CERTAIN ADDITION, ALTERATION WORKS, PROVISION OF AUDIOLOGY BOOTH AND RO PLANT AT AIIMS BIBINAGAR

Amount

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry

Providing and fixing Ist quality ceramic glazed wall tiles of size 300 X 450 mm conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in any colour as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sq m, including pointing in white cement mixed with pigment of matching shade complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Removing And refixing in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). as per directed by Engineering incharge

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (PartI) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Removing And refixing the Flush door Shutter for toilet Doors as Per directed by Engineering incharge

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing aluminium sliding door bolts size of 300 X 16 mm, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete.

Providing and fixing aluminium tower bolts, size of 250 x 10 mm ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc.complete.

Providing and fixing aluminium handles, size of 125 mm, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc.complete

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm.

12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) While doing the Plastering, the entire floor needs to be properly covered, so that Plastering does not spoil the floor. Also immediately after plastering floors needs to be cleaned properly. Any damage to the floor due to plastering needs to be rectified by the contractor at his own cost. No Extra to be paid for the same.

White washing with lime to give an even shade : New work (three or more coats) While doing the Painting, the entire floor needs to be properly covered, so that Painting does not spoil the floor. Also immediately after painting floors needs to be cleaned properly.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer. While doing the Painting, the entire floor needs to be properly covered, so that Painting does not spoil the floor. Also immediately after painting floors needs to be cleaned properly.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work. While doing the Painting, the entire floor needs to be properly covered, so that Painting does not spoil the floor. Also immediately after painting floors needs to be cleaned properly.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work While doing the Painting, the entire floor needs to be properly covered, so that Painting does not spoil the floor. Also immediately after painting floors needs to be cleaned properly.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. While doing the Painting, the entire floor needs to be properly covered, so that Painting does not spoil the floor. Also immediately after painting floors needs to be cleaned properly.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. While doing the Painting, the entire floor needs to be properly covered, so that Painting does not spoil the floor. Also immediately after painting floors needs to be cleaned properly.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Any damage to the floor due to demolish/dismantling work needs to be rectified by the contractor at his own cost. No Extra to be paid for the same.

Demolishing brick/solid block work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar Any damage to the floor due to demolish work needs to be rectified by the contractor at his own cost. No Extra to be paid for the same.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm. Any damage to the floor due to demolish/dismantling work needs to be rectified by the contractor at his own cost. No Extra to be paid for the same.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer in-charge. (Glazing, paneling and to be paid for separately) :

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10 kg/ sqm).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in- charge.(Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm).

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in charge. (Only weight of grill to be measured for payment).

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Filling With Cinder in Sunken Slabs in : 1:3 Ratio ( 1 cement : 3 Cinder ) etc complete.

Providing and sticking Glass film to existing glass for Aluminium Door Shutter glasses of any size & thicknes Including supplying and fixing charges .(As per Engineer Incharge.

Providing and fixing of 100 mm aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc.complete :

Providing and fixing Brass 100mm mortice latch and lock with 4 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing of 255 X 19 mm stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete.

Providing and fixing window side push locks for aluminium sliding Window shutters with necessary screws etc.complete :

PLUMBING WORKS:

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/ make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe 40 mm dia.

Bottle trap 38/40 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm Vide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms

Providing and fixing 20 mm outer dia Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Make: Supreme, Finolex, Astral Concealed work including cutting chases and making good the walls etc.

Providing and fixing of 450 mm length 15 mm nominal boreuplasticised PVC connection pipe with brass unions.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15 mm nominal bore.

Providing and fixing SS grating with rim including setting in floor with white cement mortar and making good the floor. 125mm dia

Providing and fixing of overhead shower 120mm dia single flow (ABS body Chrome plated with gray pace plate) with shower arm 190mm and flange including all fittings etc. complete conforming to I.S Specification of approved make as per directions including all lead and lift etc., complete.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements. Weighing not less than 106 gms.

Supplying and fixing CP Health Faucet superior quality including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in- Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in- Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2

Providing and fixing PVC floor trap self cleansing design with or without vent arm complete including cutting and making good the walls and floors.110mm dia inlet 110mm dia outlet.

Checking plumbing lines, Repairing blocked inlets and outlets connections for vertical pipe lines (CPVC & UPVC) for Ground,First And Second Floors. (As per Engineer Incharge)

Core Cutting or making holes to slab and beams for pipe connections from 1st floor to cellular and Spout Pipes (UPVC). (As per Engineer Incharge)

Providing and fixing C.P. brass long body 2way Bib Cock of approved quality conforming to IS standards and weighing not less than 690 gms.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in- Charge. Concealed work, including cutting chases and making good the wall etc.

160mm Dia PVC Pipe

40mm Dia PVC Pipe

Providing and fixing of 25 mm nominal outer dia Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Make: Supreme, Finolex, Astral Concealed work including cutting chases and making good the walls etc.

WIRING:

Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch, modular plate, suitable GI / PVC box and earthing the point with 1.5 sqmm, FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for circuit / submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required.

