SPECIAL REPAIR TO CERTAIN BUILDINGS AND PROVN OF 4X URINAL POINTS AND 2X TOILETS AND CONVERSION OF LT OVER HEAD TO LT UG CABLE AT CERTAIN LOCATION AT BENGDUBI MIL STN UNDER GE BENGDUB

Amount

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc, disposing off the retrieved debris outsite the premises, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc, disposing off the debris outsite the premises, complete all as specified and as directed.

S&F factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary provision of lugs, locks strike plate, hinges etc, applying one shop coat of Zinc Chromate primer after prepation of the surfaces, complete all as specified and as directed.

S&F factory made 1.25 mm thick pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary provision of lugs, locks strike plate, hinges etc, applying one shop coat of Zinc Chromate primer after prepation of the surfaces, complete all as specified and as directed.

S&F Factory made 30mm thick flush shutter solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and as directed.

M&L for 2nd class hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 30 mm thick glazed and skeleton shutters, open rebated and prepared to rceieve glass, gauze, etc, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a), complete all as specified and as directed.

S & F factory made steel windows with side hung shutters including box type hinges with steel handle, and peg stay, complete with glazing bars, dovetaild or welded, also including application of one shop coat of Zinc Chromate primer, complete all as specified and directed.

All as per Item No 7 above, above but steel windows without glazing bars.

S&F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and as directed.

S&F 100mm size butt hinges, heavy weight, cold rolled, mild steel, complete all as specified and as directed

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt, 150 mm long of extruded section, complete all as specified and as directed.

S&F 150 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

M&L for preparing new wooden surfaces of any description not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed .

Hacking out old broken glass any thickness, size, quality and description from metal frames including punching or drilling out old glazing pins /springs clips, complete all as specified and directed.

S&F 4mm thick figured glass, pin head type and glazing for steel surrounds with & including oil putty, in squares n exc 0.50 sqm in each pane, complete all as specified and as directed.

S&F 4mm thick sheet glass of ordinary quality and glazing for steel surrounds with & including oil putty, in squares n exc 0.50 sqm in each pane, complete all as specified and as directed.

Taking down cement plaster on brick or concrete surfaces etc, including raking out joints, hacking for key, scrubbing down with water etc, and also including removal of rubbish off the premises, complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:4) on fair faces brick work or concrete surfaces finsihed even and smooth (without using extra cement) mixed with water proofing compound in top layer of 5mm thick as per manufacturer instructions, complete all as specified and as directed. Note:- WPC shall be measured and paid seperately

Supply only liquid water proofing compound, complete all as specified and directed..

M&L for rendering 15 mm thick in cement mortar (1:6), on brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:3 on concrete surfaces of ceiling/Chajja/Facia of chajja etc, finished even and smooth without using extra cement, complete all as specified and as directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of cement based paint over a coat of primer, complete all as specified and directed.

M&L for preparing new plastered surfaces of walls, applying two coats of wall care Putty (minimum thickness of two layers shall be 1.5mm) and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coat of white washing, complete all as specified and directed .

M&L for preparing new plastered surfaces of walls, applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed.

M&L for washing, rubbing down and stopping of painted surfaces thereafter preparation of plaster or unplaster surfaces wall and applying one coat of white wash, complete all as specified and directed.

M&L for complete removal of existing treatment from the external surfaces of wall etc, thereafter prepartion the surfaces and applying two coats of cement base paint , complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles of size 300mmx 450mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM 1:4, complete all as specified and and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/ blankets, any thickness, including cover fillets, and existing frame work also, complete all as specified and as directed.

S & F 4mm thick Non-asbestos fibre cement decorative/designer building boards to aluminium frame work with screws in ceiling (flat and/or slopping) and including jointless finish with & also including joining compound and tape as per manufacturer instructions, complete all as specified and as directed. Notes :- (i) The board shall be confirming to IS-14862 and shall be manufactured from the homogeneious mixture of cement, quartz and cellulose and shall be curred with high pressure steam using auto claving process. (ii) Aluminium frame work shall be measured and paid for separately.

