Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹40.4 LAccepted-AOC 31 TILAK NAGAR SRI GANGANAGAR 335001 RAJ | GANGANAGAR | RAJASTHAN | 335001 | ₹40.4 L | L1 | Accepted-AOC L1 Bidder |
| 2 | L2₹42.5 LRejected-Finance | ₹42.5 L | L2 | Rejected-Finance Not the lowest Bidder |
| 3 | L3₹48.8 LRejected-Finance 1630 SECTOR 7C CHANDIGARH 160019 | CHANDIGARH | CHANDIGARH | CHANDIGARH | 160019 | ₹48.8 L | L3 | Rejected-Finance Not the lowest Bidder |
| Sl No | Description | Qty | Unit | Singla Electricals L1 | Ganganagar Enterprises L2 | SAGGI ELECTRIC COMPANY L3 |
|---|---|---|---|---|---|---|
| 1.00 | Disconecting all electric connections of LT Panel/Feeder Pillar box/Bus bar Chamber and removing the damaged/unserviceble components, including Welding/brazing the sheet metal enclouser at the rusted places and spray painting with synthetic enamel paint of existing colour over a coat of red oxide primer and refixing the same after replcement the defective parts complete all as specified and directed by Engr-in-Charge. Note- (i) The new spare parts required for replacement shall be measured and paid separately.
(ii) Relevent T&P and testing equipments/tools and minor accessories are arranged by the contractor and included in the unit rate of item. | 40 | Each Job | 5,000 ₹2 L | 500 ₹20,000 | 3,100 ₹1.2 L |
| 2.00 | Supply only MCCB 400 Amps ,4 Pole 36 KA of LT panel /Feeder pillar box required for replacement of unserviceable item obtained from item No- 01 above complete all as specified and as directed by Engineer -in -charge. | 5 | Each | 20,300 ₹1.0 L | 22,000 ₹1.1 L | 39,525 ₹2.0 L |
| 3.00 | All as per Srl item No. 02 here-in-before but Supply only MCCB 315/350 Amps ,4 Pole 35 KA complete all as specified and as directed by Engineer -in -charge. | 6 | Each | 18,000 ₹1.1 L | 22,000 ₹1.3 L | 24,025 ₹1.4 L |
| 4.00 | All as per Srl item No. 02 here-in-before but Supply only Euroload chaneover switch four pole 200 Amps ,4 Pole complete all as specified and as directed by Engineer -in -charge. | 1 | Each | 15,000 ₹15,000 | 15,000 ₹15,000 | 19,375 ₹19,375 |
| 5.00 | All as per Srl item No. 02 here-in-before but Supply only Euroload chaneover switch four pole 100 Amps ,4 Pole, complete all as specified and as directed by Engineer -in -charge. | 1 | Each | 5,600 ₹5,600 | 12,000 ₹12,000 | 10,075 ₹10,075 |
| 6.00 | All as per Srl item No. 02 here-in-before but Copper Bus -bar 400 Amps ,4 Way complete all as specified and as directed by Engineer -in -charge. | 5 | Each | 12,000 ₹60,000 | 20,000 ₹1 L | 16,740 ₹83,700 |
| 7.00 | All as per Srl item No. 02 here-in-before but Copper Bus -bar 200 Amps ,4 Way complete all as specified and as directed by Engineer -in -charge. | 4 | Each | 7,200 ₹28,800 | 3,500 ₹14,000 | 13,640 ₹54,560 |
| 8.00 | All as per Srl item No. 02 here-in-before but Copper Bus -bar 100 Amps ,4 Way complete all as specified and as directed by Engineer -in -charge. | 3 | Each | 4,500 ₹13,500 | 3,000 ₹9,000 | 8,990 ₹26,970 |
| 9.00 | All as per Srl item No. 02 here-in-before but Digital type Ammeter 0-400 amps with suitable CTs complete all as specified and as directed by Engineer -in -charge. | 5 | Each | 2,000 ₹10,000 | 1,200 ₹6,000 | 2,248 ₹11,240 |
| 10.00 | All as per Srl item No. 02 here-in-before but Digital Voltmeter 0-500 V with PTs complete all as specified and as directed by Engineer -in -charge. | 5 | Each | 1,500 ₹7,500 | 1,200 ₹6,000 | 2,248 ₹11,240 |
Updated dates
Tender Value
Refer Docs
EMD Value
₹1.0 L
Closing Date
27 Oct 2025, 6:00 pmClosed
HQ CWE SRI GANGANAGAR
HQ CWE POST BOX 48 SRI GANGANAGAR-335001 (Rajasthan)
