Civil Works Maintenanace Contract

Amount

DISMANTLING PLAIN CEMENT CONCRETE manually / by mechanical means carefully without damaging adjacent structures including disposal of debris within 200m lead as per direction of Engineer-in-charge.

DISMANTLING BRICK WORK in cement mortar carefully without damaging adjacent structures including stacking of materials and dispoal of unserviceable materials within 100m lead as per direction of Engineer-in-charge.

DISMANTLING OF RCC WORKS carefully manually without damaging adjacent structures excluding cutting of reinforcement including stacking of steel reinforcement bars and disposal of unserviceable materials within 200m lead as per direction of Engineer-in-charge.

DISMANTLING BRICK BAT COBA CEMENT BASED WATER PROOFING over roof and chajjas carefully with out damaging adjecent structures including lowering and stacking of materials and dispoal of unserviceable materials within 200m lead as per direction of Engineer-in-charge.

DISMANTLING OLD PLASTER OR SKIRTING carefully, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 100m lead.

DISMANTLING TILE WORK IN FLOORS AND ROOFS laid in cement mortar including stacking material within 100m lead for thickness of tile up to 25mm etc. complete as directed by Engineer in charge.

DISMANTLING TILE WORK IN FLOORS AND ROOFS laid in cement mortar including stacking material within 100m lead for thickness of tiles above 25mm and up to 40mm.

Labour charges for DISMANTLING EXISTING SHAHBAD STONE PAVEMENT OR PAVER BLOCK PAVEMENT AND RE-LAYING in footpaths, in Plinth Protection etc. carefully without damaging and re-laying the same over a bed of stone grit 150mm consolidated thickness, to proper slope, including cutting the edges to proper lines and sunk pointing with Cement mortar 1:3 with 15mm x 10mm groove cross wire and longitudinally and curing etc. complete. (Grit to be provided by the Contractor)

DISMANTLING KERB STONE AND RE-FIXING carefully without damaging the stone, including removal of earth, base PCC etc. and refixing the same in line and level on newly laid base PCC 1:3:6 and pointing the exposed faces in cement mortar 1:3, curing etc. complete as directed by the Engineer in charge. The rate shall also include charges for disposal of unserviceable materials within 50m lead. The base PCC laid shall be paid separately under relevant item.

Earth work in SURFACE EXCAVATION not exceeding 30cm in depth but exceeding 1.5m in width as well as 10 sq.m on plan area in all types of soils except soft and Hard rock, including disposal of excaved earth up to a distance of 50m. Disposed soil to be levelled and neatly dressed all as per specifications and as directed by the Engineer-in-charge.

LEAD CHARGES FOR LEAD OF DEBRIS BEYOND 4KM BUT UP TO & INCLUDING 30KM by mechanical transport includinmg loading,unloading, stacking / levelling etc. The rates are applicable for NET Quantities arrived after making deduction for voids @ 30% from corresponding TRUCK Measurement. Note: Finding authorised ground for disposing debries, trasporting of debries at disposal ground, disposing, stacking, leveling & statutery charges if any will be responsibility of the Contractor and no extra charges shall be paid for the same. The debris from identified area shall be cleared every week after accumulation of minimum One Track Load.

Supplying, stacking and laying of 230mm THICK RUBBLE SOLING STONES as under floor base including packing with smaller stone and compacting, ramming including spreading and consolidation of blinding material, moorum etc. complete all as per specifications and as directed by the Engineer-in-charge.

Providing and laying in position CEMENT CONCRETE OF 1:3:6 (1 cement, 3 crushed sand, 6 graded stone aggregate of maximum size 20mm) including consolidation, finishing, curing etc. complete as per specificationsand drawings but excluding the cost of Form work shuttering, centering Complete at all levels.

Providing, centering, shuttering FORM WORK USING PVC FILM FACED PLYWOOD to get a neat form finish surface for all types of structures including necessary strutting, proping, staging, supports etc and deshuttering the same after the specified time all as per drawings and specifications at all levels and as directed by the Engineer-in-charge.

Providing and laying in position CEMENT CONCRETE OF 1:2:4 (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size 20mm) including consolidation, finishing, curing etc. complete as per specification and drawings but excluding the cost of Formwork shuttering, centering and steel reinforcement at all Levels.

Providing and laying in position REINFORCED CEMENT CONCRETE (RCC) OF GRADE M-30 using 20mm maximum size aggregates and crushed sand of approved quality including admixtures of approved brand and quality (plasticiser or superplasticiser) if required, including weigh batching, mechanical mixing, transporting, placing, vibrating, consolidation, finishing, curing etc.complete but excluding the cost of centering, shuttering and reinforcement complete as per specifications up to Plinth Level and as directed by the Engineer-in-charge.

Providing REINFORCEMENT FOR REINFORCED CEMENT CONCRETE at all levels including supplying, preparation of bar bending schedules,cutting, bending, transporting, fixing, tieing in position with 1.6 mm dia soft drawn annealed binding wire all labour charges, cost of cover blocks in specified grade of concrete etc. complete including cost of binding wire as per specifications and drawings. Steel Supplied by the Contractor. Using TMT bars of specified grade all dia bars to be supplied by the contractor manufactured by other than SAIL, RINL or TATA and approved brands of BARC only.

Providing STRUCTURAL STEEL WORK USING ANGLES, CHANNELS, JOISTS AND OTHER SECTIONS, welded and / or bolted in built up sections for trusses , structural steel floors, frame works, monorails and other structures including supplying, cutting, welding, fabricating, hoisting, fixing in position, applying a priming coat of approved steel primer etc. complete all as per specifications, drawings and as directed by the Project Engineer. Up to and including 300mm Joists, 350mm channels, and below sections using materials of approved manufacturers. (ISI marked other than SAIL / RINL) All test reports to be provided along with the supply of the materials.

Providing and Fixing 16mm diameter & 200 mm Long ANCHOR FASTNER of approved make including drilling in concrete as per requirement for fixing EPs or other structures all as specified by the manufacturer complete all as per specifications and drawings or as directed by Engineer-in-charge.

Only supplying 16MM DIAMETER & 200MM LONG ANCHOR FASTNER of approved make as directed by Engineer-in-charge.

Making the OPENING IN BRICK MASONRY FOR DOOR / WINDOW / CLEAR STORY OPENING including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete to match existing surface including disposal of mulba/ rubbish to the nearest dumping ground.

Providing and constructing BRICK WORK in cement mortar using Standard bricks of approved quality / class, make / brand in super structure above plinth up to Floor-II level in all shapes and sizes including curing, raking out joints complete as per specifications and as directed by the Engineer-in-charge. Brickwork in super structure with standard bricks in C.M 1:4 using crushed sand.

Providing and laying AUTOCLAVED AERATED CEMENT BLOCK MASONRY of approved make with specified thick AAC Blocks in Super structure above plinth level up to 20m height in cement mortar 1:4 (using crushed sand). The rate shall also include providing and placing in position 2 Nos of 8mm dia bars at every third course of the masonry work.

Providing 15mm THICK INTERNAL PLASTER as back coat in cement mortar 1:4 without cement punning (using Crushed Sand) finished smooth, including sieving of sand to required fineness, preparation of the surface, scaffolding, curing all as per specifications, drawings and as directed at site complete.

Providing 20mm THICK INTERNAL PLASTERING in C.M without cement punning 1:4 (using Crushed Sand) finished smooth, including sieving of sand to required fineness, preparation of the surface, scaffolding, curing all as per specifications, drawings and as directed at site complete.

Providing 20mm THICK EXTERNAL PLASTERING in two coats under layer 12mm thick with C.M 1:4 (using crushed sand) finished with a top layer 8mm thick in C. M 1:3 (using crushed sand) including approved water proofing compound @ 2% by weight of cement or as per manufacturer's specifications, sieving of sand to required fineness, scaffolding up to 10m height, finishing, curing etc. complete as per specifications. and as directed by the Engineer-in-charge.

Providing 20mm THICK PLASTERING USING READY MIX EXTERNAL PLASTERING COMPOUND of approved make for external faces of brickwork / concrete surfaces including preparation of the surface, curing, finishing to match with old surface, cleaning, complete. all as per specifications including forming drip moulds wherever necessary and as directed by the Engineer-in-charge.

Providing and constructing RANDOM RUBBLE MASONRY using approved Rubble stone in foundation and plinth in C.M 1:6 (using crushed sand) including raking out joints or simultaneous flush pointing below ground level / plinth level, curing etc. complete as per drawings and specifications.

