed by approved rawl plugs, level and justers and screws etc, The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm from adjacent center to form 1200x600mm moulds cross tee longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long cross tee centrally between the 1200mm cross tee. Tee perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacture instructions and finishing the surface by applying two coats of plastic emulsion paint complete all as directed.

S & F in repairs cast copper alloy CP shower rose 125mm size with swivel joint including fixing to steel pipe complete all as specified and as directed.

S&F in repair Vitreous china wash basin, white, flat back, size 630x450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe all as specified and directed.

S & F in repairs viterous China urinal, half stall type, white including flushing cistern, flush pipe and including providing and fixing plugs, bedding urinal against wall in CM1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back complete all as directed and as specified.

S&F flush pipes PVC 32mm dia for low level flushing cisten to pedestal pan, including all joints, cones, India rubber (nozzles of W.C pans) all as specified and directed.

M&L 32mm dia waste fittings for pipe, brass chromium plated for glazed ware sinks, basins, etc and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and directed.

S&F in repairs towel rail 600mm long 20mm dia brass chromium plated fixed with wooden guities embeded in cement mortar (1 : 3) with steel screws etc, complete all as specified.

S & F in repairs stop valves CP cast copper alloy fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe 15mm bore dia all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

S&F 110mm dai PVC (SWR) bends any radius all as specified and directed.

S&F 75mm dai PVC (SWR) bends any radius all as specified and directed.

S & F low density polyethylene ( LDPE ) pipe 40mm bore of pressure rating 6kg/sq. cm complete all as specified.

S&F in repairs cast copper alloy CP health faucet with 1m flexible pipe for EWC all as specified and directed by EIC.

S&F in repairs Soap dish brass CP all as specified and as directed.( Make- CERA Cat part no CA 103 or equvalent of MARK, JAQUAR)

S & F PVC connections 15mm dia with brass nut on both ends and washers 450mm long all as specified and as directed.

Taking down shutters of any description exc 1.00 sqm but n.exc 2.00 sqm each all as specified and as directed.

S&F Flush shutters 30 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides with covered with decorative face verneer with lipping/frame to match complete all as specified and as directed.

S&F aluminium louvered ventilators of frame section size 80mmx20mmx1.50mm including 5mm thick frosted glass fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh of 0.56mm dia 1.4mm apperture fixed type on outside frame etc. complete all as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as directed.

Material and labour for preparing new or previously untreated wood surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

M & L for preparation of old painted wooden surfaces of any description not otherwise described over 10 cm width or girth and aplying two coat of synthetic emamel paint complete all as specified and as directed by Engr-in-Charge.

Cutting existing CI/GI pipe of any die & insert of new CI/GI Tee all docketed of 100 x 100 x50 mm die including run lead joints/flange joint ,addition/ alteration work complete for branch connection as directed by Engr in charge.

S & F steel water tubing medium grade galvanised with and including all medium grade fitting, fixed complete to walls and ceilings or laid in floors /trenches 25mm bore dia pipe including taking up or down unsv GI tubing of size 15 to 25mm dia all as specified and as directed by Engineer-in-Charge.

S&F gun metal gate valve, cast copper alloy, screwed down, high pressure with iron wheel handle, screwed both ends for iron pipe or unions of size 20mm die complete all as specified.

S&F gun metal gate valve, cast copper alloy, screwed down, high pressure with iron wheel handle, screwed both ends for iron pipe or unions of size 25mm die complete all as specified.

M&L for bed to drain pipes including packing under and haunching in PCC 1:3:6 type C2 using 40 mm graded stone aggregate against the side of SWG/RCC pipes after they are laid and tested for 150mm dia bore pipe all as specified.

M&L for 200 mm dia (internal dia) RCC hume pipe class NP-2 laid and jointed complete with collers complete laid in trenches all as specified and as directed.

Cutting into existing manholes for connecting new drains, Internal dia of pipe 200mm, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required all complete.

M & L for providing cement concrete type B-1 (1:2:4) using 20 mm graded crushed stone aggregate as in coping/benching and the like including necessary form work complete all as specified.

Supply only liquid water proofing compound pidilite LW complete all as specified and directed.

Removing excavated material exc. 1.50 km but n exc. 5 km and depositing where directed.

M & L for PCC 100 mm thick 1:2:4 type B2 as in hardstanding/floor (using 20mm graded stone aggregate) finished even & smooth without using extra cement complete all as directed.

