Spl repair to bldg No T-86 and T-87 (OR Living) at DBN and sewage line manholes and connected works at OTM Accn under AGE B/R-I at Tibri Mil Stn Gurdaspur.

Amount

Taking down wooden roof trusses, coupled rafters or trussed beams for span 4 to 8mtr complete all as specified and directed.

Dismantling wooden scantlings 40 sq cm and over in section, in any position complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work or stone/boulder masonry built in cement mortar incl all quoins, arches, pillars and precast concrete masonry etc complete all as specified and directed by Engr-in-Charge.

M&L for brick work with old size flyash bricks , straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for brick with sub class 'B' brick, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

M&L for 75 mm thick, PCC 1:3:6 type C1 (using 20mm graded crushed stone aggregate), finished even and smooth without using extra cement.as in plinth protection incl mastik filling in joints complete all as specified.

Taking down cement plaster on brick or stone walls, ceiling etc, including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for rendering 12 mm thick on fair faces of brick work or concrete surfaces ready mix cement plastering incl finishing even and fair (without using extra cement), complete all as specified and directed

All as per Srl item No 10 above but 15mm thick.

Supply only integral water profing compound (admixture : Sika plastocrete plus / FOSROC/ Dr Fixit/ STP/ CICO confirming to IA 2645).

M&L for preparation of new plastered surface and applying two coats of cement base paint over a coat of primer on wall complete all as specified and directed.

M&L for preparation of old plastered surface by complete removal of existing treatment and applying two coats of cement base paint complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer including applying 1mm thick putty complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall by complete removal of existing treatment and applying two coats of oil bound distemper complete all as specified and directed.

S&F for non asbestos fibre cement building boards 6mm thick fixed to aluminium frame work of size 605x605mm with screws in anodised aluminium snap grid frame work to flase ceiling complete all as specified and directed.

Taking down chowkats with shutter exc 1.50sqm but n.exc 4 sqm each (without taking off shutter) from the chowkats complete all as specified and directed.

S&F for pressed steel frame for doors with one or more rebate including necessary fixing lugs, hinges, lock strike, plate etc of size 125x60mm including one shop coat of priming and two coats of synthetic enamel paint complete all as specified and directed.

S&F for pressed steel frame for doors with one or more rebate including necessary lugs, hinges, lock strike, plate etc of size 105mmx60mm including one shop coat of priming and two coats of synthetic enamel paint complete all as specified and directed.

M&L for providing PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as filling in MS frame complete all as specified and directed.

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F factory made glazed and skeleton shutters 35mm thick, 2nd class hard wood open rebated to receive gauge & glass etc edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of number of shutters as specified in SSR Part-I & section 8 clause 8.24 (a) complete all as specified and directed.

S&F steel window 1.25mm thick box type ERW hollow P section of size 60mmx25mm double rebated comprises of glazed & gauged skelton shutter of (required no of gauged shutters and glazed shutters) ERW section 50mmx20mm & 1mm thick with one openable leaf consisting of two number sash bars of T-Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T-Section of size 60mmx25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 (four Nos for each window) including one shop coat of priming and two coats of synthetic enamel paint including taking down old existing window complete with following fittings welded to the frame shutter :- Ref Drg No CE JZ/TD-06/07 (i) Hold fast,150mm long of 12mmX3mm made to shape-04 Nos per window (ii) Handle of Z section 20mmX25mm,100mm long-01Nos per window (iii) MS Tower bolt 150mm long-02 Nos per window (iv) Z sec 20mmX25mm,100mm long stopper -01 Nos per window (v) Cleat 55mm long of hollow square 15mmX12mm-02Nos per leaf (vi) Fabrication & fixing arrangements as Drg No CEJZ/TD-1020/06 (vii) M S guard bar 12mm square bars @150mm C/C fixed horizontly.

S&F aluminium anodized barel tower bolt of extruded section 150mm long complete all as specified and directed.

S&F for aluminium alloy handle fabricated type anodized of size 150 mm long complete all as specified and directed.

S&F for aluminium alloy, anodised, 250 mm sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F in repair 300mm, mild steel ordinary rat tail rod pattern springs, including roller and roller plate, fixing by welding/ bolt in metal/wooden frame or necessary alternative arrangements to be done complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F 4.8mm thick sheet glass ordinary quality and glazing with oil putty in squares n.exc. 0.50 Sqm each complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Dismantling of asbestos cement corrugated or semi corugated sheets in roof covering of any gauge and thickness complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick, ISI marked any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, crumple joint etc fixed with self tapping screws as required complete all as specified and directed by Engineer-in-Charge.

