SPECIAL REPAIR/ REPLACEMENT OF CFL POST TOP GRADEN LIGHTS INTO LED POST TOP GRADEN LIGHTS AT FLAG STAFF HOUSE AND CERTAIN OTHER SANCTIONES WORKS UNDER GE CHENNAI

Amount

Surface dressing n. exc. 15cm deep and getting out in soft/ loose soil all as specified and directed.

Surface excavation n. exc. 30cm deep and averaging 15cm deep and getting out in soft/ loose soil all as specified and as directed.

Excavation in post holes (or similar holes) in hard/ dense soil each hole n. exc. 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers n. exc. 25cm, watering and removing surplus soil to a distance n. exc. 50m and making good surfaces complete all as specified and directed.

Excavation in trenches in soft/ loose soil n. exc. 1.50m wide and n. exc. 1.50m deep for foundation, or for shafts, wells, cesspits, manholes, etc., n. exc. 10 sqm on plan getting out complete all as specified and directed.

Excavation in trenches in hard/ dense soil n. exc. 1.50m wide and n. exc. 1.50m deep for foundation, or for shafts, wells, cesspits, manholes, etc., n. exc. 10 sqm on plan getting out complete all as specified and directed.

Cutting hard standing/ road for laying cable/ protection pipe all as specified and directed.

M&L sand filling under floors or in foundation including watering, well ramming & consolidating in layers not exceeding 25cm thick complete all as specified and directed.

Returning filling in including spreading, leveling, watering & well ramming in layers not exceeding 25cm thick in soft/ loose soil complete all as specified and directed.

Removing excavated soil to a distance n. exc. 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Removing excavated soil to a distance exc. 50m but n. exc. 100m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L for broken stone or boulders hardcore of gauge n. exc. 63mm, deposited, spread and leveled in layers n. exc. 15cm thick, watered and rammed to a true surface complete all as specified and directed.

Supply only Integral liquid Water Proofing Compound conforming to IS: 2645-2003.

M&L for providing PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling mass concrete, sub base of floors etc. complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 (using 40mm graded tone aggregate) for filling and making good disturbed road/ hard standing etc. complete all as specified and directed.

M&L for providing PCC (1:2:4) type B-2 using 40mm graded stone aggregate as in foundation filling mass concrete, sub base of floors etc. complete all as specified and directed.

M&L for providing RCC (1:1½:3) type A-1 using 20mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc., basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for providing RCC (1:1½:3) type A-1 using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts etc., complete all as specified and as directed.

M&L for RCC (1:1½:3) type A-1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, deck slabs and the like all as specified and directed.

M&L providing precast cement concrete louvers and jallies, 25mm thick (measured solid), including all mouldings but excluding frame in cement concrete (1:2:4) type B-O (using 12.5 graded stone aggregate) set in cement mortar (1:4) complete all as specified and directed.

M&L for brickwork with old size fly ash bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6) complete all as specified and directed.

M&L for brickwork with old size fly ash bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:4) complete all as specified and directed.

Cutting holes in brick/ stone walls built in cement mortar or cement lime mortar for inserting hold fasts and making good dismantled portion in cement mortar (1:3) or cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate for the required depth of embedded portion of holdfasts or lugs measured from the face of jamb into the wall exc. half brick but n. exc. one brick complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter of flat rough finished surfaces of concrete all as specified and directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions, rough finished surface of concrete square, rectangular or polygonal complete all as specified and as directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam hunching, girders, bressummers, lintels, cantilevers, including supports, overhangs, etc. also splays between floors and beams complete of flat rough finished surfaces of concrete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work, not exc. 200mm thick (Horizontal or sloping) for fair finished surfaces of concrete flat complete all as specified and directed.

Use and waste of formwork to edges of concrete flats, breaks in floors, window cills, concrete railing and openings in concrete wall; floors and roofs and similar works exc. 10cm but n. exc. 20cm wide for rough finished surfaces of concrete all as specified and directed.

Taking down chowkats or frames with shutters (without taking of shutter from the frame) of any description alongwith fittings exc. 1.5sqm but n. exc. 4 sqm each complete all as specified and directed.