Surface excavation n. exc. 30cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed

M&L for providing Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for Coloured Machine pressed precast concrete interlocking paver block glossy finish (Two colour combination) any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement and pigment laid over sand cushion complete all as specified and directed.

M&L brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radious and built in cm 1:4 all as specified and as directed.

Mild Steel TMT steel bars as in reinforcement 6mm to 8mm dia cut to length bent to shape as reqd etc and over cut to length bent to shape, required including cranking benchings spirally hooping for colums hooking ends and binding with and including mild steel wire annealed) not less than 0.9mm dia all as specified and directed.

M&L precast Cement Concrete 1:2:4 type B1 (using 20mm graded stone agg) as in cover slabs for man holes etc set in cement mortar 1:6 including necessary form work complete all as specified and directed

M&L for PCC 1:3:6, type C-1, using (20mm graded stone agg.) in surface channel and drain.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement , including forms,moulds mitred/stopped ends etc.

M&L for Concrete bed to drain pipe 150mm bore laid to falls including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D2 (using 40mm graded crushed stone agg) complete all as specified and directed

M&L for Reinforced concrete pipes, class NP2, laid and jointed complete with collars 150mm bore laid and jointed on cancrete bed complete including testing complete all as specified and directed.

M & L for soakage pit including excavation in soft disintegrated rock/hard rock, foundation in PCC (1:5:10) type E2, walls brick work in CM (1:6) , RCC (1:2:4) type B1 slab covers, filling with brick bats, complete of size 1.11x1x1.2 mtr all as specified and shown on drawing No CEPZ/90/TD/13 Sh 1/1 dated 19.07.1990.

S&F of aluminium grill of aprature 75x75mm and section of grill 3.5x5.7mm PM type as per approved sample fixed to aluminium frame including all necessary joining cleat/beads complete all as specified and dicirected by Engr-in-Charge.

S&F Anodised aluminium frame powder coated for doors, windows, ventilators with one or more rebates, frames for fixing wiremesh any size including joining cleat for fixing etc. complete all as specified.

S&F Anodised aluminium door shutters, powder coating of any colour (Thickness or powder coating not less than 50 micron) aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

S & F Wire netting of stainless steel wire 0.71mm dia and Size of mesh in 12 mm fixed with tinned tacks of stainless steel wire staples complete all as specified.

Extra for forming fair finished drain or channel 40cm inner girth in cement concrete using extra cement , including forms, moulds mitred/stopped ends etc complete all as specified.

M&L for RCC nominal mix types A1 1:1.5:3 (20mm graded aggregate) as in columns, pillars, piers, posts and struts complete all as specified and as directed.

S & F aluminium alloy butt hinges with galvanized mild steel hing pin, 100 mm size etc all as specified.

S & F aluminum handle cast type anodized size 125mm etc all as specified.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished flat surfaces of concrete etc complete.

M&L for Rendering 15mm thick in cement mortar 1:6 on PCC block walling or concrete surfaces, finished even and smooth without using extra cement complete.

M&L for preparation of new plastered surface of walls and applying two coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surface of of walls and applying two coat of cement base paint on walls complete all as specified and directed.

M&L Figured glass, pin headed type, 3mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq.m in each pane all as specified.

Supply and fixing steel water tubing `medium grade’ galvanized 15 mm bore with all fittings and fixed complete to walls and joints fixed with adhesive complete all as specified & directed.

Supply and fixing steel water tubing `medium grade’ galvanized 20 mm bore with all fittings and fixed complete to walls and joints fixed with adhesive complete all as specified & directed.

S&F in repairs Viterous China water closet squatting pan, 'Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete including connectoin to trap, and to flushing pipe, anti syphonage pipe etc. including trap set in and including concrete and making good to floor.

S&F stop valves 15mm bore cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed complete all as specified and as directed.

S&F bib taps,15mm bore cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified.

S&F rotantional moulded polythylene water storage tanks 500 ltr capacity (cylindrical vertical with closed top ) hoisted and fixed in position complete with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwd for iron pipe 20mm bore omplete all as specified and directed.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 Grade.

Provision of on site LLDPE 10 users septic tank with upflow filter including media designed to carry sewage and sullage water, including excavation earth work in any type of soil in foundation and necessary returning filling and ramming and removal upto 50m, in any type of soil, PCC 1:4:8 below foundation, PCC (1:2:4) type B-2 as in base, brick work in CM 1:4, RCC slab cover including RCC precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame Vent shaft, connection and sludge chambers etc., complete.

