REPAIR/ MAINTENANCE OF SEEPAGE, LEAKAGE, ROOF TREATMENT, BROKEN CHAJJAS, PARAPET WALL AND CLEANING OF WATER TANK TO CERTAIN BUILDINGS AT MANEKSHAW MARG IN THE AOR OF AGE B/R-I UNDER GE (EAST) DELHI CANTT-10

M & L for Dismantling of brick tiles (laid flat or on edge) on roof surface laid bedded and pointed in any mortar

M & L for Demolition of mud in roof, any thickness, including plastering and leaping upto six storey bldg incl necessary scaffolding arrangement complete all as specified and directed (whether full thickness removed or only a part there of) and removing from cantonment area or as directed complete all as directed by Engr in charge and specified.

M&L for cement concrete 1:2:4 type B0 (using 12.50 mm graded stone aggregate) as in levelling coarse over RCC slab to bring the desired slope up to six storied Bldg, using water proofing compound as per manufacturer instruction complete all as specified & directed. Note:- Water proofing compound shall be measured and paid separately.

Supply only liquid water proofing compound and mixed as per manufacturer's instructions, complete all as specified and as directed.

M&L for APP based polymeric membrane plain finish minimum weighting 3 kg/Sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) over one coat of 85/25 bitumen @1.2 kg/sqm and paste the membrane with torching method and again apply a coat of 85/25 bitumen @ 1.2 kg/sqm at overlapping joints

S & F for Heat Resistant Terrace ceramic Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface up to 3 cuts complete, including providing skirting up to 150 mm height along the parapet walls in the same manner.

M&L Bitumastic gola, with 80/25 bitumen and coarse sand mixture. 1:3 by weight, 8cmx8cm at the junction of roofing to vertical surfaces

M & L for plain cement concrete 1:2:4 (type B-1 using 20 mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges etc complete all as specified and directed.

Disconnecting existing tanks, setting aside (or lowering of required) for repairs , cleaning, etc. and hoisting if required reconnecting and refixing in position ( cleaning repairing, etc. measured separately ) comple all as specified and directed.

Taking up or down steel tubing 15 mm bore and connection including cleaning for refixing or removal to store complete all as specified and as directed by Engineer-in-Charge

S&F steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 15 mm dia including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete 1:2:4 complete all as specified and as directed by Engineer-in-Charge

Taking up or down steel tubing 20 mm bore and connection including cleaning for refixing or removal to store complete all as specified and as directed by Engineer-in-Charge

S&F steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 20 mm dia including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete 1:2:4 complete all as specified and as directed by Engineer-in-Charge

Taking up or down steel tubing 25 mm bore and connection including cleaning for refixing or removal to store complete all as specified and as directed by Engineer-in-Charge

S&F steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 25 mm dia including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete 1:2:4 complete all as specified and as directed by Engineer-in-Charge

Taking up or down steel tubing 32/40 mm bore and connection including cleaning for refixing or removal to store complete all as specified and as directed by Engineer-in-Charge

S&F steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 32/40 mm dia including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete 1:2:4 complete all as specified and as directed by Engineer-in-Charge

Taking up or down steel tubing 50 mm bore and connection including cleaning for refixing or removal to store complete all as specified and as directed by Engineer-in-Charge

S&F steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 50 mm dia including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete 1:2:4 complete all as specified and as directed by Engineer-in-Charge

S&F in repair 15mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repair 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repair 32/40mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repair 50mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

M & L including T&P for Cleaning of existing RCC water tanks (any type and any capacity) on top of multistoried buildings (G+8 Levels), including emptying the water tank completely(depth of water tank up to 2.00 M), cleaning the internal wall surfaces and bottom surface of tank to remove all disputation/ fungus,other micro-organisms etc. Using light hammer & wire brushes, taking out and removing sediment loose dirt/mud sludge,vegetation and other foreign materials completely from the internal and external surface of tank disposal of all the waste/spoil outside from the MoD land . And washing repeatedly with acid based material, corrosion inhibitors and dispersing agents solution inside surfaces of tank with water and washing with clean water thoroughly and preparation of the surface to receive new plaster complete all specified and directed by Engineer-in-charge.