REPAIR / MAINT OF EXTERNAL ELECTRIFICATION LT NETWORK INCLUDING UG CABLE, ELECTRICAL PANELS AND ALLIED WORKS AT SRI GANGANAGAR MIL STN
2025_MES_733235_1
CA NO CWE SGNR/TOKEN-64 OF 2025-26
Open Tender
Electrical and Maintenance Works
180 days
GE SRI GANGANAGAR
AS PER NIT
8 documents required · 8 mandatory
₹1,000
GE SRI GANGANAGAR
₹1.0 L
Yes
2 Jan 2026
29 Sept 2025
28 Oct 2025
29 Sept 2025
27 Oct 2025
13 Oct 2025
Amount
Disconecting all electric connections of LT Panel/Feeder Pillar box/Bus bar Chamber and removing the damaged/unserviceble components, including Welding/brazing the sheet metal enclouser at the rusted places and spray painting with synthetic enamel paint of existing colour over a coat of red oxide primer and refixing the same after replcement the defective parts complete all as specified and directed by Engr-in-Charge. Note- (i) The new spare parts required for replacement shall be measured and paid separately. (ii) Relevent T&P and testing equipments/tools and minor accessories are arranged by the contractor and included in the unit rate of item.
Supply only MCCB 400 Amps ,4 Pole 36 KA of LT panel /Feeder pillar box required for replacement of unserviceable item obtained from item No- 01 above complete all as specified and as directed by Engineer -in -charge.
All as per Srl item No. 02 here-in-before but Supply only MCCB 315/350 Amps ,4 Pole 35 KA complete all as specified and as directed by Engineer -in -charge.
All as per Srl item No. 02 here-in-before but Supply only Euroload chaneover switch four pole 200 Amps ,4 Pole complete all as specified and as directed by Engineer -in -charge.
All as per Srl item No. 02 here-in-before but Supply only Euroload chaneover switch four pole 100 Amps ,4 Pole, complete all as specified and as directed by Engineer -in -charge.
All as per Srl item No. 02 here-in-before but Copper Bus -bar 400 Amps ,4 Way complete all as specified and as directed by Engineer -in -charge.
All as per Srl item No. 02 here-in-before but Copper Bus -bar 200 Amps ,4 Way complete all as specified and as directed by Engineer -in -charge.
All as per Srl item No. 02 here-in-before but Copper Bus -bar 100 Amps ,4 Way complete all as specified and as directed by Engineer -in -charge.
All as per Srl item No. 02 here-in-before but Digital type Ammeter 0-400 amps with suitable CTs complete all as specified and as directed by Engineer -in -charge.
All as per Srl item No. 02 here-in-before but Digital Voltmeter 0-500 V with PTs complete all as specified and as directed by Engineer -in -charge.
All as per Srl item No. 02 here-in-before but Indicator Lamp( R,Y,B) Make L&T complete all as specified and as directed by Engineer -in -charge.
Disconecting all electric connections of APFC panel and removing the damaged/unserviceble components, Cleaning,trouble shooting,programing of APFC relay,tightning of all terminals and overhauling the APFC panels,Maintaining the Power Factor 0.99 at APFC panel & calibration after fixing all as specified and directed by Engr-in-Charge. Note :- (i) The new spare parts required for replacement shall be measured and paid separately. (ii) Relevent T&P and testing equipments/tools and minor accessories are arranged by the contractor and included in the unit rate of item.
Supply only heavy duty capacitor 2 KVAR required for replacement of unserviceable item in Srl item No. 13, complete all as specified and directed by Engineer-in-Charge.
Supply only heavy duty capacitor 3 KVAR required for replacement of unserviceable item in Srl item No. 13, complete all as specified and directed by Engineer-in-Charge.
