Special Repair of bldg No P51 at NAI under GE Gomantak

Amount

Taking down cement plaster on brick work or stone walls or roof slab including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for cleaning of roof tops including removing the existing treatment by brooming down with steel wire brushing scrapping down with steel scrapper and roughening the existing surfaces to receive plaster complete all as specified and as directed by Engineer-in-Charge. Note: The debris out the cleaning/removing/ scraping shall be removed out MD Land complete all as specified and as directed.

Demolition of concrete of any description complete all as specified and directed by engineer in charge.

M&L for 25mm thick Cement concrete (1:2:4) type B0 (using 12.5mm graded aggregate) as in levelling course of slab all as specified and as directed by Engr - In - Charge.

M&L for providing 10mm thick cement plaster over roof slab (over the area of dismantled roof treatment ) in cement mortar 1:3 finished even and smooth without using extra cement with WPC complete all as specified and as directed. Note:WPC shall be measured and paid separately)

Supply & Laying water proofing treatment using 4mm thick APP modified membrane and as per manufacturers instructions with features as specified , weighing not less than 4.0 kg per Sqm laid over a coat of cold applied bituminous primer @ 0.20 Kg per sqm by torching the membrane including sealing the overlap while torching with 100mm on length side and 100mm wide side as per manufacturer instructions including joints and changes in direction the curved with cement mortar 1:3 mixed with SBR latex @ 200 Ml/bag of cement cured well before laying of membrane all as per manufacturer instructions and to the satisfaction of Engineer -in-charge including two coats of bituminous aluminium paint all as specified and directed. Note (i) irrespective of lap the net covered area will only be measured for payment. (ii) The quoted rate is deemed to be inclusive of primer APP membrane & SBR Latex. (iii) The contractor shall carry out water proofing work with authorised applicator only.

M&L for rendering in cement mortar 1 : 6 ,10 mm thickness on brick/cement/stone surfaces and finishes the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 3mm thick Birla white wall care putty on wall including preparation of new surfaces with necessary sand paper for applying two coats of distemper oil emlusion over a coat of alkali resistant primer complete all as specified and directed.

M&L for complete removal of existing treatment and applying 3mm thick Birla white wall care putty on wall and applying two coats of distemper oil emlusion over a coat of alkali resistant primer including preparation of old surfaces of wall complete all as specified and directed.

M & L for rendering 5mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 in ceiling complete all as specified and as directed.

M&L for providing three coats of white wash on new plastered ceiling surfaces including necessary preparation to surfaces complete all as specified and as directed.

M&L complete removal of existing treatment and providing three coats of of white wash on old plastered ceiling surfaces including necessary preparation to surfaces complete all as specified and as directed.

M&L for rendering in cement mortar 1 : 4 (10+5)=15mm thickness on brick/cement/stone surfaces and finishes the surface even and smooth without using extra cement including mixing with liquid WPC on top 5mm thick only complete all as specified and as directed. Note :- Water proofing compound will be paid separately

Supply only liquid water proofing compound.

M&L for applying two coat of acrylic emulsion exterior paint (anti fungal paint) over a coat of acrylic emulsion primer on new surface including preparation of surface of any description all as specified and directed by Engr-in-charge.

M&L for complete removal of existing treatment and applying two coat of acrylic emulsion exterior paint (anti fungal paint) on old plastered surfaces walls and corniers incl preparation of surfaces by brooming down or steel wire brushing scrapping down with steel scrapper smoke soot moulds moss and efflorescent slats brading oil and greasy spots etc and making proper surface by applying ready mix preparatory putty wherever required complete all as manufactorers instructions (manufactored by : asian paint apex ultima)

Dismantling boarding, any description, fixed in any position with nails as specified and as directed.

S&F 605x605 mm anodised aluminium snap grid frame work for false ceiling all as specified including hangers 6 mm dia. G.I. Wire (upto 1200mm to 2000 mm length) adjusting level fixed to roof with steel members as directed by engr-in-charge

M&L PVC insulation panels with EPS stuck to 10mm plain PVC sheet suitably placed in false ceiling grid made of aluminium /G.I./M.S as per specification and drawing as directed by engr-in-charge

S&F solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet used instead of plain colour sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing as directed by engr-in-charge. make : Rajshree or eqlt.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing as directed by engr-in-charge.make : Rajshree or eqlt.

