SPECIAL REPAIR TO CERTAIN SMQS AT AF STN PALAM UNDER GE (AF) PALAM, DELHI CANTT-10

Supply & Fixing of Thermoplastic (Polycarbonate/Polystyrene), IP65 as per IEC 60529, corrosion proof, suitable for Meter box lid screws made of stainless steel V2A, internally embedded gasket for lid and enclosures, metric size knock outs for cable entry from top and bottom with transparent Hinged lid . DB should be able to adapt any make of MCB or din mountable equipement and tested as per as IEC 61439-3, fit for the new standard IEC 60 364-4-41, glow wire test IEC 695-2-11: 750C, flame retardant , self -extinguishing protection against mechanical load IK 08 (5 Joule) in accordance with IEC 62262 and enclo

Taking down Chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sqm but n exc 4 Sqm each and credited to the contractor complete all as specified and directed by Engineer-in-Charge. Note: The damaged portion of the tiles/rendering shall be made good with the same material to match with the adjacent surface.

Taking down shutters of any description exc 1 Sqm and not exc 2 Sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description n exc 1 Sqm each complete all as specified and directed by Engineer-in-Charge.

Refixing of Shutters after easing and adjusting also refixing builders hardware as required including renewal of unserviceable screws, etc of any description exc 1 sqm and n. exc. 2 sqm each in same opening, complete all as specified and directed by Engineer-in-Charge.

Refixing of Shutters after easing and adjusting also refixing builders hardware as required including renewal of unserviceable screws, etc of any description n.exc 1 sq. m each in same opening, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 10mm thick plaster on fair faces of brickwork or concrete surfaces in cement mortar 1:3 in ceilings, to be finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Supply laying, connecting and testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, of size 50 sqmm 3.5 core laind in trenches or passing through pips/ ducts complete all as specified and directed by Engineer in charge.

sure dimension should be 217x253x115mm (LxBxH) complete all as specified and directed by Engineer-in-Charge.

Material & Labour for preparation of new plaster surface of walls ,chajjas, soffits & beam including necessary scaffolding and applying applying complete with two or more coats of acrylic smooth exterior paint of required shade @ 1.43ltr/10sqm over a coat of exterior primer @ 2.20kg/sqm complete all as per manufacturers instructions and as specified and directed.

Supply and fixing of DWC HDPE tubing 90 mm OD and 75 mm ID including all fitting/fixtures such as Tee/Elbow/Socket/ Nipple etc.Conforming to IS 16205 bore for laying cable, cut to size and making the tubing for cable protection along with drawn in cable into the HDPE tubing on the surface/on the wall /along drainage etc complete all as specified and directed by Engr-in-Charge.

Supply & Fixing for Factory made 35mm thick flush shutter solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frames) n exc. 1.5 sqm each and credited to the contractor complete all as specified and directed by Engineer-in-Charge. Note: The damaged portion of the tiles/rendering shall be made good with the same material to match with the adjacent surface.

Supply & Fixing for Pressed steel frames, with size of frame 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates hold fasts etc and applying a coat of red oxide primer including providing PCC 1:3 :6 type C-0 using 12.5 mm graded crush stone aggregate for filling back of chowkhats complete all as specified and as directed by the Engineer-in-Charge.

Supply & Fixing Pressed steel frames , with size of frame 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates, hold fasts etc and applying a coat of red oxide primer including providing PCC 1:3 :6 type C-0 using 12.5 mm graded crush stone aggregate for filling back of chowkhats, complete all as specified and as directed by the Engineer-in-Charge .

Material & Labour for preparing new plastered or unplastered surfaces on walls including brooming down or steel wire brushing, scraping down and applying wall putty average 3 mm thick, and applying two coats of distemper oil emulsion over one coat of alkalic resistant primer complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing factory made 5 mm thick PVC sheet of density 600 kg/cum manufactured by an ISO 900-2008 certified company, plain 5 mm thick PVC sheet panelling for back side (wall side) and also manufactures test report and test certificate is mandatory with each and every supply of material including taking down of exiting back side (wall side) or any kind of PL board or plyboard complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in repair 18/19 mm thick Block boards, grade 2 quality, interior grade, commercial type, fixed with timber frame-work with screws in Kitchen drawers, Cupboard shutters etc complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 0.90 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Factory made wire gauzed PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panel will be of wire gauze . The wire gauze shall be wrapped on an additional square 8 mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly at site as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

Removal of excavated surplus soil to a distance not exc. 50 Mtrs and depositing where directed at a level not exc 1.5 Mtr above the starting point complete all as s

Supply & Fixing Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws complete all as specified and directed by Engineer-in-Charge. (Note: stainless steel butt hinges and necessary SS screws shall be paid separately).

