SPL REPAIR TO ROOF SHEETING OF BLDG NO P-68 (GUN SHED) AND PROVN OF GUARD ROOM AT MAIN GATE OF UNIT UNDER AGE B/R-II AT ITARANA, ALWAR

Amount

Suface excavation n exc 30cm deep and averaging 15cm deep in any type of soil complete all as specified and directed.

Excavation in trenches not exceeding 1.50m wide and not exc 1.50m in depth and getting out in any type of soil complete all as specified and directed.

All as per item No 2.00 herein above but depth exc 1.5 m but n exc 3 m complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing surplus excavated soil to a distance exc 50 metre and n exc 100 metre and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

M&L PCC (1:4:8) type D-2, using 40 mm graded stone aggregate in fdn mass concrete complete all as specified and directed.

M&L RCC work M-25 Design Mix (using 20mm graded crushed stone aggregate) as in foundation including, raft, plinth beam bases for column etc basement slabs under ramed piles and mass concrete complete all as specified and directed.

M&L RCC work M-25 Design mix (using 20mm graded crushed stone aggregate) as in columns, pillars, piers posts and struts complete all as specified and directed.

M&L RCC work M-25 design mix (using 20mm graded crushed stone aggregate) as in beams, cantilevers bressumers, lintel over 1.5 mtr span complete all as specified and directed.

M&L RCC work M-25 design mix (using 20mm graded crushed stone aggregate) as in slab supported in walls cantilevers etc complete all as specified and directed.

M&L RCC work M-25 design mix (using 20mm graded crushed stone aggregate) as design mix as chajjas complete all as specified and directed.

M&L TMT bars, 10mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for column, hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per item No 12.00 above but 5mm to 10mm dia as in stirrups, spacers binders etc complete all as specified and directed.

M&L form work to side of concrete foundation, footing, bases of columns, raft and raft beams, sides and soffits (If any) of foundation and plinth beams and similar work, vertical or to batter complete all as specified and directed.

M&L form work to side of pillar posts struts piers columns etc. complete all as specified and directed.

M&L form work to sides and soffits of floor or roof beam, beam nauching, griders, bressum-mers lintels cantilevers, shelves including supprots, overhangs etc also splays between floors and beams etc complete all as specified and directed.

M&L form work as in suspended slab, such as roof slabs, floor slabs, landings and similar work, not exceeding 20mm thick (Horizonal or sloping) complete all as specified and directed.

M&L form work to chullah hoods, chajjas, throughs and similar items including edges complete all as specified and directed.

Treating the bottom and side of exc at the rate 5 ltr/sqm emulsion of surface area complete all as specified and directed.

Treating the backfil in contact with foundation at the rate of 7.5ltr/sqm emulsion of surface area complete all as specified and directed.

Treating the bottom surface of floor at the rate 5 ltr/sqm emulsion of surface area complete all as specified and directed.

Treating the ol under plinth protection at the frate of 5 Ltr/Sqm emulsiom of surface area complete all as specified and directed.

M&L 15mm thick screed bed on fair faces of concrete/brick surfaces in CM 1:4 with water proofing compound @ 3 % of wt of cement finished even and smooth in order to maintain proper slope over existing roof surfaces for laying APP based polymeric membrane finished complete all as specified and directed. (Polymeric membrane and WPC shall be meausred and paid seperately here-in-after).

Supply only integral water proofing compound.

M&L water proofing treatment to RCC roof slab including parapet comprising of following course of treatment/ specified from bottom to top (a) Applying bituminous primer 85/25 @ 0.40 Ltr per sqm over plastered surfaces of roof including parapet surfaces. (b) Over the priming coat laying one layer APP based polymeric membrane of approved manufacturer, 3 mm thick weight not less 3.6 Kgs/ Sqm and upper side of membrane thermally insulated with white mineral gravel finish, uniformly embedded during manufacturing process shall only be used, it shall be laid by torch application. side overlap should be 75mm and end shall be 100mm. For parapets, membrane shall be taken to a height of minimum 60cm and then inserted inside parapet in groove. The same shall be finished by a membrane flashing.

