Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹98.2 LAccepted-AOC | ₹98.2 L Quoted ₹100.0 L | L1 | Accepted-AOC Being lowest bidder |
| 2 | L2₹1.0 CrRejected-AOC FLAT NO 203 GH 5 SECTOR 27 PANCHKULA 134116 HRY | PANCHKULA | HARYANA | 134116 | ₹1.0 Cr | L2 | Rejected-AOC Being other than lowest bidder |
| 3 | L3₹1.2 CrRejected-AOC 19192 STREET NO 8 BIBI WALA ROAD OPPOSITE DAV COLLEGE BATHINDA PUNJAB PIN 151001 | BATHINDA | BATHINDA | PUNJAB | 151001 | ₹1.2 Cr | L3 | Rejected-AOC Being other than lowest bidder |
| 4 | L4₹1.2 CrRejected-AOC 368 PHASE 4 SAS NAGAR MOHALI 160059 PB | S A S NAGAR | PUNJAB | 160059 | ₹1.2 Cr | L4 | Rejected-AOC Being other than lowest bidder |
| 5 | L5₹1.2 CrRejected-AOC NEAR MANN SINGH GURUDWARA RAJPUT PATTI BUDHLADA DISTT MANSA PB 151502 | BUDHLADA | MANSA | PUNJAB | 151502 | ₹1.2 Cr | L5 | Rejected-AOC Being other than lowest bidder |
| Sl No | Description | Qty | Unit | M/S MATLOOB AHMED L6 | M/S MANI GARG CONTRACTOR L3 | B N FRIENDS AND CO L2 | M/s R. Krishan and Co. L5 | Anil Kumar Gupta L7 | Harbhajan Singh Sandhu and Sons L1 | Jawandha Enterprises L8 | Baba Engineers and Contractors L4 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1.00 | Demolition of cement concrete in ground floor and pavings not exc 15cm thickness below or above ground level, including removing the debris from the site to a designated place by the civil administration complete all as specified and directed by Engineer-in-Charge. | 16.5 | Cum | 300 ₹4,950 | 400 ₹6,600 | 400 ₹6,600 | 349 ₹5,758.50 | 300 ₹4,950 | 500 ₹8,250 | 750 ₹12,375 | 180 ₹2,970 |
| 2.00 | Taking down cement plaster or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc of any description and any position, including removing the debris from the site to a designated place by the civil administration complete all as specified and directed by Engineer-in-Charge. | 2,660 | Sqm | 35 ₹93,100 | 10 ₹26,600 | 10 ₹26,600 | 19 ₹50,540 | 40 ₹1.1 L | 25 ₹66,500 | 50 ₹1.3 L | 35 ₹93,100 |
| 3.00 | Demolition floor, health or wall tilling including cement mortar bedding but not backing removing the debris from the site to a designated place by the civil administration complete all as specified and directed by Engineer-in-Charge. | 1,840 | Sqm | 30 ₹55,200 | 15 ₹27,600 | 15 ₹27,600 | 19 ₹34,960 | 40 ₹73,600 | 25 ₹46,000 | 50 ₹92,000 | 25 ₹46,000 |
| 4.00 | Taking down chowkhats or frame with shutter (without taking off shutter from the frame) area n.exc 1.5 Sqm each, with and including making good the disturbed surfaces with PCC 1:2:4 type B-0 and rendering in CM 1:4 finished the surfaces and edges to recive window/door chowkhats complete all as specified and directed | 182 | Each | 200 ₹36,400 | 125 ₹22,750 | 150 ₹27,300 | 119 ₹21,658 | 150 ₹27,300 | 100 ₹18,200 | 400 ₹72,800 | 80 ₹14,560 |
| 5.00 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) area exc 1.5 Sqm but n.exc 4 Sqm each, with and including making good the disturbed surfaces with PCC 1:2:4 type B-0 and rendering in CM 1:4 finished the surfaces and edges to recive window/door chowkhats complete all as specified and directed | 208 | Each | 250 ₹52,000 | 125 ₹26,000 | 200 ₹41,600 | 129 ₹26,832 | 180 ₹37,440 | 100 ₹20,800 | 500 ₹1.0 L | 100 ₹20,800 |
| 6.00 | M& L for 25 mm thick (average) cement concrete 1:2:4 type B-0, (using 12.5 mm graded stone aggregate) as levelling course finished even and fair without using extra cement complete all as specified and directed. | 800 | Sqm | 135 ₹1.1 L | 60 ₹48,000 | 100 ₹80,000 | 129 ₹1.0 L | 120 ₹96,000 | 120 ₹96,000 | 225 ₹1.8 L | 120 ₹96,000 |
| 7.00 | M & L for light shade Vitrified ceramic coloured tiles premium quality laid in floors, 8 to 9 mm thick (square/ rectangular) area of each tile exc 0.18 sqm but not exceeding 0.36 Sq.m, with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed in cement mortar (1:6) including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed. | 800 | Sqm | 900 ₹7.2 L | 1,000 ₹8 L | 800 ₹6.4 L | 879 ₹7.0 L | 900 ₹7.2 L | 850 ₹6.8 L | 840 ₹6.7 L | 950 ₹7.6 L |
| 8.00 | M & L for light shade Vitrified ceramic coloured tiles premium quality as in skirting, 8 to 9 mm thick (square/ rectangular) area of each tile exc 0.18 sqm but not exceeding 0.36 Sq.m set and jointed in neat cement paste as required, over and including 10 mm thick rendering in cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed. | 100 | Sqm | 890 ₹89,000 | 1,000 ₹1 L | 800 ₹80,000 | 979 ₹97,900 | 900 ₹90,000 | 850 ₹85,000 | 890 ₹89,000 | 1,000 ₹1 L |
| 9.00 | M&L first quality Non skid ceramic coloured tiles laid in floors 7/8 mm thick, joint free (square/ rectangular) area of each tile exceeding 0.11 Sq.m but not exceeding 0.18Sq.m, with neat cement slurry @ 3.00 kg/Square metre over and including 15 mm thick screed bed of cement mortar (1:6) including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed. | 200 | Sqm | 800 ₹1.6 L | 800 ₹1.6 L | 700 ₹1.4 L | 779 ₹1.6 L | 850 ₹1.7 L | 650 ₹1.3 L | 840 ₹1.7 L | 650 ₹1.3 L |
