Upgradation of Gumthala Bhagal road via Guldehra Helwa Seonsar Neemwala road in Distt. Kurukshetra)(PMGSY-III Batch-II, T-02, Block Pehowa)

Amount

Milling of distress bituminous layer upto 20mm depth in single pass with suitable milling machine (capable of milling @200-300 sqm area per Hr.) fitted with loading conveyor for loading the milled material directly on the trucks i/c hauling and stock piling the reclaimed material near the central recycling plant or reclaiming to bring to required as per specification to reuse with the approval of Engineer-in-Charge for safe disposal with all leads and lifts complete in all respects.(N.S) Note- The unutilized quantity of reclaimed bituminous mix material shall be recovery item.

Clearing and Grubbing road land including uprooting vegetation, grass, bushes, shrubs, saplings and trees girth up to 300mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, to all lead and lifts. Including removal and disposal of top organic soil not exceeding 150mm in thickness as per clause no. 201 of MoRD specification Rural roads-2004.

Earth work excavation in ordinary soil exclusive of compensation of earth-earth-work undressed with all lead & lift including breaking of clods. (HSR 6.2a) , and relaying the same for making of berms and side slopes including laying , dressing, watering & rolling as per HSR 6.2 g-i, g iii & g-v -

Preparation of sub-grade including trenching rough dressing of soil, final dressing of earth to given levels and chamber , watering, rolling with road roller and compacting the bed in all respect before laying paving material [confirming to clause 301 of MoRD specification for Rural Roads-2004] Note: - In widening portion sub grade will be prepared with the use of Baby roller (HSR 24.1) or width of excavation should be made sufficient wide to accommodate road roller. Extra width required for compaction of sub grade shall not be paid and its expenditure shall be in incidental to the work.

Preparation of berms including filling of Earth work, excavation and cutting of earth in all kind of soils including dressing the bank, side slope to given levels and templates after breaking of clouds, including the cost of rolling and watering all allowances for labour hardness wetness irrespective of all lead and lift and including Compensation for earth taken from private land, fields etc. and compacted to meet requirement of table 300-2 of MoRT&H specification clause No. 30 and to entire satisfaction of the Engineer of the work confirming to PWD specification No. 6.2 and 6.3 and 3.2 and the other specification 1990 Ist edition. As per X-section. This item also includes E/W if required in sub f=grade for Widening and Shoulder. Earth used for sub grade, shoulder and berms should have minimum CBR 8%. Note:- No earth work will be allowed to be taken from PWD B&R/ROW except for surplus earth after approval from Engineer.

Providing and laying 150 mm thick granular sub base consisting of filter layer confirming to Table 400.1 Grading - I of MoRD specifications, mixing in a mechanical mix plant at OMC, carriage of mix material to the site of work, spreading in uniform layer with motor grader on prepared surface and compacting with vibratory power roller to achieve desired density complete as per clause No. 401 of MoRD specifications-2004. Note: - 1.Only crushed metal material should be used. No local earth sand shall be used. The material finer than 425 micron shall have zero Plasticity Index (PI).

Providing & laying 75/150 mm thick (Compacted) stone metal (G-II) 53mm to 22.4mm gauge wearing coat to water bound macadam in layer of 75mm each using screening type ‘B’ compacting with three wheeled power rollers of 80-100 kN capacity or tandem or vibratory of 80-100 kN static weigth to achieve the desire density including lighting, guarding barricading and maintenance of diversion etc. as per clause no 405 of MoRD specification for Rural Roads-2004) as per drawing and design directed by the Engineer complete in all respects.(N.S.) Note: - 1.Only crushed stone metal material should be used. No local earth/ natural occurring sand shall be used. The material finer than 425 micron shall have zero Plasticity Index (PI). 2. Materials to be used and operations of manufacturing shall be approved by engineer.