M&L two coat of reflective silver aluminium paint over APP membrane complete all as specified and directed.

M&L providing precast cement concrete (1:2:4) type B1, using 20mm graded crushed stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapits and railings upto 60cm in height, copings kneelers, apex stones, bed plates, kerbs not provided for in item No 04028 water throughs and the like including weathering slightly rounded or chamfered angles and throating as directed.

M&L brick work with fly ash 'brick straight or curved on plan exc 6m mean radius built cement mortar 1:6 complete all as specified and as directed.

M&L brick work with fly ash 'brick straight or curved on plan in any radius half brick thick wall built in cement mortar 1:4 complete all as specified and as directed.

M&L15mm thick rendering in cement mortar 1:4 on fair faces of brick work surace rendering is to be even and smooth with out using extra cenent complete all as specified and directed.

M&L15mm thick rendering in cement mortar 1:6 on other than fair faces of brick work surace rendering is to be even and smooth with out using extra cenent complete all as specified and directed.

M&L rough cast plaster on exterior walls applying the under coat of cement and sand mortar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm) mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even. The mix of cement and sand shall be slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered complete all as specified and directed.

M&L rendering 5mm thick in CM 1:3 on concrete ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 5mm thick in CM 1:4 on concrete surfaces such as beams, column etc finished even and smooth without using extra cement complete all as specified and directed.

M&L preparation of newly plasterd surface of wall and applying two coats cement base paint over a coat of primer complete all as specified and directed.

M&L preparation of old plasterd surface of wall and applying one coat cement base paint complete all as specified and directed.

M&L preparation of old plasterd surface of wall and applying two coats white wash complete all as specified and directed.

M&L preparation of newly plasterd surface of wall and applying three coats white wash complete all as specified and directed.

M&L preparation of newly plasterd surface of wall and applying two coats oil bound distemper over a coat of primer complete all as specified and directed.

M&L preparation of newly plastered surface of ceiling applying three coats of white wash complete all as specified and directed.

S&F steel window 1.25mm thick box type ERW hollow P section of size 60mm x 25mm single rebated comprise of gauged skelton shutter ERW size 50mm x 20mm and 1.25mm thick with two openable leaf consisting two Nos sash bars of T- section 20mm x 3mm welded to frame with one vertical mullion of ERW box type T- section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion with PCC (1:2:4) type B-1 (four Nos for each window) complete shown as per drg TD/2004/05 Sheet 2/2.

All as per item No 41.00 above but window with glazed shutter complete all as specified and directed.

S&F factory steel ventilator with top hung shutter incl hinges, peg stay complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.47mm nominal dia of wire and average width of aperture 1.38mm and fixed with tinned tacks, or galvanised wire staples to wooden / steel frames with beading complete all as specified & directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc 0.50 Sqm in each pane complete all as specified and directed.

S&F frame work such as grills, gratring etc with ends of bars shouldered or riveted or forged into spikes, framed guard bars, barred iron door ladder,frame balusters, walk ways, railing, frame work or water tanks & similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F factory made 30mm thick flush shutter, solid core construction, with block board core and plywood face panels, both face covered with decorative face veneer with lipping/frame to match commercial type on both sides with self closing circular knob for locking arrangement all as specified and directed.

S&F 35mm thick 2nd class hard wood factorymade panel shutter with lock rail & panel of 9mm BWP cmmercial ply seasoned & chemically pressured treated/12mm veneered , particle board with comercial veneering on both faces. The size of rail & steel as per IC: 1003(part-1) kiln seasoned & chemically pressure treated complete all as specified and directed.

M&L factory made 2nd class hard wood glazed and skelton door shutter made out of stiles & rails of 30mm thick 2nd class hard wood, klin seasoned and chemically pressure treated & open reabted and prepared to receive glass/gauge etc (without sash bars), edges of framing plain,chamfered of rounded, fitted with and mitred beads for securing glass etc compelte, the size of members of shutter shall be as per IS-1003. The shutter shall be fitted to the chowkhats complete all as specified and directed.