Providing FLUSH POINTING on stone masonry with cement moratr 1:3 using river sand as per specifications and as directed at site by the Engineer-in-charge

Providing RAISED & CUT POINTING on stone with cement moratr 1:3 using river sand as per specifications and as directed at site by the Engineer-in-charge

Providing STRUCTURAL REPAIRS IN OLD DAMAGED CONCRETE STRUCTURES / SURFACES WITH APPROVED POLYMER with following operations:- 1) Removal of loose/Spalled or damaged concrete by chipping and cleaning the concrete surface and reinforcement steel with wire brush and with water 2) Cleaning the re bars with Acetone for complete rust removal and washing with water to make the surface clean. 3) Applying protective coat / bond coat using polymer and cement in the proportion of 1; 1.5 (1 part of polymer and 1.5 parts of cement in synthetic enamal paint like consistancy with brush 4) Reinstate the area with polymer modified mortar in layers of maximum 20mm with the proportion of Cement 50 Kg : washed and dried river sand 87.50 kg : silica sand 37.50 Kg. mixed with 10 litres of Polymer (or 1 Kg cement : 1.75 kg washed and dried river sand : 0.75 Kg silica sand : 200 ml polymer) 1.00 Lit 609.00 671.005) If thickness of repair exceeds 20mm , after every 20mm thick repair, bond coat as per 2 above to be applied and further thick of repair to be continued for each layer. This work is inclusive of all materials, labour, complete all as directed at site using approved polymer suitable for structural repair shall be used) Note: Scaffolding will be paid separately under relevant item.

Providing and fixing DOUBLE TUBULAR SCAFFOLDING SYSTEM using H- frames with cup lock type on the exterior side upto seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre horizontal and vertical tubes joining with cup and lock system with M.S. tubes, M.S. tube challies, M.S clamps and M.S staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connection with building etc. wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and as approved by the Engineer -in - charge. The elevational area of the scaffolding shall be measured for payment purposes. The payment shall be made once irrespective of duration of scaffolding

Providing and laying WATER PROOFING TREATMENT IN SUNKEN PORTIONS of WCs, BATH ROOMs etc. by appying cement slurry mixed with water proofing cement compound consisting of applying: (a) 1st layer of slurry of cement @ 0.488 kg / sq.m mixed with water proofing cement compound @ 0.253 kg per sq.m. including injecting cement layer of slurry of cement @ 0.242 kg / sq.m mixed with waterproofing cement compound @ 0.126 kg / sq.m. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with cement slurry. Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (using crushed sand) admixed with proprietary water proofing compound conforming to relevant IS and approved by Engineer-in-charge including mixing 'RECRON 3S' fibre at the rate of 125 grams per 50 kg of cement in top layer of plaster and finally finishing the surface with trowel with neat cement slury in bottom and all the sides of sunken portion.complete as directed by the Enginer-in-charge. The treatment to be tested for water tightness before filling the sunken areas. Note: 1. The waterproofing treatment is to be Guaranteed for bone dry condition for a period of 10 years. 2. The cement required for the treatment is to be supplied by contractor 3. The measurement for payment shall be the actual area covered by the treatment.

Providing and fixing 1st quality CERAMIC GLAZED FLOOR TILES of minimum 300 - 600 mm long and 300 - 600 mm wide and thickness not less than 6 mm conforming to IS 15622 of approved make in all colours and shades as approved by Engineer-in-charge over a bed of 20 mm thick bed of cement mortar 1:4 (using crushed sand) and jointing with grey cement slurry including pointing with white cement based Tile grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Enginner-in-charge.

Only supplying 1st quality CERAMIC GLAZED FLOOR TILES of minimum 300 - 600 mm long and 300 - 600 mm wide and thickness not less than 6 mm conforming to IS 15622 of approved make in all colours and shades as approved by Engineer-in-charge.

Providing and fixing 1st quality CERAMIC GLAZED WALL TILES conforming to IS 15622 of approved make. shade and colour of size ranging from 300 - 600 mm long and 300 mm - 600 mm wide and thickness not less than 6 mm as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (using crushed sand), setting the tiles in cement slurry and pointing the joints with matching colour Tile grout of approved make of matching shade including using PVC tile trim in the exposed corners, complete as per drawings, patterns and specifications complete as directed by the Engineer-in-charge.

Only supplying 1st quality CERAMIC GLAZED WALL TILES of minimum 300 - 600 mm long and 300 - 600 mm wide and thickness not less than 6 mm conforming to IS 15622 of approved make in all colours and shades as approved by Engineer-in-charge.

Providing and laying minimum 25mm THICK UNIFORM SHADE KOTAH STONE FLOORING over 20 mm thick (Avearge) base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing in minimum three levels to obtain mirror polish complete with base cement mortar 1:4 (using crushed sand) all as per specifications, patterns and drawings complete.

CUDDAPAH STONE SLAB OVER KITCHEN PLATFORM etc. using 25 mm to 30 mm thick machine cut double machine polished slabs in single piece upto a maximum length of 1.80 metres laid over 20 mm thick cement mortar bedding 1:4 finished to proper levels, cured etc. complete.

Providing and fixing Minimum 17 mm thick gang saw cut mirror polished (Premoulded and Prepolished) machine cut GRANITE OF TELEPHONE BLACK COLOUR FOR KITCHEN PLATFORMS, vanitiy counters, Wash basin Counters, Door Frames, window sills, facias and similar locations of required size, colour and texture laid over 20 mm thick base cement mortar 1:4 (using crushed sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edges to give high gloss finish etc. complete as directed by the Engineer-in-charge at all levels.

Extra for providing EDGE MOULDING TO 17mm THICK MARBLE STONE / GRANITE SLAB counters, Vanitis etc. including machine polishing to edge to give high gloss finish et. Complete as per design approved by Engineer-in-charge. Granite work

Providing, supplying, and fixing DESIGNER CONCRETE TILES USING "SUPERTILES" OR "ULTRA" make or approved equivalent make of approved pattern & colour for Pathways / Stair treads / Risers over 20 mm thick Cement mortarCement mortar 1:4( using manufactured sand) setting with cement slurry including cleaning the tiles free from Mortar, dirt etc. complete all as directed by Engineer in charge.( sample to be got approved by the engineer incharge)

Using 38 mm thick tiles for pathways & treads (500x250mm)

Using 18 to 20 mm thick tiles for risers( 600x 150 mm)

Providing and Fixing HOMOGENEOUS 2.00mm THICK PVC SHEET / TILE IN FLOORING AND SKIRTING of approved make in approved pattern on a smooth and damp proof base using rubber based adhesive of approved quality and manufacturer including, levelling small undulations with plasterof paris if required , rolling with light wooden roller weighing about 5 kg all complete as directed by Engineer-in-charge in approved colour and shade

Only supplying HOMOGENEOUS 2.00mm THICK PVC SHEET / TILE FOR FLOORING AND SKIRTING of approved colour and shade, approved make & approved quality as directed by Engineer-in-Charge.

Providing and fixing GLAZED VITRIFIED FLOOR TILES of size 600 X 600 mm in floor and dado of approved make in different sizes conforming to IS 15622 in all colours and shades in Glossy or Matt or satin finish laid over a bed of minimum 20 mm thick bed of cement mortar 1:4 (using Crushed sand) and jointing with grey cement slurry including grouting with the joints with white cement based Tile Grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge

Only supplying GLAZED VITRIFIED FLOOR TILES of size 600 X 600 mm for floor and dado of approved make, colours and shades in Glossy or Matt or Satin Finish as directed by the Engineer-in-Charge.

Providing and laying FLOORING PLASTER OF PARIS 8mm THICK OVER NEW LAID TILES including spreading polythene paper, curing, levelling,removal and disposal of same before cleaning floor, labour, tools etc. complete and as directed by Engineer in charge.

Providing and laying SELF LEVELLING EPOXY FLOORING 3MM THICK, including preparation of the surface, primer coat, screeding & levelling coat and finishing coat with Polyuretane coat of approved colour and shade manufactured by M/s. Cipy Polyureathane or approved equivalent all as per manufacturers specifications complete as directed at site ( This Job to be carried out through a specialised approved agency sample work to be executed and got approved by the Project engineer).

Extra Charges for 75mm x 75mm COVING AT CORNERS

DISMANTLING DOORS, WINDOWS AND CLEAR STOREY OPENINGS (steel / wood) shutter including chowkhats, architraves, holdfasts etc. complete and stacking within 100m lead (full windows) of area 3.00 Sq.M and below.

DISMANTLING DOORS, WINDOWS AND CLEAR STOREY OPENINGS (steel / wood) shutter including chowkhats, architraves, holdfasts etc. complete and stacking within 100m lead (full windows) of area beyond 3.00 Sq.M.

DISMANTLING ALUMINIUM / GYPSUM PARTITIONS, DOORS, WINDOWS, fixed glazing and false ceiling including disposal of unserviceable surplaus material and stacking of serviceable materials within 100 m lead as directed by the Engineer-in-charge.

LABOUR CHARGES ONLY FOR RETRIEVING WOODEN DOOR SHUTTERS FROM FRAMES (Chowkhat) of various sizes, modifying, taking out damaged ply from the doors, replacing/bonding 3mm thick marine ply with suitable synthetic resin, plywood, including cost of fevicol, synthetic resin, tools, tackles, nails, screws etc. all complete and refixing the same after complete repairs, re-sizing & refixing fittings, fixtures such as tower bolts, aldrop, door handle, baby latch, mortice locks, night latch, hinges etc. (shall be paid separately under relivent item of this tender schedule ) etc. all complete for shutters including minor repairs to chowkhats, architraves, etc. as per site conditions and as directed.