M & L including T&P for Cleaning of PVC water tanks (500 Ltrs capacity) including on top of multistoried buildings (G+8 Levels), including emptying the water tank completely, cleaning the internal wall surfaces and bottom of tank by scraping with steel wire brushes, removing all dirt and scaling inside the tank and washing clean of all loose debris, complete all as specified and to the entire satisfaction of Engr-in-Charge.

M & L including T&P for Cleaning of PVC water tanks (1000 Ltrs capacity) , including emptying the water tank completely, cleaning the internal wall surfaces and bottom of tank by scraping with steel wire brushes, removing all dirt and scaling inside the tank and washing clean of all loose debris, complete all as specified and to the entire satisfaction of Engr-in-Charge.

Dismantling water tanks exc 250 Ltrs but not exc 500 ltr capacity and removing to store.

S&F rotantional moulded polythylene water storage tanks 500 ltr capacity (cylindrical vertical with closed top ) hoisted and fixed in position complete with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwd for iron pipe 25mm bore complete all as specified and directed.

Dismantling water tanks exc 500 Ltrs but not exc 1000 ltr capacity and removing to store.

S&F rotantional moulded polythylene water storage tanks 1000 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position complete with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwd for iron pipe 25mm bore complete all as specified and directed.

Dismantling water tanks exc 1000 Ltrs but not exc 2000 ltr capacity and removing to store.

S&F rotantional moulded polythylene water storage tanks 2000 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position complete with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwd for iron pipe 25mm bore complete all as specified and directed.

S&F in repair water tank cover complete set of capacity 500 Ltr to 2000 Ltr.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specifed and directed.

M&L for providing RCC 1:1½:3 type A-1 (using 20 mm grade stone aggregate) as in slab supportetd on walls, shelves, Chajjas, cantilevers or similar work complete all as specified and as directed.

M&L for Formwork to Chajjas through and similar items including edges and similar work complete all as specified and as directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

M&L TMT bars 10mm dia and over in reinforcement cut to length bent to shape required incl hooking ends and binding with MS wire (annealed) not less than 0.9mm dia complete all as directed and specified.

Demolition of brick work/stone bulder measonary built in cement mortar or cement lime mortar of any description and in any position all as specified.

M&L for brick work in CM (1:4) straight or curved on plan exc 6.0m mean radius and using old size sub class 'B' bricks all as specified.

Description all as per item No 43 above but except bricks

M&L for Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed

M&L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors etc. complete all as specified and directed.

Providing and laying Super fluid Microconcrete -Roffe crete repairs (or equivalent as specified in the List of Brand names) in beam bottoms, columns, slabs etc. including mixing with 5mm to 10mm size aggregates, waterproof ply wood/ steel plate shuttering, pouring, temping, Consolidating, curing etc complete as per Manufacturer’s specification and Consultants Instructions.The item shall be paid on actual consumption of Micro concrete.

Chipping off existing loose, damaged Concrete from RCC members of all affected RCC Columns, Beams, Slabs and Chajjas on External and internal facades, etc beyond main r/f. (if required in the opinion of the Consultant), carefully with chisel and hammer Providing and applying ‘Rusticide SS’ Rust passivator or equivalent as specified in the Brand Names to existing r/f. bars Including wire brushing of reinforcement , cleaning washing of concrete etc complete as directed.Providing and applying two coats of rust preventor slurry made out of “Polyalk Fixoprime” or equivalent as specified in the Brand Names and cement in proportion 1:1.5 to existing r/f.bars as directed complete. Providing and applying bonding coat of slurry made out of “Polyalk EP” or equivalent as specified in the Brand Names and cement in proportion 1:1 to concrete and r/f substrates complete as directed Providing and applying “Polyalk EP” or equivalent as specified in the Brand Names.Polymer modified cement mortar in Required proportions(1:5:15) to RCC members Including Hand packing, curing and making the surface rough for plastering. Note -:The rates quoted by the tenderers are deemed to be up to G+9 floor bldg included roof , external walls , shafts area and safety precautions , necessary T&P, scaffolding/jullha etc as required. Note:- The rates quoted by the tenderers are deemed to be up to G+9 floor bldg included roof , external walls , shafts area and safety precautions , necessary T&P, scaffolding/jullha etc as required.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Non skid ceramic coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and incl screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM (1:6) complete all as specified

M&L for Non skid ceramic coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exc 0.18 sqm but not exc 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and incl screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM (1:6) complete all as specified

Description all as per item No. 51 above but on vertical surfaces such as skirting / dados, over and including 10 mm thick CM 1:4 as in backing coat complete all as specified.