S&F preparation of new steel surface of any description over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

S&F preparation of old steel surface of any description over 10cm width or girth & applying one coat of synthetic enamel paint over a coat of primer complete all as specified and directed.

M&L preparation of newly wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint (of approved shade) over a coat of pink primer all as specified and directed.

M&L framed work as in doors or gates angle or other covering door, cooler stand etc to be prepared for handing or sliding with including either hooks and hinges or steel hanging dor fittings (exclusIve of steel or othr covering, running rails and guides) and hanging also fastening and fixing complete conforming to FE-290 Gde E-165.

M&L 75mm thick PCC 1:4:8 type D2 (using 40mm graded aggregate) as in foundation filling and mass concrete as floor sub base complete all as specified and directed.

M&L PCC 25mm thick 1:2:4 type B0 (using 12.5mm graded aggregate) as in floor as in levelling levelling course.

M&L machine cut kota stone flooring 18 to 20 mm thick over cement sreed beed 1:4, 20mm thick laid and jointed in grey cement slurry mixed with pigment to match the shed of the slab including rubbing polishing complete all as specified and as directed.

All as per item No 56.00 above but as in skirting over and including rendering 10mm thick cement mortar 1:4.

M&L non skid ceramic tiles (coloured) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but n exc 0.18 in floors etc. laid over 15 mm screed bed or bedding layer in CM 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile Complete all as specified and directed.

M&L glazed coloured ceramic tiles in vertical surface 300mm x 450mm x 7mm thick over 10 mm rendering in CM 1:4 and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified & directed.

M&L 75mm thick cement concrete 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in plinth protection path laid in panel surface finished even and fair using extra cement complete all as specified and as directed.

S&F factory made solid PVC moulded door shutters 28 to 30mm thick (stiles), with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plan colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, suppling & fixing in opening as per specification & drawing.

S&F exctruted aluminum alloy with galavanisied mild steel hing pin Butt hinges 100mm long complete all as specified and directed.

S&F aluminum anodised, barrel tower bolts of extruded section and fixed 150 mm long complete all as specified and directed.

S&F extruded aluminium alloy handles 150mm size fabricated type anodized ISI marked complete all as specified and directed.

S&F mild steel butt hinges medium weight colod rolled of size 100mm, ISI marked complete all as specified and directed.

S&F aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) 300mm long not less than 12mm dia with and incl minimum of 06 bolts and nuts, 4 on plate and 2 on staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, plate and fixed all as specified.

S&F aluminium anodised tower bolt 300mm long stove enamelled black with bright bolt & fixed complete all as specified and directed.

S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F in repair vitreous china squatting pan of Orrisa pattern size 580mmx440mm white with integral foot rest (excluding flushing cistern and flush pipe complete incluidng provision of lime concrete bedding complete all as specified and directed.

S&F PVC flushing cistern low level 10 ltr cap with inlet ball valve float and handle syphonic action type incl brackets and flush pipe of polythene of low or high density ISI marked complete all as specified and directed.

S&F tubes medium grade 'galvanised' with and including all fitting and fixed bore of 25 mm dia complete to walls and ceiling or laid in floor complete all as specified and directed.

S&F tubes medium grade 'galvanised' with and including all fitting and fixed bore of 15mm dia complete to walls and ceiling or laid in floors of 15mm bore complete all as specified and directed.

S&F in repair 15mm dia stop valve/angle valve of copper alloy fancy type chromium plated screwed down high pressure with crutch or butter fly handle screwed on both ends for iron pipe or for union complete all as specified and directed.

S&F 15 mm bore fancy type long body bib tap, half turn, with wall flange, cast copper alloy with capstan heads, chromium plated, screwed for iron pipe or for brass ferrule complete all as specified & as directed.

S&F swivel shower rose(fancy type) chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union all as specified and directed.