Door frames with shutter of sizes up to 3 Sqm.(Single shutter)

Door frames with shutter of sizes above 3 Sqm.(Double shutter)

Providing WOOD WORK IN FRAMES OF DOORS, WINDOWS, CLEAR STORY OPENINGS and other frames, wrought framed and fixed in position of required size and shape including sawing, jointing,making rebates for shutters, making grooves as shown in the drawings, finishing the surfaces to the required finish all as per specifications and drawings including necessary MS hold fasts 40 mm X 3 mm thick, 200 mm long / with coach screws including protective painting to the suface that will come in contact with walls, joining materials, labour etc. complete all as per specifications and as directed by the Engineer-in-charge. Using Second class teak wood only.

Only supplying WOODEN FRAMES OF DOORS, WINDOWS, CLEAR STORY OPENINGS of required size and shape including sawing, making rebates / grooves for shutters, finishing the surfaces to the required finish all as per specifications as directed by the Engineer-in-Charge. Using Second class teak wood only.

Providing and fixing 35mm THICK FLUSH DOOR SHUTTERS conforming to IS : 2202 non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with internal teak wood lipping 25mm wide and fixing with 4 Nos of 125 mm long Stainless steel Hinges with S.S. wood screws complete.

Only supplying 35mm THICK FLUSH DOOR SHUTTERS conforming to IS : 2202 non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with internal teak wood lipping 25mm wide.

Providing LOUVERED OPENING IN DOOR SHUTTERS including making the opening, providing & fixing teak wood louver blades with necessary teak wood frame work & beading & applying one coat of approved wood primer etc. complete.

Providing VISION PANEL not exceeding 0.1 sqm in all type of flush door including fixing 4 mm Clear Glass with necessary teak wood Beadings complete all as per specifications and as per Drawings.

Providing and fixing Heavy Quality MECHANICALLY OPERATED GUIDED CHANNEL WITH FITTINGS COMPLETE FOR SLIDING DOOR including roller wheel, stoper, guiding-pin etc complete of approved make as per specifications and as directed by the Engineer-in-charge.

Only supplying Heavy Quality MECHANICALLY OPERATED GUIDED CHANNEL WITH FITTINGS COMPLETE FOR SLIDING DOOR including roller wheel, stoper, guiding-pin etc complete of approved make as per specifications and as directed by the Engineer-in-Charge.

REPAIRING AND REFIXING IN POSITION THE EXISTING DAMAGED HYDRAULIC DOOR CLOSER (heavy duty No.3) involving following operations: i) Complete dismantling including removal of clamp bolt, main arm, top nut, ratchet, notch plate, removal of split oil, brass regulatory screws, spring etc. ii) Providing and fixing Evertite make (Confirming to I.S.35640) bottle type door closer spring for heavy duty door closer No. 3 brass regulatory spring No.1 Part No.1 machine oil (approx. 100 ml.) etc. Note.:- 1) The door closer repaired and spares replaced are to be handed over to Maintenance Unit for accounts. 2) The Agency may inspect the condition of door closers in premises prior to quoting. 3) The repairing and spares replacement shall stand for guarantee of six months trouble free operation with replacement of spares if any, defect occurs the same shall be attended by the Contractor.

Supplying, providing and fixing DOOR CLOSER TS 71-DORMA-STD ARM or approved equivalnet with necessary screws, fixing to the aluminium/glass/wooden door complete as per drawing, specifications including all labour, transporting charges etc. & as directed by EIC.

Providing & only supplying of DOOR CLOSER TS 71-DORMA-STD ARM or approved equivalnet M/⁠s TECMA Door closer FT1070 (Capacity 60-⁠80 Kg.) with standard lever arm, necessary screws and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable.

Providing and fixing ALUMINIUM HANDLES 175mm LONG INNER GRIP 125mm WITH 12mm DIA ROD PLATE TYPE BOW HANDLES ISI marked of approved make, anodised transparent or dyed to req. colour or shade with necessary screws etc. complete.

Providing & only supplying of ALUMINIUM HANDLES 175mm LONG INNER GRIP 125mm WITH 12mm DIA ROD PLATE TYPE BOW HANDLES and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable.

Providing and fixing ALUMINIUM TOWER BOLTS OF SIZE 250mm X 12mm of approved make with necessary screws etc.all as per specifications and as per drawings.

Providing & only supplying of ALUMINIUM TOWER BOLTS OF SIZE 250mm X 12mm and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable.

Providing and fixing STAINLESS STEEL ALDROPS OF SIZE 300mm X 14mm of approved make with necessary screws, bolting from rear side complete as per specifications complete.

Providing & only supplying of STAINLESS STEEL ALDROPS OF SIZE 300mm X 14mm and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable.

ONLY REPAIRING OF LOCK of mortise / Knight / Neki or alumunim door lock, including removal & refixing of locks with proper as per existing.

Providing and fixing 4 LEVER MORTICE LOCK of approved make suitable for aluminium sections.

Providing & only supplying of 4 LEVER MORTICE LOCK of approved make suitable for aluminium sections and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable.

Providing and fixing 6 LEVERS MORTICE LATCH AND LOCK of approved make and a pair of handles Inside opening Left / Right with necessary screws etc complete suitable for fixing in wooden / steel/ FRP/ doors as per specifications.

Providing & only supplying of 6 LEVERS MORTICE LATCH AND LOCK of approved make and a pair of handles Inside opening Left / Right and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable.

Providing and fixing ANODISED ALUMINIUM BABY LATCH of size 75 X 12 mm ISI marked of approved make transparent or dyed to requried colour or shade with necessary screws etc.

Providing & only supplying of ANODISED ALUMINIUM BABY LATCH of size 75 X 12 mm ISI marked of approved make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable.

Providing and fixing ALUMINIUM HANGING HEAVY QUALITY FLOOR DOOR STOPPER ISI marked with twin rubber stoppers, anodised transparent or dyed to required. colour or shade with necessary screws etc. complete.

Providing & only supplying of ALUMINIUM HANGING HEAVY QUALITY FLOOR DOOR STOPPER and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable.

Providing and fixing IS:1341 marked OXIDIZED M.S. HEAVY WEIGHT BUTT HINGES / PARLIAMENTARY HINGES of size 125 x 90 x 3.15 mm with necessary screws etc. complete.

Providing & only supplying of OXIDIZED M.S. HEAVY WEIGHT BUTT HINGES / PARLIAMENTARY HINGES of size 125 x 90 x 3.15 mm and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable.

Supplying, providing and fixing STAINLESS STEEL-304 D-HANDLES (MATT FINISH) OF LENGTH - 300mm, DIAMETER-25mm, suitable S.S. fange , S.S. cap and thickness 16 Guage thickness to brick Walls, R.C.C. surface, Wooden doors etc. including drilling, S.S. Screws of 30mm long ( 6 Nos for each handle) ,cost of labour, tools, tackles ,wooden gutties, plants, transportaion, scaffolding etc. all complete as per site requirement and as directed by Engineer in charge.

Providing & only supplying of STAINLESS STEEL-304 D-HANDLES (MATT FINISH) OF LENGTH - 300mm, DIAMETER-25mm and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable.

Providing and fixing WATER PROOF MARINE PLY (Kit ply, Anchor ply or equivalent) the rates are exclusive screws, washers etc complete providing and fixing hard wood leaping around board in walls etc. By using 12 mm thick water proof marine ply.

By using 8 mm thick water proof marine ply.

By using 12 mm thick water proof marine ply.

By using 19 mm thick water proof marine ply.

Only supplying WATER PROOF MARINE PLY (Kit ply, Anchor ply or approved equivalent) and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

8 mm thick water proof marine ply.

12 mm thick water proof marine ply.

19 mm thick water proof marine ply.

Providing and fixing DECORATIVE HIGH PRESSURE 1.0mm THICK LAMINATED SHEET OF PLAIN / WOOD GRAIN in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS:2046 Type S including cost of adhesive, labour etc. complete as directed by Engineer-in-Charge.

Only supplying DECORATIVE HIGH PRESSURE 1.0mm THICK LAMINATED SHEET OF PLAIN / WOOD GRAIN in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS:2046 Type S and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as directed by Engineer-in-Charge.

Supplying, Providing and fixing BEADING (ARCHITRAVE) of size 50mm to 65mm wide and 12 mm thick using 2nd class teak wood/water proof marine ply around the door frames with necessary screws and fixing laminated sheet on top etc. complete as directed by the Project Engineer.

Providing and fixing FRP DOOR SHUTTERS FLUSH DOOR / PANELLED TYPE of 35 mm thick panelled door type of approved colours including the cost of 100 mm ISI marked heavy quality stainless steel butt hinges with necessary screws with plain colour or wooden veneer finish of approved make, design & colour. made out of 1.5 mm thick FRP skin moulded over wooden frame work of 40 mm wide and required thickness wooden styles and minimum 100 mm wide lock rails and wooden blocks for door stoppers, tower bolts, baby latch, aldrop, handles etc. wherever required and core filled with Polyurethane Foam and fixing with 4 Nos 100 mm (ISI marked) stainless steel hinges with S.S. wood screws.

Providing and fixing 25mm thick SOLID PVC INTEGRAL SHEET FLUSH DOOR SHUTTER of M/s Jain Irrigation System Ltd. of white colour or as directed by Engineer-in-Charge. Made out of J1054 Integral Foam Sheet and including fixing with 4 Nos 100 mm ISI marked heavy quality stainless steel butt hinges with S.S. necessary screws.

Providing, supplying and fixing VENTILATION VERTICAL BLINDS (approved) with all accessories and fabricating to required sizes etc as per approved design and approved Fabric complete all as directed by the Project Engineer.

Providing and fixing 25 mm S.S. CURTAIN RODS of 1.25mm thick with two SS / Brass brackets fixed with SS / Brass screws and wooden plugs etc.wherever necessary complete.

Providing, supplying and fixing HOLLOW METAL FLUSH STEEL DOORS 40mm thick of approved make consisting of door frame and shutters and all hardware fittings, frame made out of 14g thick G.I sheets and shutters made of 16g thick sheets, hollow portion filled with puff, including necessary stiffners in shutters and frame, vision panel of specified size with 4 mm glass and clip on pressed steel frame for vision panels, fixing 4 nos heavy duty stainless steel 304 grade ball bearing hinges, mortise / dead lock of approved make, a pair of 200 mm long stainless steel handles, 250 mm long stailless steel tower bolt, etc. frame hollow portion filled with PCC 1:2:4, necessary hold fast embedded in concrete, fixing in concrete with anchor fastners. finished with Polyurethane painting of approved colour complete all as per drawings and specifications and as directed by the Engineer-in-charge.

Providing, supplying & fixing of S.S. MESH-(MOSQUITO NET) - 0.50MM THICK - LESS THAN 1.0 SQ. MM APERTURE in aluminium grill / frame including cost of all accessories and fabricating to required sizes etc complete all as directed by the Engineer-in-Charge. Alumunium Grill will be paid separately

Providing, supplying and fixing G.I. SQARE MESH OF 3MM THICK & LESS THAN 1.0 SQ. INCH APERTURE FITTED ON MS FRAME including cost of welding and fabricating into required sizes etc. complete as directed by the Engineer-in-Charge. MS Frame Work will be paid separately.

RESIZING OF EXISTING ALUMINIUM DOOR SHUTTER 1. Existing aluminium framed swing doors shall make floor touch free (to increase bottom clearance) by resizing it. 2. The job is involved of dismantling existing shutter totally including accessories/fittings; cutting of aluminium section as required; reassembling. 3. Existing damaged/not reusable aluminium sections shall be replaced with new ones and the same will be measured under concerned items. 4. Providing and fixing of m.s. tie rods having suitable nutt/bolts system at both ends of shutter if need. 5. Reshaping and re-fixing of existing board panel/glass sheets as required; 6. Re-erecting and repositioning the shutter as earlier. 7. Re-fixing of all fittings such as pull/push handle; hydraulic door closer; hinges; locking arrangement; tower bolts; 8. Replacing the existing damaged rubber gasket lining and aluminium clips with new ones 9. The contractor shall be provided the sundry materials such as rubber gaskets; screws, ms tie rods, etc and no extra payment will be made for these. 10. If glass panels are broken during handling, the contractor shall replace the same at no extra cost. 11. Measurements: Each shutter a size of 900 mm x 2100 mm will be measured as one job.

ALUMINIUM WORK FOR DOORS, WINDOWS, VENTILATORS & PARTITION with extruded built up standard tubular sections / Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereever required including cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless screws all complete as per drawings and and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealent etc. (fittings glazing and panelling shall be paid for separately)

Providing and fixing Aluminium sections (Minimum anodizing thickness of 15 micron)

Only Supplying Aluminium sections (Minimum anodizing thickness of 15 micron)

Extra for COLOUR ANODIZING / DYED ANODIZING

Providing and fixing GLAZING IN ALUMINIUM DOORS, WINDOW, VENTILATOR shutters and partitions etc with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-Charge (Cost of snap beading shall be paid in basic item)

With Frosted Glass panes of 5.00 mm thickness

With Clear Float Glass panes of 5.00 mm thickness

With Tinted Colour Glass panes of 5.00 mm thickness

Providing and fixing Approved Quality STAIN LESS STEEL BODY ROLLER WHEELS of approved make for Sliding shutters

Providing & only supplying of STAIN LESS STEEL BODY ROLLER WHEELS of approved make for Sliding shutters and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing Approved Quality and shape STAR LOCKS cum Handle of MIDIN or approved equivalent make for Sliding shutters.

Providing & only supplying of STAR LOCKS cum Handle of MIDIN or approved equivalent make for Sliding shutters and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing DOUBLE ACTION HYDRAULIC FLOOR SPRING of approved brand and manufacturer (conforming to relevant Indian Standard) for doors including cost of cutting floors as required, embedding in floors and cover plates with M.S pivot and single piece of M.S sheet outer box with slide plate etc. complete as per directions of Engineer-in-charge with brass cover plate

Providing & only supplying of DOUBLE ACTION HYDRAULIC FLOOR SPRING of approved brand and manufacturer (conforming to relevant Indian Standard) for doors and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providng and fixing "DECO GRILLE" make Model No. DG- 202 in natural Silver anodising of min 15 Micronswith a opening size of 60mm x 45mm and Minimum weight of 4.12 Kg/ Sq.M including providing anfd fixing Suitable 'F' / 'H' section outer frame and mullion fixing with screws complete all as per specifications and as directed at site by the Engineer-in-charge .Aluminium alloy shall be of 6063-T6 with yield strength of minimum 6.5 kg/ sq.mm.

Aluminium Grill 8 mm thick

Aluminium Grill 10 mm thick

Extra for providing ALUMINIUM GRILL 10mm THICK WITH COLOUR ANODISED by the manufacturer (Champagne, black, Bronze, Gold colours) complete all as per specifications and as directed at site by the Engineer-in-charge

Aluminium Grill 8 mm thick

Aluminium Grill 10 mm thick

FILLING THE GAP WITH SILICON SEALANT between aluminium frame & adjacent RCC / Brick work / Stone work over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete Up to 5 mm depth and 5 mm width.

Providing and fixing in position SUSPENDED FALSE CEILING SYSTEM / PARTITION SYSTEM USING CALCIUM SILICATE BOARDS (HILUX CEILING SYSTEMS) 100% humidity resistance, incombustible as per BS476 part IV with thermal conductivity of 0.043 w/m KC placed in a suspended grid of size of 600x 600mm made of hot-dipped G.I steel sections wherein the ceiling sections of 0.55 mm thick shall be suspended at 1200 mm centres along the length of ceiling with 4mm dia G.I wires/ 1 mm thick strip hangers made of G.I sheet sections with necessary level adjusters and inter channels of 0.90mm thick with connecting clips and resting on the perifery walls on wall angles of 0.55 mm thickness including providing necessary openings for light fixtures, diffusers, trap doors etc to be made as per layout drawings and as per directions of Engineer-in-charge The main tees to be suspended from the ceiling/ soffit with the help of metal dash fastners of 6mmx50mm, soffit clits of 25mmx35mmx1.60mm and 4mm dia G.I wire with galvanised spring steel levelling clips/ G.I strip Hangers at 600mm centers . the entire grid system shall be designed to bear a distributed load of minimum 25 kg/Sq.m (Only calcium silicate false ceiling area will be measured for the purpose of payment)

8mm THICK CALCIUM SILICATE BOARDS (HILUX CEILING SYSTEMS)

12mm THICK CALCIUM SILICATE BOARDS (HILUX CEILING SYSTEMS)

Providing and Fixing 'LUXALON' ALUMINIUM CELL CEILING manufactured by M/s. Sqm Hunder Douglas India Pvt Ltd. of approved colour consisting of Main runner, Upper sections, Lower sections all of U- Shaped Profiles 10 mm wide x 50 mm deep x 0.50 mm thick with inwardly returned edges of 2.50 mm. Coil coated on a Continuous paint line, Diuble baked and Roll formed from enamelled corrosion resistance Aluminium alloy ( Al. Mg alloy) for higher strength andRoll forming characteristics.The main runner shall be fixed at a distance of 1.20 metres centre to centre and shall be suspended by means of G.I Suspension Rod 4mm diameter and a galvanised suspension spring clip at a distance of 1.20 metres centre to centre. The cross - Runner shall be fixed to the Main Runner at a distance 0.60 mts c/c. with a self locking device. The Upper Section and Lower section shall be fixed to main runner and cross Runner in form of a Cell Structure of module 100 mm X 100 mm with self Locking device. Grid system for fixing ceiling tiles shall comprise of TEEs. The 24mm main Tee runers shall be suspended at an interval of 1200mm centre to centre. The 24 mm cross tee runner shall be suspended at an interval of 600mm centre to centre and further supported with 24mm cross Tee with interlocking arrangements to form a Grid of 600mm x 600m. The main TEE shall be supported by means of 4mm G.I.Rod from slab / Roof. The suspension shall be provided at 1200 to 1500mm centre to centre.provision for Lights, Diffusers Etc to be made including extra supports wherever necessary. A Non - Woven felt made of glass reinforced fibre glued oner the Perforation for Sound absorbtion Measurements shall be as per actual area of False ceiling with out deductions for lights and diffusers. Measurements shall be area covered by the Cell False ceiling .

Providing and fixing in position SUSPENDED SEAMLESS FALSE CEILING SYSTEM USING 12.50mm THICK MOISTURE RESISTANT PLAIN GYPSUM BOARD seamless false ceiling system using 12.50 mm thick moisture resistant plain gypsum board (GYPROC.MR of M/s .Saint Gobain make) suspended ceiling, which includes Gypsteel ULTRA™ CRP surface ribbed perimeter channels (having one flange of 20mm and another flange of 30mm and a web of 27mm) along the perimeter of ceiling, screw fixed to brick wall/partition with the help of nylon sleeves and screws, at 610mm centres. Then suspending Gypsteel ULTRA™ CRP surface ribbed intermediate channels of size 45mm (with two flanges of 15mm each) from the soffit at 1220mm centres with Gypsteel ULTRA™ CRP surface ribbed ceiling angle of width 25mmx10mm fixed to soffit with GI cleat and steel expansion fasteners (Mfg by Ms Saint Gobain Gyproc).Gypsteel ULTRA™ CRP surface ribbed Ceiling section of having web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the Gypsteel ULTRA™ intermediate channel with the help of connecting clip and in direction perpendicular to the Gypsteel intermediate™ channel at 457.5mm centres. Single layer of 12.5mm tapered edge Gyproc® MR (conforming to BS 1230 part 1) is then screw fixed to ceiling section with 25mm drywall screws at 230mm centres. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Gyproc jointing compound, Gyproc joint paper tape and two coats of drywall top coat (as per recommended practices of M/s Saint- Gobain Gyproc India).

REMOVING FLAT BACK URINALS / EWC / OWC / AIWC carefully along with the cast iron / ceramic / plastic flushing cistern including all its accesseries, items including removing bracket screws & existing C.P. fittings & stacking the same as directed by Engineer-in-charge.

REMOVING HAND WASH BASIN carefully alongwith bottle trap, stop cock, pillar tap, brackets & PVC connections carefully & stacking the the same as directed in Civil Maintenance Stores at BARC Hospital as directed by Engineer-in-charge.

DISMANTLING FLUSHING CISTERN of any size including all its accesseries, removing bracket screws including stacking of useful materials near the site and disposal of unserviceable materials within 100m lead as directed by Engineer-in-charge.

DISMANTLING C.I. PIPES INCLUDING ITS ACCESSORIES IN SHAFTS / OPEN PIPING for following Dia including taking out the pipes manually, breaking lead caulked joints, melting of lead, making into blocks including stacking of pipes within a lead of 200m as per direction of Engineer-in-Charge.

75mm dia CI pipe

100mm dia CI pipe

DISMANTLING G.I. PIPES OF ALL DIAMETER EXTERNAL WORK including excavation and refilling trenches after taking out pipes manually/ by mechanical means including stacking of pipes within 100m lead as per direction of Engineer-in-charge. Note: measurement shall be considered as centre line measurements of pipes of all dia. including fittings & fixtutes & no extra payment shall be made for the attached fittings & fixtures.

REPAIRING OF BIBS TAP / PILLAR TAP / STOP COCK etc. by changing with the spindle, new washers etc. as per site requirement & directed by Engineer-In-Charge.

Providing and fixing Heavy quality FLEXIBLE PVC WASTE PIPE of following dia. (semi rigid or flexible) of approved make for sink or wash basin including PVC waste fittings etc. complete all as per specifications and as directed by the Engineer-in-charge. 32 mm dia flexible PVC (semi-rigid) waste pipe.

Providing and fixing required type FLUSH HANDLES for slimeline or champion make Flushing Cistern.

Providing and fixing WASHERS of Flushing Cistern of OWC / EWC / URINAL etc.

Providing and fixing required type SYPHON SET for slimeline or champion make Flushing Cistern.

Providing and fixing CP BRASS / COPPER INLET CONNECTION pipes heavy quality suitable for hot and cold including CP brass unions and nuts 15 mm dia 600 mm long.

Providing & only supplying of CP BRASS / COPPER INLET CONNECTION pipes heavy quality suitable for hot and cold including CP brass unions and nuts 15 mm dia 600 mm long and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing 15mm PVC INLET CONNECTION SUITABLE FOR HOT AND COLD WATER 600 mm long with nuts and washers complete for wash basins/ Urinals etc. with all necessary acessories complete as directed by the Engineer-in-charge.

Providing & only supplying of 15mm PVC INLET CONNECTION SUITABLE FOR HOT AND COLD WATER 300 mm long with nuts and washers complete for wash basins/ Urinals etc. and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing heavy quality STAINLESS STEEL / C.P. BRASS GRATING of approved equvalent make as specified for floor traps / nahani traps all as directed by the Engineer-in-charge. SS grating 125 mm dia

Providing & only supplying of STAINLESS STEEL / C.P. BRASS GRATING of approved equvalent make as specified for floor traps / nahani traps and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing 150 X150mm SOAP DISH of white viterious Chinaware, of approved make including chasing walls making good the same after fixing the China Soap dish etc. complete all as per specifications and as directed by the Engineer-in-charge.

Providing & only supplying of 150 X150mm SOAP DISH of white viterious Chinaware and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing C.P. BRASS TOWEL RAIL of Jaquar make 600 mm long complete fixed to walls with 30 mm CP brass screws with concealed fitting arrangement all as directed by the Engineer-in-charge.

Providing & only supplying of C.P. BRASS TOWEL RAIL of Jaquar make 600 mm long and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and Fixing CP brass 100mm DIA SHOWER ROSE WITH SHOWER ARM of Essco / Jaquar make as per specifications and as directed by Engineer-in-charge complete.

Providing & only supplying of CP brass 100mm DIA SHOWER ROSE WITH SHOWER ARM of Essco / Jaquar make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing 15 mm n.b. C.P. BRASS OPEN STOP COCK of Heavy Quality of specified / approved make as per specifications and as directed by the Engineer-in-charge

Providing & only supplying of 15 mm n.b C.P. BRASS OPEN STOP COCK of jaquar make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing 15 mm dia C.P. BRASS BIB COCK of heavy quality of specified / approved make as per specifications and as directed by the Engineer-in-charge

Providing & only supplying of C.P. BRASS BIB COCK of jaquar make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing 15mm C.P. BRASS 2 IN 1 BIB COCK AND ANGLE COCK combination of Heavy Quality of approved make as per specifications and as directed by the Engineer-in-charge

Providing & only supplying of 15mm C.P. BRASS 2 IN 1 BIB COCK AND ANGLE COCK of jaquar make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing EURONICS LIQUID SOAP DISPENSER ES-05 etc. complete in all respect as per specifications and as directed by the Engineer-in-charge.

Providing and fixing 15mm C.P. BRASS JAQUAR SWAN NECK PILLAR COCK of heavy Quality of approved make and specied type as per specifications and as directed by the Engineer-in-charge.

Providing and fixing Heavy Quality 15mm C.P. BRASS PILLAR COCK ELBOW OPERATED of approved make as per specifications and as directed by the Engineer-in-charge.

Providing, Supplying & Fixing of FOOT OPERATED PILLAR TAP OR VALVE with Brass Spout including a pair of 3 feet PVC connections and cost of all accessories etc. complete as directed by the Engineer-in-Charge.

Providing and fixing Heavy Quality 15mm C.P. BRASS 3 WAY MULTI-OUTLET LABORATORY PILLAR COCK of Onida make / approved equivalent as per specifications and as directed by the Engineer-in-charge.

Providing and fixing heavy quality HEALTH FAUCET with 1.50 metres long flexible hose (Hand Shower / Hand Spray) of approved make with wall brackets and type as per specifications and as directed by the Engineer-in-charge

Providing & only supplying of HEALTH FAUCET with 1.50 metres long flexible hose of Jaquar make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing stainless steel TOILET PAPER HOLDER recessed type of Jaquar make / approved equivalent and type with S.S screws as directed by the Engineer-in-charge complete.

