RSI

Supplying of hot applied Thermoplastic road marking compound , 2.5 mm thick including relectorising glass beads @250 gms per sqm with Reflectorising Glass Beads on Bituminous Surface at 250 gms per sqm area , thickness of 2.50 mm is exclusive of surface applied glass bead as per IRc 35, the material should be of BERGERcompany / BERGER equivalent and must comply with the following a) white index of the product should be in the range of 60-70 when measured against the standard reference. the applied panel 7/8 number must be submitted for checking up the white index in the department lab. in case the department approves the white index of any vendor, the department engineer may carryout random checking of the applied products at site against the approved pannel. in case of any major deviation, beyond the acceptanc elimit, department reserve the right to cancel or reject the total supplied consigement by the desired material as per approved panel at his own cost and additional demurrages may be claimed due to loss os man days b) Luminace factor of the amterial should be in the range of 80-85% at 45 degree centigrade as per AASTHOM 249.c) Crack Resistance: The applied panel cured for 7 days under ambient condition and then should be tested as per BS 3262 part - 1 1989 and should pass at the range of 00 C to 100 C. d) Adhesion: Strong. e) Softenign point : 1020 C f) Dried film finish: Smooth and Uniform g) Night Vision: High as directed by the Enginer in harge and confroming to IS:164-1961 ( 1st revision reaffrimed in 1986) and clause confroming to IRC : 35-1997

Suppying and installation of Hazard markers using M.S. angle of size 55X55X6 mm and 120cm high above ground level painted with two coats of black and white stripes of 15Cm wide with first qulity synthetic enamel paint over one coat of appropriate primer of approved brand, colour with 30cmX90cm type IV of ASTMD 4956-09 High Intensity Prismatic Retro reflective sheeting Yellow colour and confirming to IRC 61:2012 fixed over 3 mm thick aluminium Composite Material (ACM) sheet having minimum 0.30 mm thick Aluminium skin on both sides with standard support in screen printing sloping downward at an angle of 45 degrees towards the side of the obstruction on which the traffic is to pass and buried in to the ground in a trench of size 30X30cm and 50cm depth filled with CC M20 including cost and conveyance of all materials, equipment, machinary and labour with all leads and lifts, lading, unloading charges necessary for successful completion of the work as directed by the Engineer in charge and confirming to IRC 79-1981 &MORTH Specification No. 805 and approved drawings etc.,complete for finished item of work.

Providing and fixing Cautionary/Warning sign boards size 900mm equilateral triangle made out of TYpe IV of ASTMD 4956-09 High Intensity Prismatic Retro reflective sheeting and conforming to IRC : 67 2012 for full back ground of white colour and letters/logos done by screen printing in Black colour, boarders by screening printing in Red colour and fixed over 3 mm thick aluminium Composite Material (ACM) sheet having minimum 0.30 mm thick Aluminium skin on both sides with back side painted with grey colour and fixed over back support frame of MS angle 25x25x3mm all round with MS angle 35x35x4mm and mounted on a MS angle post of size 75x75x6mm with clear height of not less than 2.1m from the ground level the bottom of the board. The signpost should be painted with one coat of red oxide paint and 2 coats of 1st quality synthetic enamel paint Black & White colour with bands of 30CM height. The signpost shall be firmly fixed with MS base angle 35x35x4 mm in to the ground by M 15 Concrete foundation of size 450x450x600mm, including cost and conveyance of all materials, equipment, machinary and labour with all leads and lifts, lading, unloading charges site clearance etc., and complete necessary for successful completion of the work as directed by Dept.

Supplying and installation of delineators double sided (Roadway indicators) not less than 800mm high above ground level. The delineator shall have a core and shell construction which shall be made of tough, high impact resistant, injection-molded, thermoplastic outer body. The inner core shall consist of powder coated or painted Mild steel of minimum thickness 1.0mm. The delineator should have top retro-reflective unit consisting of white color micro prismatic non metallic retro-reflective sheeting of minimum exposed area of 125 cm2 and bottom retroreflective unit consisting of red color micro prismatic non metallic retro-reflective sheeting of minimum exposed area of 35 cm2 confirming to ASTM D4956 type XI standards. The delineators shall be fixed to the ground by inserting the root of the delineator up to the marked portion and by firm concrete filling as per the instructions by engineer in-charge. (excluding GST)

Providing and fixing facility informatory sign board of size 600x800mm made out of Retro reflective sheeting of Type-IV of ASTMD 4956-09 High intensity Prismatic Retro reflective sheeting and conforming to IRC:67:2012 for full background of Green Colour and White letters and fixed over 3mm Aluminium composite Material sheet having minimum 0.30 mm thick Aluminium skin on both sides with back side painted grey colour and fixed over back support frame of MS angle 35x35x4mm and mounted on a MS angle post of size 75x75x6mm with clear height of not less than 2.1m from the groundlevel the bottom of the board. The sign post should be painted with one coat of red oxide paint and 2 coats of 1st quality synthetic enamel paint Black & White colour with bands of 30cm of height. The signpost shall be firmly fixed with MS base angle 35x35x4 mm in to the ground by M-15 concrete foundation of size 450x450x600mm, including cost and conveyance of all materials, equipment, machinery and labour with all leds and lift, loading charges necessary for satisfactory completion of the work as directed by the Engineer-in-Charge.

Painting 2 Coats after filling the surface with synthetic enamel paint in all shades on plastered concrete surface as per Tech Specification 800 MORTH (5th Revision) and as directed by the Engineer in Charge.

Providing and erecting a "W" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 810