2 x 1.5 sq.mm + 1x1.5 sq.mm earth wire

2 x 2.5 sq.mm + 1x 2.5 sq.mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

3 core x 1.5 sq.mm

3 core x 2.5 sq.mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing suitable size GI / PVC box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI / PVC box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supply and fixing 3 pin, 6A ceiling rose on the existing junction box / wooden block including connection etc as required.

Installation, testing and commissioning of ceiling fan including wiring the down rod of standard length (upto 30 cm.) with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Supply and Installation of 230 V A.C Heavy Duty exhaust fan min 250mm - 450mm sweep in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.(make:Havells,Usha,Bajaj,Crompton)

Wiring for group controlled (looped) light point / fan point / exhaust fan point / call bell point (without independent switch etc) with 1.5 sqmm FRLS PVC insultated copper conductor single core cable in surface / recessed PVC conduit, and earthing the point with 1.5 sqmm FRLS PVC insultated copper conductor single core cable etc as required.

Supplying and fixing following of 4 way Double door horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess complete with tinned copper busbar, neutral busbar, earth bar, din bar, interconnection, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator).

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Triple pole and neutral

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing 63 amps rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 63 amps rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Providing and fixing 4 mm dia copper wire on surface or in recess for loop earthing.

Laying and fixing of one number upto 35 sq. mm (clamped with 1mm thick saddle) PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Laying and fixing of one number Upto 35 sq. mm (clamped with 1mm thick saddle) PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Supplying and making end termination with brass compression gland and aluminium lugs for size of 4 Core x 16 sqmm PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Supply of the 4C x 16 sqmm size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date.

Supply & installation of surface or wall mounted LED batten with polycarbonate housing & integrated electronic driver, high translucent diffuser, 20 - 24 W LED light fixture (4 feet), p.f ≥ 0.9, THD < 20%, 2kV surge protection, CCT≥ 5700K, Efficacy ≥ 100 Lm/W, CRI ≥ 70 etc with all required accessories. (Wipro LL20-221-XXX-65NE3 / Crompton LDL 20-WW/Havells LUMILINE BS20W LED865S PCWH).

Supply & installation of surface mounted downlight fixture, die cast aluminium housing, high translucent diffuser, 15 - 18W LED light fixture, p.f ≥ 0.9, THD < 20%, 2kV surge protection, CCT≥ 5700K, Efficacy ≥ 100 Lm/W, CRI ≥ 70 etc with all required accessories.(Havells INTEGRA NEO SURFACE DLS15WLED857S /Crompton LCDSPLN-R-18-CDL/ Wipro Iris slim LD80-131-XXX-60-SM).

Supply & installation of surface mounted downlight, die cast aluminium housing, high translucent diffuser, 5 - 10 W LED round light fixture, 2kV surge protection, CCT ≥ 5700K, Efficacy ≥ 100 Lm/W, CRI ≥ 70 etc with all required accessories. (Crompton LCDSPLN-R-06-CDL / Wipro LD80-350-XXX-60-SM / Havells INTEGRA NEO SURFACE DLS10WLED857S

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.(Havells efficiencia neo,Crompton energion/Bajaj efficio). The rate shall include suitable size anchor fastner and hook to mount the ceiling fan in the existing RCC slab.

Fan Hook (8mm & Double anchor Fastener / D-Type)

Audiology Booth : Heading

Supply ,Fixing and Installation of DOUBLE ROOM SUITE Audiology Booth. The booth shall have an inside Aluminum (1100AW aluminum grade series) Frame covered by termite resistant plywood on both sides and perforated sound proof boards with outer finishing of mica.The inside of the cubicle will have acoustic treatment on wall and ceiling and sound absorbent flooring, There will be one sound treated door for the main entry which will be of 750mm (W), and inside sound proof door for next room – both sound treated.The wall of the chamber will be cavity walls filled with Sound insulation material (Glass wool/any sound proof material to achive desire level of sound proofing),excellent corrosion resistance and workability.High thermal and electrical conductivity low strength. Equipment connections to be provided including patch panel and audio sockets at desired points, electrical points as required and as directed by engineer in charge including necessary wiring with FRLS PVC Iinsulated copper conductors of approved make and necessary earthing and connection to nearest input point, MCCB, DB etc complete and adeqate lighting with LED lights to have minimum intensity of 50,000Lux at floor level inside the booth. All testing, consultancy, Acoustical corrections, including warranty of Acoustical material for three year, including all labour, material and transportation. etc. complete as described in detailed technical specifications and as directed by Engineer in charge. The dimensions of the booth shall be as follows: Inner size of tester room: 10 feet x 6 feet x 8 feet Inner size of Patient room: 10 feet x 12 feet x 8 feet External dimensions of the Booth: 20 feet x 12 feet Fixed observation glass: 4 feet x 4 feet between two rooms 30dB attenuation.

