Indoor Stadium, Football Ground and Gallery at Ghilamara, North Lakhimpur

Amount

Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.4.1) C) UNIFORM PILE (II) Concrete Grade M25 iii) Pile dia 400 mm

Extra for boring specified diameter pile in high sub-soil water level requiring use of drilling mud and extra cement (iii) 400 mm dia

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) (A) TMT bar made of Primary producer (From Primary producer)

Initial test for test loading to 2 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load)

Earth work in Excavation for foundation trenches of walls , Retaining walls, footing of column , steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work , breaking clods in return filling , dressing Watering and ramming etc.and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. Upto a depth of 2 mts. below the existing Ground Level In ordinary Soil

Earth /Sand filling in plinth in layers not more than 150 mm thick including necessary carriage , watering , ramming etc. completed and specified including payment of land compensation , forest royalty , sales tax and other duties and taxes as may be necessary. (a) With earth or silt or sand obtained by head load with lead upto 90m and lift upto 2m.

(c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading.

Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary forest royelty, sales tax, land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantity) etc. complete as directed and specified. (b)Other than Guwahati city only

Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. Brick on flat soling.

Plain cement concrete works with course aggregate of sizes 13mm to 32mm in foundation bed for footing steps, for walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (Shuttering where necessary shall be measured and paid separately) In proportion- 1 cement : 3 sand : 6 coarse aggregates by volume

Plain cement concrete floor base in prop 1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. c) 100mm thick

Providing and laying 25mm thick damp proof course with cement concrete in prop 1:1.5:3 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) (I) Using Mixer Machine In substructure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. P) Using admixture, plasticiser etc for air entraining, water reducing purposes including addition of agent for changing normal setting time of concrete as required. c) M25 grade concrete

In super structure from plinth level up to 1st floor level. Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. P) Using admixture, plasticiser etc c) M25 grade concrete b) M20 grade concrete or Prop. 1:1.5:3 (Playing area floor)

Extra over item Nos. 2.2.1 (I) (B), above for each subsequent floor or part thereof above the 1st floor level.

Providing formwork of ordinary timber planking so as to give a rough finish including centering, shuttering , strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0 m and removal of the same for cast - in - situ reinforced concrete and plain concrete work: In Substructure upto Plinth Level : Foundation, footings, base of columns, pile cap, raft and mass concrete works etc. Using 25mm thick plank

Sides of tie beams, plinth beams, grade beams etc. at or below plinth level Using 25mm thick plank

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in: Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. (a) For depth not exceeding 1.0M.

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. (a) Floors etc. upto 200mm in thickness.

Staircase with sloping or stepped soffits including risers and stringers but excluding Landing.

Extra for each subsequent floor or part thereof above the First Floor level as mentioned in item no. 3.2.1 .

230mm thick brick wall in cement morter with 1st class brick including racking out joints and curing complete as directed in structure (I) In Sub-structure upto plinth level including dewatering if necessary (c). In proportion 1:5.

100mm thick wall using Cellular Light Weight concrete block of Size 500x200x100mm conforming to IS-2185 Pt-3 or pt-4 in cement mortar of proportion 1: 5 including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding rod is to be provided at every 3 course interval and will be measured and paid separately)

Extra for CC block walling on item no 4.3.5 for each subsequent floor or part thereof above the 1st floor level.

200mm thick wall using Cellular Light Weight concrete block of Size 500x200x100mm conforming to IS-2185 Pt-3 or pt-4 in cement morter of proportion 1: 5 including racking out joints and curing complete as directed in structure (protruding rod is to be provided at every 3 course interval and will be measured and paid separately) (b) In Super structure above plinth level upto 1st floor level

10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. b) In cement mortar 1:4

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. B) On fair side b) In cement mortar 1:4

20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. A) On rough side (backing coat 15 mm and finishing coat 5mm thick) b) In cement mortar 1:4

Extra over item no 6.2.1 to 6.2.3 for plastering on celling and soffits of stairs up to 1st floor level (instead of plastering on walls) including curing complete as directed.