M&L for Vitrified ceramic tiles ultra charged ( dark shade) 10mm thick (square/rectangular) area of each tile exc 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and incl screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM (1:4) complete all as specified

Description all as per item No. 53 above but on vertical surfaces such as skirting / dados, over and including 10 mm thick CM 1:4 as in backing coat complete all as specified.

M&L for Glazed ceramic coloured tiles in vertical surfaces 600 x 300 / 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match, over and incl 10mm thick CM (1:4) in dado/skirting tiles complete all as specified and directed.

M&L for Renewing tiles in patches, area n exc 5 sq.m. including removing and cleaning old tiles, preparing beds and laying or setting, jointing and pointing new or old tiles complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar.

18 to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking plateforms,dado/wall and like over and incl 15mm thick cement mortar 1:4, including pointing in white cement mortar 1:2 using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed

S&F in repair 15mm angle cock/ stop valves, with wall flange , fancy type chromium plated cast copper alloy, screwed down, high pressure, with fancy handle, screwed ends for iron pipe or for unions for 15mm bore steel tubing complete all as specified & directed.

S & F in repairs 15 mm bore bib tap (long body) ,fancy type chromimum plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions. complete all as specifed and directed.

S & F in repair 15 mm bore two way angle cock with wall flange cast copper alloy, fancy type, chromium plated, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make : Hindware Cat Part No. F740006CP Dove and equivalent in Jaquar/ Hindware and Kohilar as approved by GE

S & F in repair 15 mm bore two way bib cock with wall flange cast copper alloy, fancy type, chromium plated, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make : Jaqaur Cat Part No. ARI-CHR-39041 and equivalent/ Hindware and Kohilar as approved by GE

S&F in repair Brass CP Basin mixer central hole for making hot and cold water fixed as per manufacturers manual with long shunk and cup washers, screwed both ends suitable for 15mm bore GI Pipe joints to GI pipes or unions, complete all as specified and directed. Make : Jaquar Continental CON-CHR-167KNB and as approved by GE

S&Fin repair brass chromium plated wall mixture 2 in 1 system with L- bend provision for over head shower and suitable for 15mm bore GI pipe including three joints to steel pipes or unions and plugging and screwing to walls all as specified and directed. Make : Jaquar Continental CON-CHR-273KNUPR and as approved by GE

S&F in repair 125 mm size Brass chromium plated shower rose suitable for 15 mm bore pipe complete all as specified and directed.

S&F in repairs Hand Shower (Health Faucet) with 8 mm Dia, 1 Meter Long Flexible Tube & Wall Hook completed all as specified Make : Jaquar Cat part No. ALD-CHR-573 and equivalent in jaquar / Hindware/Parryware or equivalent make as per approved make list).)

S & F in repair full pedestal pattern wash hand basin with pedestal , size of basin 58 × 43.5 × 82.5 cm as approved by GE including brakets , chromium plated brass waste coupling etc complete all as specified and as directed. Make : HindwareTango Full Pedestal Wash Basin Cat part No. 10086 and equivalent in jaquar /Parryware or equivalent make as per approved make list)

S&F Vitreous China wash basin, white, flat back, size 550 x 400 mm including , chain and plug but including brackets or erecting stand including & (32 mm -45 gms/40mm-60 gms ) waste coupling of CP complete all as specified and dirtected by Engr-in-Charge .

S & F in repairs Vitreous china floor mounted WC ( Cascade) one piece type (off white) including connecetion in drain etc incl water closet seat cover , flushing cistern, with P or S trap with all fitting and fixture complete all as specified and as directed. (Make : Jaquar / Hindware/Parryware)

S&F in repair Vitreous China squatting pan 'Orissa' pattern size 580 x 440 mm white, with integral foot rests with connection to trap , and to flushing pipe antisyphonage pipe including trap set in and including concrete etc complete including making good to floor all as specified and dirtected by Engr-in-Charge .