S&F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including taking down old AC sheets complete all as specified & directed.

M&L for steel work in tubular trusses incld special shaped washers etc, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed.

M&L for MS plates square, cut or notched forming holes, without any attachment conforming to Fe 410-W Gde E-250 Quality A, complete all as specified and directed.

M&L for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or suare nut, length of bolt exc 30 cm long,diameter of neck in mm 16 to 20 mm complete all as specified and directed.

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L for PCC 1:3:6 type C1 (using 20mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed by Engr-in-Charge.

S&F in repair drapery rod in any length, high strength stainless steel pipe having outer dia 28mm with a pair of brakets of any shape/ design omplete all as specified and directed.

Demolition stone slabs and tiles of any description or thickness in floors, aprons, counter platforms etc complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.18 sqm not exc 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 20 mm thick screed bed in CM 1:6 and including demolition of existing tiles and screed complete all as spcified and directed by Engineer-in-Charge.

All as per Srl item No 43 above but on vertical surface as in skirting incl 10mm thick screed bed in CM 1:3.

M&L for glazed ceramic coloured tiles in vertical surface of size 450X300x7mm thick joint free on and incl 10mm thick screed bed in CM(1:4) set and jointed in neat cement slurry and pointed in coloured cement mixed with pigment to match the colour of tiles including demolition of existing tiles and screed complete all as speciifed and directed by Engineer-in-Charge.

S&F in repair 18/19 mm thick one side prelaminated colour WPC board for cup board shutter and frame and fixed at site complete all as specified and directed. (Note :- Board edges properly finished with strip on edges)

S&F in repair 18/19 mm thick white WPC board for cup board shutter and frame and fixed at site complete all as specified and directed. (Note :- Board edges properly finished with strip on edges)

S&F aluminium alloyed handle fabricated type anodised of size 100mm long complete all as specified and directed.

S&F 75mm size hasp and staple safety type aluminium anodised brass with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed.

M&L for RCC in 1:2:4 type B-0(using 12.5 mm graded crushed stone aggregate) as in chajjas facia, shelves, lintel etc and similar work complete all as specified and directed.

M&L for TMT bars 6 to 10mm dia cut to length bent to shape required including crancking spirally for hooking ends and binding with and including MS wire annealed not less than 0.9mm dia complete all as specified.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup-posts, overhanges etc also splays between floors and beams etc complete all as specified and directed.

Taking down dement plaster/ deteriorated concrete from bottom of RCC chhajja/ RCC facia/ RCC beam/ RCC slab/ brick work including racking out joints, hacking for key, scrubing down with water (at a bldg height upto 4.50 mtr) and removing rubbish to a distance exc 50 mtr but not exc 100 mtr away and M&L for 15mm thick plaster in CM 1:3 finished even and smooth without using extra cement on bottom of RCC chajja and RCC facia complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (40 mm graded crushed stone aggregate) as in sub base foundation of manholes etc complete all as specified & directed by Engineer-in-Charge.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

Dismantling existing tiles/ blocks and M&L for 60mm thick PCC (M-35) factory made coloured interlocking tiles/ paver block of shape and size as conforming to IS-15658, joints will be filled with fine sand complete all as specified and directed.

Excavating in trenches in soft/ loose soil n. exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes etc. n exc 10 sqm on plan and getting out all as directed.

All as per Srl item No 57 here-in-before but ex 1.5 mtr and n.exc 3 mtr.

Returning filling in the soil including spreading, levelling, watering and well ramming in layer n.exc 25cm thick each layer complete all as specified and directed.

Removing excavated soil to a distance not exc 50m away and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

Demolition and breaking up 150 mm drain pipes (SGSW/ AC/reinforced concrete) set in cement mortar and taking out from trenches all as directed.

Demolition and breaking up 200 mm drain pipes (SGSW/ AC/reinforced concrete) set in cement mortar and taking out from trenches all as directed.

M&L for SGSW pipes 150mm bore grade 'A' including laying pipes to level or to falls in trenches, on concrete bed and all necessary extra joints, waste and cutting complete all as specified and directed by Engineer-in-Charge.

M&L for RCC drain pipes NP3, 150mm bore including laying pipes to level or to falls in trenches, on concrete bed and all necessary extra joints, waste and cutting as jointed complete with collars as specified and directed.

