Certain repairs to joinery, plumbing, flooring and sunken treatment to OTM accn of Bde CP, Sig TEPTA, Fd Wkp and Ary-I under AGE B/R-I, GE Gurdaspur.

Amount

Demolition of cement concrete of any description and in any position (above/below of ground level) not otherwise specifically provided as in sunken floor, plinth protection, roof kerb, foundation etc. all as specified and directed.

M&L plaster 15mm thick in cm 1:3 in sunken portion of slab finished fair and even using waterproofing compound all as specified and directed Note : Water proofing compound shall be measured and paid separately.

Supply only integral water proofing compound.

M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) laid on primed surface including bitumen primer @ 0.40 kg /Sqm by forced application with butane torch over entire roof area with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in after cleaning surface complete all as specified and directed and all as per manufacturer's instructions.

M&L for PCC 1:5:10 type E2 using 40 mm graded stone agg as in filling, fdn and mass concrete in sunken floor complete all as specified and directed.

M&L 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in sub base for receiving the floor finishes complete all as specified and directed.

M&L for ceramic glazed dark shade coloured tiles of size 350x250x 7mm/ 450x350x7mm thick joint free on and including 10mm thick screed bed in CM(1:4) set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles on vertical surfaces of wall as in skirting/ dado and dismantling of existing tiles and screed complete all as specified.

M&L for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm to 0.18sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in CM 1:6 and dismantling of existing tiles and screed complete all as specified.

M&L for Green Marble work 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars window cills, cooking platforms, stair case and like in cement mortar ( 1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 15 mm thick screed bed in CM 1:4 and dismantling of existing marble and screed complete all as specified and directed.

M&L for dark coloured vitrified tiles10 mm thick joint free (square/rectangular) area of each tile n exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in CM 1:6 and dismantling of existing tiles and screed complete all as specified.

Dismantling of roof brick tiles fixed in cement mortar in single layer complete all as directed.

Demolition mud phuska in roofs any thickness including plastering and leeping complete all as specified and directed.

Roughing the surface of old concrete floor picking sweeping clean and washing down with water to remove dust/mud etc.and brushing neat cement slurry @ 3kg/Sqm.

M&L for cement concrete 1:2:4 type B-0 using 12.50mm graded stone aggregate as in roof padding finished even and smooth without using extra cement to maintain slope complete all as specified.

M&L for 40 mm thick brick tiles laid over and including 15 mm thick cement mortar 1:6 mixed with water proofing compound as per manufacturer's instructions. Joints grouted and flush pointed in cement mortar (1: 3) mixed with 5 % of crude oil by weight of cement, flush pointing in cement mortar (1:3) shall be done as a separate process, complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

All a per Srl item No 15 above but except tiles (old serviceable dismantled tiles obtained from Srl item No 11 shall be reused after necessary cleaning of mortar)

M&L for 75mm thick cement cocnrete type C-1 (1:3:6) (20mm graded aggregate) as in plinth protection finishing the surface even and fair complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone agg) as in roof kerbs or mud stops, rounded or chamfered on edges with WPC complete all as specified and directed by Engineer-in-Charge. Note : WPC shall be measured and paid separately.

Demolition of brick work or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc

M&L for brick work with sub class 'B' old size bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

Material and Labour for repairing of RCC projections, chajjas, roofs, facia etc. by necessary preparations i.e. scrapping, cutting, chiseling, dusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1 : 2 : 4) using 12.5mm graded crushed stone aggregate and finished with cement sand mortar (1:3) using coarse sand in patches area n.exc 5 Sqm each and thickness of RCC member exc 50mm including applying two coats of Finishes to match with the existing surfaces in at any height complete all as specified. Note: - Cost of formwork, bldg ht upto 12m, shall be deemed to be included in unit rate quoted by the Contractor.

Taking down cement plaster of any description on brick walls on concrete surfaces etc including racking out joints hacking for key,scrubbing down with water etc from walls and ceiling surfaces of any description complete all as specified and directed.

M&L for rendering 15mm thick plaster in cement mortar 1:4 on brick or concrete surfaces of walls, finished surface even and fair with WPC upto ht. 12 mtr complete all as specified and directed by Engineer-in-Charge. Note : WPC shall be measured and paid separatel

M&L for rendering 12mm thick plaster in cement mortar 1:6 on brick or concrete surfaces of walls, finished surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 5mm thick plaster on ceiling in cement mortar 1:3 finished surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L preparation of new plaster surface and applying two coats of cement base paint on wall surface complete all as specified and directed.

