REPAIR / MAINT TO JOINERY, SANITARY FITTINGS, CHAJJAS, TOILETS, GRIT FINISH AND LEAKAGE / SEEPAGE FOR BLDGS IN GEN ROAD, MAP QTRS IN AB ROAD UNDER GEAWC MHOW.

Amount

Taking down steel / wooden windows / ventilators / chowkhat / frame with shutters exc 1.5 sqm but not exceeding 4 sqm each (without taking off shutters from the frames).

Taking down steel / wooden windows / ventilators / chowkhat / frame with shutters n. exc 1.5 sqm each (without taking off shutters from the frames).

Taking down shutters of any description exc 1sqm but n.exc 2sqm each complete all as specified.

M&L 18 to 20 mm thick machine cut marble in jambs / cills / soffits of door / window / ventilator as in frame work to support for aluminium section and like in cement mortar including pointing in white cement using marble dust (1:2) with admixure of pigment to match with marble shade including backing coat in CM (1:4) (Colour of marble shall be as approved by Eng-in-Charge).

S & F aluminium anodised sections for slidings, windows, ventilators, door partition including facbrication of frame shutters and and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc including all accessories such as glazings clips, and rubber beadings for fixing glass panes ifn frame complete all as specified. Note:(i) Glass panes will measured & paid separately . (ii) Rubber beading will not be weighed and paid seperately.

S&F plain, solid, straight chowkats / frames 2nd class HW wrought, framed rebated on the solid, rounded chamfered, put together with glue pinned at joints.

S&F holdfasts confirming to Fe 410-S or Fe 310-S

M&L preparing surfaces and treating backs of chowkats area tarred exc 0.1 sqm but nexc 0.5 sqm each.

Description same as per Item no. 08.00 but treating small articles such as holdfasts, area not exe 0.1 sqm each

S&F 2nd class hard wood 35 mm thick Plain, framed, panelled shutters of factory made (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats complete all as specified and directed

S & F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

S&F 2nd class hard wood 35mm thick glazed and skelton shutters ( factory made)of open rebated and prepared to recive glass, guaze etc (without sash bar)edges of framing plain chamfered or rouunded fitted with cut and beads for sccuring glass, gauge etc size of shutters as specified in SSR Part-I section & clause 8.20(a)..complete all as specified and directed

S & F in repairs opening solid PVC door frame of size 50mm X 47mm made out of 5mm wood grains printed PVC sheet reinforced with MS square tube and edges painted to match with printed shet all as specified & shown on drawing SSR Part II 2010 complete all as specified and directed.

S & F in repairs factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tube for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width struck in side with solvent cement for stiles and plain colour PVC sheet for top tail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement suppling and fixing the frame at site as in repairs all as per specification & drawings given in SSR 2010 Part II all as specified and directed.

M & L for preparing new wood surface and applying one coate of pink primer and two coate of synthetic enamal paint.

S&F butt hinges 100 mm size stainless steel type B-21.

S&F extruded aluminium alloy handles fabricated types, anodised, each 150 mm long

S&F extruded aluminium alloy handles, fabricated type, anodized of size 100 mm.

S&F aluminium, anodised, barrel tower bolt of extruded section and fixed, 150 mm size

S &F extruded aluminium alloy ,anodised ,sliding door bolt 250 mm in length with hasp , staple (bolt type )and fixing bolts and sliding bolts of extruded sections

S&F extruded aluminium alloy ,anodised ,sliding door bolt 300 mm in length with hasp , staple (bolt type )and fixing bolts and sliding bolts of extruded sections

S & F Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete

Hacking out old broken glass exc 1.5 sqm (any thicknes, size and description) from wooden frames glazed with putty or fixed with beads complete on any storey (G+4) of the bldg all as specified and directed by Engineer-in-Charge.

Description same as per Item no. 23.00 from metal framesincluding punching or drilling out old glazing pins/spring clips complete on any storey (G+4) of the bldg all as specified and directed by Engineer-in-Charge.

S&F 3 mm thick sheet glass, ordinary quality & glazing with oil putty in square n.exc 0.5 sqm each pane

S&F 4 mm thick figured glass, pin head type in square n.exc 0.5 sqm each pane

S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples

S&F Aluminium grill (DG 104) 10mm x 5.2mm thick fixed on aluminium F section of suitable size fixed to aluminium window/ventilator.

S&F framed work such as grills, gratings etc with ends of bar shouldered and/or riveted or forged into pikes, framed guard bars etc confirming to Fe-290, Gde -E-165.

M & L Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

M & L Mild steel, plain, black sheet 1mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required

Taking down cement or cement lime plaster of any description on brick or stone masonry all including raking and joints, backing for key, scrubbing down with water etc and removing rubbish outside MD land.

M&L for rendering 15 mm thick in CM 1:6 on stone masonry surfaces finished even and smooth without using extra cement.