M&L plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregates) as in foundations, filling and mass concrete including manholes etc complete all as specified and directed.

M&L for rendering on concrete/ masonary surfaces of walls etc in CM (1:3) 15 mm thick including using waterproofing compound at the rate of 3% by weight of cement and finishing even and smooth without using extra cement complete all as specified and directed.

Supply only approved integral waterproofing compound.

Dismantling battens for tiles singles etc of any size including tiling fillets spaced exc 15 cm complete.

Dismantling timber framed work scantlings 40 sq.cm and over in section, in any position.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction but welded tubes confirming to I.S. 1161-1979 grade St. 240 etc as in purlins complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out and removing surplus soil to a distance n exc 50 m and making good surface in soft and loose soil.

M&L for 40 mm thick PCC 1:2:4 Type B0 using 12.5 mm graded stone aggregate as in flooring, mass concrete finished even and fair all as spd and directed.

Removing surplus excavated soil exc 250m but n.exc 500m and depositing where directed at a level n. exc 1.5m above the starting point.

M & L Plain Cement Concrete Type B2 1:2:4 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete.

Taking down carefully existing unserviceable aluminum / copper point wiring of any description & in any position with and including existing steel conduit / PVC Conduit / Casing capping fixed on surface/wall/angle/girder and including all fitting, accessories & fixtures such as switches, ceiling roses, pendants, regulators, sockets, etc including sunken boxes/junction boxes and making good the disturbed surface of walls, floors, ceiling etc to match with the existing surfaces complete all as specified and directed.

Material and Labor for point wiring concealed type with and including two runs of 1.5 Sqmm (22/0.3mm) multi stranded copper conductor (FRLSH) PVC insulated single core 1100 volts grade wire & one run of 1.5 Sqmm (FRLSH) single core multi stranded copper conductor PVC insulated 1100 Volts grade wire green in color for continuous earthing complete in and including non metallic PVC conduit including all fittings such as elbow, bends, junction boxes, saddles etc. to be terminated in and including suitable size of sheet metal box 1.6mm thick (ISI Mark), screws and rowel plug etc. and connected to light/fan and common earth dolly with 3 mm thick plastic laminated sheet cover for mounting, switches, sockets, fan regulator etc. for one light point or one fan point controlled by one switch including making good the disturbed wall and painting the same with matching to existing wall all as specified and directed by Engineer .

All as per item No 192 above but for one 5 Amps socket outlet on same board with other switch.

All as per Srl item No 192 above but point wiring for 5 pin switch socket outlet combination, 5 Amps on independent board.

All as per item No 192 above but for one 15 Amps socket outlet on independent board with 2.5 sq mm cable .

M&L for point wiring in non metallic PVC conduit of suitable size but not less than 20mm including all fittings such as elbow, bends, junction boxes, saddles, etc. on surface with and including as per IS specification two runs of PVC insulated unsheathed multistranded copper conductor cable (FRLSH) 1.5 sq mm nominal cross sectional area, 1100 volts grade and including one run of 1.5 sq mm (green color) ISI marked PVC insulated unsheathed multistranded (FRLSH) copper conductor cable as earth wire to be terminated in and incl steel sunken box of suitable size with 3 mm thick plastic laminated sheet cover for mounting, switches, sockets, fan regulator etc. for one light point or one fan point controlled by one switch including making good the disturbed wall and painting the same with matching to existing wall all as specified and directed by Engineer in charge.

All as per item No 196 above but point wiring for 5 pin socket outlet, 5 Amps on same board with other switches.

All as per item No 196 above but point wiring for one five pin socket outlet, 15 Amps & 5 Amp on independent board using 2.5 sq mm two run and one run 2.5 sq mm (nominal area) stranded copper conductor cable.

Supplying & Fixing 5 Amp switch piano type single pole one way all as specified and as directed.

Supplying & Fixing 15 Amp switch piano type single pole one way all as specified and as directed.

Supplying & fixing Socket outlet 3 pin, 5A, flush type, multipurpose, 230 volts AC circuit complete all as specified & directed.

Supplying & fixing switch flush type, 15 Amps, single pole, one way , 230 volts AC circuit complete all as specified & directed.

Supplying & fixing ceiling rose PVC/polycarbonate, isolated body, three terminals, complete all as specified & directed.

Dismantling and Taking out old unserviceable light fittings any type from any location complete all as specified and directed.