S&F fully glazed door shutter made out of 12mm thick toughened glass and roughened the glass fort mat finish by frosting, drilling holes for fixing handles including provision of 02 No. 400mm long stainless steel matt finished handles, suitable locking arrangement, centre lock, stainless steel floor spring, patch fitting consisting of bottom patch and top pivot with stainless steel fixing plate etc. including taking down existing shutter complete all as specified and directed. Note: The unit rate shall be deemed to include all necessary builder's hardware complete.

Taking down shutters of any description exc. 1 Sqm but n. exc. 2 Sqm each and resecuring in the same opening after cutting, easening etc with new iron mongry complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube all as per relevant details given in SSR against item No. 08095 of SSR Part-II and fitted to chowkats complete all as specified and as directed.

S&F factory made wood free EPS solid PVC moulded door shutter 28 to 30 mm thick (stiles) with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet Polyurethane painted on the front face and 2mm prelam colour PVC sheet on back face fixed to frame complete all as specified, directed and shown in sketch relevant to item No. 8103 in SSR Part-II.

S&F mild steel butt hinges, medium weight cold rolled 100mm size all as specified and as directed.

S&F aluminium anodised barrel tower bolts of extruded section 200mm long all as specified and as directed.

S&F extruded aluminium alloy handles cast type anodised 150mm size all as specified and directed.

S&F aluminium alloy anodized sliding door bolts; 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections complete all as specified and directed.

S&F floor mounted door closer, heavy duty with pivot and connected accessories, satin stainless steel finish, sustainable for long duration and suitable for 12mm thick toughened glass shutters all as per BTS 80 series of Dorma or equivalent of PAG or any other reputed make as approved by GE all as specified and directed.

M&L for mild steel TMT bars in reinforcement, 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-500D complete all as specified and as directed.

M&L mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-500D complete all as specified and directed.

S&F framed work such as grills, gratings etc., with ends of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks & similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

S&F rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with & including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails & guides) & hanging; also fastening & fixing Fe-410-O or Fe-310-O complete all as specified and directed.

S&F powder coated (minimum thickness of powder coating 50 micron) anodized aluminium for doors, windows, partitions, ventilators etc. with one or more rebates including joining cleats for fixing complete all as specified and directed.

S&F anodized aluminium powder coated (minimum thickness of powder coating 50 micron) door shutter of aluminium section for frame work not less than 0.55 Kg/ RM including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, stainless steel butt hinges 100mm long and shutters of section not less than 0.48 Kg/ RM (inter-lock) fully glazed and provided with 5mm thick tinted glass including anodised aluminium snap beads, screws etc. complete all as specified and directed.

S&F powder coated aluminium window and ventilator shutters side hung type without sash bar using aluminium section weighing not less than 0.55 Kg/RM including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings viz. 100mm long peg stay- 01 No., 100mm long hinge type B-21- 02 No. complete all as specified and directed

S&F anodized aluminium powder coated (minimum thickness of powder coating 50 micron) panelled door shutter of aluminium section for frame work not less than 0.55 Kg/ RM including necessary joining cleats, glazing clips, rubber neoprene packing, 2 No. 150mm long handles, 02 No. 200mm long tower bolts, 03 No. aluminium B21 hinges and 01 No. aluminium mortice lock in each door including anodised aluminium snap beads, screws etc. complete all as specified and directed. Note: Glass panes and pre-laminated particle board shall be measured and paid for separately under appropriate item of this BOQ.

S&F rolled mild steel roof trusses (framed), trussed purlins, crane gantries, rails & fastenings & heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. Gde Fe 410-W (Gde-E-250) quality-A complete all as specified and directed.

M&L for steel tubular trusses including special shaped washers etc, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 including one shop coat of zinc chromate primer paint (including preparation of surfaces) at contractor's workshop before fabrication complete all as specified and directed.

S&F rolled sections as in main and cross beams; hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates of Gde Fe- 410-O or Fe-310-O all as specified and directed.