Extra over item no 6.2.1to 6.2.3 for interior plastering above 1st floor level for every addl floor or part thereof including curing complete as directed. a) On Single coat plaster

Extra over item no 6.2.1 to 6.2.3 for exterior plastering over wall up to a height of 1st floor level above ground level including curing complete as directed. b) On two coat plaster

Extra over item no 6.2.1 to 6.2.3 for exterior plastering over wall for every addl floor or part thereof beyond 1st floor level including curing complete as directed. b) On two coat plaster

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (ii)Super Ductile (SD) TMT reinforcement bars

Extra over item 18.1.1(a) for each subsequent floor or part thereof 1st floor to 2nd floor level.

Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm) (I) Thickness = 1.5 mm

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Wall painting (two coats) with acrylic emulsion paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth - Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Extra for every subsequent coat of wall painting with acrylic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) - Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Finishing wall with two coats of acrylic emulsion exterior coatings of Unicem "Rakshak" brand of required shade by thinning 1ltr. of paint with 750ml of water to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials as specified and directed by the department.

Extra over item no.13.5.2 above for every subsequent coat of acrylic emulsion exterior coatings of Unicem 'Rakshak' brand of required shade.

Providing and fixing Flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panel conforming to relevent to IS Code including oxidised iron butt hinges (100 mm X 75 mm X 3.5 mm) 6 nos. with necessary wood screws. Non Decorative Type and Block Board core (i) 35 mm thick with panel inserts of 20 mm thick.

Providing, fitting and fixing anodised aluminium windows and ventilators of standard sections of approved brand without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels. (Cement concrete to be measured and paid separately). a)Side hung and Top hung windows and ventilators i) 6 mm clear glass

Providing, fitting and fixing anodised aluminium sliding windows and ventilators of standard sections of approved brand without horizontal glazing bars, joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as required complete as specified and directed for all levels. (a)2 Track sliding window (i)6mm clear glass

(b)3 Track sliding window i) 6 mm clear glass

a) Providing, fitting and fixing anodised aluminium fixed windows and ventilators of standard sections of approved brand, joints mitred welded (manufactured to relevant I.S. specification) fitted with glass panes of required thickness and 12mm prelaminated boards and providing and fixing handles, angle cleat, rubber gusket,roller bolting device, screws as required complete as specified and directed for all levels. (a) In Normal anodised Aluminium section (i) With 6mm thick glass panes

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) a) Normal range Somany/ Orient/Nitco /Varmora/VITA/ Marbito/ Make ii) Of size 600mmx600mm and above

Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed. VITRIFIED TILES iii)Executive range-2 (Sizes 600 mm x600mm and above) i) Nitco made/Quotone/Somany a)Imperia Series- Gres Tiles

25 mm thick cement concrete topping 1:2:4 (1cement : 2 coarse sand : 4 coarse aggregate of 12 mm nominal size) finished with a floating coat of neat cement finish to be laid in panels including curing complete as directed.

Providing Ceramic Tiles of approved quality, size, shape and thickness not less than 8 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with fix-A Tile Choksey/ Sika/ Pedelite/ Rouf/ White cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed (coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). Normal range Of size 400x400 mm and above

Providing 18mm thick Granite slab on vertical face of pedestal laid over 10 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as directed with approved quality of shade.

Providing polished granite slab of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile Choksey/Sika/Pedelite/Rouf) /white cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). (i) Executive Quality (i) With Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)

Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) m) Mortice lock vertical type iii) 100mm(Godrej with handle (6 lever)

iv) Aldrop with In built Lock-6 lever kadi tala(Godrej Make)

t) Door stopper with rubber stopper

Supplying, fitting, fixing Stainless Steel fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary c.p. brass screws etc. complete.( bright natural matt & satin finished ) b) Tower Bolt i) 300mm x 10mm

c) Door Handle iii) 150mm

Providing,fitting and fixing Door closer of various type UL listed and fire rated good quality depending on the door specification.Types like single speed,Double Speed,Heavy Duty etc are available and as directed & specified by the department. A) Godrej c) Heavy Duty Door Closer( size 180 mm x 65mm x 64mm)