S&F anodised aluminium snap grid frame work for false ceiling hangers 6mm dia GI (upto 1200mm length) adusting level fixed to roof slabs by means of ceiling cleats made out GI flat iron 40x3mm size 60mm long and fixed expansion hold fasteneners 12.5mm dia and 40mm long, complete all as specified and as directed.

M&L for preparation of new surfaces of Non-asbestos fibre cement boards as in ceiling and applying two coat of oil bound distemper over a coat of primer , complete all as specified and as directed.

Taking down 15mm bore steel tubing & connections, complete all as specified and as directed.

All as per item No 36 above but 20 mm bore

S&F 15mm bore medium grade, galvanised steel tubing (including in short lengths) with and including all fittings, fixed in the walls & ceiling or laid in floors, complete all as specified and as directed.

S&F 20mm bore medium grade, galvanised steel tubing (including in short lengths) with and including all fittings, fixed in the walls & ceiling or laid in floors, complete all as specified and as directed.

S&F 20mm bore medium grade, galvanised steel tubing (including in short lengths) with and including all fittings, laid in trenches, complete all as specified and as directed.

Cutting existing steel tubing of size 40/50mm bore for alterations or additions and Screwing existing steel tubing for alterations or additions, complete all as specified and as directed.

Taking down PVC SWR Pipes ( any size or pattern) including all fittings, heads, shoes etc, complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints laid in floors/ trenches etc, complete all as specified and directed.

S & F 110 mm bore PVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, laid in floors/ trenches etc, complete all as specified and directed.

S & F 110 mm bore PVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc, complete all as specified and directed.

S&F PVC (SWR) vent cowl, 110 mm bore, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends (any radius), complete all as specified and directed.

S&F 110mm bore uPVC (SWR) bends (any radius), complete all as specified and directed.

S&F 110mm bore PVC (SWR), junction single (single T), equal or unequal with and including rubber ring joints, complete all as specified and directed.

S&F in repair rotational moulded polyethylene water storage tank 500ltrs capacity, ISI marked, (cylindrical vertical type double-layered) with closed top including inlet,outlet and wash out holes, provision of G.I Fittings for fixing of the inlet, outlet and washout pipes, hoisted in position, complete all as specified and as directed.

S&F in repair gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 20 mm bore, complete all as specified and directed.

S&F gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 20 mm bore, complete all as specified and directed.

S&F in repair Ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, screwed for iron pipe of 20mm bore (Minimum weight 455 grms), complete all as specified and as directed.

S&F in repairs bib tap, fancy type, long swan neck, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and as directed.

S & F in repair cast copper alloy, chromium plated, wall mixer, Non-telephonic shower system with Aerator for mixing hot & cold water, screwed down for 15mm bore iron pipe, complete all as specified and as directed

S&F in repair angle stop cock, fancy type, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed.

S&F in repairs Vitreous China Wash Down Water closet (Pedestal Pattern) 1st quality, , white (excluding flushing cistern & flush pipe) including plastic water closet seat white, closed pattern with flat bottom and cover and mild steel CP or aluminised huiging device, making connections, complete all as specified and as directed.

S&F in repairs PVC valveless, double syphonic action type, flushing cistern, low level of 10 Litres capacity, white, with and including inlet, ball valve, float, 32mm dia flush pipe of polyethylane of low or high density or PVC, flushing bend & handles, also including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet & making connections, complete all as specified and as directed.

S&F in repair vitreous china wash basin, 1st quality, white, flat back, approx size 510x410mm excluding taps but including 32 mm bore brass chromium plated waste fittings, 32mm bore PVC waste pipe, MS brackets, complete all as specified and as directed.

S&F in repair PVC connection 15 mm size with PTMT nuts of length 600 mm, complete all as specified and directed.