S&F 1.00mm thick mild steel plain black sheet in wall cladding, steel gates and similar work cut to size, holes punched; including headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted welded seams including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

M&L 304 grade stainless steel pipes 2.00mm thick of section as directed as in posts and board frame for fixing retro reflective sheet of road sign boards including necessary welding, grinding etc. complete all as specified and directed.

Supplying 2.00mm thick retro reflective sheet of size 1.20m x 1.80m duly marked with layout of JCO’s/ OR’s Md Accn Qtrs and road layout including welding it to stainless steel frame work complete all as specified and directed. Note: SS frame work shall be measured and paid for separately under appropriate item of this BoQ.

S&F Pre-painted galvalume aluminium zink coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength 550Mpa as in roof covering fixed with self tapping screws as per manufacturer’s instruction complete all as specified and directed.

M&L for galvanised powder coated snap grid framework for false ceiling all as specified including Vinyl laminated MPL gypsum panels (GYPTECH) 9mm thick of size of 60cm x 60cm fixing with staples on snap grid on RCC slabs by means of GI wire not less than 4mm dia, hooks and rawl plugs etc. at 1200mm c/c of make GYPTECH/ ARMSTRONG OR equivalent complete all as specified and directed.

S&F pre-laminated particle board 18/ 19mm thick, interior grade pre-laminated on one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work as in cupboards etc. complete all as specified and directed.

S&F pre-laminated particle board 12mm thick, interior grade pre-laminated on one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work as in cupboards etc. complete all as specified and directed.

S&F pre-laminated particle board 9mm thick, interior grade pre-laminated on both sides with decorative choice lamination fixed with screws to timber frame work fixed in repairs complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified.

M&L 25mm thick cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate as in sub floor finished fair and even complete all as specified and directed.

M&L for light shade vitrified ceramic tiles 10mm thick (square/ rectangular) polished, area of each tile exc. 0.36 sqm but n. exc. 0.42 Sqm on vertical surfaces as in skirting laid over and including 15mm thick plaster in cement mortar (1:4) set & jointed in neat cement slurry & pointed in white or coloured cement to match complete all a specified and directed.

M&L Non skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exc. 0.11 Sqm but n. exc. 0.18 Sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

M&L glazed coloured ceramic tiles 7 to 8mm thick (square/ rectangular) of size matching to floor tile as approved by GE fixed on vertical surfaces set and jointed in neat cement slurry and pointed in coloured cement to match the tile laid over and including 10mm thick backing coat in cement mortar (1:4) complete all as specified and as directed.

M&L glazed coloured ceramic tiles of size 350mm x 250mm x 7mm/ 450mm x 300mm x 7mm thick laid on vertical surfaces set and jointed in neat cement slurry and pointed in coloured cement to match the tile laid over and including 10mm thick backing coat in cement mortar (1:4) complete all as specified and as directed.

M&L glazed coloured ceramic designer wall tiles 7 to 8mm thick of area exc. 0.11 Sqm but n. exc. 0.18 sqm as approved by GE laid on vertical surfaces set and jointed in neat cement slurry and pointed in coloured cement to match the tile laid over and including 10mm thick backing coat in cement mortar (1:4) complete all as specified and directed.

M&L for chequered cement concrete coloured tiles (Designer tiles) of size 40cm x 40cm x 25mm thick set, jointed and pointed in neat cement slurry and pointed with white cement ang pigment as in floors laid over and including 20mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

M&L 75mm thick PCC (1:2:4) type B-2 using 20mm graded stone aggregate as in sub floor finished fair and even complete all as specified and as directed.

M&L 75mm thick PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in plinth protection/ foot path etc. finished even and smooth without using extra cement complete all as specified and as directed.

M&L machine cut Kota stone slab 18-20mm thick as in flooring laid over and including 15mm thick screed bed in cement mortar (1:6); laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L machine cut Kota stone slab 18-20mm thick as in riser of steps, skirting, dado & pillars etc. laid over and including 15mm thick backing coat in cement mortar (1:6) & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed.

M&L 20mm thick rendering in cement mortar (1:4) mixed with water proofing compound applied on roof surface complete all as specified and directed.