S&F in repair 10 Ltrs capacity PVC valveless symphonic action type flushing cistern white low level with inlet, ball valve float handle including bracket including flush pipe of polyethylene of low or high density or PVC 32 mm dia for low level cistern etc complete all as specified and directed

S & F in repair PVC connections 15mm size with PTMT nuts of length 450mm.

S & F in repair PVC connections 15mm size with PTMT nuts of length 600 mm.

S&F in repairs of CP towel rail 600mm long fixed with and including chromium plated brass screws and and wooden/plastic cleats (minimum weight 190 gms) fixed on walls, complete all as specified.

S & F 32/40mm spring type PVC waste pipe fixed toWHB and sink (Note minimum length of each pipe should not be less than 0.80RM), complete all as specified and as directed.

S & F in repairs Sheet glass corner shelf assembly consisting of 5.5mm thick sheet glass Min size 300 mm x 300 mm with chromium plated bracket guard and railing complete all as specified and as directed.

S & F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 45 cm long complete all as specified and as directed.

S & F in repair Towel Ring Round with Round Flange fixed in positon with and including chromium plated brass screws and wooden/plastic cleats, complete all as specified and as directed. Make : Jaquar Cat part No. ACN-CHR-1121BN and equivalent in jaquar / Hindware/Parryware or equivalent make as per approved make list).)

S & F in repair Toilet paper Roll Holder with Stainless Steel Flap, and including chromium plated brass screws and wooden/plastic cleats, complete all as specified and as directed. Make : Jaquar Cat part No. ACN-CHR-1153Sand equivalent in jaquar / Hindware/ Parryware or equivalent make as per approved make list).)

S & F Designer type high quality fancy type looking mirror of size as approved by Engr-in-Charge 8-10mm thick, fixed to wall with stainless steel studs, screws, brackets and washers etc complete all as specified and as directed.

S&F in repair vitreous china wash down water closet pan pedestal pattern white including connection in drain and in flushing pipe complete including 'P' or 'S' trap complete all as specifed and directed. (Make : Jaquar/ Hindware/ Kohler)

S&F in repair vitreous china one piece counter top wash basin, white, of size 410x410x160 mm / 570x420x195 mm / 615x415x150 mm including coupling, bottle trap/waste pipe complete all as specified and directed. (Make : Jaquar/ Hindware/ Bathsense)

S&F in repair vitreous china wash basin, white, flat back, size 550x400 excluding taps, chain and plug and porcelain stopper but including brackets, coupling, bottle trap/waste pipe complete all as specified and directed. (Make : Jaquar/ Hindware/ Bathsense)

S&F in repair Plastic water closet seat, back, closed pattern with flat bottom , and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repair Brass CP sink mixer with swinging spout (wall mounted model with connecting legs & wall flangesfor making hot and cold water fixed as per manufacturers manual with long shunk and cup washers, screwed both ends suitable for 15mm bore GI Pipe joints to GI pipes or unions, complete all as specified and directed. Make : Jaquar Continental CON-CHR-309 KNM and as approved by GE

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including 40 mm waste fittings, brass chromium plated with long screwed shanks and fly nuts flange end bedded in red lead cementand other end fixed etc all as completed and specified.

S & F in reapir stainless steel kitchen plate rack minimum size 900 mm x 750 mm x 200 mm including fixing on wallmounted etc

S&F in repair Internal flushing kit complete set for flushing cistern complete all as specified and directed.

S&F in repair CP Grating 125 mm dia with waste hole or without waste hole

S&F in repair PVC (SWR) floor trap, plain with grating (waste hole/plain type) including jointing with solvent cement, 75 to 100 mm mm diameter of outlet, all as specified.

Demolition and breaking up drain pipes (SGSW, AC, PVC or reinforced cement) set in cement mortor internal dia of pipe 75 to100 mm complete all as specified and directed.

S&F of 110 mm bore SWR pipes single socketed in any length with rubber ring joints fixed to walls ,floors, trenches etccomplete all specified and directed.

Description all as per item No 93 above but 75 mm dia PVC SWR pipe.

S&F 110 mm bore PVC (SWR) bends with rubber ring joints fixed to walls complete all as specified and directed.

Description all as per item No 95 above but 75 mm dia PVC SWR bends.

Hacking out old broken glasses any thickness size, quality or description from wooden frames fixed with putty or with beads complete all as specified and as directed upto 8th floor Height.

Hacking out old broken glasses any thickness size, quality or description from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and as directed upto 8th floor Height.

M&L for 4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed upto 8th floor Height.

S&F 3mm thick Figured glass, pin head type and glazing with oil putty in square not exc 0.80 Sqm in each panes fixed any bldg hight complete all as specified and directed upto 8th floor Height.

Taking down cement or lime plaster any description on brick or stone walls etc including recking out joints hacking for key scrubbing down with waters etc.

M&L for rendering 15mm thick cement plaster in cement mortar (1:6) finished even & smooth without using extra cement on brick/concrete surfaces complete all specified and directed.

M&L 10 -12mm thick polymer modified readymix cement base plaster as per manufacturer instruction on fair / unfair faces of brick work or concrete surfaces & finishing the surface even & smooth as per manufacturer instruction complete all as specified & directed.

M&L for Rendering 5mm thick with water proofing compound in cement mortar 1:3 on fare faces of brick work or concrete surfaces and finished the surface even and smooth without using extra cement in ceiling/ Chajjas complete all as specified.

M&L for preparing New plasteres surfaces Wall and applying of wall care putty approx 2 mm thick on Wall as per manufacturer's instruction on existing prepared surface and make the surface smooth by rubbing with sand papers etc and applying two coats of oil emulsion distemper over a coat of primer paint on Wall complete all as specified and directed.

M&L for prepration of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of Primer complete all as specified and directed .

M&L for prepration of new plastered surfaces of wall/ Ceiling and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new/ Old surfaces. complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of ceiling applying wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two coats of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

S & F in repair SS soap dish, fixed in repairs, complete all as specified and as directed.

S&F in repair for Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

Preparation of new wood or wood based surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint, over a coat of primer complete all as specified and as directed.

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge.

S & F anodised aluminium , poweder coated of any colour, Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) including track size not less than 90 mm x 20 mm x 1.8 mm inbuilt roller track with rubber gasket and shutter stiles rail of aluminum section of size 40mmx 18 mmx1.5mm thick with suitable locking arrangement fixing glass pans in frame shutter covered with rubber packing, complete each shutters of window shall be provided with 2 Nos 100 mm aluminium handle etc all as complete all as specified and as directed.

S&F in repair Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel fixed in floor with over all length of cover plate 140 mm fixed in repairs complete.

S&F in repair Rubber door seal 32mm wide with Aluminium strip of size 19mm wide fixed with steel machine screws with washer, complete all as specified and as directed.

S&F in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, bright finished

S&F of cabinet mirror of size 14'X18' all as per specifiacation & directed by Engineer-in-charge.

S&F in repair SS Drawer handles, projection drop (50mm to 65mm) on screwed plate complete

S&F in repair fancy type Curtain rods decorative type stainless steel 25mm nominal dia of approved quality(Make VISTA) (1mm wall thickness) including fixing of two number decorative brackets fixed in brick/concrete wall, Two number of latto on both ends of curtain rods ( The length of each curtain rod will be 1.00m to 1.80m long) complete all as directed and specified.

Cutting shrubs, wild growth/trees n exc 30cm girth and removing complete vegetation growth from walls incl taking out roots from roofs/brick work/Shaft/RCC work joints etc and making good the disturbed surface with PCC 1:2:4 type B-0, using 12.5mm graded crushed stone aggregate including treating affected area with acid wash to check further growth of vegetation and disposing off the rubbish from site (MoD Land) from the above mentioned area complete all as specified and as directed. Note:- The rates quoted by the tenderers are deemed to be up to G+9 floor bldg included roof , external walls , shafts area and safety precautions , necessary T&P, scaffolding/jullha etc as required.

S&F in repair CI bend for 100mm bore any radius, diminishing pieces or tapers (larger bore measured), fixed to walls, complete all as specified and as directed.

S&F in repair CI bend for 75mm bore any radius, diminishing pieces or tapers (larger bore measured), fixed to walls, complete all as specified and as directed.

S&F in repair CI Branch 75mm bore pieces with access door tee/Y etc , single (equal or unequal ), ordinary or inverted ) (spigot or socket type ) or with parallel branches complete all as specified & directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 sqm each complete all as specified

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each complete.

Please Enable Macros to View BoQ information