Providing and applying primer coat with bitumen emulsion (SS-I) on prepared surface of granular base including cleaning of road surface and spraying primer mix including silane at the rate of 0.70 kg/sqm using mechanical means as per Technical specification clause 502 of MoRD specification Rural roads-2004. Instructions issued from time to time by MoRD regarding bitumen emulsion will be followed strictly. Note:- Bituminous Macadam to be laid with in 24 Hrs. of laying primer coat & Tack coat does not required to be provided above the primer coat. However, if the BM is not laid with in 24 hours of laying prime coat then tack coat would have to be provided by the contractor but no payment at the same shall be made and it would be incidental to work.

Providing and applying Tack coat of VG 10 ( 80/100 grade) bitumen using bitumen @ 0.25 kg per sqm including clearing and blowing dust off the surface using a compressor and brooms ( conforming to clause 503 of MoRD specification-2004) for PC. Instructions issued from time to time by MoRD regarding bitumen VG-10 will be followed strictly.

Pdg& laying 50mm BM using the reclaimed material to the extent of 30% of the required quantity, hauling and stockpiling the reclaimed material near the central recycling plant after carrying out necessary checks and evaluation, adding fresh material including rejuvenators as required, mixing in 100-120 TPH batch type hot mix plant, with appropriate arrangement for use of R.A.P., transporting and laying at site with hydraulic paver finisher with sensor control to the required grade and compacting to the required grade level and thickness with appropriate rollers all as specified in clause 519 (5th Revision) of 2013 using bitumen VG-30. (minimum Bitumen's 3.40% i/c bitumen of retrieved material as per job mix formula) complete in all respect. Note: -1. The milled material to be used in BM shall be minimum 80% of the theoretical quantity of milled material. 2. If bitumen required more than 3.40% as per job mix formula no extra payment will be paid extra bitumen required will be considered as incidental to work. 3. Before carrying out bituminous work, coating & Stripping of bitumen aggregate mix is to be performed in accordance with IS-6241. If coating and stripping of bitumen aggregate mix is less than 95%, anti-stripping agent will be used by contractor. The anti-stripping agent should conform to the requirement as stipulated in IS 14982:2017. The cost so incurred will be considered as incidental to work and noting extra shall be payable. The type and brand of anti-stripping agent along with procedure shall be approved by SE-in-Charge in writing before start of work. A proper record of results be maintained and same shall be submitted along with bills by the contractor. Note:- Where there is BM on existing black top, cracks shall be sealed as MoRT&H specification 5th revision clause No. 3004.3, which may consists of (i) fog seal /or (ii) crack filling and or (iii) patch work repair as required at site in accordance with clause No.3004.3.2,3004.3.3 and 3004.2 of MoRT&H specification 5th revision respectively. Proper measurement and consumption shall be entered in MB for cracks sealed but no payment on this account shall be made as crack filling is incidental to work.

Providing laying and rolling of open graded pre mix carpet (PC) of 20mm thickness composed of 13.2 to 5.6 aggregates using bitumen VG-10 @1.36 kg per sqm. (93% bitumen) and processed @ 0.10 Kg/Sqm (waste plastic 7%) as per IRC SP -98 -2013 to required line , grade and level to serve as wearing course on previously prepared base , including mixing in a suitable plant, transported to site , laying with paver finisher and rolling with three wheeled 80-100 kn static roller capacity or with other approved equipment, finished to required level and grades as per MoRD specification clause 508. NOTE- Before carrying out bituminous work, coating & Stripping of bitumen aggregate mix is to be performed in accordance with IS-6241. If coating and stripping of bitumen aggregate mix is less than 95%, anti-stripping agent will be used by contractor. The anti-stripping agent should conform to the requirement as stipulated in IS 14982:2017. The cost so incurred will be considered as incidental to work and noting extra shall be payable. The type and brand of anti-stripping agent along with procedure shall be approved by SE-in-Charge in writing before start of work. A proper record of results be maintained and same shall be submitted along with bills by the contractor.

Providing and laying ‘B’ type seal coat with VG-10 grade bitumen @ 0.68 kg per sqm of road excluding cost of tack coat, with mixed material brought from Hot mix plant and laying with paver finisher and compacting with road roller to achieve specified/desirable value of compaction as per direction of Engineer including cost of lighting arrangement, sign board and night watch, complete in all respect as per clause 510 of MoRD specification for rural roads 2004.