Supply & Fixing 40 mm dia, cupboard knobs fixed with nut, screw and washer of brass polished complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Stainless steel basket with roller( size as per ground requirement) for kitchen cabinet complete all as specified and directed.

Supply & Fixing Stainless steel Hydraulic hinges fixed with stainless steel screw (size as per ground requirement) complete all as specified and directed.

Supply & Fixing for Aluminium alloy, anodised, sliding door bolt 300mm length with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing for 150 mm long Aluminium anodised,handle of extruded section fabricated type anodised and fixed complete all as specified and directed.

Supply & Fixing for Aluminium, anodised, barrel tower bolts 150 mm size of extruded section, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 125 mm long Aluminium anodised,handle of extruded section fabricated type anodised and fixed complete all as specified and directed.

Supply & Fixing for Aluminium, anodised, barrel tower bolts 125mm size of extruded section, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing for Butt hinges, medium weight, cold rolled mild steel 100mm size, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing door strip comprising of aluminium holds & rubber strip fixed at bottom of door shutter with screws, length upto 1.2m each strip complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 45x70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed Stainless steel screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/sqmm, modules of elasticity 900 N/sqmm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/ stainless steel dash fasteners of required dia and length complete all as specified and directed by Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Taking down steel window and ventilator (without taking off shutters from the frames) including grills etc and removing from site and making good the disturbed portion in CM 1:3 or PCC 1: 2:4 type B-1 complete all as specified and directed by Engineer-in-Charge. Note: The damaged portion of the tiles / rendering shall be made good with the same material to match with the adjacent surface.

Supply & Fixing Hasp & Staple, 125 size, safety type aluminium anodised with mild steel hinge pin including bolt, to hinge plate and fixed with screws, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Continuous (piano) hinges, 30mm width of flaps when open, Stainless steel, bright finish or electrogalvanised, complete all as specified and directed by Engineer-in-Charge.

terial & Labour for Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.0 mm thick, burried directly in ground vertically to a depth not less than 2.25 m below the ground level with top edge of earth plate at a depth not less than 1.50 m below ground level. Earthing plate surrounded by 15cm thick packed alternative layers of charcoal dust and common salt, connected with GI wire of dia 4mm by means of bolts, nuts, check nuts and washers of galvanised iron with thimbles at one end and the other end connected to main switch board and protected by 40mm dia bore medium grade GI pipe. Provision of 20mm dia bore light grade GI pipe for watering including GI funnel and wire mesh. The pipe shall be provided vertically upto top level of earthing pit and then taken horizontally to the equipment. Provisionn of cement concrete chamber of iinternal size 300x300x300mm with PCC (1:3:6 ) type C-2 (using 40 mm graded stone aggregate), constructed at 1.00 m metre away from edge of earthing pit with 50 mm thick precast RCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) reinforced with 8mm dia TMT bars @ 150mm C/C including all necessary earthwork in soft / loose soil complete all as specified and shown in Electrical Plate No. 3 of SSR Part-1 (2009) and directed by Engr-in-Charge. Note: (a) The unit rate includes earthing strip and protection pipe upto maximum 7.5 metre from earth plate, earth point / test point. (b) On testing after completion, if the desired earth resistance is not obtained, the earthing will be redone at no extra cost.

Material & Labour for preparation of new or previously untreated wood and wood based surfaces of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for preparation of old painted surfaces of wood and wood based material of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing sheet glass 3 mm thick, ordinary quality and glazing with oil putty / wooden beads in square or rectangular in section n exc 0.5 sq.m in each pane complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass, any thickness, size, quality, or description from wooden/metal frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete upto 4th storey complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing rolled mild steel grade Fe-290 Gde-E-165 as in Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing factory made 18 mm (+0.7mm thick celuka PVC board of density 600 kg/cum manufactured by an ISO 900-2008 certified company having one side perlaminated and other side plain fixed as in cabinet/ cupboard shutters including providing manufactures test report and test certificate is mandatory with each and every supply of material including taking down of existing shutter or any kind of PL board or plyboard complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing factory made 18 mm (+0.7mm) thick celuka PVC board of density 600 kg/cum manufactured by an ISO 900-2008 certified company fixed as in shelves perlaminated/ cabinet/cupboard drawers including providing manufactures test report and test certificate is mandatory with each and every supply of material including taking down of existing Shelves or any kind of PL board or plyboard complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing sheet glass 5.5mm thick, ordinary quality and glazing with oil putty, wooden beads and aluminium beading in square or rectangular in section n exc 0.5 sq.m in each pane complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in repairs Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Figured Glass pin head type 5mm thick n exc 0.5 Sqm and glazing with oil putty, Complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 50mm magnetic catches with brass body and striking plate including letting in as fixed, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Floor door stopper of aluminium alloy body 140 mm cover plate and toungue, anodised with hard drawn steel spring fixed in floor, complete all as specified and as directed by Engineer-in-Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed by Engineer-in-Charge.