S&Fin repair vitreous china urinal half stall type white excluding flushing cistern , but including PTMT urinal spreader and waste pipe complete all as specified and directed

S&F WHB flat back of size 580mm x 450mm excluding taps waste chain plug stopper but incl brackets incl waste pipe cutting pinning in ends of brackets complete all as specified and directed.

S&F in repair 15mm dia bore cast copper alloy chromium plated fancy type pillar tap for with out cold & hot water complete all specified and as directed.

S&F 1000 Ltr capacity of rotational moulded polyethylen water storage tank (Cylindrical vertical with closed tap) hoisted and fixed in position including S&F 20mm float valeve 20mm dia GI pipe medium grade washout pipe 450mm long with plug and 20mm dia GI pipe medium grade overflow pipe 600 mm long with fitting and including dismantling of tank complete all as specified and as directed.

S&F ball valve brass high pressure with polythene float and fly nut screwed on iron pipe ad fixed 20 mm bore of pipe complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F brass chromium plated Tubular towel rail 20mm dia, 'D' type, 60cm long between flanges complete all as specified and directed.

S&F PVC (SWR) pipes of 75 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.8 mm) single socketed in any length with rubber ring joints laid in trenches or in floors of 75mm pipe complete all as specified and directed.

S&F PVC (SWR) pipes of 110 mm bore single socketed in any length fixed to wall complete all as specified and directed.

S&F PVC (SWR) floor trap, plain with grating including joining with solvent cement 75 mm dia complete all as specified and directed.

S&F PVC (SWR) bend 75mm bore of any radius complete all as specified and directed.

S&F PVC (SWR) bend 110 mm bore of any radius complete all as specified and directed.

S&F PVC (SWR)110mm branch piece (single 'Y' ) equal or unequal complete all as specified and directed.

S&F PVC(SWR) Vent Cowl complete all as specified and directed.

M&L 75mm thick PCC 1:4:8 type D2 (using 40mm graded aggregate) as in foundation filling and mass concrete as floor sub base complete all as specified and directed.

M&L machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade and fixed with grey cement and pigment over sand cussuion complete all as specified and directed.

M&L providing precast cement concrete (1:2:4) type B1, using 20mm graded crushed stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span,cills, steps, seismic and other similar bands, plinth courses, string courses , lacing courses, parapits and railings upto 60cm in height, copings kneelers, apex stones, bed plates, kerbs not provided for in item No 04028 water throughs and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L rendering 10mm thick in cement plaster 1:4 on surfaces on fair faces of brick work and surface finished even and smooth without using extra cement complete all as specified and directed.

M&L PCC 1:3 :6 type C2 using 40mm graded aggregate as in surface chanel and drain complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds mitred/stopped ends etc complete all as specified and directed.

M&L reinforced concrete pipes, class NP2, 300mm dia laid and jointed complete with collars complete all as specified and directed.

M&L PCC 1:2:4 Type B0 (using 20mm graded aggregate as) as in coping, roof curves, mud stops rounded or chamfered on edge complete all as specified and directed.

M&L reinforced concrete pipes, class NP-2, ISI marked, laid to slope in trenches, jointed and tested complete with collars for 150mm bore pipes complete all as specified and directed.

M&L PCC (1:4:8) type C-2, using 40 mm graded stone aggregate in bedding to drain pipes, including packing under and haunching against the sides of pipes tested complete for 150 mm bore concrete pipe complete all as specified and directed.

M&L rendering 10mm thick on fair faces of brick /concrete surfaces in cement mortar 1:4 complete all as specified and directed.

M&L cement concrete (1:2:4) type B-1, using 20 mm graded stone aggregate in surface channels of drains and benching including finishing the top of benching even and smooth using extra cement complete all as specified and directed. Notes :- Forming fair finished channel shall be measured and paid for separately.

M&L PCC (1:3:6) type C-1, using 20mm graded stone aggregate in coping complete all as specified and directed.