| 10.00 | M & L for glazed ceramic coloured tiles 450mm x 300mm x 7/8 mm thick on vertical surfaces/dado skirting joint free, set and jointed in neat cement paste as required and pointed in white/colour cement to match over and including 10mm thick cement mortar as in backing coat of tile in cement mortar 1:4, Complete all as specified and directed . | 740 | Sqm | 800 ₹5.9 L | 1,000 ₹7.4 L | 700 ₹5.2 L | 779 ₹5.8 L | 850 ₹6.3 L | 650 ₹4.8 L | 890 ₹6.6 L | 700 ₹5.2 L |
Updated dates
Tender Value
Refer Docs
EMD Value
₹1.7 L
Closing Date
19 Dec 2025, 6:00 pmClosed
CWE AF Chandigarh
HQ CWE AF Chandigarh PIN-160003
SPECIAL REPAIRS TO CERTAIN SMQs AT AF STN CHANDIGARH
2025_MES_738778_1
CWE/AF CHD/CHD/T-17/2025-26
Open Tender
Civil Works
330 days
Chandigarh
As per NIT
8 documents required · 8 mandatory
₹1,000
GE (AF) Chandigarh
₹1.7 L
20 Mar 2026
7 Nov 2025
26 Dec 2025
7 Nov 2025
19 Dec 2025
5 Dec 2025
Amount
Demolition of cement concrete in ground floor and pavings not exc 15cm thickness below or above ground level, including removing the debris from the site to a designated place by the civil administration complete all as specified and directed by Engineer-in-Charge.
Taking down cement plaster or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc of any description and any position, including removing the debris from the site to a designated place by the civil administration complete all as specified and directed by Engineer-in-Charge.
Demolition floor, health or wall tilling including cement mortar bedding but not backing removing the debris from the site to a designated place by the civil administration complete all as specified and directed by Engineer-in-Charge.
Taking down chowkhats or frame with shutter (without taking off shutter from the frame) area n.exc 1.5 Sqm each, with and including making good the disturbed surfaces with PCC 1:2:4 type B-0 and rendering in CM 1:4 finished the surfaces and edges to recive window/door chowkhats complete all as specified and directed
Taking down chowkhat or frame with shutter (without taking off shutter from the frame) area exc 1.5 Sqm but n.exc 4 Sqm each, with and including making good the disturbed surfaces with PCC 1:2:4 type B-0 and rendering in CM 1:4 finished the surfaces and edges to recive window/door chowkhats complete all as specified and directed
M& L for 25 mm thick (average) cement concrete 1:2:4 type B-0, (using 12.5 mm graded stone aggregate) as levelling course finished even and fair without using extra cement complete all as specified and directed.
M & L for light shade Vitrified ceramic coloured tiles premium quality laid in floors, 8 to 9 mm thick (square/ rectangular) area of each tile exc 0.18 sqm but not exceeding 0.36 Sq.m, with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed in cement mortar (1:6) including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed.
M & L for light shade Vitrified ceramic coloured tiles premium quality as in skirting, 8 to 9 mm thick (square/ rectangular) area of each tile exc 0.18 sqm but not exceeding 0.36 Sq.m set and jointed in neat cement paste as required, over and including 10 mm thick rendering in cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed.
M&L first quality Non skid ceramic coloured tiles laid in floors 7/8 mm thick, joint free (square/ rectangular) area of each tile exceeding 0.11 Sq.m but not exceeding 0.18Sq.m, with neat cement slurry @ 3.00 kg/Square metre over and including 15 mm thick screed bed of cement mortar (1:6) including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed.
M & L for glazed ceramic coloured tiles 450mm x 300mm x 7/8 mm thick on vertical surfaces/dado skirting joint free, set and jointed in neat cement paste as required and pointed in white/colour cement to match over and including 10mm thick cement mortar as in backing coat of tile in cement mortar 1:4, Complete all as specified and directed .
Demolition stone slabs and tiles of any description or thickness in floors/ dado, aprons etc., laid bedded and pointed in any mortar, complete all as specified and directed.
M/L Machine cut Pre-polished Kota stone slab flooring 55mm x 55mm x 18/20mm thick as in floor, mid landing of stair case over 15mm thick cement screed of cement mortar 1:6 base laid and jointed with grey cement slurry mixed with pigment to match the shade of stone slab complete all as specified and as directed.
M/L Machine cut Pre-polished Kota stone slab flooring 18/20mm thick as in floor, treads of stairs case over 15mm thick cement screed in cement mortar 1:6 base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, exposed edges rounded and chamfered complete all as specified. Note : (Kota stone fixed in staircase tread shall be of single piece) .