Supply only heavy duty capacitor 4 KVAR required for replacement of unserviceable item in Srl item No. 13, complete all as specified and directed by Engineer-in-Charge.
Supply only heavy duty capacitor 5 KVAR required for replacement of unserviceable item in Srl item No. 13, complete all as specified and directed by Engineer-in-Charge.
Supply only heavy duty capacitor 10 KVAR required for replacement of unserviceable item in Srl item No. 13, complete all as specified and directed by Engineer-in-Charge.
Supply only heavy duty capacitor 15 KVAR required for replacement of unserviceable item in Srl item No. 13, complete all as specified and directed by Engineer-in-Charge.
Supply only heavy duty capacitor 20 KVAR required for replacement of unserviceable item in Srl item No. 13, complete all as specified and directed by Engineer-in-Charge.
Supply only heavy duty capacitor 25 KVAR required for replacement of unserviceable item in Srl item No. 13, complete all as specified and directed by Engineer-in-Charge.
Supply only heavy duty capacitor 30 KVAR required for replacement of unserviceable item in Srl item No. 13, complete all as specified and directed by Engineer-in-Charge.
Supply only AC 3 phase Power contactors 16 A WITH ADD ON 4 NO+4 N C required for replacement of unserviceable item in Srl item No. 13, complete all as specified and directed by Engineer-in-Charge.
Supply only AC 3 phase Power contactors 70 A required for replacement of unserviceable item in Srl item No. 13, complete all as specified and directed by Engineer-in-Charge.
Supply only 8 Step APFC Relay required for replacement of unserviceable item in Srl item No. 13, complete all as specified and directed by Engineer-in-Charge.
Supply only 12 Step APFC Relay required for replacement of unserviceable item in Srl item No. 13, complete all as specified and directed by Engineer-in-Charge.
S&F in existing panel, LED multifunction meters for showing parameters, V.A.F.PF.KW /KVA, KVAR, kWh,kVARh, Runhours etc complete all as specified and directed by Engineer-in-Charge.
S&F in replacement street light timer switch i.e. nature switch which works on the basis of measurement of lux level of infra red rays along with enclosure box having dust and termite proof, outdoor type mounted on electric panel or on pole single phase with contactor, MCB rating 63 Amps with load bearing capacity of 5 KW complete all as specified and directed by Engineer-in-Charge.
S&F in replacement street light timer switch i.e. nature switch which works on the basis of measurement of lux level of infra red rays along with enclosure box having dust and termite proof, outdoor type mounted on electric panel or on pole three phase with contactor, MCB rating 63 Amps with load bearing capacity of 12 KW complete all as specified and directed by Engineer-in-Charge.
Taking out old u/s LT panel/Feeder pillar box /Bus bar panel of any size/capacity and deposit to MES Store yard complete all as specified and directed by Engineer-in-Charge.
S&F on pole / wall /in panel , Sheet metal enclosure 3.15mm thick, Bus bar chamber consisting 4 pole 400 Amp 415 volts ,copper bus bar suitable for connecting cable as a junction including connecting of existing cables with suitable sizes aluminum thimbles and MCCB 4 Pole 250 Amp 415 , 36 KA all as specified & directed by Engineer-in-Charge.
S&F on pole / wall /in panel , Sheet metal enclosure 3.15 mm thick Bus bar chamber consisting 4 pole 250 Amp 415 volts ,copper bus bar suitable for connecting cable as a junction including connecting of existing cables with suitable sizes aluminum thimbles and MCCB 4 Pole 160 Amp 415 , 16 KA all as specified & directed by Engineer-in-Charge.
S&F on pole / wall /in panel , Sheet metal enclosure 3.15mm thick Bus bar chamber consisting 4 pole 160 Amp 415 volts ,copper bus bar suitable for connecting cable as a junction including connecting of existing cables with suitable sizes aluminum thimbles and MCCB 4 Pole 100 Amp 415 , 16 KA complete all as specified and directed by Engineer-in-Charge.