M&L for RCC drain pipes NP3, 200mm bore including laying pipes to level or to falls in trenches, on concrete bed and all necessary extra joints, waste and cutting as jointed complete with collars as specified and directed.

M&L for 100mm PCC 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in concrete bed, width of concrete bedding shall extend laterally 15 cm beyond either side of the outer dia of pipe laid to falls in trenches in any depth including packing under, and haunching against the sides of SGSW/ reinforced concrete drain pipes NP3, 150mm bore, after the pipes have been laid and tested including any necessary shuttering and supports to concrete and for laying beds to falls complete all as specified and directed.

M&L for 150mm PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as concrete bed, width of concrete bedding shall extend laterally 15 cm beyond either side of the outer dia of pipe laid to falls in trenches in any depth including packing under and haunching against the sides of SGSW/ reinforced concrete drain pipes NP3, 200mm bore, after the pipes have been laid and tested including any necessary shuttering and supports to concrete and for laying beds to falls complete all as specified and directed.

Demolition of brick masonry work built in cement mortar including all quions, arches, pillars etc of any description and in any position complete all as specified and directed.

M&L brick work with fly ash old size brick straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed.

All as per Srl item No. 69 here-in-before but except bricks.

Taking down cement plaster, any description on brick or concrete surface or stone walls etc including raking out joint, hacking for key, scrubbing down with water etc removing the rubbish off the premises complete all as specified and directed.

M&L for prepration of newly plastered/un plastered surfaces of wall and applying two coats of white wash complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in surface channel and drain including forming fair finished drain or channel in cement concrete without using extra cement including forms, moulds, mitred/ stopper ends etc complete all as specified and directed.

Dismantling of cast iron, PVC or drain pipes, jointed in cement mortar and taking out of trenches and wall complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall/floors upto 12m height all as specified & directed.

S&F in repair PVC(SWR) 110mm bore bends any radius complete all as specified and directed.

S&F in repair PVC (SWR) 110 mm dia junction single, (Single T) equal or unequal complete all as specified and directed.

Demolition of RCC (reinfocement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for upto 12m height complete all as specified and directed.

M&L for 75mm thick factory made pre cast cover slab n. exc 0.50 sqm with alround angle iron RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in manhole and drain etc and similar work etc complete all as specified and directed.

E/M PORTION Taking down carefully aluminium/copper point wiring for light, fan, bell, socket of point complete fittings such as switches, ceiling roses, pendents, regulator socket etc complete at site and making good disturbed surfaces of walls, floors etc.

M&L for point wiring with PVC insulated and PVC unsheathed multistranded FRLSH copper conductor cable of size 1.5 Sqmm including concealed PVC conduit fittings and making good to the disturbed surfaces with continuous earth wire of copper 1.5 Sqmm dia to common earth including provn of 3mm thick plastic laminated sheet of appropriate size and fixing to CI/MS boxes for mounting of accessories like surfaces sockets and regulators etc. complete all as specified for One light / Fan/ bell point controlled by one way modular switch complete all as specified and directed.

All as per Srl item No 81 here-in-before but 5 Amp socket outlet on independent board.

All as per Srl item No 81 here-in-before but one 5 pin socket outlet 5 amps on same board.

All as per Srl item No 81 here-in-before but on light point controlled by two way switches.

All as per Srl item No 81 here-in-before but wiring with 2.5 Sqmm FRLSH copper wire including one earth wire 2.5 sqmm of copper for 15 Amps 3 pin socket outlet .

M&L for sub main wiring with two single core multi stranded PVC insulated, unsheathed copper conductor of grade 1100 Volt, FRLSH cable of size 6 sqmm (Red for phase and Black for neutral) and including electrical grade PVC conduits of desired colour not less than 1.2mm thick and 32mm dia and 6 sqmm multistranded copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete and taking down old unsedrviceable wiring complete all as specified and directed. Note :- (a) Cost of making good the disturbed surface plastering/ filling putty for matching with the existing colour with MES approved make of distemper is deemed to be included in the quoted rate by contractor. (b) Three run of cable alongwith PVC conduit together shall be measured as single run.

S&F switch piano flush type single pole one way 5 amps.

S&F socket outlet 3 pin 5 amps flush type.

S&F switch flush type 15 amps single pole one way

S&F socket outlet 3 pin 15 amps flush type

S&F switch piano 2 way 5A complete all as specified and directed.