Taking down cement plaster on brick work or stone walls etc. including racking out of joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed.

M&L for 15mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces finished the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 10mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces finished the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar (1:3) on concrete surfaces as in ceiling, finished even and smooth without using extra cement complete all as specified and directed.

M&L for applying three coats of white wash on ceilings including preparation of newly plastered surfaces complete all as specified and as directed.

M&L for applying three coats of white wash on walls including preparation of newly plastered surfaces complete all as specified and as directed.

M&L for preparation of old decorated plastered surfaces of walls including brooming down or by steel wire brushing, scrapping down smoke soot, moss and efflorescent salts and treating oil & greasy spots and applying two coats of white wash complete all as specified and as directed.

M&L preparation of newly plastered or previously untreated surface of walls and applying two coats of cement base paint, white or tinted over a coat of primer complete all as specified and directed.

M&L for applying two coats of distemper oil emulsion over a coat of primer on newly plastered surfaces of walls including preparation of surface complete all as specified and directed.

Supply and fix sheet glass 5.5mm thick plain, ordinary quality and glazing with oil putty in squares exc. 0.50 sqm in each pane complete all as specified and directed.

M&L preparation of new steel surfaces of any description not otherwise described over 10cm girth or width and applying two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S&F vitreous china wash basin white flat back size 630mm x 450mm (excluding taps, waste, chain and plug and porcelain stopper) but including brackets and 32mm dia PVC coupling complete all as specified and directed.

S&F 600mm x 450mm bevelled edged looking mirror 6mm thick with aluminium frame work fitted with 6mm thick commercial ply or AC sheet backing to mirror complete all as specified and directed.

M&L for 18 - 20mm thick machine cut granite slab (of any type), laid over and including 15mm thick cement screed in cement mortar (1:6), bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigments to match with the shades of granite stone as in platforms/ cooking tops including cutting and polishing etc., complete all as specified and directed.

M&L vitreous china wash down water closet (pedestal pattern) white with including white coloured PVC seat cover including connections to drain (or outgoing pipe) and flush pipe etc. complete all as specified and directed.

S&F vitreous china wash down water closet squatting pan Orissa pattern of size 580mm x 440mm with integral foot rest (white or light coloured) including making connection to soil pipes and flushing cistern complete all as specified and directed.

S&F PVC low level flushing cistern 10 litre with complete accessories such as PVC flush pipe, over flow pipe etc. complete all as specified and directed.

S&F vitreous china bowl urinal flat back, size of 465mm x 355mm x 265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

S&F 15mm PVC connection 450mm long with PTMT nuts of superior quality all as specified and directed.

S&F bib taps brass chromium plated with crutch or butter fly handle screwed down, screwed for 15mm bore iron pipe or for brass ferrule complete all as specified and directed.

S&F chromium plated 2-way double handle bib cock with flange screwed down, screwed for 15mm bore iron pipe or for brass ferrule as per Cat No. 8312 of Prayag or or equivalent from other makes specified in particular specifications complete all as specified and directed.

S&F 2-way PTMT bib cock with flange screwed down, screwed for 15mm bore iron pipe or for brass ferrule as per Cat No. 129-C of Prayag or or equivalent from other makes specified in particular specifications complete all as specified and directed.

S&F fancy type pillar taps cast copper alloy with capstan heads chromium plated screwed down, high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts screwed for 15mm bore iron pipe complete all as specified and directed.

S&F PTMT pillar tap fancy with foam flow as per Cat No. 131 of Prayag or equivalent from other makes specified in particular specifications suitable for 15mm bore pipe complete all as specified and directed.

S&F PTMT angle cock with flange as per Cat No. 144 of Prayag or equivalent from other makes specified in particular specifications all as specified and directed.

S&F angular stop valves brass chromium plated screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for union complete all as specified and directed.

S&F brass stop valves chromium plated fancy type screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for union complete all as specified and directed.

S&F chromium plated health faucet (hand shower) with 1.2metre long PVC tube with wall hook complete all as specified and directed. Make: Jaquar Cat No. ALD-563 or equivalent from other makes specified in particular specifications.