Supply, install, test and commisioning in replacement of LT panel duly powder coated of suitable size outdoor cubical type factory made, weather & vermin proof made out of CRCA sheet 3.15mm,750 mm depth (outdoor type) thick machine pressed with bottom frame made out of angle iron 50mm x 50mm x 6mm and 600mm long 4 legs duly painted with 2 coats of synthetic enamel paint over a coat of red oxide primer on exposed surfaces grouted in PCC 1:2:4 type B1 using 20mm graded stone aggregate blocks of size 30cm x 30cm x 60cm and 100mm thick PCC (1:2:4) type B1 floor over 100mm thick sub base of brick hardcore extended 100mm on all sides below panel body complete and suitable for 415 Volt AC 3 phase, 4 strip having insulated Copper bus bar 250 Amps from pole with openable double shutter on both sides (rear and front side) with locking arrangment duly pre-wired with suitable size of copper conductor cable fitted with Incomingproper size copper lugs/thimbless and connecting the incoming and outgoing MCCBs with suitable size strip duly bended and drilled and fixed with nuts, bolts & washers from bus bar to MCCBs etc duly fitted with and including the following accesories & all connected items complete. Incoming (i) MCCB 160 Amps, four pole with fixed thermal magnetic release, 415 V AC supply, having rupturing capacity 36 KA - 01 No Outgoing (ii) MCCB 63 Amps, Four pole with fixed thermal magnetic release, 415 volts having rupturing capacity 25 KA - 3 Nos (iii) MCCB 40 Amps, Four pole with fixed thermal magnetic release, 415 volts having rupturing capacity 25 KA - 1 Nos (iv) Indicating lamps set RYB - 01 Set (v) Digital Amp Meter 0- 160 A with CT , Digital Voltmeter 0- 500 V
Supply, install, test and commisioning in replacement of LT panel duly powder coated of suitable size outdoor cubical type factory made, weather & vermin proof made out of CRCA sheet 3.15mm,750 mm depth (outdoor type) thick machine pressed with bottom frame made out of angle iron 50mm x 50mm x 6mm and 600mm long 4 legs duly painted with 2 coats of synthetic enamel paint over a coat of red oxide primer on exposed surfaces grouted in PCC 1:2:4 type B1 using 20mm graded stone aggregate blocks of size 30cm x 30cm x 60cm and 100mm thick PCC (1:2:4) type B1 floor over 100mm thick sub base of brick hardcore extended 100mm on all sides below panel body complete and suitable for 415 Volt AC 3 phase, 4 strip having insulated Copper bus bar 400 Amps from pole with openable double shutter on both sides (rear and front side) with locking arrangment duly pre-wired with suitable size of copper conductor cable fitted with Incomingproper size copper lugs/thimbless and connecting the incoming and outgoing MCCBs with suitable size strip duly bended and drilled and fixed with nuts, bolts & washers from bus bar to MCCBs etc duly fitted with and including the following accesories& all connected items complete . Incoming (i) MCCB 250 Amps, four pole with adjustable thermal adjustable magnetic release, 415 V AC supply, having rupturing capacity 36 KA -01 No Out going (i) MCCB ,4 pole adjustable thermal fixed magnetic 100 Amp, 18 KA -02 Nos (ii) MCCB ,4 pole adjustable thermal fixed magnetic 63 Amp, 18 KA -03 Nos (iii) MCCB 4 Pole 32 Amp 18KA -01 No (iv) Indicating lamps set RYB - 01 Set (v) Digital Amp Meter 0- 250 A with CT , Digital Voltmeter 0- 500 V
M & L for Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried in ground (earth pit not less than 2.25 Mtr deep below normal ground level with top edge of the plate not less than 1.5 Mtrs below normal ground level, connecting to the Galvanised iron earth lead 32 x 6 mm size by means of bolts, nuts check nuts and washers of galvanised iron and 32 x 6 mm GI earth lead protection by provision of GI medium grade pipe 40 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20mm graded stone aggregate with 40mm thick cover of RCC (1:2:4) reinforced with XPM (wieght not less than 4gs/Sqm) and frame of angle iron 25mm x 25mm x 6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape, GI light grade slotted type 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed on top edge of earth plate common salt and charcoal filling test point made out of 40mm x 8 mm FI with fixing arrangements, funnel, wire mesh and earth work in hard dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 Mtrs all as per electrical Plate No.3 of SSR Part I and connecting to earth test point all as specified or indicated including testing on completion, complete all as specified and directed by Engineer-in-Charge.