S&F in repairs brass chromium plated shower roses, 125 mm size with or without swivel joints (including Shower Arms) to 15mm bore steel pipe or union, complete all as specified and as directed.

S & F in repairs soap dish CP, fixed to wall with and including plugs & chromium plated screws, complete all as specified and as directed.

S&F in repairs tubular towel rail, 20mm dia, D type, brass chrormium plated, 600mm long between flanges, complete all as specified and as directed.

M&L for Preparation of steel and iron surfaces of any description duly applied with shop coat of primer, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint, complete all as specified and as directed. Note : Cost of application of shop coat of primer not included in this item.

Demolition of brick work or rubbled stone masonry including all quoins, arches , pillars etc built in cement mortar including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for Brickwork with fly ash Bricks, old size of class designation 75 (i.e of average compressive strength 75 Kgf/Cm2) straight or curved on plan exc 6m mean radius, built in Cement morter 1:6, complete all as specified and directed

M&L for Brickwork with fly ash Bricks, old size of class designation 75 (i.e of average compressive strength 75 Kgf/Cm2), straight or curved on plan to any radius in half brick thick wall, built in Cement Morter 1:4, complete all as specified and directed.

S&F in reapair stainless steel decorative curtain rod of 25 mm bore with wood finishes, complete all as specified and as directed.

S&F brackets and fancy type funnel caps suitable for the curtain rod to be provided under item No 62 above, complete all as specified and as directed.

S&F jet spray (including 1m PVC tube) to 15mm bore steel pipe or union, complete all as specified and as directed.

S&F in repair angle cock, two way cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed.

M&L for Preparation of back surfaces of pressed steel chowkhat any description and girth, not otherwise described, and treated with tar or coal tar black paint, complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregates) as in hold-fast blocks, blocks for fixing lugs, filling of pressed steel chowkhat and the like including necessary form work, complete all as specified and as directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed.

S&F in repairs, vitreous china urinal, 1st quality, Half Stall Type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified and directed.

S&F standard aluminium anodised aluminium section as in frame, shutters for doors, windows / ventilators, Fixed/ Openable / side hung/ sliding two or three track or in any pattern, partitions, kitchen cabinet/almirah etc, cut to size, jointed with cadmium plated steel screws, including Aluminium beading & rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc, complete all as specified and directed. Notes:- (i) Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. (ii) The accessories (including Aluminium mongries etc) required to be provided for windows, vents and doors as per directions of Engineer-in-charge shall be provided but weight for the same shall not be considered for payment. (iii) Cost of all the items, accessories & Aluminium mongries required for the entire completion of the work shall be deemed to be included in the quoted rate. However glass panes, wire cloth shall be measured and paid separately under respective items.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and as directed.

S&F in repairs Mortice lock, 4 levers vertical type, size 100 mm, complete all as specified and directed.

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, complete all as specified and directed.

S&F 5.5mm thick sheet glass of ordinary quality frosted one side and and glazing for Aluminium Joinery, in squares exc 0.50 sqm in each pane, complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified and shown on drawing for SI No. 08095 on Srl Page No. 180 of SSR (Part-II) and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,, complete all as specified and shown on drawing for SI No. 08080on Srl Page No. 176 of SSR (Part-II) and as directed.

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, complete all as specified and as directed.

Dismantling wrought iron as in rafters, purlins, truss etc and/or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering/ cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

S&F pre-painted colored plain sheet profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer,as in roof covering/ cladding to wall fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

M&L for making good with cement mortar 1:6, under cills or over arches, lintels and bressummers, including all pinning when necessary, complete all as specified and directed.

S&F roof trusses (framed), trussed, purlins, crane gantry, rails and fastenings and heavy brackets framing (Beam, Tee, Angle,, Channel or Flat Sections) including distance pieces, cleats, etc of Grade Fe 410-W (Gde-E-250) Quality - A, includng welding or riveting etc, complete all as specified and as directed.