M&L preparation of new plaster surface of wall and applying two coats of Oil bound distemper over a coat of chalk whiteing primer on plastered surface wall complete all as specified and directed.

M&L preparation of new plaster surface and applying three coat of white wash on wall complete all as specified and directed.

M&L preparation of new plaster surface and applying three coat of white wash on ceiling complete all as specified and directed.

S&F steel window box type made of ERW tube, hollow P section of size 60mmX25mm double rebated outer frame comprising double skeleton shutters i.e. guaged & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 including one shop coat of priming and two coats of synthetic enamel paint and taking down old existing window complete:- (i) Thickness of the sheet shall be of 18 gauge (ii) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (iii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iv) MS Tower bolt 150mm long-02 Nos per leaf (v) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (vi) Cleat 55mm long of hollow square 15mmX12mm -01 Nos per leaf (vii) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (viii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). Note: Wire cloth, glass, shall be measured and paid for separately

S&F steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts, including one shop coat of priming and two coats of synthetic enamel paint including taking down old existing window/ ventilator complete all as specified and directed. Notes: (i) Thickness of the sheet shall be of 18 gauge. (ii) Glass/ wire mesh, shall be measured and paid for separately

S&F anodised aluminium door shutters, aluminium section weighing average not less than 1.00kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. incl taking down old existing complete all as specified.

S&F anodised aluminium window/ ventilator shutters side hung type without sash bars, aluminium section weighing average not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) incl taking down old existing complete all as specified.

S&F anodised aluminium frame for doors, windows, ventilators, partitions with one or more rebates including joining cleat for fixing etc.incl taking down old existing and complete all as specified.

S&F 4.8mm thick black sheet glass ordinary quality in squares or rectangular not exceeding 1.00 sqm in each pane in aluminium door or window shutter complete all as specified and directed

S&F in repair 4.8mm thick black sheet glass ordinary quality in squares or rectangular not exceeding 1.00 sqm in each pane in aluminium door or window shutter complete all as specified and directed

Petty repair to existing in built Aluminium Door , locks, hinges incl necessary making the lock/Glass/ adjusting shutter complete serviceable all as per existing pattern as directed by Engineer-in-Charge incl provision of duplicate keys as required.

S&F in repairs Mortice lock ,aluminium vertical type size 65mm 2 levers complete all as specidfed and directed.

S&F in repairs Aluminium (Die cast) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

S&F in repair Floor door stopper 140 mm size of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floorcomplete complete all as specified and directed by Engineer-in-Charge.

Repairs, easing & adjusting of shutter without taking down shutters of any description exc 1.00 sqm & nexc 2 sqm each.

Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter from the chowkats) complete all as specified and directed.

Taking down chowkats with shutter exc 1.50 Sqm but n exc 4.00 sqm each (without taking off shutter from the chowkats) complete all as specified and directed.

Taking down shutter of any description exc 1.00 Sqm but n.exc 2.00 Sqm each complete all as specified and directed.

Supply and fix for pressed steel frames of size 105 mm x 60 mm for doors with one or more rebates including necessary lugs, hinges, lock strike plate, as per ISI mark, including PCC (1:3:6), type C-0,( using 12.5 mm graded stone aggregates) as in filling of pressed steel frames including one shop coat of priming and two coats of synthetic enamel paint complete all as specified and as directed .

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

S&F 30 mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels on both side complete all as specified and directed.

S&F 2nd class hard wood (Hallock) factory made glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc. but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc , sizes of members of shutters as specified in SSR Part-I, Section 8 clause 8.24 (a) complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F in repair Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each complete all as specifiwd and directed.

S&F in repair 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each incl hacking out of old broken glass panes from wooden or steel frame complete all as specified and directed.

M&L for preparation of new wooden surface exc 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S&F in repair 300 mm long mild steel ordinary rat tail rod pattern spring, including roller and roller plate including fixing through welding/bolts/ screws in metal/wooden frame complete all as specified and directed.

S&F Aluminium anodized barel tower bolt of extruded section 150mm long ISI marked complete all as specified and directed.

S&F aluminium alloyed handle fabricated type anodized of size 150 mm long complete all as specified and directed.

S&F 100mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 through bolt or with screw complete all as specified and directed.

S&F Aluminium alloy, anodised, 300 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified and directed.

