SPECIAL REPAIR TO BLDG No. EM-97 OF AD GP (SP), SPECIAL REPAIR TO BLDG No. 1-2C(MED STORE) OF MH NASIRABAD PROVN OF SOAKAGE WELL NEAR BY BLDG No. 234 AND PROVN OF SENTRY POST AT MT PARK OF AD REGT (SP) AT NASIRABAD CANTT UNDER GE NASIRABAD

Amount

Taking down cement or cement lime plaster on stone/brick wall, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Raking out joints/ pointing to random rubble or polygonal rubble uncoursed or brought up to courses built in cement mortar, complete all as specfied and directed.

M&L for rendering in cement mortar (1:6), 15mm thick on other than fair faces of stone masonary surfaces finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:4) mixed with water proofing compound @3% by weight of cement or as per manufacturer's instruction on fair faces of brick work or concrete surfaces, finished even and smooth complete all as specified and directed (WPC shall be measured and paid separately) .

M&L for rough cast plaster over 10mm thick cement plaster in cement mortar 1:4 on stone / brick masonary wall surfaces complete all as specified and directed.

M & L for preparation of new decorated surfaces of walls and providing two coat of cement base paint over a coat of primer, complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper over 1 mm thick wall care putty complete all as specified and directed

M&L for preparation of new plastered surfaces and applying two coats of weather proof acrylic emuslion paint over a coat of 1mm thick wall care putty & including a coat of emulsion wall primer all as per manufacture's instructions & as directed by Engr -in-Charge.

M&L for preparation of old concrete surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Demolition of cement concrete (unreinforeced) in floors and paving n.exc 15cm thickness (above or below ground level) complete all as specified and directed.

M&L for machine cut Kota stone slab flooring of size not less than 550X550mmX18-20mm thick over 15mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed 10mm thick in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing & polishing complete all as specified & directed.

M&L for 8 mm thick non skid ceramic coloured tiles (Square/ rectangular) polished, area of each tiles exc 0.18 sqm but not not exceeding 0.38 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6) complete all as specified and directed.

All as per description of serial item No. 13 above but on vertical surfaces of wall such as dados, skirting etc set and jointed in neat slurry and pointed in white or colour cement to match over and including 10mm thick screed plaster in CM 1:4 complete, all as specifed and directed

M&L for 25 mm thick PCC (1:2:4) type B-0 using 12.50 mm graded stone aggregate, complete, all as specified & directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

Dismantling of ceiling board/lathing any thickness including frame work complete all as specified and directed.

Providing & Fixing false ceiling with Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights as per direction of Engineer-in-charge.

Dismantling asbestos Cement (corrugated, semi corrugated, etc) sheets in roof covering complete all as specified & directed.

S & F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ Lor J type hook complete all as specified & directed.

S & F for pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ Lor J type hook complete all as specified & directed.

S & F second class HW 35mm thick, factory made, plain framed, paneled shutter (Three panels) with panels of 9mm thick BWP grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to IS-710. The size of rails & style shall be as per IS-1003 (part-I) kiln seasoned & chemically pressure treated complete all as per specified and directed.

S&F 2nd class HW 35 mm thick, gauged and skeleton shutters (Three Panels), factory made open rebated and prepare to receive glass, gauge etc (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. Size of members of shutter shall be as specified in SSR 2009 Part-I, section 8 clause Member shall be kiln seasoned & chemically pressure treated complete all as specified and directed.

S & F Steel window factory made, out of MS hollow section 79mm x 39mmx1.6mm thick frame with double shutter (glazed & wiregauged shutters) made out of Z section using flush butt welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements as per sample approval by GE, provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four Nos lugs welded to frame inculding necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 including synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured & paid separately under respective items.

S & F aluminium handle fabricated type, anodised 150mm size conforming to IS complete all as specified and directed.

S & F 300mm long aluminium alloy, anodised, sliding door bolts with hasps, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled, ISI marked of size 100 mm, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site complete and making good disturbed surfaces of wall in CM (1:3), complete, all as specified and directed.

Taking down unserviceable chowkhats or frame with shutters (without taking off shuters from the frames) of any description n. exc 1.50Sqm and removing from site and making good disturbed surfaces of wall in CM 1:3 complete all as specified & directed. (For windows and ventilators)

Taking down shutters of any description exc 1.00 Sqm but n. exc 2.00 sqm each leaf and removing from site, complete all as specified and directed

M & L for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as specified & directed.

S&F mild steel framed work as in doors / gates / steel frames / chowkats etc. of angle or other section with gusset plates, rails, braces, etc., complete conforming to Grade E-165 (Fe 290), drilled for fixing of steel sheeting or other covering including necessary welding etc and fixing in position complete.

S&F in repairs fancy type 20mm dia SS curtain rods fixed to bracket complete all as specified& directed.

S&F decorative type knobs with bracket of Stainless Steel fixing at end of curtain rod complete al as specified & directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with wire staples complete all as specified & directed.

S&F 3 mm thick sheet glass, ordinary / figured quality & glazing with oil putty not exc 0.50 Sqm each pane complete all as specified & directed.

Demolition of stone/brick masonry built in cement or cement lime mortar all as specified and directed.

M&L for brick work with fly ash bricks straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

M&L for fly ash brick work with old size bricks staright or curved on plan to any radius in half brick walls, built in CM 1:4 complete all as specified and directed.

Surface dressing n.exc 15 cm deep and getting out in soft/ loose soil complete all as specified and directed.

M&Lfor machine pressed precast concrete reflective type, coloured, interlocking paver block any shape and size confirmeing to IS-15658-2006 of 60 mm thick, M-35 grade with grey cement and pigment over 50 mm thick sand cushioning, etc complete all as specified and directed.

M&L for PCC 1:2:4 Type B-1 (using 20mm stone crushed agg.) as in rounded or chamfered on edges in any description complete all as specified and directed.

M&L for 100mm thick PCC (1:4:8) type D-2 using 40 graded stone aggregate as in sub base of floor, complete all as specified & directed.

Dismantling of timber scantling 40 sqm and over, in framed work, complete all as specified and directed

S&F steel work in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St -240 complete all as specified and directed.

M&L for PCC 1:2:4 Type B-1 (using 20mm stone crushed agg.) as in fixing of vertical post complete all as specified and directed.

M&L for PCC 1:2:4 Type B-1 (using 20mm stone crushed agg.) as in surface channel & drain etc complete all as specfied and directed

M&L for new plastered surface of wall and applying two coat of plastic emulsion paint over a coat of primer over a coat of (average 1mm thick) wall care putty, complete all as specified and directed.

M&L for 16-18mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window -cills, cooking platforms and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding of edge laid over 15mm thick screed bed in CM (1:6), complete all as spcified and directed.

S&F in repair stainless steel sinks with draining board made of 1mm thick sheet with over all size 915mm x 460mm and bowl size 410mmx330x160mm for kitchen or laboratory with pluge washers and waste, including bedding in cement mortar on to dwarf walls or including fixing centilever bracket and connecting uinon to waste pipe complete all as specified and directed.

M&L for glazed ceramic coloured tiles 7 to 8 mm thick in vertical surfaces area of each tile exc 0.11 Sqm and but not exc. 0.18 Sqm, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick plastering in cement mortar 1:4 complete all as specified and directed.

S & F water tubing 15 mm bore, medium weight, ISI marked galvanized with all fittings and fixed to walls, ceiling or laid in floors complete all as specified and directed.

M&L PVC Nahani/Floor trap 75 mm outlet,with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) complete all as specified

M&L for 18/19mm thick prelaminated particle board exterior grade pelaminated both side with decorative choice fixed complete, including teak wood lipping 19 x 6mm thick fixed with nails in shelves, partition and palmet boxes, shelves, almirah book cases, toilet boxes, racks, cup board shutter and similar works all as spepcified and directed.

S & F continuous (piano) hinges, mild steel, bright finish width of flaps (when open ) 40 mm all as specified and directed.

S & F 75mm size hasp and staple, aluminium anodised safety type, fixed with screws complete all as specified and directed

S & F 50 mm dia polished hardwood knobs fixed with screws complete all as specified and directed.

S&F fancy type 20mm dia aluminium curtain rods powder coated fixed to bracket completed all as specified& directed.

S&F 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F ball valves PTMT high pressure with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe, 20mm bore compete (Minimum weight 210 gm)

S&F gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 20 mm dia, ISI marked complete all as specified& directed.

