Repair and Renovation of Registrar Chamber at High Court Building under SD-II, PBSD, APWD, Port Blair

Amount

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Of area 3 sq. metres and below

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

1st class Padauk wood / 1st class Teak wood Cat- I (A)

Providing wood work in frames of false ceiling, partition etc. sawn and put up in position :

1st class Padauk wood / 1st class Teak wood Cat- I (A)

Providing and fixing 35 mm thick panelled glazed or panelled and glazed shutters for doors, including brass butt hinges fixed with necessary brass screws etc. all complete with 1st class Padauk wood / 1st class Teak wood Cat- I (A) including panelling with 25 mm thick 1st class Padauk wood / 1st class Teak wood Cat- I (A) as directed by the Engineer-in-charge.

1st class Padauk wood / 1st class Teak wood Cat- I (A)

Providing wall panelling with 25 mm thick 1st class Padauk wood / 1st class Teak wood Cat- I (A) by making grooved & tongued joint 6mm, including fixing with necessary nails, screws etc. complete as per the directed by Engineer-in-Charge.

Providing and fixing glazing in wooden door, window and ventilator shutter and partitions etc. complete with necessary decorative beading made of 1st class Padauk wood / 1st class Teak wood Cat- I (A) with necessary screws etc. complete as per the direction of Engineer-in-Charge.

5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).

Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in- charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately).

Providing and fixing 3 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to roof truss pipes by means of ceiling cleats or tied etc. complete as per direction of Engineer -in-charge.

Providing and fixing 6 mm thick designer cement fibre ceiling board of size 610 x 610 mm of approved quality with nails, screws etc. complete. (frame work to be paid seperately)

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/ 120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)

Providing and fixing wall cabinet of size 2.60 x 0.62 x 1.20 mtr. made up of 1st class Padauk wood / 1st class Teak wood Cat- I (A) planks 25 mm thick interior Horizontal shelves made with an interval of 0.36 mtr. clear to an another shelves, remiaing size top, bottom, sides back side covering with 1st class paduak wood planks 25 mm thick including front opening shutter with neceesary locking arrangement, brass Butt hinges, brass handle, brass tower bolt with necessary screws etc. complete and finished with two coats sanding sealer, 2 coats of NC filler, PU/melamine polish of desired shade with machine spray as per the direction of Engineer-in-charge.

Providing and fixing Armed Chair made up of 25 mm thick 1st class Padauk wood / 1st class Teak wood Cat- I (A) jointed processed as per the specification and finished with two coats of sanding sealer, 2 coats of NC filler & PU/mealamine polish of desired shade with machine spray and by providing cushion of good quality over white wire netted mesh of back and sitting as per the direction of Engineer-in-charge.

Providing & manufacturing Executive office Table (1.80(L) x 0.90(W) x0.75mtr (H) made up of 25 mm thick 1st class Padauk wood / 1st class Teak wood Cat- I (A) with legs of 3" x 2" size jointed processed as per the specification and finished with two coats of sanding sealer, 2 coats of NC filler & PU/melamine polish of desired shade with machine spray, with one side 02 No. small & 01 No. big drawers including necessary fittings such as brass handles, locking arrangement etc. complete as per the direction of Engineer-in-charge.

Providing & supplying superior hardwood Cat-II (A) framed artificial Leather back/vimal cloth or equivalent sofa set of approved design and make.

Single seater Sofa

Three seater Sofa

Providing and supplying centre table (Code : 076) of size 800 x 400 x 444 mm of approved quality or equivalent centre table of approved design and make as decide by the client department.