Supplying, fitting and fixing goat proof wire fencing 1200mm high with horizontal wire spacing at 100mm, 100mm, 100mm, 100mm, 100mm, 100mm,150mm, 150mm, 150mm and 150mm from bottom onwards and vertical wires at 130mm apart, first 3 horizontal wires from top barbed wire apart, first 3 horizontal wires from top barbed wire 12 S.W G.x 2 plies x 4 points x 100 mm apart bottom wire 10 S.W.G. fitted with angle iron posts specified in item no.17.7 above including supplying, fitting and fixing with necessary hooks, bolts and staples etc. and painting one coat to all iron posts etc. with anti-corrosive black paint etc. complete as directed and specified(intermediate and straining post should be placed not more than 4000 mm and not less than 3000 mm apart and all posts embedded in C.C. pillars of size 300mm x 300mm x 600mm in prop 1:3:6).

Preparing the RCC surface in roof slab, chajjas, terraces, sunken slabs, septic tank, OH tank, raft slab, walls etc. by thoroughly cleaning with wire brush etc. followed by power washing for making the surface absolutely free from any foreign particles like dust, oil, grease etc. and allowing surface to dry complete as directed at all levels.

Supplying, mixing, laying and applying the following waterproofing systems over Raft slabs, Roof slabs, Terraces etc. including curing complete as specified and directed by the Department at all levels.: (i) 1mm thick single coat of Master Crete M-81 of Choksey Chemicals /Dr. Sealkit Sealcrete (Asian Chemicals)/RHEOMIX 131of BASF mixed with cement in the ratio 1:2 as a prime coat. (ii) 3mm thick Polymer modified mortar - Cement sand mortar (in prop 1:3) mixed with Master Crete M-81/Dr. Sealkit Sealcrete (Asian Chemicals)/RHEOMIX 131of BASF @ 15% by weight of cement. (iii) 1mm thick coat of Master Crete M-81 /Dr. Sealkit Sealcrete (Asian Chemicals)/RHEOMIX 131of BASF mixed with cement in the ratio 1:2 as final coat. (A) Using Master Crete M-81 of Choksey Chemicals /Dr. Sealkit Sealcrete (Asian Chemicals)

Pre construction anti - termite treatment in the back fill in immediate contact with the foundation structure after completion, column, wall etc. to a depth of 450mm and width 300mm (when required refill in 200mm thick layers) applying the emulsion @ 5 (five) litres per square meter towards the concrete and masonry walls so as to ensure earth in contact with the structure well treated - with chemical (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

Pre construction anti - termite treatment by applying in the entire levelled area after plinth filling and before laying floor by applying the emulsion @ 5 (five) litres per square meter of the surface to be spread with light rodding so as to ensure proper absorption by the filled up earth (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. b) with aqueous emulsion having concentration 1:499 with Premise 350 SC (Imidachloprid 30.5% SC) and water, i.e. 0.07% solution.

Pre construction anti - termite treatment by applying in the junction of walls, column with the floor before laying floor and after operation of item no. 26.1.3 above making a channel 30mmx30mm all over the walls and making rod holes @ 150mm apart up to ground level below and applying emulsion @ 11 litres per square meter of vertical plinth wall surface inside the building so as to soak the soil with the emulsion up to the ground level and refill the holes and channel with the original materials obtained in making channels (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

Construction of Granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per Clause 401 of MoRTH specifications (with an initial lead of 5 km) (including cost of testing of materials at site and laboratory as directed by the deptt.) (b)Using Grading II material

Providing, laying, spreading and compacting stione aggregates of specific size to water bound mecadam specification including spreading in uniform thickness, hand-packing, rolling with vibratoy roller8-10 tonnes in stages to proper grade and camber, applying and brooming Type -A (13.2 mm agg.) screening/binding material to filled up the interstices of coarse aggregate watering and compacting to the reqd. density( with all initial lead of 5.0 Km) By Manual means Grading II using Screening Type B(11.2mm agg)

Providing and laying of inter locking concrete block pavement (ICBP) with cement concrete paver blocks as per IS 15658-2006 of thickness 80mm and 28 days compressive strength not less than 40 N/m over a layer of bedding sand of compacted thickness 30mm, laid either in stretcher/ running/ herringbone pattern of bonds as directed by the engineer and in proper level and grade and compacted with appropriate equipment such as plat vibrator along with spreading of a thin layer of joint filling sand to fill up the gaps between blocks including construction of edge restraint wherever required complete as per drawings and Technical specification clause 1504 of MORD.