Providing & only supplying of TOILET PAPER HOLDER of recessed type of Jaquar make / approved equivalent and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing heavy quality CP BRASS BOTTLE TRAP 31 / 32 mm of approved make single piece moulded with height of 270mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal,of approved make for wash basins / urinal etc all as per specifications and directed by the Engineer in charge.

Providing & only supplying of heavy quality CP BRASS BOTTLE TRAP 31 / 32 mm of approved make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing heavy quality C.P. BRASS WASTE COUPLING of following dia for wash basin and sink, of approved make, size and quality all as directed complete C.P Brass Waste coupling 32 mm Dia of approved make Half threaded or Full threaded as per requirement.

Providing & only supplying of C.P. BRASS WASTE COUPLING of approved make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing BRASS BALL COCK (TECHNO make) or approved Equivalent heavy quality of following sizes with arm rod and Plastic Ball floats complete as per specifications and as directed by the Project Engineer

20 mm dia.

25 mm dia

50 mm dia

Providing and fixing white VITREOUS CHINA LABORATORY SINK of size 530 x 430 x 180 mm with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass trap with C.P. brass unions complete including painting the fittings and brackets with 3 coats of white enamel paint over a coat of primer, cutting and making good the walls wherever required complete as per specifications and as directed by the Engineer-in-Charge.

Providing & only supplying of white VITREOUS CHINA LABORATORY SINK of size 530 x 430 x 180 mm of approved make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing VITERIOUS CHINA WASH BASIN of approved make and colour with C.I. brackets, 15mm C.P. brass pillar tap of approved make,15 mm x 600mm long PVC Inlet connection, 32 mm heavy quality C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls and testing complete all as per specifications and as directed by the Engineer-in-charge. White vitreous China wash basin size 630 x4 450 mm and equivalent sizes with single 15mm C.P. brass pillar tap

Providing & only supplying of VITERIOUS CHINA WASH BASIN of approved make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing satin finish STAINLESS STEEL AISI 304 (18/8) KITCHEN SINK of size 610 x 510 mm without drain board and bowl size 685 x 535 x 250 mm depth as per IS13983 of approved make, with C.I. brackets, fittings and stainless steel plug 40 mm including painting the fittings and brackets with 3 coats of white enamel paint over a coat of primer, cutting and making good the walls wherever requried complete as per specifications and as directed by the Engineer-in-charge.

Providing & only supplying of STAINLESS STEEL AISI 304 (18/8) KITCHEN SINK of approved make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing INDIAN WATER CLOSET (ORISSA PAN) of apperoved make with 100 mm China ware P or S trap, One no. 10 litre High level or low level white PVC flushing cistern with flush pipe & bend with manually controlled device (handle lever) conforming to IS:7231, PVC 15 mm Inlet connection with all fittings and fixtures complete including all connection, embedding in position commissioning, cleaning etc. all as per drawings and specifications and as directed by the Engineer-in-charge. White Vitreous china Orissa pattern W.C. pan of size 580x440 mm

Providing & only supplying of INDIAN WATER CLOSET (ORISSA PAN) of approved make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing white VITREOUS CHINA EUROPEAN TYPE WATER CLOSET with 'P' or 'S' Trap with solid seat and lid of approved make, 10 litre low level white PVC flushing cistern with manually controlled device (handle lever) conforming to IS:7231, flush bend, fixing EWC with C.P brass screws, 15 mm PVC heavy quality inlet connection of 450 mm long, including testing , commissioning & cleaning etc. complete all as per drawings and specifications and as directed by the Engineer-in-charge E.W.C. pan in White colour with ISI marked white solid plastic seat and lid.

Providing & only supplying of VITREOUS CHINA EUROPEAN TYPE WATER CLOSET of approved make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing & only supplying of HINDWARE WALL MOUNTED EWC-WHITE-DOVE MODEL with seat cover of approved make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing white VITREOUS CHINA FLAT BACK HALF STALL URINAL size 580 x 380 x 350 mm / 610 mm Hindware or Equivalent approved make with 15 mm C.P. Brass Presstomatic Series Auto Shut Urinal Flush Cock of "Jaquar" make, with CP Brass flush pipe unions, Heavy Quality C.P. brass Spreaders, C.P waste coupling with dome grating, clamps complete all as per specifications drawings and as directed at site.

Providing & only supplying of VITREOUS CHINA FLAT BACK HALF STALL URINAL size 580 x 380 x 350 mm / 610 mm of approved make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing CHINAWARE HALF ROUND URINAL CHANNEL 100 / 150 mm dia with or without dead ends set in C.M 1:3 laid to proper slope & grade including finsihing the joints with polymer based tile grout mix as per drawing and as directed by the Engineer-in-charge

Providing and fixing Brass 15 mm C.P. BRASS PRESSTOMATIC SERIES AUTO SHUT URINAL FLUSH COCK of "Jaquar" make or equivalent approved quality.

Providing & only supplying of 15 mm C.P. BRASS PRESSTOMATIC SERIES AUTO SHUT URINAL FLUSH COCK of "Jaquar" make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing 15mm C.P. BRASS URINAL SPREADER size with 1/2" BSP thread and shapes, weighing not less than 60 gm of approved make and type.

Providing & only supplying of 15mm C.P. BRASS URINAL SPREADER of approved make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing PVC LOW LEVEL / HIGH LEVEL FLUSHING CISTERN 10 litre capacity of approved make in white colour with flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures etc. complete as per specifications and as directed by the Engineer-in-charge.

Providing & only supplying of PVC LOW LEVEL / HIGH LEVEL FLUSHING CISTERN 10 litre capacity of approved make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge

Providing and fixing cast iron NAHANI TRAP / FLOOR TRAP of 100 mm inlet and 75 mm outlet, (weighing 5.80 Kg each), jointing with lead with the connection pipes, placing as per the drawings, embedding in cement concrete 1:2:4 and making circular hole up to floor level using 110 mm O/D PVC pipes of 6 Kg / sq.cm pressure and fixing 1 No 125 mm dia C. P brass grating, complete all as specifications and drawings and as directed by the Engineer-in-charge.

Providing & only supplying of NAHANI TRAP / FLOOR TRAP of 100 mm inlet and 75 mm outlet of approved make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing and fixing 6mm THICK MIRRORS of size 600mm X 450mm of approved make with bevelled edges complete with 6 mm thick asbestos sheet back ground fixed to walls with C.P. brass screws and concealed washers complete. all as per specifications and as directed by the Engineer-in-charge..

Providing & only supplying of 6mm THICK MIRRORS of size 600mm X 450mm of approved make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Extra for providing and fixing approved make STAINLESS STEEL 304 GRADE STUDS (with wall spacers) for mirrors etc. complete all as per specifications and as directed by the Enginner-in-charg

Providing & only supplying of STAINLESS STEEL 304 GRADE STUDS of approved make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge

Providing and fixing SOLID PLASTIC SEAT of approved colour suitable to existing EWC with lid including CP brass / SS bolts, screws etc. for pedestal type W.C. pan complete as per specifications and as directed by the Engineer-in-charge

Providing & only supplying of SOLID PLASTIC SEAT of approved make and fixing with the Item No 225.1 / 225.2 / 225.3 / 225.4 as applicable as approved by Engineer-in-Charge.

Providing, Laying, jointing, fixing and testing Heavy quality (C-Class) GALVANISED IRON PIPES and ISI marked fittings like, tees, elbows, bends, unions, nipples,reducers etc. as required for the work, including testing the pipes and fittings for 10.00 Kg / Sq.Cm hydralic pressure with a minimum period of two hours duration with clean water, including cutting , threading, jointing with hemp yarn, white lead, jointing Teflon tape, exposed / concealed by chasing walls and making good by filling with concrete 1:3:6, complete all as per specifications and drawings, including two coats of anti corrosive bitumastic paint for all concealed lines / two coats of synthetic enamel paint for all exposed lines all as directed by the Engineer-in-charge. Pipes with exclusive use of TATA make C-Class pipes.

15 mm n.b. G.I pipe Exclusive TATA Make

20 mm n.b. G.I pipe Exclusive TATA Make

25 mm n.b. G.I pipe Exclusive TATA Make

32 mm n.b. G.I pipe Exclusive TATA Make

40 mm n.b. G.I pipe Exclusive TATA Make

50 mm n.b. G.I pipe Exclusive TATA Make

Providing and fixing CHLORINATED PVC (CPVC) PIPES having thermal stability for hot & cold water supply (as ASTM Standard 2846 & SDR - 11 Grade) including all CPVC Plain & Brass threaded fittings, fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with CPVC Solvent cement & testing the joints complete all as per specifications, drawings and as directed by the Engineer-in-Charge..

15 mm outer dia CPVC pipe (External) / open

20 mm outer dia CPVC pipe (External) / open

25 mm outer dia CPVC pipe (External) / open

32 mm outer dia CPVC pipe (External) / open

40 mm outer dia CPVC pipe (External) / open

50 mm outer dia CPVC pipe (External) / open

Providing & fixing in position heavy pattern screw down GUN METAL GATE VALVE with handles and wheels of approved make including testing for 10Kg/cm2 pressure with clean and potable water with a minimum testing duration of two hours etc.as per specification and as directed by the Engineer-in-Charge.