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

M&L for Preparation of new steel and iron surfaces of any description, n.exc 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

M&L preparation of old painted surfaces of steel surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished flat surface of concrete, complete all as specified and as directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions square or rectangular for rough finished flat surface of concrete, complete all as specified and as directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surface of oncrete, complete all as specified and as directed.

Use and waste formwork to chullah hoods, chajjas, troughs and similer items including edges for rough finished flat surface of concrete, complete all as specified and as directed.

Use and waste of formwork to soffits of suspected slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizonal or slopping) for rough finished flat surfaces of concrete, complete all as specified and as directed.

Use and waste of formwork to Fins, louvres, fascia for rough flat surfaces of concrete, complete all as specified and as directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished flat concrete surfaces, complete all as specified and as directed.

M&L for cement concrete in foundation filling and mass concrete type D2 (1:4:8) using 40 mm graded crushed stone aggregates, complete all as specified and directed.

M&L for reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggrgates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and as directed.

M&L for reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggrgates) as in columns, pillars, piers, posts and struts, complete all as specified and as directed.

M&L for reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggrgates) as in beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and as directed.

M&L for reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggrgates) as in chajjas, complete all as specified and as directed.

M&L for reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggrgates) as in slabs supported on walls, beams and columns in floors, roofs, andings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed.

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc, complete all as specified and as directed.

All as per item No 106 above but 6mm to 8mm dia TMT bars.

M&L TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc, complete all as specified and as directed.

M& L for Sand cushioning in trenches for cushioning of paver block or underground cable including spreading, levelling, well ramming in layers , complete all as specified and directed.

M&L for hardcore of broken stones or boulders of gauge not exc 63 mm, deposited, spread and levelled in layers not exc 15 cm thick, watered & rammed to a true surface, complete all as specified and directed.

M&L for 75 mm thick PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregates) as in flooring and finishing cement concrete surfaces even and fair/rough, complete all as specified and directed.

M&L for providing 75mm thick PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate) as in plinth protection, surface finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of 3:1, complete all as specified and directed.

S&F Vitreous China Wash Down Water closet (Pedestal Pattern) 1st quality, , white (excluding flushing cistern & flush pipe) including plastic water closet seat white, closed pattern with flat bottom and cover and mild steel CP or aluminised huiging device, making connections, complete all as specified and as directed.

S&F vitreous china, 1st quality, squatting pan, Orrisa pattern of size 580 X 440mm, white with integral foot rests, 'P' trap including making connection to trap, flush pipe, anti-syphonage pipe etc, complete all as specified and directed.

S&F cast iron 'S' trap, including jointing with solvent cement of 100mm dia, complete all as specified and directed.

S&F vitreous china urinal, 1st quality, Half Stall Type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified and directed.

S&F 15mm bore CP Urinal spreader for urinals, complete all as specified and directed.

S&F PVC valveless, double syphonic action type, flushing cistern, low level of 10 Litres capacity, white, with and including inlet, ball valve, float, 32mm dia flush pipe of polyethylane of low or high density or PVC, flushing bend & handles, also including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet & making connections, complete all as specified and as directed.

S&F vitreous china wash basin, 1st quality, white, flat back, approx size 510x410mm excluding taps but including 32 mm bore brass chromium plated waste fittings, cromium plated CP fancy type 15mm bore pillar tap, 32mm bore PVC waste pipe, MS brackets, complete all as specified and as directed.

S&F PVC connection 15 mm size with PTMT nuts of length 600 mm, complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank 500ltrs capacity, ISI marked, (cylindrical vertical type double-layered) with closed top including inlet,outlet and wash out holes, provision of G.I Fittings for fixing of the inlet, outlet and washout pipes, hoisted in position, complete all as specified and as directed.

S&F Ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, screwed for iron pipe of 20mm bore (Minimum weight 455 grms), complete all as specified and as directed.

S&F bib tap, fancy type, long swan neck, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and as directed.