Dismantling kitchen and bathroom floor, hearth or wall tiling including cement mortar bedding (including backing) and rubbish off the premises complete all as specified and as directed.

M&L 40mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in flooring rough finished.

Material and labour for glazed ceramic coloured tiles of size 450X 350X 7mm thick as on vertical surfaces, set and jointed in neat cement slurry and pointed in white cement with pigment to match with the shade of tiles laid over and including 10mm thick screed backing layer in CM (1:3) complete all as specified and as directed.

Material and labour coloured non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15mm thick screed bed of CM 1:6, complete all as specified and directed by Engineer-in-charge.

Material and labour for non skid ceramic coloured tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm coloured in floor etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 15mm thick screed bed in CM (1:4) complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including screed bed of 20 mm thick in CM 1:3 all as directed.

M&L for machine cut kota stone slab 20-25mm thick in riser of steps, skirting, etc over & including 10 mm thick rendering (bedding layer) in CM 1:3,laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mmirror finished complete.

M&L for vitrified ceramic tiles light shed 10 mm thick (square/rectangular) polished area of each tiles not exceeding 0.36 sqm but in floors etc set & jointed in neat cement slurry & pointed in white or coloured cement with pigment to match including 15 mm thick screed bed (1:4) in cement mortar complete all as specified and as directed.

M&L for granite (of any type) 20 mm thick work (table rubbed and polished) in steps, jambs, pillars, skirting,window cills, cooking platforms, urinal partition etc and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade complete over and including screed bed or bedding layer of mortar 15 mm thick in CM 1:3 for laying floor finishes all as specified and as directed.

M&L for granite (of any type) 20 mm thick work (table rubbed and polished) as in flooring etc and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade complete over and including screed bed or bedding layer of mortar 15 mm thick in CM 1:3 for laying floor finishes all as specified and as directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) pedestal pan and trap including connection to drain and to flushing pipe ,antisyphonage pipe , plastic water closet seat,black ,closed pattern with flat bottom ,cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed.

S&F in repairs PVC valveless, symphonic action type, flushing cistern, 10 liters, low level, white, with inlet, ball valve, float and handle including brackets and connections to pipes and fixing of chain and pull, or level, if any fixed in repairs including flush pipe complete all as specified and as directed.

S&F in repairs white colour vitreous china urinals, bowl type (back or corner wall type ), complete including oroviding and fixing plugs,bedding urinal against wall in cm 1:2 securing urinal to plugs with and including 60 mm long brass screws,pointing around urinal back in cm ,fixing automatic flushing cistern with brackets , flush pipe,grating and union for discharge pipe to flushing cistern,trap and waste pipe; half stall type

S&F in repairs Stainless steel soap dish standard size heavy complete all as specified and as directed.

M&L for 100 mm dia PVC(SWR) floor trap, with plain grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

S&F in repairs flush pipe of polyethylene of low or high density or PVC 32 mm dia for low level cistern complete all as specified and as directed.

S&F in repairs vitreous china wash basin, white, ovel shaped back, size 630x450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, waste pipe & 32mm dia CP grating complete all as specified and as directed.

S&F in repairs pillar taps, 15mm dia, cast copper alloy, fancy type with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in repairs complete all as specified and as directed.

S&F in repairs concealed CP stop cock/angle cock 15mm dia, fancy type with capstone heads screwed both ends for iron pipe or for unions and fixed in repair complete all as specified and as directed.

S&F in repairs angle cock 15mm dia, fancy type with capstone heads screwed both ends for iron pipe or for unions and fixed in repair complete all as specified and as directed.

S&F in repairs bib taps, 15mm dia, cast copper alloy, fancy type, with capstone head, screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs complete all as specified and as directed.