Providing, supplying, fixing in position, under floors or in walls CENTRIFUGALLY CAST IRON PIPES including required specials like bends, tees, 'Y' collars, cowl etc for soil, waste and ventilation pipes conforming to IS.3989 of approved make including cost of jointing with spun yarn and molten lead of specified quantity, caulking the joints, including testing of pipes, painting with primer, fixing at walls with necessary approved type of clamps and brackets complete all as per drawings and specifications and as directed at site..

75 mm dia centrifugally cast (spun) iron socketed pipe as per IS:3989 using 0.90 kg lead / joint

100 mm dia centrifugally cast (spun) iron socketed pipe as per IS:3989 using 1.00 kg lead / joint

150 mm dia centrifugally cast (spun) iron socketed pipe as per IS:3989 using 1.20 kg lead / joint

Only supplying CENTRIFUGALLY CAST IRON PIPES for soil, waste and ventilation pipes conforming to IS.3989 of approved make including approved type of clamps and brackets as directed by Engineer-in-Charge.

75 mm dia centrifugally cast (spun) iron socketed pipe as per IS:3989 using 0.90 kg lead / joint

100 mm dia centrifugally cast (spun) iron socketed pipe as per IS:3989 using 1.00 kg lead / joint

150 mm dia centrifugally cast (spun) iron socketed pipe as per IS:3989 using 1.20 kg lead / joint

Providing and fixing UNPLASTISIZED CHLORINATED PVC (UPVC) PIPES having thermal stability for hot & cold water supply (as ASTM Standard 2846 & SDR - 11 Grade) including all UPVC Plain & Brass threaded fittings, fixing the pipe with clamps at 1.00 m spacing / under ground. This includes jointing of pipes & fittings with UPVC Solvent cement & testing the joints complete all as per specifications, drawings and as directed by Engineer-in-charge.

63 mm outer dia UPVC pipe In Trenches / open

75 mm outer dia UPVC pipe In Trenches / open

90 mm outer dia UPVC pipe In Trenches / open

110 mm outer dia UPVC pipe In Trenches / open

160 mm outer dia UPVC pipe In Trenches / open

Providing and fixing PVC RAIN WATER PIPES conforming to relevant IS type B and PVC SWR fittings & specials conforming to relevant IS including jointing with seal ring / With PVC solvent adhesive including fixing in walls using clamps etc complete all as per drawings, specifications and as directed by the Engineer-in-charge.

SWR PIPE 90 mm O/D.

SWR PIPE 110 mm O/D

SWR PIPE 160 mm O/D .

Only supplying PVC RAIN WATER PIPES conforming to relevant IS Type B and PVC SWR fittings & specials, clamps etc. as directed by the Engineer-in-charge..

SWR PIPE 90 mm O/D

SWR PIPE 110 mm O/D

SWR PIPE 160 mm O/D

Supplying and fixing CAST IRON MAN HOLE COVERS and CAST IRON STEPS of approved make and weight as specified in the drawings or as directed by the Engineer in charge.

Providing WHITE WASHING with ready mix lime powder of approved make to give an even shade (Three coats), including scaffolding as per specifications and as directed by the Engineer-incharge

Providing POLISHING ON WOOD WORK with ready made wax polish of approved brand and manufacturer all as per specifications to required finish and as directed by the Engineer -in-charge complete.

Providing and applying ONE COAT OF CEMENT PRIMER of approved brand on wall surface to receive specified paint including scaffolding complete all as per specifications and as directed by Engineer-in-charge

Providing, applying wall painting two coats on old work with premium PLASTIC EMULSION PAINT of approved brand to give an even shade without cement primer including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing and Painting two coats of SYNTHETIC ENAMEL PAINT on steel surfaces of approved brand and manufacture to give an even shade with primer coat including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing and treating the OLD surface with ANTI FUNGAL TREATMENT using of M/s Artilin/Artibose or Approved Equivalent DÉCOR HYGIENE+ of M/s Nanova Care. i) The old paint to be scrapped out ii) The neeru/cement punning to be removed by chipping wherever required iii) Entire surface to be finished with white cement based wall putty of approved make to get uniform surface free from undulations iv) One coat of cement primer to be applied v) Two coat of M/s Artilin/Artibose or Approved Equivalent Antifungal Treatment to be applied vi) One coat of cement primer to be applied complete etc. complete as directed by the Engineer-in-charge.

Providing, painting and finishing Antifungual Treated Surface with ANTIFUNGAL PAINT of M/s Artilin/Artibose or Approved Equivalent Paints DÉCOR HYGIENE+ of M/s Nanova Care with two coats over treated surface all as per manufacturer's specifications and as directed by the Engineer-in-charge.

CLEANING OF UNDERGROUND & OVERHEAD WATER TANK by high pressure cleaning system with hydrodynamic mechanism with nozzels, slurry pumps at 180 bar pressure with required quantity of water and subsequently disinfecting the tanks with food quality chemical / ultraviolet treatment etc. complete through M/s Tanclean or equivalent approved and as directed by EIC

TESTING OF WATER SAMPLE periodically after cleaning the tanks for “Potable Water Quality & Bacteriological Contamination (IS:10500)” as directed by the EIC.

Chemical Test Parameters

Bacteriological Test Parameters

Opening of nahani trap, removing nahani trap jalli, CLEANING THE COMPLETE NAHANI TRAP / FLOOR TRAP and refixing the same with white cement etc. as directed by Engineer in charge.

Opening of bottle trap from its joint, CLEANING THE COMPLETE BOTTLE TRAP and refitting/refixing same to the sinks, wash basins etc. as directed by Engineer in charge (Note:- If bottle trap is found in unused condition it will be supplied by department at free of cost)..

CLEANING AND REMOVAL OF CHOCKING OF SEWAGE WASTES, MUCK, FROZEN SEWAGE CAKES ETC. FROM EWC/IWC/AIWC MANUALLY, including cost of labour tools, trooly of sewage muck for disposal of designated place, all complete in all respect and as directed by Engineer in charge.

CLEANING THOROUGHLY THE EXISTING SERVICE SHAFTS (ALL FLOORS IN VERTICAL) / BEHIND RCC JALI / GENTS & LADIES TOILET at all floors including cleaning throughly the existing cast iron soil and rain water pipes of all wastes, removing rags, loose material, cob webs, cloth pieces , broken concrete pieces and all deleterios materials including lift and lead charges, cost of all tools, tackles, plants, accessories etc. all complete and as directed by Engineer in charge.

CLEANING OF SEWAGE PIPE LINE: Cleaning and removal of sewage or drainage wastes, muck etc. from horizontal, sloping RCC/CI/PVC lines of all dia. (burried undergroung/under roads/exposed) connecting to sewage inspection chambers, manhole chamber etc. by mechanically / manually as desired by EIC including cost of labour, tools, machines, transportation etc.

LABOUR CHARGES ONLY FOR THOROUGHLY CLEANING AND REMOVING DUST PARTICLES, OILING THE HINGED PORTION / PARTS FOR SERVICEABLE CONDITION OF ALUMINUM / M.S / WOODEN DOORS, WINDOWS, COLLAPSIBLE GATES, M.S HEAVY GATES including cleaning of glaas panels, removing the existing dust from trackc by blower, cleaning the fittings & fixtures before greasing, applying approved greese, oil etc. complete all as directed by Enginee-in-Charge. Note: Quantity of work considered for 1 Operation comprises of entire hospital building including the following: a) Aluminum glazed doors with floor spring or without floor spring ≈ 125 nos. b) Aluminum glazed sliding windows or side hung windows ≈ 2500 Nos. c) Aluminum glazed window panels of fixed / luared / hinged type ≈ 2500 Nos. d) Collapssible grill gate ≈ 20 Nos. e) Alluminium hollow metal gate / M.S. heavy gate ≈ 20 Nos. f) M.S. or Wooden door shutters & frames ≈ 150 Nos. g) M.S. or Wooden window shutters & frames ≈ 2500 Nos.

REMOVING AND RELAYING 60mm THICK CEMENT CONCRETE INTERLOCKING PAVER BLOCK with 50 mm thick compacted bed of crushed sand, filling the joints with crushed sand etc. all complete as -per the direction of the Engineer-in-charge

PROVIDING AND LAYING 60mm THICK FACTORY MADE CEMENT CONCRETE INTERLOCKING PAVER BLOCK OF M-30 grade made with strong vibratory compaction and approved size, shape, design laid in required colour and pattern over and including 50 mm thick compacted bed of crushed sand, filling the joints with crushed sand etc. Including removing old paver blocks, disposing the same outside the colony. all complete as -per the direction of the Engineer-in-charge

Providng and fixing at or near ground level PRECAST CEMENT CONCRETE 1:2:4 IN KERBS, Using 100% manufactured sand, edgings etc. as per approved patterns and setting in position with C.M 1:3 (using coarse sand) including consolidation, curing, cost of required centering, shuttering, finishing smooth with 6 mm thick cement plaster 1:3 (using fine sand) on exposed surfaces complete as per specifications.