M/L Machine cut Pre-polished Kota stone slab 18/20mm thick as in vertical surfaces, riser of stairs case over 10mm thick cement rendering in cement mortar 1:4 base laid and jointed with grey cement paste,jointed with pigment to match the shade of slab as in risers of steps, skirting, dado complete all as specified and as directed. Note : (Kota stone to be fixed in staircase Riser shall be of single piece)
M & L for Granite (of any type ) 16 to 18 mm thick, work (table rubbed and polished) fine grained 'Z' black/red in cooking platforms/Jambs including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including screed bed 15 mm thick in CM 1:4, exposed edges rounded and chamfered complete all as specified.
Demolition of brick masonry in any position built in any cement mortar, complete all as specified.
M&L Brickwork with sub class 'B' bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), using old size sub class B bricks complete all as specified.
M&L for rendering 15 mm thick on brick or concrete surfaces in cement mortar 1:6 finished even and fair without using extra cement complete all as specified as per directed .
M&L for rendering 15 mm thick on brick or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified .
M&L for rendering 10 mm thick in cement mortar (1:3), as on concrete surfaces in ceiling (such as chajja,beams, roof projection, balcony, mumty and staircase flight ceiling, roof slab etc.) finished even and fair without using extra cement, complete all as specified and directed by Engineer - in -Charge.
M&L for rendering 15 mm thick plaster (1:3) in cement sand mortar with integral water proofing compound for repair of distressed RCC member including scaffolding for suitable working platform as in column, beams, chajja and roof projection, facia by with and including fibre mesh, finishing the surfaces even and smooth without using extra cement and including demolition/ taking down as required comlplete all as specified and directed by Engineer in Charge. Note : (i) Rendering should be done in two layers . First Layer 10mm thick and Second layer 5 mm thick GI wire 0.91mm dia , average size of wire mesh 20 mm fixed with tinned tacks. (ii) Removing all disintegrated and loose portion and cleaning the rust from exposed reinforcement, removing, rusted scales by chipping and cleaning by wire brushes. Note for item no. 19 to 21 :-The unit rate quoted by contractor is deemed to include necessary scaffolding and form work upto 12 Mtr height or (G+2) storey building.
M& L for 75 mm thick Cement concrete type C1, 1:3:6 (using 20 mm graded stone aggregate) in plinth protection, finished even and without using extra cement including forming of construction joint @ 2.5 meter Centre to centre & corner to be filled with bitumen (80/25) and sand in ratio of 1:6 complete all as specified and directed.
Supply and fix, factory made pressed steel frames for doors with one or more rebates, of size 105mmx60mm, made out of 1.25mm thick sheet, including necessary fixing lugs, hinges, lock strike plate, with and including cement concrete 1:2:4 (type B0) with 12.5 mm graded stone aggregate in backfilling of chowkhats complete all as specified and directed.
Supply and fix factory made pressed steel frames for doors with one or more rebates of size 125mmx60mm, made out of 1.25mm thick sheet including necessary fixing lugs, hinges, lock strike plate, with and including 25mm x 50mm MS tube 2mm thick stopper welded to chowkhat and including cement concrete 1:2:4 (Type B0) with 12.5mm graded stone aggregate in backfilling of chowkhats complete all as specified and directed.
Cutting holes in brick walls exc half brick but n exc one brick in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified.
M & L for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified. (Note : Holdfast/ Lugs of mild steel frame single/double rebated shall not be measured and paid under this item).
Supply and fix, factory made flush shutters 35 mm thick,solid core construction with block board core and plywood face panels commercial type on both sides, duly provided with 6mm thick teakwood leaping on exposed edges all around, fitted to chowkats, complete all as specified & directed.
S&F factory made Second class hardwood glazed and skeleton door shutters 35 mm thick, in three equal panels , open rebated and prepared to receive glass, gauze, etc, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete all as specified.
S & F Factory made single rebated extruded WPC (Wood Polymer Composite) solid door/ window frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with mitered joints after applying PVC solvent , screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame ,Class A category with property of being termite/ borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and as directed .(M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately)
All as per description of item No. 29 here in before but frame size-65x125mm double rebated complete all as specified and as directed.
Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain door shutter , 30 MM thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame , Class A category with property of being termite/borer proof, water/moisturproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specfied and as directed by Engineer in Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)
Providing and fixing factory made 30 MM thick 100% solid WPC (Wood Ploymer Composite) plain wiremesh door shutter of required size comprising of virgin PVC resin polymer of K value 57-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives made from extrusion procecess WPC foam sheet single exttruded(Inner) with having minimum density not less than 650 kg/cum of density and screw withdrawal strength of 2000 N (Face) & 1100 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisturproof and fire retardant. For fixing Mosquito mesh and XTN aluminimium mesh combinly panel area of door exceept stiles and rails to be panelled with mesh with self tapping round headedscrews at required distence, scres and edges covered with body theareted PVC edge beading all arround of mesh and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: All connected items e.i. stainless steel butt hinges and wiremess including necessary S.S screws not paid separately)
S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush type as in shutter or exposed member of cupboard of 25 mm thick with Balancing on one face and wooden grain pattern lamination on exposed surface with and including 18 mm wide 1 mm thick PVC leaping on exposed edges to match with shade of shutter fixed with suitable solvent comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame , Class A category with property of being termite/borer proof, water/moisture proof and fire retardant all as specfied and as directed by Engineer in Charge .