Taking out/down defective cable any Type/size cable including disconnecting/dismantling all the electrical connections all as required at site and deposite to MES Store yard complete all as specified and all as directed.
Disconnecting of unserviceable ACSR conductor/AAC conductor of any size and any type and deposite to MES Store yard complete all as specified and all as directed.
Dismantling of cross arm, clamps , bracing etc of MS section complete all as specified and all as directed.
Dismantling unserviceable/defective LT (Pin type, Shackle type) insulators of any size/type and deposite to MES Store yard complete all as specified and all as directed.
Dismantling broken/damaged PCC /steel Poles/struts, any size and removing from site and deposite to MES Storeyard complete as specified and as directed.
Relaying of serviceable LT cable received in item 37 above from 10 sqmm to 240 sqmm 2/3.5/4 core in same or other trenches/wall surfaces/flooring/road and testing on completion including good all disturbed surfaces to match with existing complete all as specified and directed. Note : Earth work viz excavation, sand cushioning will be measured and paid seprately.
Supply, laying, Jointing and testing XLPE Cable 240 sqmm 3.5 core Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor in trenches or fixing to wall/pole or passing through pipe and including making good to all disturbed surfaces/flooring/tiling/road to match with existing specifications complete all as specified and directed by Engr-in-Charge.
All as per Srl item No. 43 here-in-before but XLPE cable of size 185 Sqmm 3.5 Core complete all as specified and directed by Engr-in-Charge.
All as per Srl item No. 43 here-in-before but XLPE cable of size 150 sqmm 3.5 Core complete all as specified and directed by Engr-in-Charge.
All as per Srl item No. 43 here-in-before but XLPE cable of size 120 Sqmm 3.5 Core complete all as specified and directed by Engr-in-Charge.
All as per Srl item No. 43 here-in-before but XLPE cable of size 35 sqmm 3.5 core complete all as specified and directed by Engr-in-Charge.
All as per Srl item No. 43 here-in-before but XLPE cable of size 25 sqmm 4 core complete all as specified and directed by Engr-in-Charge.
Excavation in trenches, not exc 1.5 m wide and n. exc 1.5 m depth; or n exc 10 Sqm on plan and n exc 1.5 m in depth for foundations of poles, struts, stays etc. or laying underground cable etc. in soft/loose soil, & getting out including taking out old brick or precast cable cover for reuse complete.
Returning, filling in, excavated soil including spreading, levelling, watering and well ramming in layers n.exc 25cm thick complete.
Removal of excavated surplus soil to a distance n.exc 50m and depositing where directed at level not exceeding 1.5 m above the starting point comlete.
Supply and laying double wall corrugated pipe DWC Pipe outer dia 120mm and inner dia 103mm, Non-metallic, resistance to compression : type 450, resistance to impact; normal, resistance to bending: pliable, resistance to external influence; ingress protection: IP 67, resistance against corrosion: without protection, resistance to flame propagation: non flame propagating, conforming to IS-16205 (part-24) 2017 including necessary jointing material i.e snap fit coupler with rubber ring, sealing plug, tees, bend, angel bend etc for passing electrical cable complete all as specified and directed by Engr - in charge
All as per Srl item No. 52 here-in-before but DWC Pipe outer dia 75mm and inner dia 61mm complete all as specified and directed by Engr - in charge
M & L for boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine for laying of DWC pipe of upto 120 mm dia suitable for 0.4 mpa working pressure complete all as specified and directed by Engr - in charge
Supply and erecting factory made 7 Mtr long hot dip galvanised octagonal pole with 130 mm dia including 1.5 Mtr single Arm HDG OD-48.3 at bottom and 70 mm dia at top A/F made up of 3mm thick HT sheet along with foundation type base plate of size 220X220X12 mm foundation bolt 4 nos of M20X750 high J type EN8 Grade with inbuilt junction box suitable for incoming 3 phase LT cable 16sqmm 4 core having 6A SP B class MCB fixed on bakelite sheet and stud type connector inside the pole, the pole shall be adequetly strengthened at the location of the door to compensate for the loss in section including excavation and RCC/PCC (1:2:4) type B1 for foundation and grouting the bolts as per manufactures instructions including marking pole numbers in letters and figures of size radium tape not less than 10cm height with red colour enamel paint complete all as specified and as directed. Note- New LED Street light will be issued from B/S Store yard.