S&F Swivel shower of C P Brass any colour for fixing with 15mm pipe .(Minimum weight 40gms) fixed in repair complete all as specified and as directed.

S&F Shower arm 15mm size,195mm long with bend of 45degree with flange of CP brass any colour. (Minimum weight 40gms) fixed in repair complete all as specified and as directed.

S&F in repairs Towel Rail 600mm long of CP brass fixed with and including Chromium plated brass screws and wooden/plastic cleats .(Minimum weight 190gms) fixed in repair complete all as specified and as directed.

S&F PVC connections 15 mm size with PTMT nuts of length 600mm fixed in repair complete all as specified and as directed.

S&F in repairs health facet with 1 metre (min) extendable metal tube and holder and fittings of make "Jaguar" complete all as specified

Taking down 20 mm steel tubing and connections, including cleaning for refixing or removal to store etc as directed.

Taking down 25 mm steel tubing and connections, including cleaning for refixing or removal to store etc as directed.

Supplying and laying of 20 mm CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 25 mm CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) n.exc 1.50 sqm each complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) .exc 1.50 sqm but n exc 4 sqm each complete all as specified and as directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S&F Factory Made Solid PVC Moulded Door Shutter with particle board core, 2 mm thick moulded prelam PVC Sheet on the front face & 2 mm prelam PVC sheet on back face, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing

S&F 2nd class hard wood plain solid straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S&F 35mm thick factory made 2nd class hard wood rail and style Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated

M&L preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel over coat of pink primer

M&L for PCC type C1 1:3:6 (using 20 mm graded aggregate) for filling the holes of the hold fasts.

S& F MS flat iron 25 x 3 mm as in hold fast for fixing if chowkats.

S & F Butt hinges, 100 mm cast brass,with mild steel hinge pin, bright polished and fixed, typeB-11

S & F extruded aluminium alloy handles fabricated 'D' type of size 150 mm.

S&F 300 mm long aluminium alloy anodized, sliding bolt with hasp,staple (bolt type) and fixing clips of sheet, cost or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S&F aluminium anodized barrel tower bolt of 150mm long of extruded section.

S&F Steel rolling shutters, with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer;erected in position as indicated,complete: push pull or manual type thickness of lathe 1.00mm incl taking down old rolling shutter and two numbers safety lever locks mild steel with 4 levers for each rolling shutter complete all as specfified and directed.

M&L preparation and applying two coat of aluminium paint on new steel surface of any description, not otherwise, described, over 10cm width or girth over a coat of aluminium red oxide for rolling shutter.

S&F PVC (SWR) 75 mm dia pipe in repair for roof drain pipe and fixed to wall with bracket including proper packing with CM 1:3

S & F powder coated (50 micron) window or ventilator shutter and frame any type (slidding or openable) with frame or other similar work etc section fabricated by using the JINDAL/ INDAL /HINDALCO /sections including necessary roller,wheel cleat handals locking arrangements also to receive 4.8mm thick glass with aluminum chanel beading and stainless steel scrw including and rubber gasket beading etc complete (the weight of rubber gasket beading will not be measured with the weight of aluminum shuter glass will be measured and paid separately)All scections as approved by GE

S&F Aluminum powder coated deco grill make DG 104 (10 mm thick section) with frame of section not less than 0.136 kg/rm complete all as specified and as directed.

S&F 4.8mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and as directed.

S&F solar control film 25 micron reflective type (gareware sun control or equivalent)

S&F in repair Aluminium powder colour coated door frame and shutter single or double leaf glaszed/prelaminated board partly glazed. Panels fabricated including aluminium anodised frame tinted glass 5.5mm thick. The door frame should be fixed with aluminium anodised beading rubber and packing material and shall be drilled in existing wall and thurst bolt suitable saizeas all as spd. The door frame and shutter shallbe made as under:-(a) Aluminium colour coated door frame of section 100 x 44 x 2mm (b) Aluminium colour coated bottom rails of shutter section 200 x 44 x 2mm (c Aluminium colour coated top , middle/lock rail of shutter section 150x44x2mm. (d) Six lever mortice lock brass Make: GODREJ/ARGENT 01 each door (e) Aluminium colour coated tower bolt 200mm long 02 Nos each door (f) Aluminium colour coated handle 150mm long 2 nos (g) Heavy duty door machine ISI marked or equivalent as approved (h) Tinted glass 5.5 mm thick . Make : MODI/SWASTIC (J) 12mm thick both faces prelaminated board. Aluminium Make: Jindal or eqlt.