S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush shutter or exposed member of cabinet structure of 18mm thick with Balancing on one face and wooden grain pattern lamination on exposed surfaces with and including 18 mm wide 1 mm thick PVC leaping on exposed edges to match with shade of shutter fixed with heatex solvent comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame , Class A category with property of being termite/borer proof, water/moisture proof and fire retardant all as specfied and as directed by Engineer in Charge.
S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush shutter or exposed member of cabinet structure of 25 mm thick with Balancing on one face and wooden grain pattern lamonation on exposed surface with and including 25 mm wide 0.8 to 1 mm thick PVC leaping on exposed face to match with shade of shutter fixed with suitable solvent comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant all as specfied and as directed by Engineer in Charge
Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush Cup board /kitchen cabinet backing of size 06 mm thick Balancing on one side comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame , Class A category with property of being termite/borer proof, water/moisture proof and fire retardant, WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on one face of shutter fixed to wall with necessary full body threaded star headed counter sunk S.S screws and PVC rawl plug or PVC solvent complete all as specified and as directed by Engineer in Charge
S&F 100 mm stainless steel butt hinges, with stainles steel hinge pin & fixed to WPC door using stainless steel screws complete all as specified & as directed.
S&F 75mm stainless steel butt hinges 25mm shuter (22-23mm) for cupborords with stainles steel hinge pin, & fixed to WPC door using stainless steel screws complete all as specified & as directed.
S&F 75mm stainless steel butt hinges, 18 mm shuter(15-16mm) for kitchen shutter with stainles steel hinge pin, fixed to WPC door using stainless steel screws complete all as specified & as directed.
S&F 100mm size Stainless steel Hasp and staple, safety type suitable for 30 mm shutter, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified & as directed. .
S&F Magnetic catcher with 8mm dia steel ball catcher , brass body and striking plate including letting in and fixed suitable for kitchen cabinate/cupboard complete all as specified and directed by Engineer-in- Charge.
S&F, 150mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.
S&F, 200mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.
Supply and fix 150mm size aluminium handle cast type pressed handle Ovel type complete all as specified and directed.
S&F 250 mm long aluminium alloy anodized sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed by Engr in charge.
S&F 300 mm long stainless steel heavy duty, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed by Engr in charge.
S&F spring for doors 300 mm mild steel ordinary rat tail rod pattern spring including roller & roller plate complete all as specified and directed.
S&F 125 mm size stainless steel handles medium duty and fixed with SS screw complete all as specified & as directed.
Factory made box type steel window with two nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer in and including cutting holes in brick walls for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1, complete all as specified and shown on Drawing No CEAF/STD-184-2012 Sheets 1/3 & 3/3 and as directed by the Engineer in Charge.
Factory made made box type steel window with two Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars, including flat iron 12 x 3 mm for securing wire mesh, dovetailed or welded and with one shop coat of zinc chromate primer complete in and including cutting holes in brick walls for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1, complete all as specified and shown on Drawing No CEAF/STD-185-2012 Sheets 1/2 & 2/2 and as directed by the Engineer in Charge.
Factory made box type steel ventilator fixed type, dovetailed or welded and with one shop coat of zinc chromate primer in and including cutting holes in brick walls for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1, complete all as specified and shown on Drawing No CEAF/STD-186-2012 Sheets 1/1 and as directed by the Engineer in Charge.
Factory made made box type steel ventilator with glazed shutter or gauzed shutter with glazing bars or flat iron 12 x 3mm dovetailed or welded for fixing wire mesh/glass and with one shop coat of zinc chromate primer in and including cutting holes in brick walls for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1, complete all as specified and shown on Drawing No CEAF/STD-186-2012 Sheets 1/1 and as directed by the Engineer in Charge.
Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; and similar work conforming to Fe-290 Gde-E-165, complete all as specified and directed.
Supply and fixing, stainless steel wire mesh, 0.63 mm nominal dia of wire and average width of aperture 1.40mm and fixed to steel frames with tinned tacks, or galvanized wire staples, or fixed to wooden frames with first class hard wood bead, complete all as specified and directed.
Supply and fixing, stainless steel drapery rod 25mm dia, 3mm wall thickness, any shade, including set of SS brackets, fixed to wall with stainless steel, connected accessaries, rubber packing, finials complete all as specified and as directed.
Dismantling of Brick/PCC tiles or terracing tiles, single layer on roofs, etc compelete all as specified and Directed
Demolition of cement concrete as in roof padding, mud phaska, any thickness and any descrition upto RCC roof slab ,cleaning the surface including flashings and junction of parapers, etc with wire brushes and water to the entire satisfaction of Engineer-in -Charge including removing the debris from the site to a designated point by the civil administration complete all as specified and directed by Engineer-in-Charge.
M&L for cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as padding in roof complete as specified. Note :- Padding concrete shall be laid to maintain the slope with thickness at lower end and at ridge as directed by Engineer in Charge. Contractor shall provide leveling bench mark at ridge level and up to edges with distances as specified by Engineer-in-Charge.