M&L for rendering 15 mm thick in CM 1:4 on stone masonry surfaces.

M&L 5 mm thick rendering in CM (1:3) on concrete surfaces of ceiling including sagol finish and finishing the surface even and smooth without using extra cement.

M&L Preparation of new plasterered surfaces and applying two coats of oil emulsion distemper over chalk whiting on wall surfaces complete including all as specified and directed by EIC.

M&L Preparing newly plastered surface of walls and apply 3 coats of white wash

M&L Preparing newly plastered surface of ceiling and apply 3 coats of white wash

M&L for Preparation of old plastered or unplastered decorated surfaces of walls and applying one coat of white wash complete all as specified and as directed by Engr-in-Charge.

Description same as per Item no. 40.00 but on ceiling complete all as specified and as directed by Engr-in-Charge.

M&L for preparation by rubbing down and stopping of old distempered surface and applying one coat of oil emulsion distemper on wall surfaces complete all as specified and as directed by Engr-in-Charge.

Complete removal of existing treatment and applying two coats of plastic emulsion on wall surface over a chalk whiting etc complete all as specified and as directed by Engr-in-Charge.

Preparation of newly plastered surfaces of walls and applying two coats of cement based paint over a coat of white wash complete.

M&L for preparation of old wall surfaces and applying one coats of coloured acrylic water emulsion paint as per the manufacturer's instructions complete all as specified and as directed.

M&L Preparation of new plasterered surfaces and applying two coats of Acrylic weather proof coat 100 % exterior grade paint over one coat of primer on wall surfaces complete including all as specified and directed by engineer in charge or as per manufacturer instructions.

M&L preparation by rubbing down and stopping of old acrylic weather coat surfaces of external walls and applying one coats of acrylic weather coats 100% exterier grade at any floor complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge.

M&L preparation of new wooden surfaces of any description, over 10 cm in width or girth, applying two coats synthetic enamel paint over a coat of pink primer.

M&L preparing new steel surfaces over 10 cm in width or girth of any description and applying two coat of synthetic enamel paint over a coat of red oxide primer.

M&L preparation of new steel surfaces of any description, over 10 cm in width or girth, and applying two coats of synthetic enamel paint .

Dismantling of stone slab and tiles of any description or thickness in floor apron and vertical surfaces laid bedded,joint and pointed in mortar removing of debris outside MD land

M&L 20 mm thick machine cut granite (any type) bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match with granite stone shade over 15 mm thick screed in CM (1:6) (Colour of granite shall be as approved by Eng-in-Charge).

Rounding to edges of stone slabs one edge such as in steps , cooking platform, other similar situations etc complete

Demolition of cement concrete un-reinforced in any position and paving not exc 15cm thick above or below ground level.

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing) removing servicable tiles to store and rubbish off the premises.

M & L PCC 1:4:8 type D2 (using 40mm graded stone aggregate) 75mm thick as in sub base all as specified.

M&L cement concrete 1:2:4 type B-1 (20mm graded stone aggregate) 40mm thick as in flooring & finishing the surface even and smooth without using extra cement all as specified.

M&L non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but n exc 0.11 sqm in floors etc.set and jointed in neat cement slurry and pointed in coloured cement to match including screed bed 15 mm thick in CM 1:6, complete all as specified. & directed by Eng-in-charge

M&L non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n exc 0.38 sqm in floors etc.set and jointed in neat cement slurry and pointed in coloured cement to match including screed bed 15 mm thick in CM 1:6, complete all as specified. & directed by Eng-in-charge

M&L for Light Shade Vitrified Ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including screed bed 20mm thick in CM 1:6 for laying tiles in floor all as specified and directed by Engr-in-charge.

M&L for Light Shade Vitrified Ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in dado/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including screed bed 15mm thick in CM 1:4 for laying tiles inskirting/dado all as specified and directed by Engr-in-charge.

M&L glazed ceramic coloured designer tiles of size 350 X 250 X 7/450X350X7 mm thick on vertical surfaces such as skirting / dado complete as specified including backing coat 10 mm in CM 1:4. complete all as specified.

S&F 18/19 mm thick prelaminated solid PVC, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps (when open) 30 mm.

S&F in repair sink made of stainless steel 1 mm thick with plugs, washers and wastes, incl fixing cantilever brackets and connecting union to pipe, overall size 495 mm X 420 mm bowl size 410 mm X 330 mm X 160 mm with flush pipe complete

S&F in repair sink with draining board made of stainless steel 1 mm thick with plugs, washers and wastes, incl fixing cantilever brackets and connecting union to pipe, overall size 915 mm X 460 mm bowl size 410 mm X 330 mm X 160 mm with flush pipe complete

S&F in repairs stainless steel plate rack for kitchen of size 31”x36”x10” of Make-Nirali/ Blue Star.