Demolition of reinforced cement concrete of any description if cement concrete is reinforced (reinforcement cut as required to facilitate demolition) in any position not otherwise specifically provided for, Complete all as specified and directed by Engineer-in-Charge

Supply & Fixing mild Steel ordinary rat tail rod pattern springs including roller and roller plate 300 mm length, complete all as specified and directed by Engineer-in-Charge.

pecified and as directed by Engr-in-charge.

Supply & Fixing Brass door magic eye, as per given specification : material : resin lens + zinc alloy,T top diameter : 31.2 mm, Bottom diameter: approx 24mm, pipe

diameter: approx 16mm, total length :approx 50mm, inner height :approx 36mm, application : 35 to 60mm thick, viewing angle 200 degree all round and clear view of 200 degree of surrounding without opening the door –unique design , ultra clear view and superior finish , wide angle, best in class lens for all round visibility , such that the outsider cannot hide anywhere, the back cover protects you from the outsider observing any movements inside, easy to install with inbuilt screw over a wide range of door thickness from 35mm to 60 mm etc required at site complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing aluminium Drapery rod, 25 mm dia , not less than 1mm thick, coated finish including teak wood brackets & end knob as required with teak wooden curtain rings etc complete all as specified and directed by Engineer-in-Charge (Min 2 Nos brackets ,02 Nos End knob ,12 Nos Rings for each door/ window).

Supply & Fixing Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing for stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

Material & Labour for 2nd class hardwood Handrails Size 75×60mm rounded or shaped with splayed faces in straight lengths and fixed complete all as specified and directed by Engineer-in-Charge.

Material & Labour for joint free non skid coloured ceramic tiles, 7 to 8mm thick (squre or rectangular) area of each tile n.exc. 0.11sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces, laid over & including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing aluminium frame for doors, windows, ventilators, Powder Coated of any colour (minimum thickness of powder coating 50 micron), with one or more rebates including joining cleat for fixing Window / ventilators frames shall be fixed to brick / concrete masonry by using nylon self expansion caps & 75/100 mm MS screws after drilling in walls.. complete all as specified and as directed by Engineer-in-Charge. NOTE:- The weight for all necessary fitting such as cleats, glazing clips, rubber packing/ PVC item/raw plug material/bass screw etc which are required for fabrication shall not be included in the weight of aluminium for the payment, the weight of aluminium section shall be considered only, no extra payment for fabrication material sahll be allowed.

Material & Labour for GI tube light grade of bore 50 mm with all fittings and fixed complete to walls and ceiling or laid in floor for cable crossing including cutting of bitumen roads/PCC and making good after laying of cable up to building height complete all as specified and directed by Engineer-in-Charge.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for fair finish

ed surface; not exceeding 200mm thick (Horizontal or sloping), complete all as specified and directed by Engineer-in-Charge.

Material & Labour for RCC, Type B-1 1:2:4 (using 20 mm graded stone aggregate) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for special treatment for sunken portion of WCs/Bath & toilet etc executed in following stages : Stage 1: Providing 15mm thick plaster in CM 1:3 mixed with water proofing chemical of Dr.Fixit or Shalicrete 'R' of STP Ltd in the proportion/quantity all as per manufacturer's instructions. State 2 : Primer-Mix Tarfelt LM of STP Ltd (diluted with water in ratio 1:1) @ 250 gms/sqm and apply the primer on the plastered surfaces. Stage 3 : Application of 1st coat of Tarfelt LM of STP Ltd (without dilution with water) @ 1Kg/Sqm by brush all as per manufactuer's instructions. Stage 4: Laying fyber glass cloth (weight not less than 50gram/ Sqm) over the 1st coat while the coated surface is still sticky. Stage 5: After 6 to 7 hours interval, apply second coat i.e. final coat of Tarfet LM of STP Ltd (without Dilution with water) @ 1kg/ Sqm by brush as per manufacturer's instructions. Stage 6: Providing 10mm thick protective plaster in CM 1:3 mixed with STP No. 1 @ 250ml/50 Kg cement all as per manufacturer's instructions. Stage 7: Carryout ponding test for 48 hours to ensure water tightness of repaired sunken portion. NOTES:- (i) Mode of measurement: Actual area treated (floor and adjoining walls) will be measured and paid .