M&L for removing the existing water proofing treatment by grinding, picking, sweeping/ cleaning the surfaces thoroughly removing all loose particles, washing down with water to remove dust, applying WB primer as recommended by the manufacturer and applying polyurethane (PU) water proofing coating over the priming coat and further providing 150 gsm polypropylene/Polyster nonwoven geotextile fabric complete all as specified and as directed. This liquid-applied waterproofing membrane must be a two-component, solvent-free, pitch-free, elastomeric polyurethane System. Specifically designed to form a continuous, seamless, water and vapor-proof barrier on concrete / wall surfaces. The cured membrane must demonstrate an elongation of not less than 600 % and a tensile strength exceeding 6 N/mm2 . It must be capable of bridging substrate cracks up to 3.7mm and must possess root resistance. Application requires proper surface preparation, ensuring the substrate is clean, sound, and dry. The two components must be mixed in a 1:1 ratio with a slow-speed drill for 3-4 minutes and used within 30 minutes. The membrane must be applied to achieve a minimum thickness as specified by the manufacturer and authorised applicator suitable for 10 years of brand warrantee. Pretreatment of shrinkage cracks and angle bends is mandatory. The final membrane must be flood tested for 24 hours prior to being protected from UV light within 14 days by a protective screed etc. must be able to withstand service temperatures from – 35 C to +80 C and provide excellent adhesion to concrete without lateral water migration. Note :- (i) Polyurethane water proofing coating shall be extended 300 mm to the parapets and crumple joints including junction of roof and parapet. (ii) While doing the treatment on existing roof, concrete should be throughly inspected for any significant distress, such distress if any shall be repaired/rehabilitated and treated. (iii) The work of water proofing to roof and sunken portions shall be executed by the manufacturer's authorized trained/skilled applicator as per technical guidelines and application methodology of the manufacturer. A MOU is to be executed between the contractor and manufacturer and the same will be got approved from the GE/AGE (I) before commencment of work. The Contractor will arrange to provide company back guarantee for the water proofing work for the period specified here-in-after.
M&L for 40 mm thick brick tiles laid over cement screed 15 mm in cement morter 1:4 in required slope, filling the joints of tiles with polymer based joint mortar (nito tile grout) or equivalent complete all as specified and as directed.
Supply only water proofing compound ISI marked for plastering complete all as specified. Make: Pidiproof WL (Dr Fixit) or equivalent ISI marked make as specified here-in-after and as approved by GE.
S&F Vitreous China wash down water closet with plastic seat cover (pedestal pattern), white (excluding fixing bolts flushing cistern and flush pipe) including 100mm certrifugal cast iron (Spun) 'P' & 'S' trap and 100mm centrifugal cast iron (spun) sanitary connection socket to fit WC outlet including connection to trap, to flushing pipe, anti-syphonage pipe etc. fixed in repair complete all as specified and directed.
S&F Vitreous China squating pan, 'Orissa' pattern, size 580x440mm white, with integral foot rests, including 100mm certifugal cast iron (Spun) 'P' or 'S' trap and 100mm centrifugal cast iron (spun) sanitary connection socket to fit WC outlet including connection to trap, to flushing pipe, anti-syphonage pipe etc. fixed in repair complete all as specified and directed.
S&F Health faucet (ABS Body) stainless steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position fixed in repair complete all as specified and directed.
S & F 10 litres capacity, PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and suitable flush pipe PVC 32mm dia complete all as specified and directed.
S&F for PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.
S & F angle cock cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 15 mm bore iron pipe or for brass ferrule complete all as specified.
S&F bib cock long body with flange, cast copper alloy, chromium plated, fancy type, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule fixed in repairs, complete all as specified.
S&F 2-Way Bib Cock Double Handle with Wall Flange cast copper alloy, chromium plated, fancy type, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule and fixed in repairs, complete all as specified. Make - Prayag Cat No. 6512 or equivalent Cat Part of Makes specified here-in-after.
S&F Bib Cock Nozzle with Wall Flange suitable for washing machine with flange, cast copper alloy, chromium plated, fancy type, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule and fixed in repairs, complete all as specified. Make - Prayag Cat No. P6805 or equivalent Cat Part of Makes specified here-in-after.
S&F Brass CP central hole wash basin mixer with 450mm braided connection pipe (without pop-up) for mixing hot & cold water for 15mm bore iron pipe and fixed in repair, complete all as specified and directed by Engineer-in-Charge. Make- Prayag Cat Part-9350N or equivalent Cat Part of Makes specified here-in-after.
S&F Wall mixer with L bend (provision for over head shower), cast copper alloy, chromium plated for mixing hot and cold water, screwed down for 15mm bore iron pipe, complete all as specified and directed. Make- Prayag Cat Part-7375N or equivalent Cat Part of Makes specified here-in-after.
S&F Brass CP wall sink mixer swan neck counter top for mixing hot & cold water for 15mm bore iron pipe and fixed as in repair, complete all as specified and directed by Engineer-in-Charge. Make- Prayag Cat Part No-9355-N or equivalent Cat Part of Makes specified here-in-after.
S & F 15mm dia tubes medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors complete including taking down old unseviceable all as specified and directed.
S&F steel water tubes, 20 mm bore medium grade, galvanized with all fittings and fixed complete to walls, ceiling or laid in floors, including taking down old unseviceable complete all as specified.
Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.
M&L rotational moulded PVC, triple layered, white colour water storage tanks of capacity 500 litre (cylindrical vertical with closed theard pettern top cover), ISI Marked, hoisted and fixed in position, with & including all fittings such as GI tank nipple etc, including all valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, ISI marked (Minimum weight 210 gms), screwed & suitable for iron pipe 20 mm bore and dismantling unserviceable PVC water tank complete all as specified and directed.
S&F 20mm bore dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repairs complete all as specified and as directed.