Manufacturing, laying of table vibrator cement concrete blocks of size 0.450mm X0.300mm X 0.150mm of cement concrete(C.C) M-30 grade and spreading 25mm thick sand under neath and filling joints with sand on existing base as per Technical specification Clause 1503 of MoRD specification for Rural roads 2004.

Dismantling of existing CC block pavement including transporting and stacking usable block along road side and dispose unusable blocks outside PWD land or desired by Engineer (NS)

Relaying of existing of C.C. Blocks over 25mm thick sand under neath and filling joints with sand on existing base as per Technical specification Clause 1503 of MoRD specification for Rural roads 2004.

Providing Reinforced cement concrete M-15 grade 5th km stone of standard design as per IRC-8 fixing in position including painting and printing etc as per drawing and technical specification clause 1703 of MoRD specification clause for rural roads-2004.

Providing kilometer stone made of concrete as per specified design conforming to MoRD specification No. 1703, all inclusive, including cost of concrete, fixing, painting writing etc. ( conforming to MoRD specifications for Rural Roads-2004).

Providing and fixing 200 m stone made of concrete as per specified design conforming to MoRD specification no. 1703; all inclusive, including cost of concrete, fixing, painting, writing etc. ( conforming to MoRD specifications for Rural Roads-2004).

Reinforced cement concrete M15 grade boundary pillars/local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704

Providing and fixing of typical PMGSY informatory sign board with logo as per MoRD specification and drawing.Three MS plates of 1.6mm thick, top and middle plate duly welded with S flat iron 25mmX5mm size on back on edges,25mmX25mmX5mm. The angle iron frame of the lower most plate and flat iron frme of middle plate will be welded to 2 nos,.75mmX75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mmX450mmX600mm below ground level. The top most diamond plate will be welded to middle plate by 47mmX47mm of 12 SWG steel plate tube . All MS will be stove enamelded on both sides. Lettering and printing arrows, border etc. will painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.0.

Providing & erecting OVERHEAD SIGNS gantry supported by M. S. Pipe Structure complete as per drawings, Technical Specifications and as directed by Engineer-In-Charge including construction of R.C. C. foundation for providing of M. S Tubular structure for Cantilever signage at given site as per drawing enclosed. The C. C. mix to be in ratio of 1:1½:3 (RCC 1:1½:3) and that of lean to be ratio of 1:3:6 the work will be carried out as per the instructions of Engineer-In-Charge. Note: Foundation including reinforcement etc. as per Drawing. Cantilever Over head Sign gantry. frame/truss Size- 3.05 m x 1.525 m

Providing and fixing of shoulder mounted sign boards of various sizes using non-metallic micro prismatic retroreflective sheet conforming to IRC: 67 -2012 type lV HIP specification fixed on 3 mm thick Aluminium anel,having 0.5 mm thick Composite Aluminium on both sides supported on Mild Steel Pipe leg post 80mmNB,1.6mm thick duly painted in alternative color of black and white embeded M-20 Grade concrete foundation of size 450mm x 450mm x 600mm, complete as per drawings, Technical Specifications and as directed by Engineer-in-Charge - 600 mm equilateral triangle