S&F in repairs door closer hydraulically regulated designation no. 3 universal type suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed aluminium body type as specified and as directed.

S&F floor door stopper of 150mm cover plate, aluminium alloy body and tongue, anodised, with hard drawn steel spring as specified and as directed.

S&F for 12mm thick toughened glass door along with necessary articles, joining and locking accessories and complete fittings for door all as specified and directed..

S&F for roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings, MS pipe for post and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc (Fe- 290 (Gde E- 165).

M&L for Painting with two coats of synthetic enamel paint over red oxide priming Surfaces of any description, over 10cm in width or girth,not otherwise described including preparation of surface

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings. Etc

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc as directed.

S&F for Collapsible steel gates/rolling shutter 1.25 mm thick (gear operated), top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, including two coats of synthetic enamel paint over a coat of red oxide primer complete including taking down old steel gate.

Dismantling stone slabs in floors any thickness, jointed in any mortar complete as directed and specified

M&L 80 mm thickness machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of ] M-40 Grade fined with grey cement and no pigment complete all as specified.

M&L 100 mm thick PCC type D-2 (1:4:8) using 40 mm graded stone aggregate as in sub base all as specified and directed by engr-in-charge.

M&L for sand cushioning under floors in foundation including watering and consolidation all as specified

M&L hardcore broken stone or boulders of gauge exc. 63 mm but n exc 100 mm,deposited,spread and levelled In layers n exc. 15 cm thick,watered and rolled/rammed to true surface.

Taking down carefully copper/aluminium point wiring (light, fan socket or power) complete including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing material to store for keeping in safe custody or for taking credit ( credit for above items should be made as per condition seperately) and making good disturbed surface of walls, floors etc complete all as per the existing finish.

Material and labour for point wiring with 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20mm dia or higher, medium grade complete with and including all PVC conduit and accessories concealed into wall by cutting of chases in wall/ceiling and replacement of modular metal flush box, modular white cover plate with frame, blanking plate etc suitable for Mylinc / Coral / Sleek model accessories etc and making good to the disturbed surfaces to match the existing complete all as specified and directed for one the following:-

(a) One light/fan/exhaust fan point controlled by one switch.

(b) One light point controlled by two Nos two way switches.

(c) One 5 pin switch socket outlet 5 Amps on same board controlled by one switch.

(d) One 5 pin switch socket outlet 5 Amps on independent board controlled by one switch.

All as per item No 2 here-in-before but for 2 in 1 three pin socket outlet 15/20 Amps on independent board with 4 Sqmm cable FRLS copper conductor multistranded including 4 sqmm PVC insulated and unsheathed FRLS copper conductor cable as earth continuity wire all as specified and directed by Engr-in-Charge.

Supply and fix modular switch, one way 6 Amp ,1 module

Supply and fix modular switch, two way 6 Amp ,1 module

Supply and fix modular switch, one way 16 Amp ,1 module

Supply and fix modular socket 6 Amp, 2 / 3 pin, 1 module

Supply and fix modular socket 6/16 Amps, 2/ 3 pin 2 module

Supply and fix ceiling rose, surface bakelite, 65x50 mm, two to three terminals complete.

Supply and fix modular fan regulator flush type complete as diricted.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1400 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply & fixing exhaust fan (Plastic body) 300mm sweep, heavy duty, 230 volts ,1400 RPM including louvers of suitable size and making hole size as per requirement , dismantling of old one depositing in MES store yard as per specified and directed by Engr-in-Charge. Make : Orient/Havells/Bajaj

Supply and fixing LED tube light fitting surface and wall mounted batten with 20 watts LED having minimum 100 lumens/watts and with integrated electronic driver complete made up of polycarbonate complete all as specified and directed.