Providing plinth protection 50mm thick to cement concrete 1 : 3 : 6 with coarse agg.of 20mm nominal size including finishing the surface with 10mm thick cement plaster in proportion 1:3 with a floting coat of neat cement finished.

Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) M/F Suspended Ceiling which includes G.I. perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending G.I. intermediate channels of size 45mm (0.9mm thick with two equal flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angle of width 25mmx10mmx0.55mm thick fixed to soffit with G.I.cleat and steel expansion fasteners. Ceiling sections of 0.55 mm thk with knurled web of 51.5 mm and two equal flanges of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips perpendicular to the intermediate channel at 457mm c/c and 12.5 mm thk gypboard fixed to the ceiling sections with 25 mm drywall screws at 230mm c/c. the boards joints are finished with joint paper and two coats of drywall topcoat at all levels including cutting for providing and fixing light fixures whwre ever necessary. and as p[er design.

Providing and fixing Stainless steel (Grade 304) railing made of Hollow tubes, channels, plates, etc. including welding , grinding buffing, polishing and making curvature, (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete , i.e. fixing the railing with necessary accesories & stainless steelm dash fasteners , stainless steel bolts etc. of required size, on top of the floor or the side of waist slab with suitable arrangement as per the approval of Engineer in-charge .(For payment, only weight of stainless steel member is to be considered . No extra payment for fixing accessories such as nuts, bolts, fasteners etc. will be considered. (a) SS Railing Steel with Wire Locator.

Providing, fitting, hoisting and fixing of roof trusses fabricated out of combination of any two or all of the following sections (i) Square section (ii) Rectangular Hollow section of specification RSH/SHS and (iii) M.S. circular hlollow section of Grade 210 including purlins, bottom runners and providing M.S. cleat, M.S. angle base plank, bolts and nuts with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist as per design complete as directed as per specifications. a) Using TATA make RHS/SHS of Grade 310 conforming to relevant I.S. code 4923 : 1997

Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) at all levels including fitting and fixing with self drilling, self tapping screws complete. (Roof trusses, purlins etc. to be measured and paid separately.) TATA Blue scope/ Dyna roof / Spectrum or equivalent as directed by the Departement (iii) 0.50 mm thick

Providing Pre Painted Galvanized Iron Sheet (PPGI) accessories (Ridges / Valley / Gutter /Flashing) at all levels including fitting and fixing self drilling, self tapping screws complete complete. TATA Blue scope/ Dyna roof / Spectrum or equivalent as directed by the Departement (v) 0.60 mm thick

Providing drain with cement concrete (1:3:6) 10cm thick sides 10cm thick bed over brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. ii)300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm.

Providing drain with reinforced cement concrete (1:3:6) 15 cm thick sides 15 cm thick bed over brick flat soling finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. i) 450 mm wide and average 450 mm deep with bed slope 1 in 300 with initial depth of 300 mm.

Providing and installation of Armstrong make simpurity 2 mm thick homogeneous, jointless, cleansweep superior coating T-group wear resistance, Flamability EN 13501 - 1, slip resistance group R9, scratch resistance, chemical resistance, anti fungal and anti bacterial PVC vinyl flooring, installation complete at all levels as per approved shade and colour and as directed by the department.

Supply fitting and installation of "PORPLASTIC" make Indoor PU 7 layer flooring with 7-13 mm thickness consisting of system layers from the top as line paint (0.1mm – 0.2mm), flexible top finish (0.05 – 0.1mm), self levelling layer (2 – 3 mm), scratch layer (ca. 0.5mm), pore sealer (0.1 – 0.2mm), prefabricated mat with adhesive (4 – 10mm) and primer (ca. 0.2mm) on the concrete surface, point elastic according to DIN V 18032-2 and EN 14904, IHF approved, formaldehyde free, pentachlorophenol free with permanent elasticity, good scratch and abrasion resistant quality with 9-19 Nm of impact resistance, 96% of vertical ball behaviour, sliding coefficient of 0.42-0.47, reflectance of 0.48, with 30 mg resistance to wear , thickness coefficient of 5.7-8.2, with maximum vertical deformation of 1.1 mm and shock absorption up to 30%. The colour shall be as approved by the consultant and the department, to lay and install in complete as directed by the department in all levels.