S&F wash basins, vitreous china, white, rectangular type of size 550x400mm including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia waste (PTMT Coupling) fittings, brass, chromium plated with long screwed shanks and fly nuts, over and including new brackets fixed in repairs complete all as specified and directed.
S & F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes coupling; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm® 18278 fixed in repairs complete all as specified and directed by Engineer-in-Charge. (Make: Prayag/Nirali)
S&F Wall Mount Modern Kitchen Utensils Dish Rack Stainless Steel (775mmX750mmX250 mm) or nearest larger size in all three dimensions complete as approved by Engr in charge Make- Prayrag Cat Part No- PSP-5 or equivalent model of makes specified here in after.
S&F in repair PVC waste pipe flexible for Sink/ WHB of 32mm size complete all as specified and directed.
S&F Corner glass shelf of radius 300 mm including 02 Nos. metallic holding brackets, railing etc. fixed with PVC rawl plugs and wooden screws, fixed in repairs as approved by GE/Engineer in Charge, complete all as specified and directed.
S&F Rectangular Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed with PVC rawl plugs and wooden screws as fixed in repairs as approved by GE/Engineer in Charge, complete all as specified and directed.
S&F soap dish brass, chromium plated fancy type of standard size and specification as directed and fixed to plugs with chromium plated brass screws.
S&F Brass chromium plated shower rose 125mm with shower arm 15mm size, 195mm long with bend of 45 degree with flange including fixing to steel pipe or union fixed in repairs complete all as specified and directed.
S&F concealed stop cock regular body with flange, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, screwed for 15mm bore iron pipe or for unions & fixed in repairs complete all as specified and directed.
S&F towel rail 600 mm long, 20 mm dia, ‘D’ type, brass chromium plated, fixed to walls with screws and plastic cleats fixed in repairs, complete all as specified and directed. Make-Prayag SS Towel Rail Cubix Cat No. CPA-46
S&F chromium plated grating doom 125mm dia with or without hole fixed in repairs complete all as specified and directed.
S&F 110 mm bore PVC (SWR) pipes of pressure rating 6 kgf/cm2 with, single socketed in any length with rubber ring joints fixed to wall including holding holder /clamps and making good the mouth of rain water pipe including taking down as directed complete all as specified.
S&F 100mm bore PVC (SWR) Bends (any radius), diminishing pieces or tapers (larger bore measured) ISI marked fixed in repairs, complete all as specified and directed by Engineer-in- Charge.
S&F 100 mm bore cast iron floor trap, alongwith SS grating, including jointing with solvent cement any position fixed using cement concrete type B-1 (1:2:4) as per site requirement complete all as specified.
S&F 75 mm bore cast iron floor trap, alongwith SS grating, including jointing with solvent cement any position fixed using cement concrete type B-1 (1:2:4) as per site requirement complete all as specified.
S&F 100mm dia Cast iron soil, waste and vent spun pipes in any length with or without ears, with cement joints, laid in trenches or in wall including neccesary fiiting arrangement and including taking down etc complete all specifie
S&F in repair Cast iron bends 100mm dia bore, single (equal or unequal), diminishing pieces or tapper (large bore measured), complete all as specified and directed by Engineer-in- Charge.
S&F in repair Cast iron branch pieces 100mm dia bore, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, reducer complete all as specified and directed by Engineer-in- Charge.
S&F 75mm dia Cast iron soil, waste and vent spun pipes in any length with or without ears, with cement joints, laid in trenches or in wall including neccesary fiiting arrangement and including taking down etc complete all specified
S&F Cast iron bends 75mm dia bore, single (equal or unequal), diminishing pieces or tapper (large bore measured) fixed in repairs, complete all as specified and directed by Engineer-in- Charge.
S&F Cast iron branch pieces 75mm dia bore, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, reducer fixed in repairs complete all as specified and directed by Engineer-in- Charge.
S&F 75 mm bore cast iron spun vent cowl, fixed with solvent cement in any position as per site requirement complete all as specified.
Uprooting completely tree/ plants (upto 30 cm girth) from wall or any part of building upto 10Mtr or (G+2) story buildings, making good disturbed portion and filling holes in cement mortar (1:3) & PCC (1:2:4) to match with the existing surfaces, complete all as specified and directed.
Demolition of lime concrete/ cement concrete/ brick bats from sunken portion (above ground level), including removing debris away from site to a designated point by local administration or a distance upto 1.5 KM from site.complete all as specified and directed.
M&L for water proofing treatment to sunken portions by clearing the sunken/lowered portion of RCC slab surface for full depth of sunken portion, chieseling out the sticked mortar and applying FOSROC Nitoproof 600 PF (minimum 0.8 mm dft) over a priming coat of Nitoproof WB Primer or equivalent product of makes specified here-in-after and applied to bottom and full vrtical sides as per manufacturer's instructions. Note:- (a) All pipes passing through walls of sunken floor shall be laid before water proofing treatment is carried out. One No. 50mm dia, 35cm long medium grade GI pipe with wire gauge on inside mouth shall be provided to each sunken protion. (b) The sunken portion will be filled with water for dampness and seepage check. In case the slight indication of seepage/leakage is noticed, the same shall be rectified by injectting / grouting to seal all cracks with application of Plymer modified mortar FOSROC nitobond SBR or equivalent product of makes specified here-in-after with integral WPC or cementitious crysatlline waterproofing compound in the affecrted raea to seal all cracks and micro cracks at his own cost and nothing extra will be admissible on thgis ground. (c) An additonal coat of FOSROC Nitoproof 600PF or equivalent product of makes specified here-in-after shall be applied to all junction points of side walls where CI/GI pipes are passing and the same will be seeled with epoxy cement mortar.