Supply and fixing in repair cutrain rod 20mm dia of Mild steel with PVC Coated with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug including taking down existing curtain rod complete all as specified and directed.

S&F in repair 18 mm thick plywood, grade BWR, laminated on both side with decorative choice lamination, fire resistant, moisture resistant type fixed with screws to timber/steel frame work Incl 6mm thick lipping of 2nd class hard wood fixed with nails on all sides complete all as specified and directed.

S&F aluminium alloyed handle fabricated type anodized of size 100 mm long complete all as specified and directed.

S&F 75mm size hasp and staple safety type aluminium anodised brass with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed.

S&F in repair 7-8 mm thick PVC hollow wall panelling consisting of wood grain printed pvc sheet inclusive of solvant cement and fixing at site on PVC frame formed by sticking high density EPS, flame retardent (TF) grade, heavy duty with tipper strip weather proof, water proof, termite proof including all C and U type PVC section with matching of panelling fixing at border of panelling and complete all as specified and directed by Engr-In-Charge.

S&F 500 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks ISI marked (cylindrical vertical with closed top) hoisted and fixed in postition all as specified in SSR Part I including dismantling of water tanks complete all as specified and directed.

S&F 1000 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks ISI marked (cylindrical vertical with closed top) hoisted and fixed in postition all as specified in SSR Part I including dismantling of water tanks complete all as specified and directed.

S&F 2000 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks ISI marked (cylindrical vertical with closed top) hoisted and fixed in postition all as specified in SSR Part I including dismantling of water tanks complete all as specified and directed.

S&F in repair ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore complete all as specified and directed.

S&F in repair stop valve 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repairs vitreous china wash down water closet (pedestal pattern) fixing with bolts, white, including stainless steel L-type jet spray with 1 m hose pipe, plastic water closet white closed pattern with flat bottom and cover with mild steel chromium plated hinging device and fixing bolts, connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified and directed.

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with integral foot rest with PVC `P’ or `S’ trap, integral foot rest including connection to trap and flushing pipe etc complete and bedding in PCC 1:7:12 type F-2 complete all as specified and directed.

S&F in repair vitreous China wash basin, with full pedestal white flat back, size 550x 450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets and waste coupling of PTMT (half or full threaded) (minimum weight 45gms) for 32mm bore dia discharge pipe complete all as specified and directed.

S&F in repair vitreous China table top wash basin, white rectangular bowl, size 550X400X140mm including 32mm size Cast copper alloy CP waste coupling complete all as specified and directed. Make: Cera or equivalent as per appx 'B'.

S&F in repair vitreous china Urinal, Half stall type, white (excluding flushing cistern) white with grating, waste coupling and union for discharge pipe complete including providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screw, pointing aroug urinal back in cement, grating and union for discharge pipe incl PTMT waste coupling, waste pipe, urinal spreader complete all as specified and directed.

S&F in repair PVC waste pipe 32mm dia 800mm to 1000 mm long fixed to wash fitting of wash basin and sink all as specified and directed.

S&F in repairs 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle, 32mm dia PVC flush pipe and connections, joints to pipes, making good the disturbed surfaces complete all as specified and as directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair stop valves or angel valve cast copper alloy 15mm bore fancy type chromium plated alloy with butterfly handle screwed down for high pressure, screed on both ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repair bib taps cast copper alloy 15mm bore fancy type chromium plated alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair Pillar taps, cast copper alloy fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore and fixed.

S&F GI tubing 15mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked including taking up and down complete all as specified and directed.

All as per Srl item No 82 above but fixing only (old serviceable pipe re-used including cleaning and new fittings).

S&F GI tubing 20mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings ISI marked including taking up and down complete all as specified and directed.

S&F GI tubing 32mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings, ISI marked including taking up or down old pipe complete all as specified and directed.

Dismantling of cast iron, PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches, if required.

S&F PVC (SWR) pipes 110mm dia in any length with rubber ring joint fixed to wall/ floor upto 12m height complete all as specified and directed.

S&F PVC (SWR) pipes 75mm dia in any length with rubber ring joint fixed to wall/ floor upto 12m height complete all as specified and directed.

S&F in repair PVC (SWR) bends 110mm dia, in any radius, complete all as specified and directed.

S&F in repair PVC (SWR) bends 75mm dia, in any radius, complete all as specified and directed.