600 mmcircular

600 mm x 450 mm rectangular

900 mm side octagon

Providing & Marking center line / side line 2.5mm thick (minimum) with hot applied thermo-plastic road marking paint 10cms wide complete in all respect such as furnishing all labour, materials, tolls equipments including all incidental costs necessary for carrying out in work at site confirming to the technical specification as clause No. 1702 of MoRD specification . Each container of the thermoplastic material shall have the name trademark or other means of identification of manufacturer, batch number, date of manufacture color maximum application temperature and maximum heating temperature. The thermoplastic paint material shall be of Asian Paint-Apcomark/Berger-Sigmarc/Prismo. The glass beads shall be of Potters/Sovitec/Fleolite. The thermoplastic material shall be sampled and tested in accordance with appropriate ASTM/BS method. The contractor shall furnish to the Engineer-in-Charge a copy of certified test reports from the manufacturer of the thermoplastic material meet all requirement of the specifications. The reflectorzing glass beads shall meet the requirement of clause 803.4.2 and test methods mentioned in clause 803.4.2.4 shall be meticulously followed. The minimum thickness specified is exclusive of surface of glass beads .the method of thickness measurement shall be in accordance with appendix B and C of BS:3262 (part-3). Note:- Before start of work the contractor shall give brand , batch no. , manufacturing date of the material to be used and get approved the same from Engineer-In-Charge before use. Edge Line @20%

Pavement marker (Cat eyes)Molded shank raised pavement marker made polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a lad of 16000 Kg tested in accordance to ASTM D 4280 Type H. The height, width and length shall not exceed 50mm and 100mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall 35+/-5 degree.The strength of detachment of the intrgratedcyclindrical shanks(of diameter not less than 19+/-2mm and height no less than 30+/-2mm) from the body is to be a minimum value of 500 kg .Fixing will be bt drilling without nails and using epoxy resin based adhesive as per manufacturer’s recommendation(of reputed make such as 3M etc.)

Providingand fixing retroeflective hazard marker confirming to IRC 79:1981 of size 900x300 mm with back support of M S angle 25*5x3 mm and leg postof80mm dia having 1.6mm thickness dulypainted,1500 mm high embedded into 0.3x0.3x0.45m M20 gradeConcreteaspersite requirements, micro- usingnon-metallic prismaticretro-reflectivesheet confirming to IRC: 6720'12 type lY specificationfixed on 3 mm thick aluminum composite Material sheete as base having 0.5 mm thick aluminumon both sides.

Earth work in excavation in foundations, trenches, etc. in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres (HSR 6.6)

Design mix cement concrete of grade M-10 with minimum cement contents 220 Kg./cum in foundation and plinth. (HSR 10.63)

Providing & laying in position machine batched and machine mixed design mix M-15 grade cement concrete for plain cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge in foundation and plinth. (Note: Cement content considered in this item is @ 240 kg/cum.). (HSR 10.64)

Providing & laying in position machine batched and machine mixed design mix M-20 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge in foundation and plinth. (Note: Cement content considered in this item is @ 300 kg/cum.). (HSR 10.65)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge in first storey upto 4 meters above plinth level. (Note: Cement content considered in this item is @ 330 kg/cum.). (HSR 10.66)

Steel reinforcement TMT bars FE-500 EQR / FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights / depths / storeys / basements etc. Note: Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement.

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces. (HSR 16.25) + Painting two coats with ready-mixed exterior paint in all shades on newly plastered or concrete surface of walls. (HSR 16.25+16.26)

First class brick work laid in cement sand mortar 1:3 in foundation and plinth (HSR 11.5)

12 mm thick Plastering with cement mortar (1:3 ) (HSR 15.4)

Providing, lowering, cutting, jointing and testing 600mm dia RCC pipe Class NP-3 as per IS 458-2003 with Spigot and socketed joints manufactured with ISI marked Sulphate Resistance Cement as per ISI 12330 with rubber rings ISI marked , antitermite as required at site , into trenches, for all depths and laying out the same to correct alignments, gradients and levels including dressing and trimming and cutting of concrete beds and sides of trenches , if required , Jointing with rubber rings in trenches and jointing with 1:1 ½ cement sand mortar and with end dowels filled with 1:1 ½ cement sand mortar and finishing the joints at angle of 45 degree with faces of spigot of socket joints cutting and finishing the cut surface to a uniform finish etc. as fully described in (HSR item No 29.38,29.44,29.45 & 29.46) including cartage , loading and unloading complete in all respects. (HSR 29.96)

Recovery items: The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer and granular layers have been calculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specifications) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the price quoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned as under :- Bitummenous Mix Material @ Rs. 1667.81/- P. Cum

AJIT CONSTRUCTION CO