M&L cement concrete (1:2:4) type B0 (Using 12.5mm graded aggregate) as in sunken portion or similar items as in filling complete all as specified and directed.
M & L for Broken brick or boulders aggregate not exc 63mm deposited spread and levelled in layers not exc 15mm thick watered and rammed to a true surface in sunken portion, etc complete all as specified and directed.
S&F Steel water tubes, 50 mm bore of length not less than 600mm, medium grade, galvanized, as in spout for sunken floor, fixed in wall, inside end fixed with wire netting and external bent at 45 degree, complete all as specified and directed by Engineer - in -Charge.
M&L preparation of new plastered surfaces of walls and apply two coat of oil acrylic distemper over a coat of primer incl wall care putty of interior grade upto 1mm thick wall care putty to smoothening the surface by using sand paper, complete all as specified and directed.
Material and Labour for preparation of new plaster or untreated plaster surfaces and applying two coats of wall putty with silicon additives (Waterproof putty), sanding with mechanical wall sander having mechanical vacuum mechanism using variable grit sanding papers of required numbers to make surfaces super smooth,making the surface free from dust or loose particles by skilled labour and applying one coat of Smart care Damp prime exterior primer on walls and Chajjas and then applying two coats of modified acrylic smooth emulsion exterior grade with silicon having anti-algai and dust pickup resistance properties, (Nano technology) complete all as specified.
Material and Labour for complete removal of existing treatment /finishes, preparation of old plastered surfaces and applying two coats of wall putty with silicon additives (Waterproof putty), sanding with mechanical wall sander having mechanical vacuum mechanism using variable grit sanding papers of required numbers to make surfaces super smooth,making the surface free from dust or loose particles by skilled labour and applying one coat of interior primer on walls and ceilings and then applying two coats of modified acrylic water based distemper complete all as specified.
Material and Labour for complete removal of existing treatment /finishes, preparation of old plastered surfaces and applying two coats of wall putty with silicon additives (Waterproof putty), sanding with mechanical wall sander having mechanical vacuum mechanism using variable grit sanding papers of required numbers to make surfaces super smooth,making the surface free from dust or loose particles by skilled labour and applying one coat of Smart care Damp prime exterior primer on walls and Chajjas and then applying two coats of modified acrylic smooth emulsion exterior grade with silicon having anti-algai and dust pickup resistance properties, (Nano technology) complete all as specified. Note for item no. 110 to 112:- The Work shall be executed by authorized rep of the manufacturer using fully automatic air less spray machine having flow speed of minimum 1ltr per minute and pressure of 3300 PSI
M&L for preparation of old treated surfaces of ceiling by brooming , steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salts , trading oil , greasy spots and applying two coats of white wash complete all as specified and directed.
M&L for preparation of new or previously untreated wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified.
M&L for preparation of old painted wooden surfaces over 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint, complete all as specified and directed.
M&L for preparation of new surfaces of steel and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.
M&L for preparation of old painted surfaces of steel of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.
Demotion cement Concrete (Reinforced) of any description and in any position not otherwise specifically provided any thickness and any length etc
M&L for 1:11/5:3 (20mm garded aggregate) Type A1 Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like.
Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick
Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cmwide
M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc. all as specified and as directed.
Removing vegetation of any type form chajjas, balcony, mummty slab or from any exposed part of building including making good the damaged surfaces with 40 mm thick (average) PCC 1:2:4 (20mm graded stone aggregate) and applying Fosroc brush bond roof guard minimum 3 layers or fully compatible product of makes specified here in after including scaffolding to required height of building / workplace complete all as specified and directed by Engineer-in-Charge.
Taking down carefully of point wiring (Light, fan, socket or power complete) fittings such as switches, Ceiling roses, regulator, sockets etc to be measured separately) removing from site of work and making good to the disturbed surfaces of walls/floors etc all as specified & directed .
Taking down carefully DB box including MCB SP/SPN of any sizes & capacity all as specified & directed .
All per description of Srl item No. 126 here-in-before,One 3-pin socket outlet 5 Amp on independent board complete all as specified and directed.
All per description of Srl item No. 126 here-in-before, One 3 pin socket outlet 5 Amp on same board complete all as specified and directed.
All per description of Srl item No. 126 here-in-before, One lightl point controlled by 2, two switches complete all as specified and directed.
All per description of Srl item No. 126 here-in-before, One bell point controlled by one switch complete all as specified and directed.
All per description of Srl item No. 126 here-in-before, but with 2.5 sqmm PVC insulated stranded copper conductor FRLSH cable complete with same size of continuous earth wire connected to common earth dolly complete all as specified for One 3 pin socket outlet 15 Amp on independent board.
Sub main wiring of following sizes (Nominal area), two single core PVC insulated unsheathed stranded copper conductor FRLS cable by drawing into existing surface/ concealed, PVC/rigid steel conduits including 06 Sqmm PVC insulated stranded copper conductor FRLS cable 6Sqmm as continuous earth wire conductor connected to common earth dolly and metal part/main switch all as specified & directed. Note:- 2 runs of 6 Sqmm main cable +1 run of 6Sqmm earth cable considered as 1 Running Metre.