S&F angle stop cock, fancy type, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed.

S&F CP grating of size 100mm dia, complete all as specified and as directed.

S & F health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and as directed.

S & F toilet paper holder with flat recessed type stainless steel, complete all as specified and as directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed.

S&F tubular towel rail, 20mm dia, D type, brass chrormium plated, 600mm long between flanges, complete all as specified and as directed.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. and including 15mm thick CM 1:4 screed bed, including rounding / moulding the edges half round, complete all as specified and directed.

M&L for 100 mm thick PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregates) as in flooring and finishing cement concrete surfaces even and fair/rough, complete all as specified and directed.

M&L for 75 mm thick PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregates) as in flooring and finishing cement concrete surface even and smooth without using extra cement, complete all as specified and directed.

M&L for Brickwork with Sub class 'B' old size bricks of class designation 75 (i.e average compressive strength 75 Kg / cm2), straight or curved on plan exc 6m mean radius, built in CM 1:6, complete all as specified and directed.

M&L for brick work with Sub-class 'B' Old size of class designation 75 (i.e of average compressive strength 75 Kg/cm2 ) straight or curved on plan to any radius as in half brick thick walls, built in CM 1:4, complete all as specified and as directed.

M&L for brick work with Sub-class 'B' Old size of class designation 75 (i.e of average compressive strength 75 Kg/cm2 ) in one brick thick honey comb wallings, built in CM 1:6, complete all as specified and as directed.

M&L for brick work with Sub-class 'B' Old size of class designation 75 (i.e of average compressive strength 75 Kg/cm2 ) in half brick thick honey comb wallings, built in CM 1:4, complete all as specified and as directed.

M&L for loose filling with broken bricks aggregates of gauge 80 to 150 mm in soakage pits, soakage wells, complete all as specified and directed.

S&F cast iron work grade FG 150, (article n. exc 5Kg each) unmachined, in brackets, gully traps, gratings, railing, frames, manhole covers, fire and soot doors, dampers, stop valve boxes, gate stops, parts of ranges, balusters and similar articles, complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates for 150 mm bore pipes as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, complete all as specified and as directed.

M&L for 150 mm bore SGSW pipe, grade 'A', laid in trenches including jointing with cement mortar, complete all as specified and directed.

M&L for Pre-cast reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggrgates ) as in landing, cover slabs (for manholes etc), chulla hoods, chajjas, water trough, shelves and similar article with plain faces including form work, complete all as specified and as directed. Note:- Reinforcement shall be measured and paid for seperately.

Taking down carefully existing aluminium point wiring (light / fan / socket or power point) complete, with all fittings such as switch socket combination, switches, sockets, regulator, ceiling rose, utility light fittings and lamp holders etc and making good the disturbed surfaces of walls, roof and floor etc to match with the existing specification, complete all as specified and as directed.

Material and labour for point wiring for one light point/one fan point controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia, (also including conduit fittings & PVC Junction boxes etc, along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, connected to earth dolly and to be terminated in and including factory made pressed steel sunken boxes (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm), concealed type with and including 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc, testing on completion also including cutting chases for concealed conduit, steel boxes etc, pinning in, making good the surfaces in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per Item No 144 above but for one switch socket outlet, 5 Amp on independent board all as specified and as directed.

All as per item No144 here-in-before but for one socket with other switch/switch socket outlet 5 amps on the same board, complete all as specified and as directed

All as per item No 144 here-in-before but for one15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLSH) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, complete all as specified and as directed.

Material and labour for point wiring for one light point controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable 1100 Volts grade drawn in and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia, fixed on the surfaces of wall, ceiling etc with & including all accessories, fittings, PVC junction Boxes etc, also including 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, connected to earth dolly and to be terminated in and factory made Modular Metal Flush Box with modular white cover plate and Frame suitable for modular switches, sockets, fan regulators etc, testing on completion, making good the surfaces in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per Item No 148 above but for one switch socket outlet, 5 Amp on same board all as specified and as directed.