Material & Labour for Coloured Glazed ceramic tiles in vertical surface 450X300x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including rendering 10mm thick in CM 1:4 on fair faces of brickwork or concrete surfaces as backing coat complete all as specified and directed by Engineer-in-Charge.

Dismantling water tank of capacity exc. 250 ltr and n. exc. 500 ltr and removing to store complete all as specified and directed by Engineer-in-Charge.

Material & Labour for cement concrete type E-2 1:5:10 (using 40mm graded crushed stone aggregate) in foundations, mass concrete and filling in sunken floor etc complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing for ball brass valves, 20 mm bore, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

Material & Labour PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in roof kerbs, benching etc including weathering, slightly, rounded or chamfered angle and throating complete all as specified and directed by Engineer-in-Charge.

Material & Labour for cement concrete tiles 30cm x 30cm x 20mm thick machine pressed, set & pointed in neat cement slurry in floor with grey cement and no pigment and cut and polished on roof over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing of auto closing hinges openable at 0 degree for cabinet shutters complete all as specified and directed by Engineer-in-Charge.

Material & Labour for brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 Complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing framed work for cooler stand /doors or gates of angle iron fixed with window upto two storey bldg including100X100X100 mm cutting brick work /stone masonry/ cement concrete & filling with PCC 1:2:4 & making good complete all as specified and directed by Engineer-in-Charge.

Rooting out trees, flora & fauna and foliage as grown on RCC roof surfaces and brick/stone walls by cutting hole into slabs/walls for digging out roots and using chemical to burn deep rooted tree roots etc and making good disturbed portion of wall/roof with cement concrete 1:2:4 type B-1 complete all as specified and directed by Engineer-in-Charge.

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 500 litres capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed by Engineer-in-Charge.

Disconnecting existing water tank exc. 500 litres but n.exc 1000 litres capacity in any position, setting aside for repairs, cleaning and removing all scales, dirts etc from tank and mouth of circulating pipes etc and re-fixing in position complete all as specified and directed by Engineer-in-charge.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed by Engineer-in-Charge.

Material & Labour for preparing plastered or unplastered new surfaces on ceilings including brooming down or steel wire brushing, scraping down and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

Material & Labour for brickwork with sub-class `B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for machine cut kota stone slab 18-22 mm thick as in floor /staircase riser & traider (one piece) ,vertical surfaces/skirting etc ,set and jointed with grey cement slurry mixed with pigment to match the shade of slab, size of slab exceeding 0.11 sqm but n.exc. 0.36 sqm including provision of screed bed 15 mm thick in cement mortar 1: 4 and a coat of cement slurry @ 3 kg/sqm including rubbing/grinding and beeswax polishing etc complete all specified. Note:- (a) Rates also includes rounding of edges for traider staircase in this item for necessary raking, circular cutting or notching and waste on stone etc. (b) kota stone will be provided Single piece in each riser & traider .

Material & Labour for Antitermite Treatment of wood work such as chowkhat or shutters At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same with putting complete all as specified and as directed by Engineer-in-Charge.

Dismantling of Stone slabs and tiles of any description or thickness in floors aprons etc laid in cement mortar of any thickness, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for preparation of new or previously untreated surfaces of steel of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over & incl one coat of red oxide primer complete all as specified and as directed.

Material & Labour for preparing old surfaces on ceilings including brooming down or steel wire brushing, scraping down and applying two coats of white wash complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 15 mm thick cement plaster on fair faces of brickwork or concrete surfaces in cement mortar 1:6, to be finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material & Labour for preparation of old painted surfaces of steel and iron surfaces of any description not otherwise described over 10 cm width & girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Material & Labour for washed stone grit plaster (of any colour/ pattern) on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 coloured stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and directed by Engr-in-Charge. (Note :- Payment for providing grooves shall be measured and paid separately).

Taking up or down steel water tubing 15mm bore and connection complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing GI tubes 15 mm bore 'medium grade' with all fittings and fixed complete to walls and ceilings or laid in trenches or cutting chases in wall and making good to disturbed portion of wall complete all as specified and directed by Engineer-in-Charge.