S&F in repair 110 bore PVC(SWR) Branch pieces (Single T), single (equal or unequal ) with oval access door complete all as specified and directed.

S&F in repair 75 bore PVC(SWR) Branch pieces (Single T), single (equal or unequal ) with oval access door complete all as specified and directed.

S&F in repair PVC vent cowl of size 110mm.

M&L in repair for PVC(SWR) floor trap plain including jointing with solvent cement 100mm dia complete all as specified and directed.

M&L in repair for PVC(SWR) floor trap plain with grating including jointing with solvent cement 75mm dia complete all as specified and directed.

S & F Stack clamps (110 mm pipe) out of 20 mm by 1.5 mm galvanised Mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S & F Stack clamps (75 mm pipe) out of 20 mm by 1.5 mm galvanised Mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F in repair Grating doom 100 mm dia with waste hole of PTMT complete all as specified and directed.

S&F in repair Brass chromium plated shower rose fancy type 125mm size with swivel joints, any size, including fixing to steel pipe or union with brass CP arm 195mm long, 15 mm size complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia, D type, 60 cm long with flanges complete all as specified and directed by Engr-in-Charge.

S&F in repair brass spindle with nylon washer and removing leakage of water of any concealed type suitable for 15mm bore pipe complete all as specified.

S&F in repair tap/valve head/ handle 15mm dia cast copper alloy fancy type chromium plated round/square hole complete all as specified and directed.

M&L for pre cast cement concrete louvers and jali 1:2:4 type B-O (Using 12.5 mm graded aggregate) 25 mm thick set in cement plaster in CM (1:4) including taking down complete all as specified and directed. .

S&F in repair stainless steel L-type jet spray with 1m hose pipe for fitting in WC complete all as specified and directed by Engineer-in-Charge.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified complete all as specified as directed

S&F in repair Vitreous china coloured WC italion finish pedestal pan with attached vitreous china flushing cistern (monolithiic type) of push button type having dual flushing cistern of same colour including pvc seat cover same colour including brass Jet chromium plated with pvc connection 15mm bore complete all as specified and directed.

M&L PCC (1:4:8), type D-2 (using 40 mm graded stone aggregate), as in sub base floor finished fair and even, to raise level only complete all as specified.

Dismantling of existing tiles and M&L for 60 mm thick PCC (M-35) factory made with grey cement and pigment interlocking tiles/ paver block of shape/ size as conforming to IS 15658, joints will be filled with fine sand, complete all as specified and as directed by Engr-in-Charge.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

M&L for Chequered cement concrete tiles with grey cement and pigment 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry incl 15mm thick 1:4 CM screed bed including dismantling of existing tiles and screed complete all as specified and as directed.

S&F machine cut kota stone slab flooring 20-22mm thick over cement screed base 20mm thick in 1:6 jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (with bees wax polish) including demolition existing slab and screed complete all as specified and directed.

M&L Perforated particle board/tiles 12 mm thick for insula-tion and accoustic purposes, 60x60 cm in size, fixed with nails to timber frame work or with staples on snap grid fixed in ceiling incl dismantling of existing board with frame work complete all as specified and directed by Engr-n-charge. Note:-Frame work for ceiling shall be measured and paid separately

S&FGI powder coated grid work of size 605mm X 605mm, with main tee of size 32mm X 23.5mm x 1.5mm thick, cross tee of size 25mm X 23.5mm x 1.28mm and angle of size 23.5mm X 23.5mm x 1.2mm fixed on wall, all powder coated finish on exposed faces of tee and angle, hung from ceiling using 2mm dia. G.I. suspension wires and 'J' bolts, washers, nuts spaced at 1200 mm both ways including making niches for fans/ light complete all as specified and as directed.

S&F in repair 15 mm brass CP WHB mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repair of 4mm thick aluminium composite pannel (ACP) sheet for aluminium door/window complete all as specified and directed by Engr-in- charge.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete upto 12 m height all as specified and directed.

Form work to rough finished surface of concrete flat to soffits of shelve, chajja, fins etc including supports over hangs

S&F 6mm dia and over TMT bar cut to length bent to shaps including cranking binding spirraly, hooping, hooking end and binding with MS wire (anealed) not less then 0.9 mm dia or securingwith clips as specified.

M&L for RCC in 1:2:4 type B-1(using 12.5 mm graded stone agg) as in chajjas facia, shelves etc and similar work all as spd.