S&F in repairs vitreous china wash down white water closet pan (squatt pattern orrisa pattern complete size 580 x 440mm with integral footrest (excl flushing cistern & flush pipe) incl lime concrete etc complete

S&F in repairs vitreous china wash down white water closet pan (pedastal pattern with 'P' or 'S' trap) including connecting to drain and flushing pipe, antisyphonage pipe incl PVC sheet cover etc complete all as specified and directed.

S&F in repairs plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device.

S&F PVC flushing cistern 10 ltr capacity white with inlet ball valve float flush pipe and handle including brackets and fixed in repair

S&F in repairs flush pipe of polythene of low or high density. 32mm dia

S&F in repairs vitreous china white wash hand basin flat back of size 450 mm X 300 mm including brackets, waste coupling, waste pipe etc complete

S&F in repairs CP pillar taps fancy type , cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'hot or cold' with long scerwed shanks and fly nuts screwed for iron pipe of 15 mm bore dia.

S&F 15mm CP bib tap fancy type cast copper alloy with crutch or buttrefly handfle with screwed down , screwed for iron pipe ,fixed in repairs

S&F 15mm CP stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F in repairs, 15 mm bore stop valve, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions.

S&F in repairs 15 mm bore two way angle cock capstan head cast copper alloy chromium plated screwed down high pressure

S&F in repairs 15mm dia wall mixer, chromium plated, hot and cold with capstan head, screwed down, screwed for iron pipe or for brass ferrule.

S&F in repairs 15mm dia wall mixer, chromium plated with telephonic shower arrangements, screwed down, screwed for iron pipe or for brass ferrule.

S&F 15mm dia Brass CP mixer for WHB for mixing hot & cold water screwed down for iron pipe and fixed

M&L PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement

S&F in repairs PVC cabinet of size 61 cm X 41 cm X 10 cm with 4mm thick front mirror of size 60x40cm & self inside etc

M&L in repairs cast iron Nahani trap 75mm with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4)

S&F in repairs brass CP soap dish fancy type Complete all as specified by Engineer In Charge.

S&F in repairs brass CP toilet paper holder fancy type Complete all as specified by Engineer In Charge.

S&F in repairs Aluminium anodised 20mm dia tubular towel rail of length 450 mm Complete all as specified by Engineer In Charge.

S&F in repairs brackets for aluminium anodised 20mm dia tubular towel rail Complete all as specified by Engineer In Charge.

S&F sheet glass self with thickness of glass exc 6 mm, fancy type, rectangular / circular at one end of plan area exc 0.07 Sqm but n exc 0.20 Sqm all as directed by Eng-in-Charge

S & F CP tube jet spray of 15mm bore 1000mm long with holder Complete all as specified by Engineer In Charge.

Towel Rail 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minumum weight 170 gms)

Towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minumum weight 190 gms)

S&F shower arm 15 mm size, 195mm long with bend of 45 degree with flange of PTMT any colour for (min wt. 40 gms)

Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 90 gms)

S&F PVC connection 15 mm dia and 450 mm long with both end socket fixed in repairs.

Taking up or down 15mm steel tubing and connections including cleaning for refixing or removal to store

S&F 15mm bore GI tubing medium grade with all fittings and fixed to walls Complete all as specified by Engineer In Charge.

Description same as per Item no. 100.00 but refixing old steel tubing Complete all as specified by Engineer In Charge.

Taking up or down 20mm steel tubing and connections including cleaning for refixing or removal to store

S&F 20mm bore GI tubing medium grade with all fittings and fixed to walls Complete all as specified by Engineer In Charge.

Description same as per Item no. 103.00 but refixing old steel tubing Complete all as specified by Engineer In Charge.

Taking up or down 25mm steel tubing and connections including cleaning for refixing or removal to store Complete all as specified by Engineer In Charge.

S&F 25mm bore GI tubing medium grade with all fittings and fixed to walls Complete all as specified by Engineer In Charge.

Description same as per Item no. 106.00 but refixing old steel tubing Complete all as specified by Engineer In Charge.

S & F in repair Wall mounted Closet with including necesarry fitting like anchore bolt seat cover and other connecting gaskits etc.Complete all as specified by Engineer In Charge.

S & F in repair Counter top Wash Hand Basin with including waste coupling and necessary acessories waste pipe etc complete of min size 450 X350X130mm Complete all as specified by Engineer In Charge.

M & L Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings .complete all as specified (Paymentfor providing grooves shall be made separately). Note: Work to be executed up to 7 Story building height.

Forming square grooves in plaster n exc 12mm deep and n exc 15mm on face. Note: for 7 Story building

S & F in repair CP fancy type piller cock WHB hot and cold water single lever basin mixer good quality with necessary coonection etc completed.

S & F in repair Tall body tap piller cock 12" suitable for counter top WHB hot and cold water single lever basin mixer good quality with necessary coonection etc completed.

GIRIRAJ CONSTRUCTION AND TRADERS

Goyal Construction