M&L precast reinforced cement concrete M-20 (Nominal mix using cement content 360 kg/cubic metre) using 20mm graded stone aggregate for manhole cover including placing in position and set in CM (1:4) complete all as specified and directed.

M&L construction of septic tank for 10 users designed to carry out sewage and sullage water , all as specified and shown on TD drawing No CEJZ/2002/TD/S2 sheet No 1/1 complete all as specified and directed.

M&L soakage well, excavation in any type of soil, foundation in PCC 1:3:6 walls of hony combed masonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of brick masonry in CM, RCC cover slab in M-25/SFRC cover, inter connecting pipes in RCC/DWC complete filled with brick bats of size 3 mtr dia and 3 mtr effective depth complete all as specified and directed.

Taking down chowkhat or frame exc 1.5 sqm each but n exc 4 sqm each (without taking off shutter from the franme) complete all as specified.

Racking out joints/pointing to random rubble or polygonal rubble uncoursed or brought up to course masonry built in cement mortar or cement lime mortar complete all as specified and directed.

Taking down cement or cement lime plaster, of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as directed and as specified.

Demolition of brick work/ stone boulder masonry work built in cement mortar including quoins, pillars etc complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling structurul steel work including doors, gates but excuding framed truss etc complete alla s specified and as directed.

Demolition cement concrete(unreinfored) as in ground floor and paving not exceeding 15cm thick below or above the ground level complete all as specified and directed.

Dismantling AC sheet roofing with ridge (corugated or semi corrugated)in roof covering complete all as specified.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws as specified.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws as specified.

S&F steel rolling shutter 1.25mm thickness of laths, with ball bearing as specified including top cover, anchoring rod and stapple and one shop coat of primer, erected in position as indicated complete with and including gear operated type bevel gear box and crank handle all as specified and directed.

M&L 100mm thick PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in floor laid in alternate panels, finishing the cement concrete surface even and smooth with out using extra cement complete all as specified and directed.

Forming 12mm thick expansion joints on 100mm thick concreet floor filled with bitumen mastic consisting 1 part of bitumen and 3 part of sand complete all as specified and directed.

Forming constuction (dummy) joints 65mm deep 10mm wide filled with bitumen mastic consisting 1 part of bitumen and 3 part of sand complete all as specified and directed.

S&F steel work in tubler trusss including special shaped washer etc using ERW or includuction butt weled tubes confirming to IS-1998 grade st 240 alk as specified and directed.

S&F hand rails, half round, flat section or other steel section drilled and counter shunk for blusters running bars for wind ties, door, balusters including securing bolts, including all necessary drilling, bolting riviting etc & similar work confirming to F-290 Gde E -165 complete all as specified and directed.

Hacking out old broken glass (any thickness, size or any description) complete all as specified.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane coplete all as specified.

Taking down carefully copper/aluminium point wiring for one light /socket/power point and taking down of teak wood batten/ PVC casing caping and making good disturbed surfaces of walls/ ceiling/ floors etc including dismentling of fittings complete all as specified.

M&L point wiring complete with 1.5 Sqmm single core multistranded copper conductor fire resistant low smoke & heat (FRLS) PVC insulated and unsheathed cable 1100 Volts grade confirming to IS-694 drawn through non metallic rigid PVC heavy duty conduit in concealed (min 20mm external dia) but shall be increased as per actual site requirement in accordance with clause No 19.125 of SSR Part-I, ISI marked with wall thickness not less than 1.8mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling including 1.5 mm FRLS PVC insulated unsheathed copper earth wire including sunken type pressed steel terminal boxes electro plated of suitable size with bakellite white/coloured top sheet cover 3.0 mm thick for one light point controlled by one way switch all as specified & directed. Note : The quoted rate shall be incuded cutting, chasing, making good of distrub surfaces including matching of existing colour surface of walls.

All as per serial item No 127.00 here-in-before but for one fan point controlled by one switch and regulator.

All as per serial item No 127.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per serial item No 127.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per serial item No 127.00 here-in-before but for one 3 pin socket outlet 15/16 Amps controlledby one 15/16 Amps switch on independent board with 2.50 Sqmm two single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour.

S&F switch piano flush type, single pole, one way, 5/6 Amp, 230 Volts complete all as specified and directed.

S&F switch piano flush type, single pole, one way, 15 Amp, 230 Volts complete all as specified and directed.

S&F socket outlet for 3 pin (with 2 pin outlet also), 5/6 Amp, flush type 240 Volt complete all as specified and directed.

S&F socket outlet for 2 in 1, 3 pin 5 & 15 Amp, flush type 240 Volt complete all as specified and directed.

S&F ceiling rose surface bakelite 65 x 50mm two or three terminals complete all as specified and directed.

S&F decorative ultra slim liner LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient suitable for 16 Watt to 20 Watt with LED tube of model E-LITE LED Pride Plus and connecting up with and including three core, PVC insulated, sheathed copper conductore cable of required size and length from ceiling rose to fitting complete all as specified & directed.

S&F new fan regulators electronic step up type socket size and connecting up, ISI marked flush type, 240 Volts complete all as specified and directed.

S&F LED type street DRACO Series light luminaire 20 watt 230 V 50 Hz including all necessary fitting accessories and LED complete, all as specified & directed.

S&F sheet metal enclosures, double door type, suitable for fixing MCB SPN with 200 Amps rated bus bar, 8 way, 240 volts complete all as specified and directed.

S&F sheet metal enclosures, double door type, suitable for fixing TPN with 200 Amps rated bus bar, vertical DB 4 way, 415 volts complete all as specified and directed.

S&F MCB 63 Amp, triple pole & neutral, 415 Volts complete all as specified and directed.

S&F MCB 32/40 Amps, single pole & neutral, 240 Volts, 'C' curve, 10KA, ISI marked as per IS/IEC 60898-1 2002, Ingerted label holder, sliding bottom clamp improved air channels, colorb coded On/Off indication on dolly IP 20 protected terminals, DC-80V per Pole-1KA complete all as specified and directed.

S&F MCB 6-40 Amps, single pole, 240 Volts, 'C' curve, 10KA, ISI marked as per IS/IEC 60898-1 2002, Ingerted label holder, sliding bottom clamp improved air channels, colorb coded On/Off indication on dolly IP 20 protected terminals, DC-80V per Pole-1KA complete all as specified and directed.

S&F 2nd class hard wood rectangular block open recessed of size 30 x 25 x 5cm depth with 3mm thick phenolic laminated sheet top cover fixed with suitable steel screws & PVC rawl plug (4 Nos), complete all as specified and directed.

Supply, laying, jointing and testing XLPE insulated, armoured, heavy duty LT underground electric cable with stranded aluminium conductor 1100 volts grade cross sectional area 10 sqmm 2 core laid in trenches, along poles through pipes etc complete all as specified & as directed. (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately including taking down old unserviceable XLPE cable. (ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.

Supply, laying, jointing and testing XLPE insulated, armoured, heavy duty LT underground electric cable with stranded aluminium conductor 1100 volts grade cross sectional area 25 sqmm 4 core laid in trenches, along poles through pipes etc complete all as specified & as directed. (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately including taking down old unserviceable XLPE cable. (ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.

Excavation in trenches not exceeding 1.50m wide and not exc 1.50m in depth and getting out in soft / loose soil complete all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers n.exc. 25cm deep as in soft/loose soil copletete all as specified.

Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5 m above the starting point.

M&L brick work with fly ash bricks {As per IS-13757 (1993) burnt clay fly ash building bricks}, (Old size bricks) with width equal to the length of the brick laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection complete all as specified & directed.

M&L dry sand (tibba sand) and punning for cushioning to under ground cable all as directed. Note : For the purpose of payment only punned thickness shall be measured.

M&L galvanised iron pipe light grade of 40mm bore for protection fo LT cable fixed to walls/poles/road crossing including clamps complete.