Supplying, fixing, connecting up to existing/new ceiling rose and testing surface mounting LED Tube Light Batten Fitting having extruded aluminum housing (heat sink) provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver (SMPS based constant current supply with Output Short-circuit protection, Surge protection & other safety tests as per IS:15885 Part 2/Sec 13) suitable for and including 1x20 Watt 4 feet white color tube lamp including connecting with 23/0.0076 copper conductor flexible twisted three core cable including all accessories (mounting SS clips) and fixing arrangements for fixing the light fitting on wall complete all as specified & directed. Make Havells/C&S/Philips/Bajaj.

Supplying, fixing, connecting up to existing/new ceiling rose and testing surface mounting 2 feet 10 W LED Tube Light Batten Fitting having housing material of aluminum heat sink with shatter proof opal shell of polycarbonate compound including connecting with 23/0.0076 copper conductor flexible twisted three core cable including all accessories and fixing arrangements for fixing the light fitting on wall complete all as specified & directed. Make Havells/C&S/Philips/Bajaj.

Supplying, fixing, connecting in at any height up to existing/new ceiling rose and testing LED 1x18 watt Surface mounting round Down lighter with dome shape opal diffuser suitable for indoor applications. with polycarbonate/Acrylic diffuser all as specified & directed all Make Bajaj /Havells/Wipro/CG/Phillips. NOTE - Quoted rate is deemed to be inclusive of any misc materials required for fixing new luminaries.

Supplying, fixing, connecting in at any height up to existing/new ceiling rose and testing LED 1x12 watt Surface mounting round LED down lighter with dome shape opal diffuser suitable for indoor applications. with polycarbonate/Acrylic diffuser all as specified & directed all Make Bajaj /Havells/Wipro/CG/Phillips. NOTE - Quoted rate is deemed to be inclusive of any misc materials required for fixing new luminaries.

Supplying, fixing, connecting and testing 36 W aesthetically designed 2x2 LED edge-lit ultra slim luminary flat panel for recess mounting in grid/Armstrong type ceiling including suitable LED driver and connecting with 23/0.0076 copper conductor flexible twisted three/two core cable and including mounting accessories complete all as specified & directed. Make Bajaj Cat No BCTBLR 36W LED FP CW or equivalent in Havells/C&S/Philips.

Supply , Fixing , Connecting and testing in replacement of Exhaust Fan 300 mm sweep suitable for single phase 230 volts 50 Hz Ac supply heavy duty with louvered shutters incl mounting frame and fixing arrangements , Making good the disturbed surface area match to existing surface connecting the fan to ceiling rose with and including PVC Insulated flexible copper conductor three core 1.00sqmm cable complete all as specified and directed Make Orient INDUSTRIAL EXHAUST or Bajaj / Khaitan /Havells/Crompton

Supply and fix Ventilating Air fan with double ball bearings non metallic body of sweep 150 mm sweep 900 RPM operating on AC single phase complete with louver shutter and connecting up 3 core PVC insulated PVC sheathed copper wire of size 0.5 Sqmm between ceiling rose and fan terminal.(Make:- Havel’s model - DXWE ,or equivalent in CG,Khaitan, Orient)

Dismantling and Taking out old unserviceable copper/aluminum sub main wiring/Unarmored cable (used as Sub main wiring) from any height of any Size and Core with all connecting accessories include. conduit or casing capping and include. making good to the disturbed wall and painting the same with matching paint as of existing wall all as specified and directed by Engineer in charge.

Material and labor for Sub main wiring at any height with and including two single core PVC insulated multi stranded copper conductor cable, FRLSH type, 4.0 Sqmm, 1100 volts grade, drawn through and including New PVC non metallic conduit including connected accessories and one single core PVC insulated multi stranded copper conductor cable, FRLSH type, 4.0 sq mm, 1100 Volts grade, as earth continuity wire all as specified and directed by Engineer in charge.

Disconnecting and taking down old switch fuse type distribution Box with MCB/fuse grip TPN/SPN DB 2 Way to 12 Way old type including taking out all cable connections of any description and in any position and making good the disturbed surface to match with the existing surfaces complete all as specified and directed by Engineer in charge.

Supply & fix MCB distribution board SPN 4 way double door with protection level IP43 complete with 200Amps rated bus bar and.(Make:- Legrand/Havel’s/Siemens)

Supply, fixing, connecting & testing double door sheet metal SPN distribution board 8 way with 100 Amps rated copper bus bar, IP 43, IK 09 class, inclusive of Neutral bar, Earth bar complete all as specified & directed. Make - Legrand Cat No 6076 11 or equivalent in /L&T/ ABB/Schneider.