Providing, fitting and fixing of 19 mm thick non-fibrous, fire retardant, closed cell, tri-dimensional chemically crosslinked polyethylene foam. Conforms to 'Class O' for Fire Propagation and 'Class 1' for Surface Spread of Flame of Supreme make Insushield under deck roof insulation with Single layer system with one side aluminium foil installation complete with all accessories at all levels.

Supply and installation of Merino /Greenlam (Nylon) series cubicles of width and depth as per specifications/ site drawings. Cubicle height will be 2003 mm. Made from solid grade compact high pressure laminate as per IS:2046 and EN-438 manufactured under high specific pressure > 5 MPa and temperature >120°C with bunch of kraft papers impregnated with thermosetting phenolic resin and decorative papers made of Alpha cellulose fiber impregnated with thermosetting melamine resin which provide superior scratch, abrasion, heat, chemical, impact, graffiti & moisture resistance along with anti-bacterial properties. Panels have a black core that when machined, presents a distinctive black edge. All doors will be of single colour and made of 12 mm thick HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3 no.s Nylon PA-6 made hinges affixed to the pilasters. Nylon PA-6 made coat hook and lock set are provided with each door. All pilasters will be made of 12 mm thick HPL compact panel with chamfered edge and completed with stainless steel made thumb turn lock set. Aluminum made door stopper profiles with rubber linings for dampening the noise while door closing will be provided at the vertical ends of the pilasters. Pilasters will be anchored to the floor using Nylon PA-6 made adjustable legs .The bottom gap is 100-150 mm. All intermediate partitions or dividers will be made of 12 mm thick HPL compact laminate panels. They are affixed with aluminium made U-channel at their ends for ultimate stability of the system. Design no. as specified by Arch. / Engr. in suede finish. Size of panels to be as per drawing.

Providing fiting and fixing of Wood Plastic Composite (WPC) door frames of natural and brown colour of 100mm x 65 mm section and density not less than 900 kg/ cum, single rebated rectangular section including joining of top mullion and vertical members with mitred joint and fixing to the wall jamb with MS holdfasts/ Metal Screw and metal rawl plug.

Providing fitting and fixing Vitreous china wall hang water closet (European type W.C pan 400mm high) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) ii) Hindware make a) White (i) Constellation (inclusive of seat cover and fittings) (P Trap)

Providing fitting and fixing Vitreous china Dual Flush / Floor Mounted Coupled / Extended water closet (European type W.C pan 400mm high) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) B) Hindware make a) White (i) Constellation (inclusive of seat cover and fittings) (P Trap)

Providing fitting and fixing vitreous china flat back type lipped front urinal basin with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. B) Hindware make a) White (ii) Dyna (Cat. No.60010)

Supplying fiting and fixing vitreous china division plate including fitting and fixing compete as directed and specified. (ii) Hindware Make (a) White (i) Division Plate 680 x 300 (Cat. No.61001)

Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) PEDESTAL BASIN (with pedestal) (B) Hindware Make (a) White (iii) Constellation " 5 (Cat. No.10032/11010)

Under Counter Basin (B) Hindware Make (a) White (i) Lara (Cat. No.10095)

Providing fitting and fixing of chrome plated Jaquar make soap dish (cat no ACN 1131 N)

Providing fitting and fixing of chrome plated 600 mm long Jaquar make Towel rail complete as directed.

Providing fitting and fixing of Jaquar make chrome plated Towel ring complete as directed.

