Special Improvement works to zonal office building in ward no. 55

Amount

Picking the existing cement plaster surface the chipping materials clearing away from the site and clearing etc., complete

Dismantling the existing damaged Brick / stone masonry in Cement mortar walls under 3 m highetc., complete

Plastering with cement mortar (1:5) 20mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc, complete as per standard specifications

Brick work in CM 1:5 (one cement & five sand) using III class country bricks of size 83/4"X41/4"X21/4" including finishing, curing, etc., complete complying with standard specification - 100CFT

Plastering with cement mortar (1:5) 12mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc, complete as per standard specifications

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Manufacturing Supply and Fixing of Retro Reflective Road Name sign board Double arrow big size out if wide angle cuble corner micro prismatic grade sheeting confirming to IRC 67:2010 & type XI standards of ASTM D 4956-09 specifications and fixed over 2mm thick aluminium sheet back support frame of stainless steel supported by 32 NB stainless steel pipe all around and 65 NB pipe vertical post firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 30cmX30cmX45cm complete. The information message shall be made out cut out letters in blue transparant overlay film as per IRC 67-201 Guidelines , 7years pre qualification warrenty for Retro Reflective sheeting from the original sheeting manufacture & a certified copy of three years out door exposure report from an independent test lab for the product offered shall be submitted by the contractor. The sign board shall be Retro Reflective type XI. The Retro Reflective sheeting should have manufactures WATERMARK on the sheeting surface for identification. Double Arrow Big Size 96"X 48"

Supplying and fixing in position of Alu. Anodised Partition with 62x38x2mm extruded box section at bottom vertical and horizontal members. The vertical member are spaced at 90 cm c/c and to horizontal members are spaced at 1.2M, 2.1M and 2.4M height the bottom panels should be covered with 12 mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick glass thick glass with necessary glassing clips.rubber beading, etc., including necessary dismantling holes in RCC columns, beams masonry wherever necessary with power power drill ti the extent required and made good to the original conditions after fixing as directed by the departmental officers. All the Aluminium sections should be anodised to 1.5microns as per ISI

Supplying, fabricating and fixing in position of Alumi.Anod.natural colour matt finish door half glazed and half PLB board using 12 mm thick PLB board and 5.5 mm thick glazed door using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al. Clips, Best double action floor springs, Aluminium Handles on both sides,floor stopper,Tower bolt, Locks and glass including all materials, Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete. The Alumi. surface must be anodised with matt finish under electrically controlled condition in accordance with IS specification 1868 / 1962 of Anodic filthickness of not less than 15 Microns (Fifteen) for all sections.

Supplying and fabrication and fixing in position of anodised natural colour matt finish sliding window in two track in all floors with following sizes. All the three shutters with slinding arrangements, the bottom section should have Gutter arrangements so as to drain the water entering and made with extruded aluminium section for outer frames as shown below with necessary accessories such rubber beading. Aluminium clips, rubber beading,handle and fixing 4mm thick clear sheet glass including all required for fabrication etc., complete.Necessary dismantling making holes in RCC columns, beams, masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by the departmental officers.The Al.Surfaces is to be anodised with matt finish under electrically condition in accordance with ISI 1868/1962 specification for an

Supply and fixing of single box type (Philips / Havells / Eq) suitable for 4 feet 20w LED Tube light with TW round blocks on wall or ceiling with 20w LED tube light with PVC unsheated copper leads from terminals to the fittings

Supply and fixing of 1200mm (48”) sweep AC Ceiling fan (Crompton / Havells / Usha / Equivalent) with 2 module 100W regulator complete 300mm Down rod on existing clamp

Supply and fixing of 450 mm Sweep Wall Mounting Fan etc., complete

Add GST 18%

M GNANAVEL (BID ID -1328973)