M & L in replacement PVC insulated, PVC sheathed Copper conductor electric cable 1.5 Sq mm 3 Core 1100 volts grade for pole box to street light fitting complete all as specified.
Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material heat Shrink type and accessories suitable for 3 ½ / 4 core XLPE, armoured, Al conductor cable of size 10 to 16 sqmm,Indoor/Outdoor type complete all as specified.
Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material heat Shrink type and accessories suitable for 3 ½ / 4 core XLPE, armoured, Al conductor cable of size 25 to 50 sqmm,Indoor/Outdoor type complete all as specified.
Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material heat Shrink type and accessories suitable for 3 ½ / 4 core XLPE, armoured, Al conductor cable of size 70 to 95 sqmm,Indoor/Outdoor type complete all as specified.
Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material heat Shrink type and accessories suitable for 3 ½ / 4 core XLPE, armoured, Al conductor cable of size 120 to 150 sqmm,Indoor/Outdoor type complete all as specified.
Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material heat Shrink type and accessories suitable for 3 ½ / 4 core XLPE, armoured, Al conductor cable of size 185 to 240 sqmm,Indoor/Outdoor type complete all as specified.
Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material heat Shrink type and accessories suitable for 3 ½ / 4 core XLPE, armoured, Al conductor cable of size 300 to 400 sqmm,Indoor/Outdoor type complete all as specified.
M&L for 190 cm dia cable route indicator made of CI plate 8 mm thick with spike to angle iron 25 x 25 x5mm, 40 cm long makred as LT cable complete including fixing and excavation in soft/loose/hard/dense soil, PVC embedded block size 300x300x300 mm (1:3:6) type C-1 using 20 mm graded stone aggreggate complete all as specified and directed by Engineer-in-Charge.
Cutting/ trimming of tree branches not exc 10cm girth touching/approaching the LT/HT overhead lines with hack saw/axe to clear the LT/HT line upto 3 metre on each side (Horizontal and / or vertical) including disposal of trimmed branches 2 KM away inside the cantonment area & clearing site complete all as specified and directed by Engineer-in-Charge. Note :- 3 metre width on each side of LT/HT line shall be cleared and each span having not less than 3/5 conductors and min30-40 m pole to pole distance.
M&L for surface excavation not exceeding 30 cm deep and averaging 15cm deep in soft/ loose soil and getting out including cutting of grass roots, bushes if any and filling of lower portion with soil obtained from cutting or dressing complete all as specified and directed by Engineer-in-Charge.
Restring/Fixing only of ACSR conductor any size/any type drawn on fixed to insulator on the pole complete as with permissible sags for OH Conductor as per Indian Electricity Rules 1956 - Para 77 and 79 all as specified and directed.
M&L for Insulator Shackle type, porcelain, vitreous, white,brown or green , shall be in one piece and shall have a groove on the side and a hole for a cotter pin and two galvanised bolts 12 mm dia and nuts with or without a pair of straps in size 31 x 3 mm as indicated size height 75 mm and dia 90 mm, for working pressure 1100 volts complete as specified.
M&L for Insulator Pin type, porcelain, vitreous, white,brown or green including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 100 mm height, 65 mm dia for 1100 volts grade, shall be in one piece and have a top groove and shall be threaded to take galvanised mild steel pin complete as specified and as directed.
Ganganagar Enterprises (BID ID -3460390)
SAGGI ELECTRIC COMPANY (BID ID -3455717)
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.32 MB
BOQ_820983.xls
BOQ • 0.29 MB
Tender64.pdf
Tender Documents • 1.05 MB
Download all tender documents and submit your bid