All as per Item No 148 above but for one switch socket outlet, 5 Amp on independent board all as specified and as directed.

All as per item No 148 here-in-before but for one 15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLSH) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, complete all as specified and as directed.

Supply and fixing switch piano flush type, single pole, one way, 5 amps, complete all as specified and as directed.

Supply and fixing switch socket combination, 2 in 1, 5 Amp, flush type, complete all as specified and as directed.

S&F socket outlet 2 in 1, 3 pin, 5 Amps, flush type, complete all as specified and as directed.

S&F switch socket combination multipurpose, 3 pin, 15 amp, flush type, universal, complete all as specified and as directed.

S&F ceiling rose, 3 phase /PVC/Polycarbonate, isolated body, complete all as specified and as directed.

S&F Modular switch 1 way 6A, 1 module, complete all as specified and directed.

S&F switch 1 way 16A, 1 module, complete all as specified and directed.

S&F Modular socket 6A , 2/3 pin combined, 2 module, complete all as specified and directed.

S&F Modular socket 6A/16A , 2/3 pin combined, 2 module, complete all as specified and directed.

S&F Modular Fan step regulator, 120W, 2 module, complete all as specified and directed.

S&F LED tube light batten 1x 20W (4 feet long) surface and wall mounted , indoor luminaries with and including electronic driver and LED lamp including provision of twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and directed.

S&F Building Security light luminiar fitting 1x30W, presure die-cast aluminium housing with individual LEDs as light source and Lens embedded PC cover having TOP opening, separate driver compartment with IP 66 protection and impact resistance of IK-07 and provision of copper conducor cable for connection and GI bracket medium grade bent to shape, complete all as specified and directed.

S&F LED tube light batten 1x 10W (2 feet long) extruded aluminium housing surface and wall mounted , indoor luminaries with and including electronic driver and LED lamp including provision of twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and directed.

S&F LED lights fitting 1x 20W, 220V, AC decorative box type aluminium housing with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rosep including provision of twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and directed.

S&F angular type Lamp holder, PVC/Polycarbonate type with back plate, also with & including 12W LED Lamp, inveter type, complete all as specified and directed.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm and provision of PVC copper conductor cable for making connection with ceiling rose, complete all as specified and as directed.

Taking down existing unserviceable distribution board, switch fuse unit, enclosure for MCB / DB (inclusive of MCBs etc of any type and capacity) and making good the disturbed surfaces all as specified and as directed.

S&F sheet metal enclosure for MCBs DBs, Double Door, phosphatised, Powder coated , Single pole and Neutral (SPN), 240 Volts, 12 Ways, with and including common bus bar, complete all as specified and as directed.

S&F sheet metal enclosure for MCBs DBs, Double Door, phosphatised, Powder coated , Single pole and Neutral (SPN), 240 Volts, 4 Ways, with and including common bus bar, complete all as specified and as directed.

S & F MCB, 'C' Series, SPN, 415 volts, 6 to 32 Amps, ruputring breaking capacity 10KA, complete all as specified and directed.

S & F MCB, 'C' Series, SP, 415 volts, 6 to32 Amps, ruputring breaking capacity 10KA, complete all as specified and directed.

Material and labour for sub main wiring with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLHS cable of size 6.0 sqmm and one single core PVC insulated (unsheathed) multi stranded copper conductor FRLHS cable of size 6.0sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 25 mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces and including taking down old one, complete all as specified and as directed. Note For Items No 173 to 174:- For payment purposes, 2 runs of main cable (each of 1RM) 1 run of earth continuity cable (1RM) and one run of conduit (1RM) all together shall be considered as "1RM".