S&F PVC health faucet with 1.5m long tube and hook (Ivory) complete all as specified and directed. Make: Prayag Cat No. 188 or equivalent from other makes specified in particular specifications.

S&F swivel shower rose of size 100mm with swivel joints including PTMT shower arm 195mm long with bend of 45° with flange fixing with 15mm dia pipe (Minimum weight 40g shower and 40g arm) complete all as specified and directed.

S&F 45cm long PTMT towel rail fixed with and including chromium plated brass screws and plastic cleats (minimum weight 175g) complete all as specified and directed.

S&F PVC soap dish as per Cat No. 195 of Prayag or equivalent from other makes specified in particular specifications all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall etc. complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in floor/ trenches etc. complete all as specified and directed.

S&F 110mm dia PVC (SWR) bend any radius all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction double (Double `T') equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) floor trap, plain with grating including joining with solvent cement 110mm dia of outlet complete all as specified and directed.

S&F 25mm bore gun metal, globe or gate valve confirming to IS 778-1984 with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

S&F 1000 litre capacity three layered rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F 20mm bore ball brass valve, high pressure with polyethylene high density float and fly nut complete, screwed for iron pipe complete all as specified and directed.

S&F galvanised steel water tubing 15mm bore medium grade including provision of all pipe fittings such as bends, tees, elbows, reducers, unions, plugs, sockets etc fixed to walls, concealed in walls/ ceilings or laid in floors etc., complete all as specified and directed.

S&F galvanised steel water tubing 20mm bore medium grade including provision of all pipe fittings such as bends, tees, elbows, reducers, unions, plugs, sockets etc fixed to walls, concealed in walls/ ceilings or laid in floors etc., complete all as specified and directed.

S&F galvanised steel water tubing 25mm bore medium grade including provision of all pipe fittings such as bends, tees, elbows, reducers, unions, plugs, sockets etc fixed to walls, concealed in walls/ ceilings or laid in floors etc., complete all as specified and directed.

M&L 150mm x 100mm salt glazed stoneware gully trap, square or round mouthed, ‘P’ type all as specified and directed.

M&L intercepting trap 150mm dia internal dia of salt glazed stoneware, with square ends to inspection arms for building flush into manholes and setting in cement mortar (1:1) complete including concrete foundation of width and thickness as for pipes of same dia and haunching after setting. Cleaning arm to include a glazed ware stopper, galvanized iron bayonet joint (or other approved pattern) and galvanised iron lever (or trigger), galvanised iron chain, hook and ring complete all as specified and directed.

M&L cutting into existing manholes for connecting new drains upto 150mm dia and making good to pipe & rendering, cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate smooth finished & reforming benching as required complete all as specified and as directed.

Demolition of PCC in any situation n. exc. 15cm thick including removal of debries outside MD land complete all as specified and directed.

Demolition of brick masonry built in cement mortar including all quoins, arches, pillars, ashlars facings, dressed stone work and pre cast concrete articles etc., complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/ slabs/ blankets any thickness including cover fillets complete all as specified and directed.

Taking down old unserviceable/ damaged point wiring carefully of any size and description on teak wood batten/ through pipe (light, fan, socket etc) including removal of battens, pipes/ conduits, sockets, switches, shades, ceiling fittings, bulk head fittings ceiling rose etc complete and making good disturbed portion of wall to match with the existing surface all as specified and directed.

M&L for point wiring complete with 1.5sqmm (nominal area) PVC insulated unsheathed multi-stranded, (two run for Phase and Neutral) copper conductor FR & LS grade cable of 1100V grade conforming to IS -694 drawn through and including new non metallic rigid PVC conduit medium grade, ISI marked, 20mm bore with conduit accessories concealed In wall/ floor and fixed on ceiling/roof etc, including new pressed steel terminal boxes 1.6mm thick, concealed in walls with plastic laminated sheet cover 3mm thick as top cover fixed with cadmium plated screws for housing the switch sockets, outlets, fan regulator etc including provn of 1.5sqmm PVC insulated unsheathed copper conductor cable of green colour for earth continuity and connecting to common earth dolly etc., complete all as specified and directed for:-

One light point controlled by one switch.