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete all as specified and directed by Engineer-in-Charge.

Refixing of old steel tubing and connection in new or old position of 15mm bore. complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 18- 20mm thick granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including cutting for hole, rounding of edges and mirror polishing over and including 15mm thick screed bed in cm 1:4, complete all as specified and directed by Engineer-in-Charge. Note:- (a) Rates also includes in this item for necessary raking, drilling /circular cutting or notching and waste on Granite. (b) Shade/coloured /pattern /fixing design shall be approved by GE / Engineer-in-Charge.

Taking up or down steel water tubing and connection complete 20 mm bore complete all as specified and directed by Engineer-in-Charge.

Material & Labour for MS TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooking for columns, hooking ends and binding with and including mils steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-in-Charge.

Supply only Integral Water Proofing compound complete all as specified and directed by Engineer-in-Charge.

All as per description of item No 77.00 here-in-before but except bricks complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar 1:4, to be finished even and fair with water proofing compound by weight as per manufacturer's instructions, including necessary scaffolding up to (G+3 storey) complete all as specified and directed by Engineer-in-Charge. Note : WPC will be paid separately.

Refixing old GI tubing and connections, 20 mm dia, in old or new position. (Walls, ceiling, f

Supply & Fixing in repairs PVC valveless, syphonic action type, flushing cistern (Twin fush type), low level 10 ltr capacity, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed by Engineer-in-Charge.

loors, etc.) complete all as specified and directed by Engineer-in-Charge.

Material & Labour for repair work of existing terrazzo topping tiles and Kota stone etc including grinding and beeswax polishing in floors, skirting, dado etc, with admixture of pigment to match the shade complete all as specified and as directed by Engr-in-Charge. Note: (i) Rates deemed to include for necessary replacement of terrazzo topping tiles and Kota stone slab etc which are required for repair of existing floor, no extra payment for utilized material in repair work in floor shall be made. (ii) Mode of measurement: Actual area grinding with beeswax polishing with repair (floor and adjoining walls) will be measured and paid.

Supply & Fixing in repairs vitreous china squatting pan, 'Orissa' pattern, size 580 X 440mm white with integral foot rests, including connection to drain or outgoing pipe and to flushing pipe, antisyphonage pipe joint and to socket or stopper, including flush pipe all fittings etc complete all as specified and directed.

Supply & Fixing in repairs CP angle/stop valve of cast copper alloy screwed down high pressure with capstain head screwed both ends for iron pipe or for unions and fixed 15 mm bore complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in repairs CP shower roses with CP Arms, 15mm bore, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in repairs colour vitreous china ware Wash Hand Basin, of Min size 550 x 400 mm including brackets, cutting for and pinning in ends of brackets or erecting stand including bottle trap chromium plated heavy duty 32 mm dia with all fittings etc complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including brackets, cutting for and pinning in ends of brackets or erecting stand including brass CP union/waste fitting of 32mm dia and discharge pipe of 32mm dia PVC of 1.0 m length , with all fittings etc complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in repairs 15mm dia Brass CP wall mixer for mixing hot & cold water fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in repair 15mm dia Brass CP Sink mixer (wall mounted) swan Neck type with for mixing hot & cold water complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in repair 15mm dia Brass CP central hole basin mixer with 450mm braided connection pipe (without pop-up) for mixing hot & cold water, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in repairs 15 mm bore bib tap long body chromium plated , fancy type, cast copper alloy with capstain head screwed down screwed for iron pipe or for brass ferrule fancy type complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Brass chromium plated, tubular towel rails 20 mm dia, D- type, 60 cm long between flanges complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in repair Soap dish, brass CP any type, fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 60 cm long glass self assembly consisting of 5.50 mm thick glass shelf 12 cm wide with chromium plated bracket guards and railing screws complete all as specified and directed by Engineer-in-Charge.

Taking down AC, PVC pipes of 100/110mm dia of any description including all fittings complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls and floors including suitable clamps at one meter of interval including material and labour for necessary scaffolding and formwork (G+3 storeys) and safety arrangement complete all as specified and directed.

Taking down CI pipes of 100/110mm dia of any description including all fittings complete all as specified and directed by Engineer-in-Charge.

Taking down CI pipes of 75/80 mm dia of any description including all fittings complete all as specified and directed by Engineer-in-Charge.