Providing, fitting and fixing Chrome Plated robe hook complete as directed and specified. (a) Jaquar make (i) Continental (Cat.No. ACN-1191N)

Providing fitting and fixing Decorative Mirror complete as directed and specified.Parryware Make Size 800mm x 600mm

Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified. (a) Jaquar Make (i) 32mm (HT/FT) (Cat.No.ALD-705 / 709)

Providing fitting and fixing PVC cowel of ISI make complete as directed and specified. (i) 160mm dia. PVC cowel of ISI make

(ii) 110mm dia. PVC cowel of ISI make

C.P. Grating (ii) 110mm dia

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) (ii)Jaquare make (a)Continental /Clarion (i)Standard

(iii)2-Way bib cock

Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid separately) (i)Jaquar (a) Continental / Clarion (ii)15mm dia( Angular stop cock )

(iv) 15mm dia, (Concealed stop cock extra heavy with adjustable wall flange )

Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed. (ii)Jaguar make (a) Continental

Supplying fitting and fixing Chrome Plated (C.P.) sink cock of approved brand as directed and specified. (G.I. & C.P pipes will be measured and paid separately) Jaquar brand a) Continental / Clarion i) Sink cock with swinging casted spout

Supplying fitting and fixing Chrome Plated (C.P.) shower 15mm dia. Of approved brand as directed and specified. (Pipes will be measured and paid separately) (iii)Jaquar make a) Continental (ii) Shower arm 190mm long heavy casted body with wall flange

Supplying fitting and fixing Telephonic Chrome Plated (C.P.) shower of approved brand as directed and specified. (Pipes will be measured and paid separately) Essco make (a) Telephone shower delux with 1m PVC tube and wall hook

Supplying, fitting and fixing Chrome Plated (C.P.) wall mixer complete as directed. Jaquar make a) Continental/ Clarion ii) Wall mixer non telephonic shower arrangement Cat No.219

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia.

(ii) 110mm dia.

(iv) 75mm dia.

(v) 63 mm dia.

(vi) 50mm dia

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm

(ii) 110mm dia.

(iv) 75 mm dia.

(v) 50mm dia

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia

(ii) 110mm dia.

Supplying fiting and fixing 45degree PVC bend of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia

(ii) 110mm dia.

(iv) 75 mm dia.

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia

(ii) 110mm dia.

(iv) 75 mm dia.

Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia

(ii) 110mm dia.

(iv) 75 mm dia.

Supplying fiting and fixing PVC single ‘Y’ of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia

(ii) 110mm dia.

(iv) 75 mm dia.

Supplying fiting and fixing PVC single ‘Y’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110mm dia.

(ii) 75 mm dia.

Supplying fiting and fixing PVC coupler of (Supreme / Prince)or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110 mm dia

(iii) 75 mm dia

Supplying fiting and fixing PVC reducer of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (i) 160mm x 110 mm

(iv) 110 mm x 75mm

Supplying fiting and fixing PVC reducing Tee of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (i) 160mm x 110 mm

(iii) 110 mm x 75mm

Supplying fiting and fixing PVC cleaning pipe of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified. (a) 160 mm

Providing fitting and fixing of Chlorinated Polyvinyl Chloride (CPVC) Pipes having thermal stability for hot and cold water supply with all necessary plain and brass threaded fittings and fixing the pipes with clamps at 1.0 m interval including jointing of pipe. a) 15 mm nominal outer dia pipe

b) 20 mm nominal outer dia pipe

c) 25 mm nominal outer dia pipe

d) 32 mm nominal outer dia pipe

e) 40 mm nominal outer dia pipe

f) 50 mm nominal outer dia pipe

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed B) uPVC pipe with uPVC fittings ( Using uPVC high pressure pipe) (Using SUPREME/ PRINCE/ SFMC/ FUSION brand pipe) iii) 25mm diameter

iv) 32 mm diameter

v) 40 mm diameter

vi) 50mm diameter

Supplying and placing ferrocement water tanks of circular/rectengular shape over stagging with manhole cover with locking and clearing arrangement including providing pads of size as required for inlet and outlet pipes complete as directed.(Stagging should be measured and paid separately). 2000 Lt capacity water tank

1000 Lt capacity water tank

Supplying and placing ferrocement septic tanks of rectangular shape in to pit with manhole cover with cleaning arrangement over single brick flat soling and 75mm 1:3:6 P.C.C. Baffle wall, inlet and outlet etc are provided at suitable points complete as directed. 100 Users