Material and labour for sub main wiring with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLHS cable of size 4.0 sqmm and one single core PVC insulated (unsheathed) multi stranded copper conductor FRLHS cable of size 4.0sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 25 mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces and including taking down old one, complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation,laying of cable, pipe etc. or for shafts, wells, cesspits, manholes, pier holes, etc. nexc 10 sq m on plan and n exc 1.5 m in depth and getting out, complete all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out, complete all as specified and directed.

All as per item No. 176.00 above but depth exceeding 1.50 metre and not exceeding 3.00 metre.

Returning, filling in, including spreading, watering and well ramming in layers not exc 25cm thick in layers, complete all as specified and directed.

Removal of surplus spoil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point, complete all as specified and directed.

Dismantling of ACSR or AAC conductor and including service cable , complete all as specifed and directed.

Dismantling of cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, complete all as specified and directed.

Dismantling of insulators of any grade, description and size from the poles etc, complete all as specified and directed.

Taking down of any size/ type service cable, complete all as specified and directed.

Supplying, laying, jointing and testing XLPE insulated, armoured, heavy duty, electric cable with stranded aluminium conductor 1100 volts grade, cross sectional area 6 Sqmm x 2 core in trenches /along poles/on wall etc, complete all as specified and as directed Notes : - (i) Excavation and earth work, sand cushioning, protection covers shall be measured and paid for separately. (ii) Unless otherwise directed by the GE, the cable shall be procured by the contractor in single length (as manufactured) to meet the actual length of cable as required at site. However, for payment purpose, the length actually ordered & laid shall be measured and paid for.

All as per item No 184.00 here-in-before but LT Cable of size 10 Sqmm x 2 Core.

All as per item No 184.00 here-in-before but LT Cable of size 16Sqmm x 2 Core.

All as per item No 184.00 here-in-before but LT Cable of size 16 Sqmm x4 Core.

All as per item No 184.00 here-in-before but LT Cable of size 25 Sqmm x 3.5 Core.

All as per item No 184.00 here-in-before but LT Cable of size 35 Sqmm x 3.5 Core.

All as per item No 184.00 here-in-before but LT Cable of size 50 Sqmm x 3.5 Core.

All as per item No 184.00 here-in-before but LT Cable of size 70 Sqmm x 3.5 Core.

All as per item No 184.00 here-in-before but LT Cable of size 95 Sqmm x 3.5 Core.

All as per item No 184.00 here-in-before but LT Cable of size 120 Sqmm x 3.5 Core.

All as per item No 184.00 here-in-before but LT Cable of size 150 Sqmm x 3.5 Core.

All as per item No 184.00 here-in-before but LT Cable of size 240 Sqmm x 3.5 Core.

Material and labour for well burnt Sub-class 'B' old size bricks, best quality locally available laid flat, dry in trenches for cable protection, complete all as specified and as directed.

Supply and fixing GI tubing, light grade, 50mm bore for protection of cable under road crossing, across drain, along electric pole or floor /wall etc, complete all as specified and directed. Note for Item No. 197 to 199: Excavation & Earthwork/Boring/ Drilling shall be measured & paid for separately. However the cost for provision of clamps made from mild steel flat of required size, bolts, nuts, washers etc (including painting of mild steel surfaces with 2 coats of aluminium paint over 1 coat of red oxide primer) for fixing of G.I. pipes with poles etc shall be deemed to be included in the quoted rate of above item.

All as per item No 197 above but 40 mm bore tubing.

All as per item No 197 above but 80 mm bore tubing.

Boring/Drilling (horizontally) using ultrasound technique and necessary machine for passing 40mm to 80mm bore pipe for protection of the cable at 1 metre depth in soil below existing road, pavement, hard standing etc without damaging the existing surfaces, getting out & disposal of soil to a distance not exceeding 50 metre from the site of work, complete all as specified and directed. Note : Cost for provision of pipes & cable not included in the scope of above item.

Supply, providing and testing PVC Insulated, weather proof, FRLSH, PVC sheathed cables with multistranded bright annealed copper conductor of size 1.5 Sqmm 3 core for connection of light fittings to RCC pole light junction box, cable laid through PVC conduit pipe of 20mm dia, heavy grade duly fixed on RCC pole with provision of suitable MS clamps, bolts, nuts etc, complete all as specified and directed.