Supply installation testing and commissioning 1.5 Ton, Inverter type 5 Star Rating of BEE Air Cooled Split Type Air Conditioners complete with indoor unit (IDU), Outdoor unit (ODU), surface / concealed coper Refrigerant piping with insulation (EP Foam pipe section) . (IDU to ODU) copper power cable (at least 3CX 2.5 Sqmm, PVC Insulation, FRLS copper wire). (IDU to ODU), R-22/R-410 Refrigerant , PVC drain pipe (dia 15mm) Remote,ODU stand, suitable for 400/230V +10% of 50 Hz, 1/3 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with scroll/ reciprocating/ rotary compressor. (Make:Voltas,Blue Star,Llyod,Hitachi,Carrier)

Furniture: Supply and installation of furniture as given below for tester room and patient's room complete as described in detailed technical specifications and as directed and approved by Engineer in charge. The furniture shall be provided as per the specifications and drawings specified in the tender documents. The final product needs to meet the requirements of the institute. Any variation in the specifications/drawings, the decision of the Engineer in charge shall be final and binding. Nothing extra shall be paid for the same.

Table: Table of the size 1200 X 750 X 760 mm (H) table made up of 20 mm pre laminated particle board. The table shall have one drawer unit consist of three box drawers with 16 mm pre laminated particle board. Two drawer units shall be of overall size 350 X 400 X 80 mm. Bottom Drawer unit 350 X 400 X 240 mm. Approximate 12 mm gap between each drawer. Suitable size channels shall be provided throughout the depth of the drawer. Drawers shall have multipurpose steel lock. All three drawer handles are chrome plated handles.

Doctor Chair: Doctor unit pneumatic hand operated,5 castor wheels, Height of the seat can be adjusted via foot pedal with height adjustable seat 510-710 mm (max - Min). Steel structure made up of chrome plated steel parts and highly posolished aluminium cross based with foot ring. Back rest is rotatable 180 degrees with height adjustment mechanism.Overall weight 14 kgs aproxmately. As per drawing attached.

Patient Chair (visitor Chair): Chair Revolving Type-II (low back and push back with castors) The seat and back shall made up of 12 mm thick hot pressed upholstered with fabric and moulded polyurethane foam, together with moulded ABS seat and back covers.The back form shall be designed with contoured lumbar support for extra comfort. Seat: 510 mm width X 470 mm Depth x 60 mm thick Low back:450mm Width X 430 mm height 60 mm Thick. Arm rest The arm rest made of a black inetegral polyurithanae with 75-85shore "A" hardness and reinforced with M.S insert.

Free Field Speaker table Overall size 450 x 450 x 760 mm frame made of 25 mm Square Tube 1.6 mm thick with powder coated as per sketch. Top is size of 450 x 450 mm made up of pre laminated particle board duly PVC edging all round all as per commercial Practice.

Reclining Chair (Chair Examination) Electrically operated examination and Treatment chair with electrical/hydraulic height adjustment chair with foot switch/remote control. The upper part is easily all round swiveling and flexible by an arresting brake. The tall back rest is adjustable forward beyond the vertical line backwards. It can be declined slightly more than the horizontal line without any special assistance. By the synchronous coupling of the backrest to the foot- support the chair can be quickly changed into a long and solid couch. The arm rests, made of resistant polyurethane, can each separately be swivelled off backwards all as per commercial practice and as per drawing attached. TECHNICAL DATA Weight:120 Kgs (Aprox) Height: 750 mm Depth: 420mm Height of the seat: 520-720mm (min-max) Power supply: Operated on 220v/50hz. Overall Sleeping Position Length: 1820mm Floor Space: 875 x 600 mm

RO Water Treatment plant and Shed:

Supply and Installation of Galvalume sheet covered shed with steel structure to cover the complete area of RO Plant including necessary fabrication, bolting, welding, fixing painting etc including PCC for fixing on to floor/ground complete all as directed by the Engineer-in-Charge.

Supply and Installation of glavanised iron Chain link fencing around the RO plant including fixing, bolting, welding, necessary steel structure etc. complete as directed by Engineer in Charge.

Supply, Installation, Testing and commissioning of 1000 Liters Per Hour capacity Automatic RO Water treatment plant with all necessary fittings and accessories including 1000 liters capacity Stainless Steel Water tank with stainles steel lid made from SS 304 food-grade quality placed on a iron stand of height 150 mm square in shape made up of squre/circular pipes with stainless steel sheet welded on top and having sufficient strength to with stand 1000 liter stainless steel tank when full. Dimensions of stand shall be such that it will extend 150 mm beyond tank on all sides when the tank is placed on the stand at centre, all electrical fittings with necessary wiring, switch,MCCB socket and DB, Raw water Pump,Multi grade filter Unit,Activated carbon filter,antiscalant doser,micron filter,High pressure pump,RO membranes,RO Housing,RO cleaning/ fungus removal system,Flushing Pump,Electrical Panel including voltmeter, MCB, Indicating Lights, ON/OFF Button,Rocker Switch Complete Starter,over load relay, single phase preventor for pump,incomer, auto manual switch, Rotameter, Low pressure Switch, Highpressure Switch, Pressure Gauges, Pressure Switch,SS Frame/Stand for control panel including all necessary fittings and fixtures including provision of necessary base with PCC/RCC etc and connection to existing water tank for inlet water, complete all necessary to commion the RO plant and to be installed on the roof top of the building/any other location as directed by the Engineer-in-Charge.

VIJAYA REFRIGERATION N ELECTRICALS