All as per item 125.00 here-in-before but refixing of old pipes (Except pipes) complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing for PVC (SWR) bends of radius, suitable for 110mm dia PVC pipes fixed complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing for 100mm bore cast iron waste and vent pipe in any length with or without ears fixed to walls with Pig lead joints fixed to wall including suitable clamps after every one mtr of interval complete all as specified and directed

Supply & Fixing for 75mm bore cast iron waste and vent pipe in any length with or without ears fixed to walls including suitable clamps after every one mtr of interval with Pig lead joints fixed to wall complete all as specified and directed.

All as per item 128.00 here-in-before but refixing of old pipes (Except pipes) complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing for CI 100mm bends with door complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing for CI 100mm single branch piece with door complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing for CI 75mm bends with door complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing for cast iron cowls 100 mm size complete all as specified and directed by Engineer-in-Charge.

Material & Labour in repairs for cast iron Nahani trap/floor trap with CP grating including jointing with Pig lead joint to waste pipe of 75mm dia fixed in cement concrete type B-1(1:2:4) complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in repairs for Cast Iron `P /S Trap 100mm bore complete all as specified and directed by Engineer-in-Charge.

Returning, filling in including spreading, leveling watering and well ramming in layers not exceeding 25 centimetre in soft/loose soil complete all as specified and as directed.

Supply & Fixing in repairs, salt glazed stone ware gulley traps 150x150mm size square mouthed type ‘P’ including CI cover complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre depth for foundation, manhole etc not exc 10 Sqm on plan and not exc 1.5 metre in depth including getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Removing excavated surplus soil/material not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed.

Demolition and breaking up drain pipes (slat glazed ware, AC or reinforced concrete any type) set in cement mortar, in 150 mm internal dia complete all as specified and as directed.

Material & Labour Plain cement concrete 1:3:6 type C-2 using 20 mm graded stone aggregate as in surface channel, drain and manholes complete all as specified and as directed.

Material & Labour reinforced concrete pipes, class NP2, 150 mm bore, laid and jointed complete with collars complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete from sunken floor, roofs, floors (other than ground floor hacking of surfaces after cleaning with wire brush (floor and adjoining wall) and disposing off debris outside MoD land complete all as specified and directed by Engineer-in-Charge.

Material & Labour 150 mm thick Concrete bed to drain pipes in cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and as directed.

Material & Labour Precast cement concrete PCC 1:2:4 type B-1 (20mm graded aggregate) CM 1:4 in landing cover slab,drain and manhloe cover ,shelves troughs and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 75 mm thick cement concrete type D2, 1:4:8 (using 40 mm graded aggregate) as in sub base, to be finished even and fair complete including use of necessary form work complete all as specified and directed by Engineer-in-Charge.

Taking down carefully copper/aluminium point wiring light ,fan, light fittings,socket or power complete, such as switches, ceiling roses, pendents, regulators, sockets etc.removing materials to store for keeping in safe costudy or for taking credit (credit for above items should be made as per conditioned separately) and making good disturbed surface of walls, floors etc. complete all as specified and directed by Engineer-in-Charge.

Material & Labour for point wiring with single core PVC insulated but sheathed 1.5 sqmm FRLS multistranded copper conductor FRLS cable 1100 volt grade IS-694 marked concealed conduit wiring drawn in and including rigid non metallic PVC conduit not less than 20mm dia ISI marked medium grade with all conduit fittings and fixing accessories including sunken anodized pressed steel terminals boxes 2mm thick cover with 3mm thick plastic laminated white sheet cover for mounting switches, sockets, fan regulators , etc and single core PVC insulated and sheathed 1.5 sqmm FRLS multistrand copper conductor cable 1100 volts grade IS-694 as continous earth wire connecting to common earth dolly complete for following all as specified and directed by Engr-in-Charge for the following :- .

Supply & Fixing for machine pressed precast concrete interlocking paver block any shape and size,with grey cement and pigment to match, confirming to IS 15658-2006 of 60mm thick M-35 grade laid over 50 mm thick sand cushioning complete all as specified and directed by Engineer-in-Charge.

Removing demolished materials etc (other than spoil) to a distance exc 1.00 KM and n exc 1.50 KM including loading, unloading and stacking etc complete all as specified and directed by Engineer-in-Charge.

One light point controlled by one switch one way complete all as specified and directed by Engineer-in-Charge.

One fan/exhaust fan point controlled by one switch complete all as specified and directed by Engineer-in-Charge.