Supply, fixing, connecting & testing double door sheet metal SPN distribution board 12 way with 100 Amps rated copper bus bar, IP 43, IK 09 class, inclusive of Neutral bar, Earth bar complete all as specified & directed. Make - Legrand Cat No 6076 12 or equivalent in /L&T/ ABB/Schneider.

Supplying & fixing in replacement MCB 6 to 32 Amps, single pole and neutral, 10 kA breaking capacity with integrated label holder, sliding bottom clamp, color coded On/Off indication on dolly, IP 20 protected terminals, sliding shutters complete all as specified and directed. Make - Legrand/ABB/L&T/ Siemens.

Supplying & fixing in replacement MCB 6 to 32 Amps, single pole 10 kA breaking capacity with integrated label holder, sliding bottom clamp, color coded On/Off indication on dolly, IP 20 protected terminals, sliding shutters complete all as specified and directed. Make - Legrand/ABB/L&T/ Siemens.

M&L for earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground, earth pit not less than 2.25 meters deep below ground level with top edge of the plate not less than 1.5 mtr below GL connected to and including 25 x 4 mm GI strip up to 7.5 m long by means of GI bolts, nuts, check nuts & washers and connected to earthing test point & earth dolly all as shown in electrical plate No 3 of SSR part I- (2009), earth lead protected with and including 40 mm bore GI pipe light grade and 20 mm bore medium grade watering pipe and testing on completion including excavation & earth work in any type of strata , PCC (1:3:6) type C-I chamber, precast slab 50mm thick in cement concrete (1:2:4) type B1 (reinforced with welded steel wire fabric of XPM, weight not less than 4 Kg /Sq m) with cast iron/ angle frame ,funnel with water pipe , wire mesh and lugs etc complete all as specified and directed by Engr-in-charge.

S&F earth continuity conductor or main earthing lead of size 25 x 4 mm GI strip fixed to wall drawn in conduit/pipe or any other indicated situation for loop earthing etc. incl removal of old as required all as specified and directed.

Excavation in trenches in any type of soil not exceeding 1.5 Meter deep and not exceeding 1.5 meter width and getting out including forming bottom surface & sides to required slope/size as directed by the Engineer-in-Charge.

Excavation in trenches not exc 1.50 m wide and not exc 1.50 m depth for foundation etc or for manhole / laying of pipe not exc 10 sqm on plan and getting out in hard and dense soil complete all as specified.

Returning filling in soil, and including spreading and leveling in layers not exceeding 25 cm thick complete all as specified & directed by Engineer-in-Charge.

Supply & laying un-reinforced precast concrete cable cover class LV type 1, flat size 250mm x 150mm x 40 mm all as specified & directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminum conductor of size 10.0 sq mm 4 core.

Disconnecting and taking out burnt Service Wire aluminum conductor cable of any description and in any position from walls / steel structure / laid in floors any size any core complete all as specified & directed by Engineer-in-Charge.

Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminum conductor 10 sq mm, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4 mm suspension GI wire, one twin core cable flat or circular including dismantling and taking out old burnt electric cable all as directed.

House service bracket (hook type complete with 3.0 m long G.I. pipe 40 mm dia Med. grade, two nos 90o bends. M.S. hook and stay or guy after disconnecting of old one.

M & L for Construction of valve chamber of 700mmx700mm size, with 50 mm thick PCC 1:4:8 type D-2 in foundation, with PCC solid blocks cast using PCC 1:3:6, type C-1, set in cement mortar 1:4, 10mm thick plaster to internal surfaces and external surfaces up to 10cm below ground level and top of floor in cement and sand mortar 1:4, finished even and smooth without using extra cement , 3.15mm thick MS sheet cover including 50mmX50mmX6mm thick MS angle frame fixed in PCC 1:2:4, type B1 coping with 25mmX6mm flat iron hold fasts, handle, hinges with locking arrangements, applying one coat of red oxide primer and two coats of synthetic enamel paint to all steel surfaces and earth work in any type of soil including disposal of surplus soil to a distance not exceeding 50m complete all as directed by Engr-in-charge.

C J Enterprises

vishalconstruction

MANIYA CONSTRUCTION CO.

V.R.PRAJAPATI AND CO.

Shri Sant Cosntruction