One Fan/ Exhaust fan point controlled by one switch.

One 3 pin 5 amps socket outlet on the same board with other switches.

One 3 pin switch socket outlet, 5 Amps on independent board controlled by one switch.

M&L for point wiring complete with 2.5sqmm (nominal area) PVC insulated unsheathed multi-stranded, (two run for Phase and Neutral) copper conductor FR & LS grade cable of 1100V grade conforming to IS -694 drawn through and including new non metallic rigid PVC conduit medium grade, ISI marked, 20mm bore with conduit accessories concealed In wall/ floor and fixed on ceiling/ roof etc, including pressed steel terminal boxes 1.6mm thick, concealed in walls with plastic laminated sheet cover 3mm thick as top cover fixed with cadmium plated screws for housing the switch sockets, outlets, fan regulator etc including provn of 2.5sqmm PVC insulated unsheathed copper conductor cable of green colour for earth continuity and connecting to common earth dolly complete all as specified for one socket outlet (plug point) three pin 15 Amps controlled by one switch 15 Amps on independent board complete all as specified and directed.

S&F switch piano, flush type, single pole, one way, 5 Amps, 230 volts all as specified and directed.

Supply and fix socket outlet 2 in 1, 3 pin 5 Amps, 230 volts all as specified and directed.

Supply and fix switch socket combination flush type, 3 pin 15 Amps and 3 pin 5 Amps, 230 volts, 5 in 1, multipurpose, universal type complete all as specified and directed.

S&F ceiling rose PVC/ polycarbonate body 65 x 50mm 2 to 3 terminals 230 Volts, AC Single phase all as specified and directed.

Supply and fix switch socket combination, 2 in 1, 5 Amps, 230 volts flush type all as specified and directed.

Supply and fix switch socket combination flush type, 3 pin 15 Amps and 3 pin 5 Amps, 230 volts, 5 in 1, multipurpose, universal type complete all as specified and directed.

Supply and fix electronic ceiling fan regulator, flush type, 300 Watts all as specified and directed.

S&F ceiling fan 1200mm sweep including taking down old fan complete all as specified and directed. Make: Crompton Greaves/ Bajaj/ Usha/ Havells. Note: Old ceiling fan shall be deposited in MES store yard of AGE E/M after fixing new fan.

M&L taking down ceiling fan of any size, replacing ball bearings, capacitors etc. and spray painting using synthetic enamel paint after filling cavities with filler coat and hanging the fan in existing location complete all as specified and directed.

Hanging only ceiling fans including supply and fixing clamps, nuts & bolts, rubber bushes and making connections from ceiling rose to PVC connector with three core flexible wire of size 23/0.0076mm upto 3.0m in length complete all as specified and directed. Note: Ceiling fans shall be issued under Schedule ‘B’ ‘Free for hanging’ only.

Fixing only geyser 25 litre capacity including supply and grouting nuts & bolts of suitable size, cold water inlet pipe, hot water outlet pipe and making connection from socket outlet complete all as specified and directed. Note: Geysers shall be issued under Schedule ‘B’ ‘Free for Fixing’ only.

S&F wall mounted LED batten 20 watts in extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver all as per Cat No. LUMILINEPLUSBS20WLED865SPCSS of Havells or equivalent of other specified makes including 20 watts LED tube light fixed on wall surface or ceiling including taking down the old fitting complete all as specified and directed.

S&F environmental friendly, ultra modern, energy saving, surface mounted 10 Watts LED decorative oval bulkhead edge-lit LED luminaire comprising of high brightness including taking down the old fitting complete all as specified and directed. Make: Havells Cat No. RUGBYNEONFT 10WLED860SSYMTOPC or equivalent of other specified makes.

S&F 34 watts environment friendly, new generation, aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source suitable for 2' x 2' grid ceiling including taking down the old fitting complete all as specified and directed. Make: Havells Cat No. PLUTONEO2X2PLR34WLED840S of Havells or equivalent of other specified makes.

