Infrastructure for the 1000 LPM Oxygen Generation Plant for COVID Patients at MCH Building, Lakhimpur Medical College Campus, North Lakhimpur (Assam).

Amount

CIVIL WORKS:- Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared. sqm 7.40

Earth work in excavation by mechanical means (Hydraulic excavator) manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing andreinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 18 mm thick

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately). 0.56 mm, Aluminium Color coated troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface Water thinnable cement primer

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

ELECTRICAL WORKS:- Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required 200 mm dia (OD-200 mm & ID-175 mm nominal)

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 250 A, 25 KA, TPMCCB

250 A, 36KA, FPMCCB

400 A, 50KA, FPMCCB

Supplying including installation, testing and commissioning of 250 KVA Water cool, 3 Phase, 50 hz, Diesel Generator set, Engine will comply with present CPCB-II norms, Alternator is suitable for continuous operation rated at 1500 rpm 415 V, 0.8 PF, 50 Hz, 3 Ph. In SPDP enclosure, self-excited & self-regulated, Brush less, floor mounted with Ball or Bearings on end shields. The alternator efficiency is as per IS 4722 & IEC 34-1 standards & will be suitable for tropical condition, with AMF Panel, Battery, DG set Canopy, Exhaust Silencer, Fuel tank etc. Make: Kirolskar (Koel Green)

Supply of following size of PVC/ XLPE insulated and PVC Sheated 1.1 KV gd Solid aluminum conductor upto 10 sqm, blance stranded conductor, XLPE insulated, cores laid up, PVC tale innersheathed, armour (Aluminium wire for single core up to 70 sqm, balance aluminium strip, galvanized wire for cables upto 2x10 sqm, 3x10 sqm, 4x6 sqm & balance all galvanized steel strip), extruded PVC type ST2 sheathed, 650/1100V grade as per IS 7908 (part-1) 1988 armoured U.G cable as specified and directed by the department. ( Havells/ RR cables/ Polycab or equivalent make as approved by this deptt.) 300.00 sqm 3.5 core armoured UG cable.

Supply of following size of PVC/ XLPE insulated and PVC Sheated 1.1 KV gd Solid aluminum conductor upto 10 sqm, blance stranded conductor, XLPE insulated, cores laid up, PVC tale innersheathed, armour (Aluminium wire for single core up to 70 sqm, balance aluminium strip, galvanized wire for cables upto 2x10 sqm, 3x10 sqm, 4x6 sqm & balance all galvanized steel strip), extruded PVC type ST2 sheathed, 650/1100V grade as per IS 7908 (part-1) 1988 armoured U.G cable as specified and directed by the department. ( Havells/ RR cables/ Polycab or equivalent make as approved by this deptt.) 185.00 sqm 3.5 core armoured UG cable.

MEDICAL GAS PIPELINE SYSTEM WORKS:- MEDICAL OXYGEN SYSTEM:- Supply, installation, testing & commissioning of Oxygen Manifold with 8 Nos. pigtailpipes for 4+4 cylinders and Non-returnvalves, as per enclosed technical specifications and approved make (without cylinders)

Supply, installation, testing & commissioning of Fully Automatic Oxygen Contr0l Panel, as per HTM-2022/02-01ofUK/NFPA99C of USA as per enclosed technical specifications and approved make

Supply, installation, testing & commissioning of Oxygen Manifold Emergency for 2 Cylinders, as per enclosed technical specifications and approved make- (without cylinder)

Supply, installation, testing & commissioning of Oxygen Outlets with matching probes, CE certified with four digit notafied number as per enclosed technical specifications and approved make- (Imported)

Supply, installation, testing & commissioning of Oxygen Flowmeter with Humidfier Bottle CE Certified with four digit notafied number /UL Listed,as per enclosed technical specifications and approved make - (Imported) for critical area

Supply, installation, testing & commissioning of MEDICAL Grade BS EN: 13348 Kite Marked COPPER PIPE 12mm

Supply, installation, testing & commissioning of MEDICAL Grade BS EN: 13348 Lloyd Marked COPPER PIPE 15mm

Supply, installation, testing & commissioning of MEDICAL Grade BS EN: 13348 Lloyd Marked COPPER PIPE 22mm

Supply, installation, testing & commissioning of MEDICAL Grade BS EN: 13348 Lloyd Marked COPPER PIPE 28mm

MP AGARWALA PVT.LTD