S&F in replacement of LED tube light fitting wall mounted with single side connection polycarbonate LED batten with aluminium housing and integrated electronic driver of capacity 20W, four feet and connection with PVC insulated twin core 23/0.0076 twisted copper cable from ceiling rose to tube light fitting complete all as specified and directed.

S&F wall /ceiling mounting LED 9/10 watt tube light fitting complete with all acessories 1x9 Watt LED , with CCT of 6000k suitable for domestic application, 240 Volts, 50 Hz, and internally pre-wired with 1.5 sqmm twin twisted flexible cable copper conductor and connection complete all as specified and directed.

S&F decorative 9W, LED wall mounting fittings complete set including 9W LED lamp 9 Watt polycarbonate type B-22 complete all as specifed and directed.

S&F PVC insulated sheathed copper wire 1.5 sqmm FRLSH single core 1100 volt for inverter connection in same conduit all as specified and directed

S&F in replacement of fan regulator electronic type 5 step 100 watt, 240 volt and connecting complete all as as specified and directed by Engineer-in-Charge.

S&F lamp holder, PVC/ polycarbonate type insulated body with back plate suitable for batten / angle fittings complete all as specified and directed.

S&F ceiling rose, surface bakelite 65x50mm three terminal all as specified and directed.

S&F GI pipe bracket made out of GI pipe light grade 32 mm dia and bent to shape 1.5m long, MS clamps made out of MS flat iron of size 32mm thick with nuts & bolts, washers including painting to MS clamps with two coats of sythentic enamel paint over one coat of primer red oxide complete including dismentling the existing GI pipe bracket and drilling of holes for nuts & bolts etc complete all as specified and directed.

S&F LED street light fitting 35 Watt 230V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

S&F in repair sheet metal enclosure for DB’s when MCB’s to be used of 240 volt 8 way with 200 amps rated bus bar SPN double door complete all as specified and directed. (Note :- All the connection of incoming and out going wire in MCB will be made with thimble with suitable size as directed).

S&F in repair MCB single pole 6 amps to 32 amps complete all as specified and directed.

All as per Srl item No 102 here-in-before but single pole and neutral 32 amps, C series complete all as specified and directed.

M&L for replacement of distribution board made out of CRCA sheet DB vertical type double door TPN 4 Way MS sheet including fixing in the wall, cutting chases, grounting and necessary patch work finishing the surface to match with the existing including making connections all as directed containing the folowings:- (Note :- All the connection of incoming and out going wire in MCCB and MCB will be made with thimble with suitable size as directed). (a) MCCB 4 Pole 63 Amps 16 KA breaking capacity with thermal release - 01 No (In coming). (b) Bus bar 200 Amp rated made out of aluminium on insulated with wire adhesive tape RYB & black - 4 Nos. (c) MCB SPN 40 Amp - 04 Nos, MCB SP 40 Amp - 04 Nos (Out going). (d) Connection from MCCB to bus bar will be made with aluminium strip of suitable size as directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cm × 60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point including testing on completion including watering, GI pipe 20mm bore medium grade, 15mm bore light grade GI pipe for protection of earth lead including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm including 8mm dia TMT bars both ways @ 15cm centre to centre with one handle for lifting made out of 8mm dia MS bar, funnel and wire mesh, excavation and earth work in soft loose of soil complete including dismantling existing earthing complete all as specified and directed by Engr-in-charge.

S&F wall mounting fan 400mm sweep including all accessories all as specified and directed.

Supply and fixing evaporative desert cooler electric driven (single phase) of capacity 5000 cum/hr steel 1500 RPM 230 Volt body made out of sheet for main body and 22 SWG for side covers duly super enamaled painted with two coat of hammer tone paint ist quality over a coat of red oxide primer complete inner and outer sides with front grill made out of steel (heavy duty) propeller cooler fan (aluminium blade ) 500 mm sweep dia heavy duty AC single phase 230 volt 50 c/s copper wound with submercible pump & including float valve complete all as specified

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core complete al as specified and directed.

Supply and laying brick common burnt sub class "B" old size for protection of cable laid in trenches for under ground cable all as specified.

M&L sand cushioning in trenches using fine sand to under ground cable, laid in two layers 15cm before laying the cable and 8cm after laying the cable complete all as specified.

M&L for cable protection GI tubing light grade fixed long the pole/under road/along the wall of size 40 mm bore with necessary clamps all as directed.

A Schedule of Credit for old/unserviceable demolished/ dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Rs. 99,209/- Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

M/S DARSHAN & CO (BID ID -3496393)