S&F turboforce 4 blade (300mm sweep) exhaust fans AC single phase 230/ 240 volts, heavy duty corrosion resistant body rigid frame with rubber mountings for minimal noise operation & maintenance free design with pressure die cast aluminium rotor mounted on two ball bearings with maximum air with minimum power consumption conforming to IS: 2312-1967 complete all as specified and directed.

Supply, fixing, connecting and testing factory made, MCB distribution board, made of 1.2mm thick CRCA sheet, powder coated conforming of IS - 13032, double door flush type fixed in switch boards/ wall at various places of capacity 240 Volts, 8 way, (MCB DB), SPN with 200 Amps rated bus bar neutral link, earth bar and din rail etc. conforming to IP 38 protection including taking down the existing distribution board complete all as specified and as directed. Note: MCB’s shall be measured and paid separately.

Supply, fix, connecting and testing factory made, MCB distribution board (MCB DB), IP 38, SPN, 4 way, 240 Volts, single door, flush type made out of 1.2mm thick CRCA sheet metal, Phosphatised, duly powder coated and conforming to IS 8623 with 200 Amps rated bus bar, neutral link, earth bar and din rail etc. fixed in switch board/ wall complete all as directed. Note: MCBs shall be measured and paid separately.

Supply, fix, connecting and testing isolator double pole, 40 Amps all as specified and directed.

Supply, fixing, connecting and testing MCB TPN, 63 Amps, 415 V of rupturing capacity 10kA, C curve type including taking down the existing one complete all as specified and as directed.

Supply, fixing, connecting and testing MCB SPN, 32 Amps, 240 volts of rupturing capacity 10kA, C curve type including taking down the existing one complete all as specified and as directed.

Supply, fix, connecting and testing MCB single pole (MCB SP), 6 to 32Amps, 240 volts of rupturing capacity 10kA, C curve type all as specified and directed.

Supply, fix, connecting and testing MCB single pole (MCB SP), 6 to 32Amps, 240 volts of rupturing capacity 10kA, C curve type fixed in repairs complete all as specified and directed.

S&F 34 watts environment friendly, new generation, aesthetically, ultra modern designed recess mounting luminaire with high brightness SMD LEDs as light source suitable for ceiling all as per Cat No. PLUTONEO2X2 PLR34WLED857S of Havells or equivalent of other specified makes fixed to ceiling including taking down the old fitting complete all as specified and directed.

Supply and fix LED 10 watts mirror light with diffuser all as per Cat No. LCL-10-CDL of Crompton Greaves or BN 550 WLED 12 - 6500 of Philips or LHESABP6IN1W009 of Havells or equivalent of other specified makes all as specified and directed.

S&F wall mounted LED batten 20 Watts LED 6000K (600mm) in extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver including 20Watts LED tube light all as per Cat No. ENDURALINEARNEO BS20WLED 865SPCWH of Havells or equivalent of other specified makes fixed on surfaces of wall or ceiling complete all as specified and directed.

M&L for submain wiring complete with two runs of 4.0 Sqmm single core, multi-stranded, FR PVC insulated unsheathed cable 1100 volts grade with copper conductor, drawn through and including new rigid non metallic PVC conduit medium grade ISI marked 20mm external dia concealed in wall/ floor along with conduit fittings and accessories, fixed on ceiling with one run of 4.0 Sqmm PVC insulated unsheathed copper conductor cable as earth continuity conductor and connecting to common earth dolly complete all as specified. Note: Two runs of 4.0sqmm multi-stranded cable and one run of 4.0sqmm cable as earth continuity conductor alongwith PVC conduit shall be considered as one unit length.

All as per item No. 149.00 above but including taking down existing submain wiring.

Taking out existing PVC/ XLPE cable 1100 volts grade LT cable of size 185 sqmm 3½ core with glands, bricks/ cable protection pipe, cable route indicators etc. from the trench/ fixed along wall or passing through pipes/ in floor, removing the unserviceable/ faulty cable and stacking serviceable cable for re-use complete all as specified and directed. Note: Excavation and earthwork will be measured and paid separately under appropriate items.