One 3 pin 5 Amps socket out let point on the same board controlled by one switch complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing front glass shelf double 60cm long 5.5 mm thick glass with CP fame with bracket fixed in wall complete all as specified and directed by Engineer-in-Charge.

Material & Labour for point wiring with single core PVC insulated but sheathed 2.5 sqmm FRLS multistranded copper conductor FRLS cable 1100 volt grade IS-694 marked concealed conduit wiring drawn in and including rigid non metallic PVC conduit not less than 20mm dia ISI marked medium grade with all conduit fittings and fixing accessories including sunken anodized pressed steel terminals boxes 2mm thick cover with 3mm thick plastic laminated white sheet cover for mounting 15 Amp Socket outlet and switche etc and earth wire single core PVC insulated but unsheathed multistranded copper conductor cable 1100 volts grade IS-694 marked 2.5 sqmm FRLS cable as continous earth wire connectings to common earth dolly complete all as specified and directed by Engr-in-Charge.

Supply and fixing for switch piano flush type 5 Amps, single pole one way complete, all as specified and directed by Engr-in-Charge.

Supply and fixing for socket out let 3 pin 5 Amps, flush type complete, all as specified and directed by Engr-in-Charge.

Supply & Fixing switch piano flush button single pole one way 15 Amp complete , all as specified and directed by Engr-in-Charge.

Supply & Fixing socket outlet 2 in 1, 6 pin 5 Amp and 15 Amp flush type universal complete , all as specified and as directed by Engr-in-Charge.

Supply and fixing stepped type electronic fan regulator 300 watt, 230 volts, 50 HZ, AC. Supply complete all as specified and as directed by Engr-in-Charge.

Supply and fixing for lamp holder, PVC/poleycarbonate type, insulated body with back plate of batten fitting complete all as specified and as directed by Engr-in-Charge.

Supply and fixing of LED bulb 7 watt fixed in pendent holder /bulk head complete all as specified and directed.

Supply and fixing for ceiling rose, surface type, 65mm x 50mm, 2 to 3 terminal complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in repairs electric ding dong bell, 230 volt AC, single pole, complete, all as specified and as directed by Engr-in-Charge.

Taking down old unsv MCCB DB TPN type of any size complete all as specified and directed by Engr in charge.

Supply and fixing for flush type bell push, 5 Amp complete all as specified and directed by Engr-in-Charge.

Taking down old unsv MCB DB SPN type of any size complete all as specified and directed by Engr in charge.

Supply & Fixing of LED lights fitting 1x 20W, 220V, Cool White, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, including taking down of old unserviceable light, complete all as specified and directed.

One socket outlet 5 Amp controlled by one switch on independent board complete all as specified and directed by Engineer-in-Charge.

Supply & Fixingof LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, including taking down of old unserviceable light, complete all as specified and directed.

Supply and fixing Vertical type load line distribution board, double door, 12 way, AC, 3 Phase, 415 volts, TPN, bus bar 200 Amps rating and earth bus & din rail suitable for accomodate MCCB 100/125 Amps 16 KA 4 pole as incomer complete all as specified and directed Engr-in-Charge.

Supply and fixing for sheet metal enclosure DB Single pole & neutral 240 volts double door 8 way with 200 Amps rated bus bars and with neutral, earthing bar and din rail complete all as specified and as directed by Engr-in-Charge.

Supply and fix MCCB 125 Amps 4 pole 16 KA 415 Volts, Ics=Icu, 50 Hz with thermal adjustable magnetic settings including spreader link, seperator and any modification required for fixing of MCCB complete all as specified and as directed.

Taking down unserviceable submain wiring of alluminium /copper two runs of any size cable including batten/conduit complete etc and making good distrub surfaces complete all as specified and directed.

Supply & Fixing for MCB, SP 6 to 32 Amps , 240V AC of 10 KA complete all as specified and directed by Engr in charge.

Supply & Fixing for MCB, SPN 40Amps , 240V AC of 10 KA complete all as specified and directed by Engr in charge.

Supply & Fixing for MCB, SP 40Amps , 240V AC of 10 KA complete all as specified and directed by Engr in charge.

Disconnect & taking out carefully pre paid 1ph electric meter and deposit to Air Force Barrack warden and refixing the same inside the meter box including connection with suitable size wire as a functional condition complete all as specified and directed by Engr in charge.