M&L for 50 mm thick sand stone slabs; set and jointed over joists etc. in CM 1:4 as in base of water tank/ manhole cover and other similar work complete all as specified and directed

M & L for framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-16 complete all as specified and directed.

Dismantling of single layer Mangalore pattern or similar tiles in roofing comlete all as specified and directed.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, necessary welding etc. conforming to Grade E-250 quality `A’ all as specified and as directed.

M&L for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate in foundations, filling and mass concrete.

M&L for walling of random rubble, brought upto courses, well bonded, bedded and solidly hearted stone masonry built in cement mortar 1:6 complete all as specified & as directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses, hammer dressing with maximum depression on face from straight edge held against the dressed surface not exc 20mm, lime or sand stone complete all as specified & as directed.

M&L for 40mm thick PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in damp proof course on horizontal surface using water proofing compound including necessary formwork. Note : - Supply only water proofing compound shall be measured and paid for separately.

Supply only water proofing compound, ISI marked

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.

M&L for 75 mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete.

Formwork to edges of concrete flats, roofs, floors etc and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for rough finished surfaces.

M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

M&L for reinforced cement concrete 1:2:4 (Nominal mix) using 20mm graded crushed stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like.

M&L for rendering 10mm thick in cement mortar 1:4 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

M&L for 75 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

All as per description of serial item no. 81.00 above but on vertical surfaces such sirting/dado etc over & including 10mm thick screed plaster in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L for preparation of newly plastered surfaces of walls & applying three coats of white wash complete all as specified.

BLANK

M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to SGSW drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

M&L for 150 mm bore reinforced concrete pipe, class NP3, laid and jointed (in CM 1:1) complete with collars all as specified & as directed.

M&L for construction of soakage well excavation in ordinary soil, founadation in PCC 1:3:6, well of honey combed brick masonry in CM 1:4 and solid in M-25 concrete including intercepting chamber, screen chamber brick work in CM1:6, RCC over slab in M-25/RR masonry in CM 1:4, filling with brick bats of size 2.4 m dia and 3.00 m deppth, complete all as specified and shown in drg No. CEBZ/TD/78/2011 Sheet 1/2 & 2/2.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc.

Disconnecting and taking down unserviceable sub main wiring of any size including steel/PVC conduit and accessories & removing from site and making good the disturbed surfaces, complete all as specified and directed.

Taking down carefully by unscrewing from boards / outlet boxes, fittings and fixtures such as switches, sockets etc for re use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed

M&L for point wiring with 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed cable in and including PVC rigid non metallic conduit medium grade not less than 20mm dia ISI marked and fittings and accessories concealed in walls/roof/ ceiling with suitable size of sunk type pressed steel modular terminal box and modular white cover plate with frame for suitable module as per site requirements for mounting of modular switches, sockets, fan regulator etc and one green colour cable of 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed as earth wire up to common earth and connected to earth for the following, complete all as specified and directed:

One light point controlled by one, one way switch.

One Ceiling fan/wall fan/exhaust fan controlled by one, one way switch.

One three pin 5 Amp socket on same board with other switches.

One three pin 5 Amp socket on independent board.

All as per item No. 92.00 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 1.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth.

S&F modular switch 1 way 6/10Amp , 1 module, complete all as specified and directed.

S&F modular switch 1 way 16Amp, 1 module, complete all as specified and directed.

S&F modular socket 6Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F mdoular socket 6Amp/16 Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F mdoular ceiling fan regulator, stepped (four step) complete all as specified and directed.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm.

Taking down existing ceiling fan/exhaust fan & wall mounted fan and re-use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed

S&F lamp holder PVC/polycarbonate type with back plate complete all as specified and directed. Make : Cona / SSK / Havells

S&F exhaust fan AC single phase 230/240 volts of size 300mm sweep with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified & directed. Make: Crompton/Havells/Usha.

Supply and fixing LED box type tube light fitting 20 watt made up of CRCA sheet with pre wired double sided connections including 1x20 watt retrofit LED tube rod with extruded aluminium body , PC diffuser and inbuilt driver , double sided connection, complete with all accessories internally prewired . Make :- Havells/Bajaj/Philips/Crompton as Approved by AO.