S&F Vinyl wall paper of approved shade/design over wall with adhesive all as per manufactures instruction including removing existing complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to walls,fixed with self tapping screws as specified.

Dismantling framed work of timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as directed.

S&F of Rolled mild steel Gde Fe-410-W Gde E-250 Quality-A in Roof trusses (framed), trussed, purlins crane gantries, joist, channel, steel tube, rails & fastenings & heavy brackets framimg, strips, door, shutter (Beam, tee, angle, Coulmn, Gusset Plates, channel, Hollow square/Rectangular or flat section) including distance pieces, cleats with riveted, bolted or welded attachment etc. complete all as specified and directed.

M&L for preparation of new steel surface exc 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete etc.

S&F in repair Vitreous china counter top oval wash basin, snow white, size 560x400x205mm, including 32mm size Cast copper alloy CP waste coupling and waste pipe complete all as specified and directed. Make: Cera or equivalent as per Appx 'B'.

Servicing of rolling shutters of any type any Size and oiling and greasing all moving parts of rolling shutters, realignment of anchoring rod, checking and made functional/ operateable all moving strips / parts including minor repair tightening of springs, nut & bolts, welding repair, proper fixing of loose side guard of rolling shutter, repair of both side locking arrangements etc complete all as specified and directed.

Taking down existing u/s rolling shutters of any type any size and refixing the same in situ after necessary welding work, oiling and greasing, replacement of unserviceable bearings, realignment of anchoring rod, checking and made functional / operate able all moving strips/ parts to the entire satisfaction of the engineer in charge complete including replacing of damaged strips all as specified. (Note :- (i) S&F Strips shall be measured & paid separately under appropriate item. (ii) Rates are deemed to inclusive of all civil works required for refixing and making good the disturbed surfaces).

S&F in repair Safety lever locks mild steel with 4 levers for rolling shutters fixed in repairs complete all as specified and directed by Engineer -in-Charge.

S&F in repair Bevel type gear box of suitable size fixed in repairs and making good the distrubed portion (concrete/ brick) and match the existing surface complete all as specified and directed.

Taking down existing iron door/shutter of any type any size and refixing the same in situ after necessary welding work, oiling and greasing, replacement of unserviceable MS section, realignment , checking and made functional / operate able all moving parts to the entire satisfaction of the engineer in charge complete all as specified. (Note :- (i) S&F MS section shall be measured & paid separately under appropriate item. (ii) Rates are deemed to inclusive of all civil works required for refixing and making good the disturbed surfaces).

S&F in repair Vitreous china urinal partition white of size 310x700 mm fixed with wall by steel screws complete all as specified and directed.

Preparation of old surface by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots. on existing distempered surfaces and applying two coats of Oil bound distemper on ceiling complete all as specified and directed.

Preparation of old surface by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots. on existing distempered surfaces and applying two coats of interior acrylic emulsion paint over a coat of 1mm thick wall putty on wall complete all as specified and directed.

Preparation of old surface by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots. on existing distempered surfaces and applying two coats of oil bound distemper over a coat of plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth on ceiling complete all as specified and directed.

M&L in repair for 20mm thick Granite (of any type) work, machine cut (table rubbed and polished) on cooking platforms, window cills, steps, pillar and floor, set in neat grey cement slurry @3 Kg/Sqm laid over and including 20mm thick bedding layer in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including cutting, grinding & polishing complete all as specified and directed.

S&F in repair push type auto closing angle valve cast copper alloy 15mm bore fancy type chromium plated for high pressure, screed on both ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repair push type auto closing long nose pillar taps, cast copper alloy fancy type with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long scrfewed shanks and fly-nuts, screwed for iron pipe 15mm bore and fixed.

S&F in repair stainless steel cockroach trap with waste hole, square size 127mm x 127mm complete all as specified and directed.

M&L for preparation of old plastered surface of walls rubbing down, making good holes, cracks etc and stopping etc on existing distempered surfaces and applying one coats of oil bound distemper on wall complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall by brooming down, making good holes, cracks and appling two coats of white wash ht upto 12m complete all as specified and directed.

M&L for preparation of old plastered surface of walls rubbing down, making good holes, cracks and stopping etc on existing surfaces and applying one coat of cement base paint on wall ht upto 12m complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceiling by brooming down, making good holes, cracks and applying one coat of white wash complete all as specified and directed.

Note: A Schedule of Credit for old/unserviceable demolished/dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

S S CONSTRUCTION