200 Users

Supply, Installation, Fixing of DRY CHEMICAL POWDER Fire Extinguisher confirming to IS: 2171 with ISI mark and CO2 cartridge will be confirming to IS: 4947 with ISI mark, Powder will be confirming to IS: 4308 with ISI Mark (10 kg) BRAND : FIRESTOP / FIREND / FIRE SHIELD

Supply, Installation, Fixing of MECHANICAL FOAM (AFFF) Fire Extinguisher confirming to IS: 10204 with ISI Mark and CO2 Cartridge will be confirming to IS: 4947 with ISI mark, (AFFF) will be confirming to IS: 4989 with ISI Mark.(9 LTRS) BRAND : FIRESTOP / FIREND / FIRE SHIELD

Supply, Installation, Fixing of ABC Stored Pressure Fire Extinguisher with built – In pressure Gauge to know the Ready ness of the Extinguisher Squeeze Grip Handle As per IS:13849 with ISI mark (05 kg capacity) BRAND : FIRESTOP / FIREND / FIRE SHIELD

Supplying including fitting fixing of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator]. Premium model 1200 mm Sweep (ORIENT PSPO make) / Premium model 1050 / 1200 mm Sweep SS-390 Deco Havells make)

Supplying including fitting and fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt. as required complete and as directed by the Department. Domestic Power Flow 225 mm sweep (ORIENT make)

Heavy Duty 450 mm sweep 900 RPM Single phase (Crompton make), Heavy Duty 450 mm sweep 900 RPM Single phase (Usha make)

Supplying including fitting fixing of following A.C. Wall fan in the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. (CROMPTON /ORIENT/Havells/USHA or equivalent make) SDX 120 with metal body metal blade 400 mm sweep

Wiring to 5 pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed 2 mm thick/ heavy rigid ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system including 5 pin 6 Amps flush type plug socket and 6 Amps F/T switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. mark with phenolic laminated sheet cover including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete, when placed elsewhere. Short point upto 3.0 m length

Medium point upto 6.0 m length

Long point upto 10.0 m length

Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including and fixing 5/6 pin 16 Amps flush type socket outlets and 16 Amps flush type switch ( Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. mark with phenolic laminated sheet cover earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) Short point upto 3.0 m length

Medium point upto 6.0 m length

Long point upto 10.0 m length

Extra Long point upto 15.0 m length

Extra long point upto 20.0 m length

Wiring for light/fan/bell point with 2 x 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring with 20 mm dia 2mm thick/ heavy rigid ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system including 6 Amps flush type switch/bell push (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. mark with phenolic laminated sheet cover as required complete, when placed elsewhere. Short point upto 3.0 m length

Medium point upto 6.0 m length

Long point upto 10.0 m length

supplying with fitting and fixing of modular starter of following specification complete with making necessary connection as specified and directed.overload relay range 9-15 Amps in 3 module

Supply with fitting and fixing of 100 W 4 step modular(2 module) fan speed controller of legrad, MK, ABB, colors, Schneider etc with necessary connection as directed by the department.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system. With 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

With 3 x 4 sq mm + 2 x 2.5 sq mm earth connectivity in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

With 4 x 6 sq mm + 2 x 4 sq mm earth connectivity in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

With 4 x 10 sq mm + 2 x 6 sq mm earth connectivity in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Supplying with fitting and fixing sheet steel, phosphatised, powder dust & vermin proof Double door (IP-43) surface mounting SPN MCB DB incorporated with bas-bar, Neutral link, Eart bar & din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection approved, specified and directed by the deptt. 4 way SPN double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof reversible Double door (IP-43) surface mounting horizontal TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. (Schneider neo break, C&S, Havells, INDOASIAN, Standard, HPL or equivalent Make as approved by the Deptt.) 4 way TPN (8+12) double door

6 way TPN (8+18) double door

8 way TPN (8+24) double door

12 way TPN (8+36) double door

Supplying with fitting and fixing MCCB incomer and MCB outgoing sheet steel, phosphatised, powder painted single door surface mounting vertical TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar up to 125A and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 8 way TPN (4+24) single door

Supplying fitting and fixing of SPN 10 KA 240/415 V 50 Hz MCB of the following capacity complete with making necessary connection as approved specified by the department. B series Schneide, Legrand, Crabtree etc 6 AMP to 32 AMP