Supply, providing and testing PVC Insulated, weather proof, FRLSH, PVC sheathed cables with multistranded bright annealed copper conductor of size 1.5 Sqmm 3 core for connection of light fittings to Steel pole light junction box, cable laid through steel pole & including driling work for making hole wire entry in steel pole, complete all as specified and directed.

S&F in repair and testing of factory made thermoplastic weather proof, junction box of size 205(L) x 255 (B) x 112 (D) mm with IP-65 protection having 01 Number DIN Rail for mounting of MCBs also provided with 01 Number MCB, SP, 6 Amps, 10 KA breaking capacity, "C" curve & two openings with & including cable glands for termination of cable & fixing with the provision of MS clamps of size 20x3mm with nuts bolts and washers etc to poles, complete all as specified and as directed

Supply, Installing, Testing & Commissioning of CPRI type tested, double door, out door, pedestal type, of suitable size to accomodate all of its components, accessories, items, factory fabricated & factory assembled, out of 3.15mm thick CRCA sheet, supporting frame made out of 50x50x5mm (minimum size) angle iron & MC 100mm (minimum size) in base, all the steel surfaces (internally as well as externally) shall be duly pre-treated with anti-corrosive coating & finally epoxy powder coated of tint grey-shade (RAL-7032), double door, front & back openable with locking arrangement, 4 side slanting canopy on roof top, the panel shall be having ventilation facility with provision of louvers for better heat dissipation, the panel shall be provided with suitable neoprene rubber gasket to make it completely weather, dust & vermin proof & degree of protection not less than IP-54, the panel shall have independent housing for each control switch gear & shall be accommodated with & including bus-bars, the panel shall be suitable for 3 Phase, 4 wire system, 50Hz, 415/440 volts grade electric supply, duly provided with multistraded internal wiring with not less than 2.5 sqmm copper conductor wire (with & including copper lugs of suitable sizes), also including providing PCC 1:3:6 (type-C2 using 40 mm graded crushed stone aggregates) as in foundation, minimum height of plateform is 0.4m , necessary excavation & earth work and also provided with the following accessories, components, items complete all as specified and directed.:- (A) BUS BARS AND INTERNAL CONNECTIONS : The bus-bars shall be made up of pure copper conductor, 200 Amps rated; 04 Nos for phases and Neutral, duly insulated with 1100 Volts grade, heat resistance & fire proof (HFFR), heat shrinkable, standard colour coded, sleeves & rigidly mounted on suitable sized "F" class epoxy insulators, non-hygroscopic, non-combustible, all internal connections from main bus-bars to MCCB's etc. (B) PROVISION FOR CABLE ENTRY/EXIT : Openings for cable entry/exit with & including cable grlands & copper lugs shall be provided in the bottom of panel for both incoming & out-going cables.

M&L for Earthing complete with galvanized steel earth plate electrode 600 mm X 600 mm X 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, PCC (1:3:6) type C-1 with 50 mm thick Pre-cast RCC (1:2:4) type B-1 cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (medium grade), wire mesh, aluminium lugs, complete in all respect, GI earth strip protected by 40 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 m and necessary testing on completion, complete all as specified and as directed.

M&L for Earthing complete with galvanized steel earth plate electrode 600 mm X 600 mm X 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, connected to galvanized iron strip 25x4mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, PCC (1:3:6) type C-1 with 50 mm thick Pre-cast RCC (1:2:4) type B-1 cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (light grade), wire mesh, aluminium lugs, complete in all respect, GI earth wire protected by 40 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 m and necessary testing on completion, complete all as specified and as directed.

M/S JYOTI SHARMA AND SONS

M/S R. K. INDUSTRIES

M/S SEN CONSTRUCTION

M/S AHUJA TRADING