Supply and fixing wall mounted decorative luminarie fitting suitable up to 9/10 Watt LED lamp champagne gold finish fixture with plastic body suitable for B22 Base complete all as specified and directed by Engr-in-Charge. Make: Havells , Model- LHFOECE1TZ1O014, HSN Code: 9405 or equivalent model of Mepro/Philips

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. Make :- Havells/ Bajaj/ khaitan/Usha as Approved by AO.

S&F LED light fittings, 10 W bulk head luminaries 230V, 50 Hz complete with all accessories and including connecting up with three core copper conductor cable with suitable size complete all as specified and directed. Make:- Bajaj/Havells/CG as Approved by AO.

Supply and fixing and testing energy saving street light luminaire 25 watt LED , pressure die cast housing with high power LED as lighting source and lens embedded PC cover with IP 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge. Make :- Havells / Surya/Control& Switchgear/Bajaj as Approved by AO.

Supply and fixing recess mounted 2' x 2' LED luminarie 36 watt, cool day/warm light with white powder coated CRCA housing with LED driver, efficiencey >100 Lm/w complete all as specified and directed. Make Crompton/Havells/Philips

Supply and fixing street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts complete all as specified and directed.

Supply & fixing ceiling fan 1200 mm sweep , 230 Volts, AC , 50 Hz, copper winded motor, BEE 5 star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy, complete, all as directed by Engr-In-Charge. Make: Crompton/Havells/Usha.

S&F exhaust Fans AC single phase 230/240 volts of size 300 mm sweep with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed. Make: Crompton/Havells/Usha.

S&F ventilation fan 250mm sweep non metallic white colour including connecting with three core flexible copper wire from ceiling rose to connector of fan, complete, all as specified and directed.Make: Crompton/Havells/Usha.

M&L for TV socket including PVC conduit and coaxial cable wire, all as directed by EIC. Make :- Havells/ Bajaj/ CG as Approved by AO.

M&L Telephone socket including PVC conduit and telephone wire, complete all as directed by EIC. Make :- Havells/ Bajaj/ CG as Approved by AO.

S&F Change over switch, TPN, AC 63 Amp with bolted type fuse in sheet enclosure with fuses including taking down old chage over switch, complete all as directed by EIC.

M & L for submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 6 sqmm multi stranded copper conductor cable drawn through and incl 25 mm dia PVC non metallic rigid concealed conduits and the conduits accessories incl one run of green colour earth continuity conductor with 6 sqmm multi stranded copper conductor cable.

M & L for submain wiring with two single core, PVC insulated, unsheathed, FRLS, 1100 volts grade 2.5 Sqmm multi stranded copper conductor cable drawn through and including 25 mm dia PVC non metallic rigid conduits & conduits accessories, concealed in wall/ roof/ ceiling ncluding one run of green colour earth continuity conductor with 2.5 Sqmm multi stranded copper conductor cable complete all as specified and directed. Note :- Two run of single core cable, one run of earth continuity conductor & conduit with conduit accessories shall be measured as one unit length.

S & F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB SP `C' series for AC complete all as specified and directed

Disconnecting all electrical connections and taking down window type/split type air conditioner of capacity 1.5/2 Ton and re-installing in its original position after refilling of refrigerant or gas and making all required connections and commissioning complete all as specified and directed. Note :The rate considered is inclusive of tools and plants.

S&F of MCB distribution board TPN 4 way, 415 volts, double door, with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43 , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCBs as incomer and outgoing including blanking plate complete all as specified and directed.

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed.

S & F of MCB SPN, 240 volt, 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SPN, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S&F of MCB TPN, 415 volt, 63 Amp capacity,10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SP, 240 volt, 6 Amp to 40 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade in replacement with stranded aluminium conductor of size 16 sq mm 4 core complete all as specified and directed.

Supply and fixing tubes light grade GI tubing 40 mm dia with all fitting laid in trenches, fixed on pole/on wall for cable protection .

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, laying cable and getting out in any type of soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose/ hard/ dense soil complete all as specified and as directed.

Removing excavated material (soils) not exceeding 50 m and depositing where directed at a level n exc. 1.5 m above the starting point

Supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed . Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly.

M & L for laying of bricks locally available sub class 'B' bricks, non-modular sizes as per IS 1077: 1992 for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable all as directed.

kirtiman traders

SHREE BALAJI TRADING CORPORATION

ANAM BUILDCON

R.S BUILDERS