Providing and fixing PRECOATED GALVALUME ROOFING PROFILE SHEETS (0.50mm Thickness in Single Sheet) of approved size, shape and pitch up to and including single length of 12.00 met. The sheet shall be fixed using self drilling / self tapping screws of size (5.5 X 55 mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers filled with white lead complete upto any pitch in horizontal / vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required as directed by the Engineer-in-charge.

Providing and fixing ROOFING ACCESSORIES OF GALVALUME SHEET up to 600 mm total width for ridges, gutters, aprons,and flashings for precoated Galvalume Roofing using self drilling / self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete.e.

Providing, supplying, cutting, welding, fabricating, hoisting and fixing in position STRUCTURAL STEEL MEMBERS LIKE TRUSSES, PURLINS POSTS etc. using MS hollow / circular / square / rectangular tubular sections including appling a coat of Zinc chromate primer of approved make all as per specifications, drawings and as directed by the Engineer in charg.

Providing and Fixing SENSOMATIC BASIN MOUNTED PILLAR COCK (Model No. ET-01-BE) with Electric Operated / AC Battery Operated infrared sensor of "M/s Euronics or equivalent approved" having water inlet from bottom side, including fixing to wall with suitable brackets, accessories etc. all as per manufacturers specifications and direction of Engineer-in-charge

Providing and Fixing SENSOMATIC URINAL FLUSHER TO EXISTING URINALS (Model No. EU-02-P) with Electric Operated / AC Battery Operated infrared sensor of "M/s Euronics or equivalent approved" having water inlet from back side, including fixing to wall with suitable brackets, accessories etc. all as per manufacturers specifications and direction of Engineer-in-charge.

REPAIRING OF SENSOMATIC PILLAR COCK and URINAL FLUSHER etc. by changing with Set of 4Nos. 1.5V AA DURACELL battery / solinoid valve / sensor / baterry holder / casin box etc. as required as per site requirement & directed by Engineer-In-Charge.

Replacement of One set 4Nos. 1.5V AA DURACELL battery

Replacement of Sensor for EU-02-P

Replacement of Solenoid Valve for EU-02-P

Replacement of Battery Box for EU-02-P

Replacement of Sensor for ET-01-BE

Replacement of Clamp Set for ET-01-BE

Replacement of Spring Washer for ET-01-BE

Replacement of Electrical Adopter for ET-01-BE

Replacement of Control Box for ET-01-BE

Providing and fixing "1600 WALLGUARD" to walls at suitable height from finished floor level comprising of continous aluminium retainer of 2mm thick with mill finish, adjustable rail mounting base with impact absorbing strip, end caps and high impact poly viny lchloride, the surface cover of size 152mm X 25mm etc. complete including manufacturers specifications, labours, too|s, tackles and installation as per manufacturer specifications and as directed by E|C. The approved make for wallguards is M/s Inprocorp India Pvt. Ltd. or equivalent approved. Thecomplete assembly shall able to withstand abrasion, weather resistance, ClassA fire rating, impact strenfkh of 30.4 Ft-lbs/inch, chemical & stain resistance, antibacterial & antifungal and textured to provide anti slip surface. The fittings and anchorages can withstand corrosion exposed to normal envionmental conditions.The complete assembly shallbe guarantted against cracking and abrasion for a period of one year from date of installation

Providing and fixing "160 HIGH IMPACT CORNER GUARD" to walls at sutable height from finished floor level comprising of continous aluminium retainer of 1.80mm thick with mill finish, adjustable rail mounting base with impact absorbing strip, top caps and high impact poly vinyl chloride, the surface cover of size 51mm X 51 mm (90 degree) etc. complete including manufacturers specifications, labours, tooIs, tackles and installation as per manufacture specifications and as directed by EIC. The approved make for wallguards is M/s Inprocorp India Pvt. Ltd. or equivalent approved. The complete assembly shall able to withstand abrasion, weatherresistance, Class A fire rating, impact strenfth of 30.4 Ft-lbs/inch, chemical & stain resistance, antibacterial & antifungal and textured to provide anti slip surface. The fittings and anchorages can withstand corrosion exposed to normal envionmental conditions. The complete assembly shall be guarantted against cracking and abrasion for a period of one year from date of installation.

Providing, laying, FIXING WITH WELD-JOINTING AND TESTING HEAVY QUALITY (ISI MARKED C-CLASS) GALVANISED IRON PIPES AND ISI MARKED FITTINGS like, tees, elbows, bends, unions, nipples, reducers etc. as required for the work, including testing the pipes and fittings for 10.00 Kg/Sq.Cm hydralic pressure with a minimum period of two hours duration with clean water, including cutting, threading, jointing with hemp yarn, white lead, jointing teflon tape, chasing walls and making good by filling with concrete 1:3:6, complete all as per specifications and drawings, including two coats of anti corrosive bitumastic paint, all as directed by the Engineer-in-charge. Pipes with ISI marked 'C'-Class heavy quality pipes of approved make

(a) 80 mm n.b.

(b) 100 mm n.b.

Fabricating and jointing pipes / plates / frames etc. by BUTT WELD for pipe to pipe, pipe to plate or any kind of jointing of MS works.

Providing and fixing 304 GRADE STAINLESS STEEL WORK for Open drain/ Drain grating / Nhani trap/Jali/hand rail in pipe section/ of approved size and make and quality by welding, mirror / matt polishing , fixing at site etc. for kitchen floor drain/balcony railing & staircases railing including special sections as per drawings, specifications. complete. A sample to be fabricated and to be got approved by the Architect/ Project Engineer before starting of work at site . This work to be executed through approved specialized agency.

Providing and fixing 304 GRADE STAINLESS STEEL ROOM NO PLATE of size 100mm x 40mm of matt polishing, grooving the Room No and Border on Plate as approved by Engineer-in-Charge and fixing with SS Screw at site etc. This work to be executed through approved specialized agency.

Providing and fixing glazing in aluminium doors, window, ventilator shutters and partitions etc. with TOUGHENED FLOAT GLASS PANES with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-charge (Cost of snap beading shall be paid in basic item)

With toughened float glass panes of 6.00mm thickness

With toughened float glass panes of 12.00mm thickness

Providing and Supplying 25mm thick SOLID PVC INTEGRAL SHEET Made out of J1054 Integral Foam Sheet of M/s Jain Irrigation System Ltd. of white colour or as directed by Engineer-in-Charge.

Providing and Supplying PVC Loovers suitable for fixing in Solid PVC Integral Sheet Doors of white colour of approved brand as directed by Engineer-in-Charge.

Carrying out Civil Engineering Works like SURVEYING, LEVELLING, CHECKING OF FORMWORK, FABRICATION, REINFORCEMENT, WITNESSING SAMPLE RETRIEVAL & TESTING, PREPARATION OF RA BILLS, ENSURING CONCRETE INGREDIENT RATIO IN RCC / PCC WORKS, BRICKWORK, PLASTER, FLOORING AND OTHER CIVIL WORKS AT SITE including preparation of tender documents, draft work order, agreements, compiling, binding, labeling and keeping data in computer as per direction of Engineer-in-Charge. Note: 1) Each Job shall be carried out by one qualified Diploma holder / Licentiate in Civil / Construction Engineering / Technology conducted by board of Technical Examinations / University / Autonomous Govt. / Govt. recognized Polytechnic / Institute with minimum 2 years experience. 2) Deployment: The contractor shall deploy one engineer per month for a job for 6 working days per week for minimum 08:30 hours per day with 30 minutes of break. 3) Mode of measurement: Measurement will be as per job basis and part thereof. Deployment of one engineer per month will be measured as one job.

CARRYING OUT MANUAL MISC. CARPENTRY / PLUMBING / CIVIL / MASONRY JOBS like minor repairs, fixing fitting and fixtures etc. as and when required and as directed by the Engineer-in-charge Note: 1. Labours shall bring necessary carpentary / plumbing tools, minimum materials such as washher, taflon tape, rawlpludge, screws, clips etc. 2) Payment shall be made as per the Log book duly approved by the Enginner in charge. 3) Contrator shall arrange necessary Police Verification Certificate for the workers engaged for thess work.

SKILLED CARPENTERY JOB / WORKS with valid Police Verification Certificate for entire contract perio

SKILLED PLUMBING JOB / WORKS with valid Police Verification Certificate for entire contract period.

SKILLED CIVIL or MASONRY JOB / WORKS with valid Police Verification Certificate for entire contract period

SKILLED CIVIL or PAINTING JOB / WORKS with valid Police Verification Certificate for entire contract period.

SEMI-SKILLED CARPENTRY/PLUMBING/MASONRY JOB / WORKS with valid Police Verification Certificate for entire contract period.

Meena Enterprises