Taking out existing PVC/ XLPE cable 1100 volts grade LT cable of size 150 sqmm 3½ core with glands, bricks/ cable protection pipe, cable route indicators etc. from the trench/ fixed along wall or passing through pipes/ in floor, removing the unserviceable/ faulty cable and stacking serviceable cable for re-use complete all as specified and directed. Note: Excavation and earthwork will be measured and paid separately under appropriate items.

Supply, laying, connecting up and testing XLPE insulated armoured LT UG electric cable with aluminium conductor 1100 V grade of size 6 sqmm 2 core laid in trenches, fixed along wall or passing through pipes/ in floors including taking out existing cable complete all as specified and directed.

Supply, laying, connecting up and testing XLPE insulated armoured LT UG electric cable with aluminium conductor 1100 V grade of size 6 sqmm 4 core laid in trenches, fixed along wall or passing through pipes/ in floors complete all as specified and directed.

Supply and laying in trenches, fixed on wall (or) passing through pipes/ in floors including connecting up, testing and commissioning of XLPE insulated screened PVC bedded galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 185 Sqmm 3½ core complete all as specified and directed.

Supply and laying in trenches, fixed on wall (or) passing through pipes/ in floors including connecting up, testing and commissioning of XLPE insulated screened PVC bedded galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 150 Sqmm 3½ core complete all as specified and directed.

Supply, lay/ spread in trenches clean dry sand to required width and depth at bottom and top of cable including spreading, levelling, punning for laying/ cushioning of cable all as specified and as directed. Note: Punned thickness only will be considered or payment.

Supply and lay burnt bricks, old size, sub class 'B', laid flat adjacent to each other, perpendicular to cable with width equal to length in trenches for protection of cable all as specified and as directed.

Supply and lay 40mm bore GI light grade pipe laid in trenches/ floor for cable protection/ fixing on top of post top fitting including cutting, welding etc. as require including taking up/ down existing tubing complete all as specified and as directed.

Supply and lay 50mm bore GI medium grade pipe laid in trenches/ floor for cable protection/ fixing on top of post top fitting including cutting, welding etc. as require including taking up/ down existing tubing complete all as specified and as directed.

Supply and lay 80mm bore GI light grade pipe laid in trenches/ floor for cable protection/ fixing on top of post top fitting including cutting, welding etc. as require including taking up/ down existing tubing complete all as specified and as directed.

Supply and fix environmental friendly, long life aesthetically designed aluminium landscape luminaire for diffused lighting with high power LED as light source including taking down the old fitting complete all as specified and directed. Make: Havells Cat No. BAMBOOBL8WLED830PSYMTOPCM (1.0m) or equivalent of other specified makes

Supply and fix junction box made out of one piece mould SMC base SMC door with hinged cover suitable for and including provision of 10mm thick hylam sheet connector block for incoming and outgoing cable for connecting with bolts and nuts including provn of one cut out 16 Amps with neutral link for street light fixed on steel/ RCC poles with suitable clamps made out 15mm x 6mm flat iron, bolts, nuts and washers etc., including dismantling old box complete all as specified and as directed.

Supply, fix, connecting and testing MCB TPN 63 Amps, 415 volts of rupturing capacity 10 kA, C curve type including taking down the existing unserviceable MCB complete all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.3mm thick burried directly in ground vertically to a depth not less than 2.25m deep below ground level with top edge of plate not less than 1.5 below ground level connected to GI 4mm earth wire by means of bolts, nuts check nuts washers made of galvanised iron or steel earth wire protected by GI pipe 15mm bore light grade connected upto switch board including 20mm bore GI water pipe with funnel and wire mesh all as shown in electrical plate No. 3 of MES Schedule Part-I including dearth chamber of PCC (1:2:4) type B-1 using 20mm grade aggregate with 40mm thick RCC cover slab (1:1½:3) type A-0 using 12.5mm graded stone aggregate reinforced with 8mm dia TMT bars @ 100mm c/c both ways and 6mm dia MS lifting hooks including testing on completion complete all as specified and as directed.

DJ Group

G.L.THIRUMALAI NAIDU AND COMPANY

G.JANAKIRAMAN CO