Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹5.0 LAccepted-AOC LIG 10 VIVEK NAGAR NAVIBAGH BHOPAL MADHYA PRADESH 462038 | BHOPAL | MADHYA PRADESH | 462038 | L1 | Accepted-AOC Being Lowest | |
| 2 | L2₹5.2 L+₹17,505 (3.50%)Rejected-Finance | L2 | Rejected-Finance Being NOT Lowest | |
| 3 | L3₹5.9 L+₹87,568 (17.5%)Rejected-Finance | L3 | Rejected-Finance Being NOT Lowest |
Tender Value
₹7.5 L
EMD Value
₹15,000
Closing Date
11 Jan 2020, 6:00 pmClosed
GE BHOPAL
GE BHOPAL
REPAIR AND MAINT OF PUMP SETS, BORE WELL AND ALLIED WORKS AT BAIRAGARH UNDER GE BHOPAL.
2019_MES_307835_1
8608/E8
Open Tender
Electrical and Maintenance Works
Item Rate
183 days
BHOPAL
Class E
Category b i
6 documents required · 6 mandatory
₹500
Yes
GE BHOPAL
₹15,000
Yes
27 Feb 2020
19 Dec 2019
13 Jan 2020
19 Dec 2019
11 Jan 2020
2 Jan 2020
Amount
M&L for taking out unserviceable submersible pumping set complete with column pipe any type & capacity and any type from existing bore well carefully without damaging the pump set including connecting parts and lowering the same after repair including provision of suitable size of nut & bolts with washer and suitable packing for column pipes and connection of submersible cable complete all as specified and directed. NOTE: (i) Length of column pipe in borewell shall be measured for the purpose of payment. (ii) Chain pully block , clamps, etc shall be provided by the contractor. (iii) Necessary safety pracaution will be responsibility of the contractor.
Disconnection and dismantling of centrifugal /submersible /monoblock /pressure pump/ non clog motor pump /VT pump set assy, etc from foundation located at variuos places under AGE E/M Bairagarh; transportation of the pump to workshop for repairs; dismentling and opening of the pump assy for checking out defects; taking out shaft from pump and carrying out lathe work on shaft foe checking and making straightness; taking out of old worn out brass impeller; material and albour for filling material on worn out parts, grinding, polishing and carrying out complete lathe work, refixing of shaft and checking its smooth functioning and balancing and reassembling of pump; transporation back to site as directed by Engineer-in-charge and fixing to its existing /new location with new nut, bolt, washers, etc as required and making electrical connections and testing complete all as specified & directed. NOTE:- (i) Spares/parts shall be paid under relevent item here-in-after under as supply only. (ii) Cost of Minor spare parts; which are not included in subsequent items given here-in after but are required for making the making the motor functional is deemed to be included in the quoted basic rate.
240 HP motor
50 to 65 HP motor
30 to 45 HP motor
10 to 25 HP motor
Dismantling of submersible any type and taking out unserviceable spares and burnt copper binding wire and M&L for rewinding of submersible motor with insulated copper winding wire including sleeves (as per manufacturers specification) and replacement of worn out parts, including grinding & polishing of rotor sleeves and refixing, testing and transport charges complete all as specified & directed. NOTE:- (i) Spares/parts shall be paid under relevent item here-in-after under as supply only. (ii) Cost of Minor spare parts; which are not included in subsequent items given herein-after but are required for making the making the motor functional is deemed to be included in the quoted basic rate.
7.5 to 15 HP Motor
Supply only the following parts suitable for submersible pump and motor of capacity 7.5 to 15 HP of make as per original manufacturers specification complete all as specified & directed. NOTE:- Cost of Minor spare parts; which are not listed below but are required for making the making the motor functional is deemed to be included in the quoted basic rate of respective item.
Bowl bush
Impeller
Neck ring
Shaft sleeve
Pump shaft
Coupling
Coupling key
Impeller key
Stud with nuts
Thrust bearing
Lower housing bush
Upper housing bush
Rotor shaft sleave
Drain plug
Water seal
CI Bowl
Rotor Shaft
Bearing suitable for pump set
Dismantling of Centrifugal/ Monoblock/ Pressure motors, etc any type and taking out unserviceable spares and burnt copper binding wire and M&L for rewinding of motor with insulated copper winding wire including sleeves (as per manufacturers specification) and replacement of worn out parts, including grinding & polishing of rotor sleeves and refixing, testing and transport charges complete all as specified & directed. NOTE:- (i) Spares/parts shall be paid under relevent item here-in-after under as supply only. (ii) Cost of Minor spare parts; which are not included in subsequent items given herein-after but are required for making the making the motor functional is deemed to be included in the quoted basic rate.
240 HP Motor
50 to 65 HP Motor
30 to 45 HP Motor
10 to 25 HP Motor
Supply only the following parts suitable for centrigual pump and motor of capacity 240 HP of make as per original manufacturers specification complete all as specified & directed. NOTE:- Cost of Minor spare parts; which are not listed below but are required for making the making the motor functional is deemed to be included in the quoted basic rate of respective item.
Bowl bush
Impeller
Neck ring
Shaft sleeve
Pump shaft
Coupling
Coupling key
Impeller key
Stud with nuts
Thrust bearing
Lower housing bush
Upper housing bush
Rotor shaft sleave
Drain plug
Water seal
CI Bowl
Rotor Shaft
Bearing suitable for pump set
Supply only the following parts suitable for Centrifugal/ Monoblock/ Pressure motors, etc and motor of capacity 50 to 65 HP of make as per original manufacturers specification complete all as specified & directed. NOTE:- Cost of Minor spare parts; which are not listed below but are required for making the making the motor functional is deemed to be included in the quoted basic rate of respective item.