S&F sub main wiring on including passing throuh PVC conduit pipe 1100 volts grade with PVC flexible cable copper conductor unsheathed multistranded single core of size 6 Sqmm and continuous earth with PVC flexible cable copper conductor unsheathed multistranded single core of size 6 sqmm of green colour confirming to IS 694/1990 including taking down existing unserviceable sub main wiring. (Note : Two runs of cable with one run of earth wire and one run of PVC casing caping should measured as one length).

S&F ceiling fan 5 star rating complete of 1200mm sweep 240 Volts, 50 Hz, AC supply with down rod & canopy including provision of fan hook in ceiling for fixing of ceiling fan including necessary electric connection with 1 Sqmm, three core, flexible copper multistranded conductor cable all as directed.

S&F Voltage Stabilizer of capacity 1 KVA for automatic operation, Single Phase, naturally air cooled, indoor type, designed for input variation between 170 Volt to 250 Volt and with output voltage stabilized at 230 Volt with accuracy of ± 2.5% and connecting up all as per manufacturer’s instructions & as directed. Make :- Brentford / Vinus / AE / Vinitec / V-Guard / Power Tech / ITE, Gurgoan / Volina / Blue Line

Supply only desert cooler in steel body with tank capacity of 120 Ltr, propeller type cooler fan with motor (ISI Marked) three speed 1440 RPM, 1/8 HP Copper winding, 230V, 50HZ, sealed double ball bearing, vacuum impregnated strator winding, One Year Warranty, silent operation, nominal capacity 4000 cum/hr, fan size 450mm, type of blade metallic (HIP), submersible water pump, filter pad, electric driven, single phase, 230 volts, 50 Hz, capacitor 4 mfd, suitable plug top 5/15 Amp including all accessories complete all as specified & directed by Engr-in-Charge. Make : Bajaj/ Khaitan / Crompton. Note :- (i) Filter panels,front grill and top of the cooler body shall be made of 1mm galvanized steel sheet. The sump tank and rest of the body shall be made of 1.20mm thick galvanized steel sheet. The galvanised steel sheet shall be ISI marked and shall have zinc coating not less than 100 gms/sqm and shall conform to IS : 277. (ii) All internal surface including inside of the tank, fan blades, motor body, pump, pump body shall be painted with water resistant paint conforming to IS: 986. The outer surface of the cooler shall be spary painted with synthetic enamel paint of approved shade/tint. (iii) The desert cooler shall be fitted with adjustable grill with separate on/off switch of 5/6 Amp rating (ISI Marked) for cooler fan and water pump and three stage speed regulator (Low, Medium, High) for three speed cooler fan motor. (iv) Suitable nylon bushes shall be provided in the grill for easy and smooth movement of louvers. (v) The filter pads shall be contain wood wool.The filters pads shall be fixed over the panel and seured by clamping guard of galvanized wire of 2mm dia (approx) squre/rectangular.The wire guard shall be fixed in the clamps to avoid any sagging.

Supply and installation Water Cooler, storage capacity 80 litre, nominal cooling capacity 40 litre per hour, Partial Stainless Steel (PSS), electric driven, single phase, 230 Volt, 50 Hz, hermetic type compressor with suction gas cooled motor equipped with overload protector, propeller type (Quiet) condenser fan, automatically controls temperature thermostat, 02 Nos cold water taps, complete, all as specified. Make : Voltas / Blue Star / Usha Shriram

Supply, installation & testing of geyser (water storage type) of capacity 25 litre vertical mounting type, suitable for 230V, SP, 50 Hz AC supply fixed with & including ‘Anchor’ type /fastener type bolts & nuts (Set of 4 bolts of 10mm dia 150mm long with nuts & washers) into the wall grouted properly to hold the geyser and making good the disturbed surface as original all as per manufacturer’s instructions & as directed. Make :- Bajaj / Crompton Greaves / Usha Lexus / Venus / Racold.

M&L earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/ equipment and testing on including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25mm x 3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & as directed.

Akhil Enterprises

Singh Associates

M/s S Amarjit Singh