Supply and fixing LED mirror type light fitting surface and wall mounted batten with two feet 10 watts LED having minimum 100 lumens/watts and with integrated electronic driver complete made up of polycarbonate complete all as specified and directed.

Supply & Fixing Recess mounting LED fittings 36 watts , suitable for 600 mm x 600 mm (2ftx2ft) modular/POP/Gypsum ceiling, luminaire with white powder coated CRCA housing with LEDs. seamless front frame with fat white high transmission acrylic cover 230V, complete in all respect & accessories internally prewired including connecting up with twin copper twisted flexible copper conductor cable with suitable size incl taking down old fitting of any type. Bajaj/Havells/Wipro/Philips.

Supply & fixing wall mount fan 450mm sweep (air Circulator) (ISI marked) 230 volts all as specified and directed by Engr-in-Charge. Make : Usha/Havells/Bajaj

Supply and fix in replacement of sheet metal enclosure (DB) for MCB's, 8 way, single pole and neutral, 240 volts, double door complete.Make : Legrand /C&S/Havells

Supply and fix in replacement of sheet metal enclosure single pole and neutral with a two pin and earth plug and socket complete with and including one single pole MCB 20 Amps,C series 240 Volts complete.

Supply and fix in replacement of MCB, single pole,16 Amp to 32 Amp, 240 Volts, 'C' Curve 10KA. Make: Legrand /C&S/Schneider /Havells/L&T

Supply and fix in replacement of MCB, single pole neutral (SPN) , 40 Amp, 240 Volts, 'C' Curve 10 KA. Make:Legrand /C&S/Schneider /Havells/L&T

Material and Labour in replacement of sub main wiring with single core, PVC insulated unsheathed cables two run of 2.5 Sq mm multi stranded copper conductor drawn through and including 25 mm wide non metallic PVC conduit incl all accessories fixed on walls/roof/floors/ceiling etc with an earth wire of one run 2.5 sqmm copper wire earth continuity conductor connecting to existing main switch board \ Distribution Board and testing on completion etc including taking down old submain wiring of any type with conduit/cpaing casing and making good disturbed surfaces to match existing all as specified and directed. Note : Three runs of 2.5 sqmm cable and one run of PVC Caping casing not less than 25mm width shall be measured as one run.

Material and Labour in replacement of sub main wiring with single core, PVC insulated unsheathed cables two run of 4 Sq mm multi stranded copper conductor drawn through and including 25/32mm mm wide non metallic PVC conduit incl all accessories fixed on walls/roof/floors/ceiling etc with an earth wire of one run 4 sqmm copper wire earth continuity conductor connecting to existing main switch board \ Distribution Board and testing on completion etc including taking down old submain wiring of any type with conduit/cpaing casing and making good disturbed surfaces to match existing all as specified and directed. Note : Three runs of 4 sqmm cable and one run of PVC Caping casing 25/32mm width shall be measured as one run.

Material and Labour in replacement of sub main wiring with single core, PVC insulated unsheathed cables two run of 10 Sq mm multi stranded copper conductor drawn through and including 25/32mm mm wide non metallic PVC conduit incl all accessories fixed on walls/roof/floors/ceiling etc with an earth wire of one run 10 sqmm copper wire earth continuity conductor connecting to existing main switch board \ Distribution Board and testing on completion etc including taking down old submain wiring of any type with conduit/cpaing casing and making good disturbed surfaces to match existing all as specified and directed. Note : Three runs of 4 sqmm cable and one run of PVC Caping casing 25/32mm width shall be measured as one run.

Taking down Split type AC of any capacity and kept in safe custody/ deposit MES Store till the completion of Bldg Work and refixing the same after servicing and gas filling complete all as specified.

JINTECH

M/S DUBAL CONSTRUCTION

M/S Kartik Enterprises

K M SUBHANAIAH

Shine Enterprises

M/S jvsr constructions

M/S P S BABU

STAR FABRICATION

SACHIN CONSTRUCTIONS