Material & Labour for in replacement submain wiring with two run of 6 sqmm single core PVC insulated but unsheathed FRLS cable of specified size of multistranded copper conductor 1100 volts grade IS:694 marked and one run of 6 sqmm PVC insulated but unsheathed FRLS cable for earth continuty conductordrawn through and under suitable size of rigid non metallic PVC conduit , medium grade, ISI marked ( not less than 20 mm dia) complete with all acessories and fittings all laid/fixed concealed in wall/ceiling or surface in wall and surface conduit on ceiling, and also include the specified runs of specified size earth continuity conductor of similar type cable complete all as specified and directed by Engineer-in-Charge. Note :- Two runs of cable 6 Sqmm (FRLS) and One run of 6 Sqmm copper conductor(FRLS) along with 25 mm dia heavy duty PVC conduit shall be measured as one unit length.

Supply & Fixing in repalcement of LED bldg light highly efficient high power LED bldg light fittings 30 watt with powder coated pressure die cast aluminium high power LED bldg light with heat resistance thoughened glass lens with internally prewired incl electronic driver and connecting up with three core flexible copper condutor 1.5 sqmm cable complete all as specified and directed.

One bell/buzzer point controlled by one push button switch complete all as specified and directed by Engineer-in-Charge.

Material & Labour in replacement of replacement MS flat clamps of size 30mmx5mm thick including nut, bolts and washer suitable for street light bracket fitting on pole complete all as specified and directed.

Disconnect the supply and taking down carefully ceiling fans of 1200mm sweep incl removing the blades from fan and taking custody by contractor and refixing the same in its original position or any other position as per direction of Engineer-in-Charge including its fittings and fixtures after carrying out the the following repair works :- (i) painting of fan motor and blades incl down rod with one coat of synthetic enamel paint (white) by spraying after preparation of surface by cleaning all dust and filling cavity with filler, greasing, bearing ( No 6201/6202/6203/6204), gun metal copper alloy bush suitable for existing make ceiling fans, canopy, U clamps, capacitor of suitable size, heavy duty rubber reel suitable for 1200mm sweep size for ceiling fan and reassembling the fan including testing & MES Number by black permanent merker pen complete all as specified and directed.

Material & Labour for rewinding of burnt fan motor with super enameled copper wire suitable for sweep 1200 mm incl testing complete all as specified and as directed by Engr-in-Charge.

Disconnect the supply and taking down carefully exhaust fans of any sweep and any size and taking custody by contractor and refixing the same in its original position after following necessry repair works :- Dismantling the blades, opening the casting and cleaning the dust properly , greasing and oiling the bearing , cleaning the winding incl applying one coat of synthetic enamel paint by spraying after preparation of surfaces by fillings cavity with filter and cleaning all dust after carrying out proper repairing and testing complete all as specified.

Supply and fixing louvers for exhaust fan of size 300mm sweep including taking out old damaged louvers complete all as specified and as directed by Engineer-in -charge.

Taking down unserviceable SP MCBs of any capacities from the MCCB DBs /MCB DBs after disconnecting the electric supply complete all as specified and directed by Engineer-in-Charge.

Material & Labour for in replacement submain wiring with two run of 2.5 sqmm single core PVC insulated but unsheathed FRLS cable of specified size of multistranded copper conductor 1100 volts grade IS:694 marked and one run of 2.5 sqmm PVC insulated but unsheathed FRLS cable for earth continuty conductordrawn through and under suitable size of rigid non metallic PVC conduit , medium grade, ISI marked ( not less than 20 mm dia) complete with all acessories and fittings all laid/fixed concealed in wall/ceiling or surface in wall and surface conduit on ceiling, and also include the specified runs of specified size earth continuity conductor of similar type cable complete all as specified and directed by Engineer-in-Charge. Note :- Two runs of cable 2.5 Sqmm (FRLS) and One run of 2.5 Sqmm copper conductor(FRLS) along with 25 mm dia heavy duty PVC conduit shall be measured as one unit length.

Excavation in trenches in soft/loose soil not exceeding 1.50 Mtrs wide and not exc. 1.5 Mtr deep and getting out for taking out/laying cable, poles &stay etc complete all as specified and as directed by Engr-in-Charge.

Material & Labour in replacement of replacement GI pipe light grade 40mm dia bracket to make shape L type for street light fitting complete all as specified and directed.

Taking out old unserviceable LT under ground cable any type from trenches, pipes & poles complete all as specified and directed by Engineer-in-Charge.

Returning, filling in including spreading leveling, watering and well ramming in layers not exc 25 cm thick after the cable have been laid tested complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement of sheet metal enclosure single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB 20 amps complete all as specified and directed by Engr-in-Charge.