Supplying with fitting and fixing DP 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. B Series (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 6 to 32A

Supplying fitting and fixing of TP 10 KA 240/415 V 50 Hz MCB of the following capacity complete with making necessary connection as approved specified by the department. B series Schneide, Legrand, Crabtree etc 40 AMP

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 100/300mA sensitivity DP RCCB (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 25A

Supplying including and fixing of metal boxes in recessed system complete as per direction of department. Legrand/anchor/schneider or equivalent 1-2 module type metal

3 module flush type metal

4 module flush type metal

6 module flush type metal

8 module flush type metal

10 module flush type metal

12 module flush type metal

16 module flush type metal

Supplying including fitting fixing of logic front plate of suitable colour as per direction of department. Legrand/anchor/schneider or equivalent 1 module type metal

2 module type metal

3 module flush type metal

4 module flush type metal

6 module flush type metal

8 module flush type metal

10 module flush type metal

12 module flush type metal

16 module flush type metal

Supplying with fitting fixing 6 amp one way modular clip in switch in recessed system including making necessary connection complete as per direction of department. Legrand/anchor/schneider or equivalent

Supplying with fitting fixing 16 amp one way modular clip in switch in recessed system with LED indicator including making necessary connection complete as per direction of department. Legrand/anchor/schneider or equivalent

Supplying including installation of socket outlet 6/16 Amps 3/5 pin combine shuttered complete as per direction of department. Legrand/anchor/schneider or equivalent

Supplying including installation of socket outlet 6/16/13 Amps cInternational; socket with making necessary connection as per direction of department. Legrand/anchor/schneider or equivalent

Supplying including installation of socket outlet 6 Amps 3 pin combine shuttered complete as per direction of department. Legrand/anchor/schneider or equivalent

Supplying with fitting fixing 10/16 amp one way modular clip in switch in LED in recessed system including making necessary connection complete as per direction of department. Legrand/anchor/schneider or equivalent

Supplying including fitting and fixing of rigid PVC. Conduit pipes including painting etc. complete in surface wiring system. 25 mm. Dia, 1.5 - 2.0 mm mm thick, rigid PVC. Conduit pipes

Supplying with fitting fixing blank plate single in modular switch recessed system with including making necessary connection complete as per direction of department. Legrand/anchor/schneider or equivalent

2HP single phase monoblock pumpset (Crompton Greaves/V guard make)2900 RPM with DOL starter (Crompton Greaves/L&T/ Siemens make)

Supplying and fixing of Jaquar make 40W LED TUBE LIGHT CAT no LUNIOX220 XC fittings complete with Shade, back plate including connection cable, as approved by the Deptt.s etc. as required.

Supplying and fixing of 22 W LED Strip BattenJaquar(CAT NO LGLZPCX022XC) or equivalent LED strip batten light fittings complete with Shade, back plate including connection cable, as approved by the Deptt.s etc. as required.

Supplying and fixing of Jaquar or equivalent recessed mounted LED downlighter with aluminium die cast housing fittings complete with Shade, back plate including connection cable, as approved by the Deptt.s etc. as required. LED 9W (CAT NO NERO Square LNRO01S009XC) 6500K

LED 12W (CAT NO NERO Square LNRO01S012XC) 6500K

LED 18W (CAT NO NERO Square LNRO01S018XC) 6500K

Supplying and fixing of Jaquar or equivalent recessed mounted 36W 2' x 2' 125Lm/W LED panel 6500K downlighter withwhite powder coated CRCA housing with full mounted acrylic diffuser fittings complete with Shade, back plate including connection cable, as approved by the Deptt.s etc. as required.

Supplying and fixing of Jaquar(Breva) or equivalent surface mounted 1 x 8W 3000K IP54 up lighter with aluminium housing and transparent tempered glass diffuser fittings complete with Shade, back plate including connection cable, as approved by the Deptt.s etc. as required.

Supplying and fixing of Jaquar or equivalent surface mounted 2 x 3W 3000K IP54 up-down lighter with aluminium housing and transparent tempered glass diffuser fittings complete with Shade, back plate including connection cable, as approved by the Deptt.s etc. as required.

Sri Prasanta Gogoi