Sub main wiring of following sizes (Nominal area), two single core PVC insulated unsheathed stranded copper conductor FRLS cable by drawing into existing surface/ concealed, PVC/rigid steel conduits including 04 Sqmm PVC insulated stranded copper conductor FRLS cable 4Sqmm as continuous earth wire conductor for AC point connected to common earth dolly and metal part/main switch all as specified & directed. Note:- 2 runs of 4 Sqmm main cable +1 run of 4Sqmm earth cable considered as 1 Running Metre.
S&F Switch Modular type single pole one way 6 Amp complete all as specified & directed.
S&F Switch Modular type single pole one way 16 Amp complete all as specified & directed.
S&F Switch Modular type single pole two way 6 Amp complete all as specified & directed.
S&F Switch Modular bell push type single pole one way complete all as specified & directed.
S&F Socket outlet Modular type single pole multi purpose 6 Amp complete all as specified & directed.
S&F Socket outlet Modular 3 pin 6/16 Amp multipurpose, 240 volt complete all as specified & directed.
S&F 2 modular type regulator for ceiling fan of any sweep complete all as specified and directed.
S&F Ceiling rose surface Bakelite 65 x 50 mm two to three terminals complete all as specified and directed.
Taking down the geyser and refixing back on the same location and connecting complete all as specified and directed.
S&F Bell Ding Dong AC 230 volt single pole Complete all as specified and directed.
S&F MCB single pole and neutral 240 volt 40 to 63 Amp including connection Complete all as specified and directed.
S&F MCB SP 240 volt 6 to 40 amp including connection Complete all as specified and directed.
S&F sheet metal enclosure single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified.
S&F sheet steel enclosure double door for DB SPN 240 volts 12 way with 200 Amps rated bus bar complete all as specified.
Supply and fixing LED light fitting 1x9W/1x10W bulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed .
Supply and fixing LED light fitting 4 feet, 18W, 220V, AC, decorative box type with driver, holder including LED tube light up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed .
Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220V AC decorative type with driver holder and LED lamp including connecting up with three core flexible wire complete all as specified and as directed
Supply and fixing wall mounted fittings with ABS housing and clear polycarbonate cover including retrofit LED bulb 7/9 watt and provision of flexible copper 3core cable 0.5Sqmm from connector/ ceiling rose to fitting and conforming to City-1/ City -2 all as specified and directed
Refixing light fitting any type/ capacity all as specified and directed (LED tube light 4 feet, 2 feet Bulkhead and wall light).
M & L for earthing complete with galvanised steel earth plate electrode 60cm×60cm× 6mm thick, buried directly in ground, vertically to a depth not less than 2.25 metres deep below ground level with top edge of the earth plate at depth not less'than 1.5 metres below ground level earth plate surrounded by 15cm thick and packed layers of charcoal, dust and common salt, earth lead GI wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron and thimbles and earth wire protected by galvanized iron pipe light grade 15mm bore and water pipe 20mm bore GI medium grade with funnel and wire mesh complete including excavation and earth work, PCC chamber and cover in cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate in lieu of CI cover and frame etc all as specified and shown in electrical plate No 5 of SSR-2009 (Part-I).
S&F Modular Metal Flush Box 1/2 module complete all as specified & directed.
S&F Modular Metal Flush Box 3 module complete all as specified & directed.
S&F Modular Metal Flush Box 6 module complete all as specified & directed.
S&F Modular Metal Flush Box 8 module complete all as specified & directed.
S&F Modular White Cover Plate With Frame 2 module complete all as specified & directed.
S&F Modular White Cover Plate With Frame 3 module complete all as specified & directed.
S&F Modular White Cover Plate With Frame 6 module complete all as specified & directed.
S&F Modular White Cover Plate With Frame 8 module complete all as specified & directed.
S&F Modular White Cover Blanking Plate 1 complete all as specified & directed.
Taking down carefully ceiling fan, exhaust fan, sealing cable end, dismantling blades and removing fans and blades to store complete all as specified and directed.
Rewinding of ceiling fan 1200/1400mm sweep and exhaust fan 300mm sweep with super enameled copper wire of appropriate gauge incl replacement of insulating materials such as laminated lethroid paper, sleeves, necessary varnishing with golden colour varnish, greasing/oiling of bush and the bearings, replacement of missing/worn out nuts, bolts & washers etc and testing after reassembling and refixing back on the same location and connecting complete all as specified and directed. (taken down vide item No 165)
Spray painting with synthetic enamelled paint of approved colour (AS approved GE) after preparation/making of old surface suitable for painting of ceiling fan, exhaust fan of any sweep/Make/Model complete all as specified and directed.
Hanging only Ceiling fan and connecting up including provision of flexible cable from ceiling rose or connector to fan omplete all as specified and directed.
Hanging only Exhaust fan and connecting up including provision of flexible cable from ceiling rose or connector to fan omplete all as specified and directed.
Note: The Total amount shall subject to adjustment of credit of Rs. 175265.00 for old Materials as per Schedule of Credit.
B N FRIENDS AND CO (BID ID -3495981)
M/S MANI GARG CONTRACTOR (BID ID -3495830)
Baba Engineers and Contractors (BID ID -3496154)
M/s R. Krishan and Co. (BID ID -3496221)
M/S MATLOOB AHMED (BID ID -3494946)
Anil Kumar Gupta (BID ID -3496390)
Jawandha Enterprises (BID ID -3502884)
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.54 MB
BOQ_827232.xls
BOQ • 1.14 MB
TenderDocumentsT17202526.pdf
Tender Documents • 1.43 MB
Download all tender documents and submit your bid