Bowl bush
Impeller
Neck ring
Shaft sleeve
Pump shaft
Coupling
Coupling key
Impeller key
Stud with nuts
Thrust bearing
Lower housing bush
Upper housing bush
Rotor shaft sleave
Drain plug
Water seal
CI Bowl
Rotor Shaft
Bearing suitable for pump set
Supply only the following parts suitable for Centrifugal/ Monoblock/ Pressure motors, etc and motor of capacity 30 to 45 HP of make as per original manufacturers specification complete all as specified & directed. NOTE:- Cost of Minor spare parts; which are not listed below but are required for making the making the motor functional is deemed to be included in the quoted basic rate of respective item.
Bowl bush
Impeller
Neck ring
Shaft sleeve
Pump shaft
Coupling
Coupling key
Impeller key
Stud with nuts
Thrust bearing
Lower housing bush
Upper housing bush
Rotor shaft sleave
Drain plug
Water seal
CI Bowl
Rotor Shaft
Bearing suitable for pump set
Supply only the following parts suitable for Centrifugal/ Monoblock/ Pressure motors, etc and motor of capacity 10 to 25 HP of make as per original manufacturers specification complete all as specified & directed. NOTE:- Cost of Minor spare parts; which are not listed below but are required for making the making the motor functional is deemed to be included in the quoted basic rate of respective item.
Bowl bush
Impeller
Neck ring
Shaft sleeve
Pump shaft
Coupling
Coupling key
Impeller key
Stud with nuts
Thrust bearing
Lower housing bush
Upper housing bush
Rotor shaft sleave
Drain plug
Water seal
CI Bowl
Rotor Shaft
Bearing suitable for pump set
Supply only the following parts of 15/20 HP Non clog pump and motor of make as per original manufacturers specification complete all as specified & directed. NOTE:- Cost of Minor spare parts; which are not listed below but are required for making the making the motor functional is deemed to be included in the quoted basic rate of respective item.
Bearing
Impeller
Ishpenter bush
Neck ring (04 Nos)
Shaft turning (04 Nos.)
Bush (04 Nos)
Rotor seal
Bowl bush
Neck ring
Shaft sleeve
Pump shaft
Coupling
Coupling key
Impeller key
Stud with nuts
Thrust bearing
Lower housing bush
Upper housing bush
Rotor shaft sleave
Drain plug
Water seal
CI Bowl
Rotor Shaft
S&F in replacement fully automatic star delta starter in sheet metal enclosure, type MN, with single phase protection features, heavy duty, 3 phase, 415 volt, suitable for submersible motor pump set upto 15 HP (11kW) with all necessary internal wiring complete all as specified and directed. [Make :- L&T (Cat No.SS94362) or equivalent in Legrand/C&S as approved by GE]
S&F in replacement fully automatic star delta starter in sheet metal enclosure, type MN, with single phase protection features, heavy duty, 3 phase, 415 volt, suotable for submersible motor pump set upto 75 HP (55kW) with all necessary internal wiring complete all as specified and directed. [Make :- L&T (Cat No.SS94362) or equivalent in Legrand/C&S as approved by GE]
S&F in replacement 3 core, flat, 6 sqmm size, ISI marked, 1100 volt grade, PVC insulated & PVC sheathed copper conductor water proof flxible cable (submersible type) with jointing lugs and other material/kit including testing after jointing one end of cable to submersible motor & other to the starter complete all as specified and directed. [MAKE: HAVELLS/POLYCAB/FINOLEX/V-MARC as approved by GE]
S&F in replacement DOL Starter, 415 Volt, suitable for 7.5 HP motor with sheet steel enclosure, type MK-1, relay max range 13-22 amp complete all as specified and directed. [Make :- L&T (Cat No -SS96228) or equivalent in Legrand/ Seimens/Schinider as approved by GE]
S&F in replacement electronic timer for Star Delta Starter type, timing range 3-30 sec, 415 V, 50 Hz complete all as specified and directed. [Make :- L&T (Cat No -ST80328000) or equivalent in Legrand/ Seimens/ Schinider/ Havells as approved by GE]
S&F in replacement single phase preventor relay, type SDz5 with settable time ON delay 30-300sec complete all as specified and directed. [Make :- L&T (Cat No -XM81808OOOO) or equivalent in Legrand/ Seimens/ Schinider /Minilac as approved by GE]
S&F in replacement power contactor, type ML-6, 3 pole, 415 V, 50Hz, 3 Phase with auxilary contacts 2 NO + 2 NC complete all as specified and directed. [Make :- L&T (Cat No -SS90921) or equivalent in Legrand/ Seimens/ Schinider as approved by GE]
S&F in replacement power contactor, type ML-4, 3 pole, 415V, 50Hz, 3 Phase, with auxilary contacts 2 NO + 2 NC complete all as specified and directed. [Make :- L&T (Cat No -SS90910) or equivalent in Legrand/ Seimens/ Schinider as approved by GE]
S&F in replacement Thermal overload relay, type MN-5, with relay setting range (Amp) 45-75, 415V, 50Hz, 3 Phase with built-in single phasing protection complete set and all as specified and directed. [Make :- L&T (Cat No -SS9413700JO) or equivalent in Legrand/ Seimens/ Schineder as approved by GE]
S&F in replacement Thermal overload relay, type MN-5, with relay setting range (Amp) 45-75, 415V, 50Hz, 3 Phase with built-in single phasing protection complete set and all as specified and directed. [Make :- L&T (Cat No -SS9413700JO) or equivalent in Legrand/ Seimens/ Schineder as approved by GE]
Deduct schedule of credit (calculation will be done off line) Rs.83,998.00
RAJPATI CONSTRUCTION
ROYAL CONSTRUCTION
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .