Loading
Loading…
Loading…
Tender Value
₹1.3 Cr
EMD Value
₹2.5 L
Closing Date
7 Sept 2026, 11:00 am
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
45 days
Expenditure
Capital (Works)
DEN/C
25 conditions · 4 needing a document upload
No Technical and Financial credentials are required for tenders having value up to Rs 50 lakh
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less ; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments'' in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
(a) Attested Certificates(s) issued by Executive or Nominated Authority of the government Departments or Semi-Government/Public Sector Undertakings for the value of the work done for them during the qualifying period including current financial year certifying the bill amounts paid Agreement-wise and Date-wise or attested photo copy of such certificate. Such certificates will be accepted only from Govt. / Govt. bodies / PSUs authorities. Certificates issued by Private Bodies will not be considered.
NOTE: (i) Financial Year shall normally, be reckoned as 1st April to 31st March of the Next Year. However, for Turnover Criteria, the Financial Year as applicable to the Company /Tenderer is to be considered, if it defers from the above. (ii) Current Financial year is reckoned as the incomplete Financial year in which the date of tender submission falls. (iii) Chartered Accountant statements duly indicating yearly receipts will not be considered until and unless backed by Audited Balance Sheets or Provisional Balance sheet. (iv) (v) If the tender is not accompanied by the certificate(s) in support of financial eligibility as above, the tender shall be rejected. No post-tender correspondence will be entertained.
If JV firms are allowed to participate; Financial eligibility of the JV Firm shall be adjudged based on satisfactory fulfillment of the Para No.17.15.2 of J.V guide lines of IRSGCC April - 2022 [with up to date correction slip].
(a) The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Tenderer shall carefully read clause No. 10 including clause no. 10.1 to 10.5 of IRGCC April 2022.
The total value of similar nature of work completed during the qualifying period and not the payments received within qualifying period alone, shall be considered. In case, final Bill of similar nature of work has not been passed and final measurements have not been recorded, the paid amount including statutory deductions will be considered. If final measurements have been recorded and work has been completed with negative variation, then also the paid amount including statutory deductions will be considered. However, if final measurements have been recorded and work has been completed with positive variation but variation has not been sanctioned, original agreement value or last sanctioned agreement value whichever is lower shall be considered for judging eligibility.
In case JV firms are allowed to participate, Technical Eligibility of the JV Firm shall be adjudged based on satisfactory fulfillment of the Para No.17.15.1 of J.V. guide lines of IRSGCC April-2022 [read with up to date correction slip].
The value of work completed will not include the cost of any materials issued free of cost by the Railway/ Department concerned. Price Variation amount, if any; if indicated / incorporated in the experience certificate will also be considered towards eligibility.
Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organization, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates.
The work experience certificate shall be in the name and style of the 1.5.1 tenderer participating or as per provisions under Clause 17.15 of GCC April-2022 for JV Firm, if eligible to participate.
The work experience certificate shall be issued by an officer not below the rank of JA Grade or Bill passing Officer in Railways and Bill passing Officer/Executive In-charge of work in other Govt. / Govt. bodies / PSUs. The certificate should bear the signature and seal of the issuing officer, name of the department etc. In case tenderer submits work experience 1.5.2 certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Defination of Similar Work :- Any Civil Engineering work.
80 conditions · 25 needing a document upload
Uploading of Proforma-18 attached with Tender document (Certificate signed by Tenderer and Chartered Accountant), w he n balance sheet for the first previous year is yet to be prepared/ audited.
TENDER SHALL BE REJECTED if it is not accompanied by the following
Uploading of Proforma (Proforma-16) attached with Tender Document for self-Certificate in regard to meeting the Minimum Local Content requirements as per Make in India Policy for Procurement Order Value less than of Rs.10 Crores.
Uploading of Proforma (Proforma-17) attached with Tender Document for Certificate from the statutory auditor or cost auditor of the company (in the case of companies) or from a practicing cost accountant or practicing chartered accountant (in respect of suppliers other than companies) giving the percentage of Local Content as per Make in India Policy for Procurement Order Value more than Rs.10 Crores.
Bid Security deposited through IREPS e-payment or as per provisions under Clause 5 (2) Part-I of GCC April 2022.
In case of Partnership firm: The tender form shall be submitted only in the name of partnership firm.
In case tenderer is JV Firm : The tender form shall be submitted 2.3.2 only in the name of the JV and not in the name of any constituent member.
The Bid Security shall be deposited either in cash through e- payment gateway or submitted as Bank Guarantee bond from a scheduled commercial bank of India or as mentioned in tender 2.3.3 documents. The Bank Guarantee bond shall be as per Annexure- VIA and shall be valid for a period of 90days beyond the bid validity period.
In case, submission of Bid Security in the form of Bank Guarantee, following shall be ensured:- i. A scanned copy of the Bank Guarantee shall be uploaded on e-Procurement Portal (IREPS) while applying to the tender. ii. The original Bank Guarantee should be delivered to the Divisional Railway Manager(Works),2nd floor, Irwin Road,South Western Railway, Mysore-570001, within 5 working days of deadline of submission of bids. iii. Non submission of scanned copy of Bank Guarantee with the bid on e-tendering portal (IREPS) and/or non submission of original Bank Guarantee within the specified period shall lead to summary rejection of bid. iv. The Tender Security shall remain valid for a period of 90 days beyond the validity period for the Tender. v. The details of the BG, physically submitted should match with the details available in the scanned copy and the 2.3.4 data entered during bid submission time, failing which the bid will be rejected. vi. The Bank Guarantee shall be placed in an envelope, which shall be sealed. The envelope shall clearly bear the identification "Bid for the ***** Project" and shall clearly indicate the name and address of the Bidder. In addition, the Bid Due Date should be indicated on the right hand top corner of the envelope. vii. The envelope shall be addressed to the Divisional Railway Manager(Works),2nd floor, Irwin Road,South Western Railway, Mysore-570001 viii. If the envelope is not sealed and marked as instructed above, the Railway assumes no responsibility for the misplacement or premature opening of the contents of the Bid submitted and consequent losses, if any, suffered by the Bidder. ix. The benificiary for the PG will be Senior Divisional Finance Manager, South Western Railway, Mysore
Proforma-16 for self-certificate in regard to meeting the Minimum Local Content requirements as per Make in India Policy for Procurement order value less than of Rs. 10 Crores. OR Proforma-17 for Certificate from the statutory auditor or cost auditor of the company (in the case of companies) or from a practicing cost accountant or practicing chartered accountant (in respect of suppliers other than companies) giving the percentage of Local Content as per Make in India Policy for Procurement Order Value more than Rs.10 Crores. Provisions of Make in India Policy 2017 (revised during 2024 vide Department for Promotion of Industry and Trade, Ministry of Commerce and Industry's letter No. P-45021/2/2017-PP (BE-II)-Part(4)Vol.II dated 19.07.2024) issued by Govt. of India, as amended from time to time, shall be followed for consideration of tenders.
Uploading of Proforma -18 attached with Tender document (Certificate signed by Tenderer and Chartered Accountant), w he n balance sheet for the first previous year is yet to be prepared/ audited.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
(i) The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be. (ii) documents shall be submitted according to clause 14 of IRGCC 2022:
MYS Dn: SSE/P.Way/SMET Section:-Construction of Gang tool cum rest room - 17 Nos ( Left Over works)
26MYS26of14-08-2026itno01~SWR
26MYS26of14-08-2026itno01
Open
Works - General
15 Months
Dharwad, Karnataka
₹0
₹2.5 L
14 Aug 2026
14 Aug 2026
24 Aug 2026
80 items across 2 schedules · ₹1,55,18,150.74 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | All kinds of soil | cum | 253.57 | 177.5 | 45,008.68 |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. | cum | 253.57 | 196 | 49,699.72 |
| 3 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) | cum | 58.64 | 7,178.75 | 4,20,961.9 |
| 4 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) | Sqm | 223.91 | 410.85 | 91,993.42 |
| 5 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. | Sqm | 510 | 749.3 | 3,82,143 |
| 6 | Suspended floors, roofs, landings, balconies and access platform | Sqm | 1200 | 927.25 | 11,12,700 |
| 7 | Lintels, beams, plinth beams, girders, bressummers and cantilevers | Sqm | 301.97 | 736.4 | 2,22,370.71 |
| 8 | Under 20 cm wide | Metre | 186.7 | 208.55 | 38,936.29 |
| 9 | Weather shade, Chajjas, corbels etc., including edges | Sqm | 207 | 951.1 | 1,96,877.7 |
| 10 | Providing, transporting, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). | cum | 17 | 20,355.8 | 3,46,048.6 |
| 11 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 41.14 | 9,860.4 | 4,05,656.86 |
| 12 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 249.78 | 9,105.95 | 22,74,484.19 |
| 13 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 276.44 | 7,311.25 | 20,21,121.95 |
| 14 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. | Sqm | 144.49 | 1,267.95 | 1,83,206.1 |
| 15 | Kiln seasoned and chemically treated hollock wood | cum | 2.17 | 83,378.05 | 1,80,930.37 |
| 16 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 57.32 | 2,392.65 | 1,37,146.7 |
| 17 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). | Sqm | 57.32 | 462.35 | 26,501.9 |
| 18 | Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). | Each | 156 | 228.85 | 35,700.6 |
| 19 | 100x58x1.90 mm | Each | 39 | 45 | 1,755 |
| 20 | 250x16x5 mm | Each | 34 | 308 | 10,472 |
| 21 | 250x16 mm | Each | 22 | 260.6 | 5,733.2 |
| 22 | 250x10 mm | Each | 34 | 115.15 | 3,915.1 |
| 23 | 150x10 mm | Each | 56 | 82.55 | 4,622.8 |
| 24 | 100 mm | Each | 156 | 59.55 | 9,289.8 |
| 25 | Single rubber stopper | Each | 34 | 39.6 | 1,346.4 |
| 26 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. | Metre | 67.12 | 570.95 | 38,322.16 |
| 27 | 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames. | Sqm | 29.4 | 3,720.75 | 1,09,390.05 |
| 28 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg | 3400 | 117.35 | 3,98,990 |
| 29 | Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) | Kg | 2154.2 | 131.05 | 2,82,307.91 |
| 30 | Hot finished welded type tubes | Kg | 4250 | 194.4 | 8,26,200 |
| 31 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works | Kg | 1339.29 | 172.6 | 2,31,161.45 |
| 32 | Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete. | cum | 14.6 | 8,595.15 | 1,25,489.19 |
| 33 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. | Sqm | 31.56 | 1,096.55 | 34,607.12 |
| 34 | Size of Tile 600x600 mm | Sqm | 390 | 1,553.45 | 6,05,845.5 |
| 35 | 1:6 (1 cement: 6 fine sand) | Sqm | 2552.33 | 333.35 | 8,50,819.21 |
| 36 | Flush/ Ruled pointing | Sqm | 340 | 385.4 | 1,31,036 |
| 37 | New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre | Sqm | 1495.29 | 185.65 | 2,77,600.59 |
| 38 | New work (Two or more coats applied @ 3.84 kg/10 sqm) | Sqm | 1642.28 | 116.9 | 1,91,982.53 |
| 39 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture | Sqm | 390.93 | 170.7 | 66,731.75 |
| 40 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests | Each | 12 | 6,767.4 | 81,208.8 |
| 41 | White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps | Each | 17 | 2,648.85 | 45,030.45 |
| 42 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. | Each | 17 | 1,607.95 | 27,335.15 |
| 43 | Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 | Metre | 316.8 | 1,180.75 | 3,74,061.6 |
| 44 | Sand cast iron S&S pipe as per IS: 1729 | Metre | 170 | 1,044.75 | 1,77,607.5 |
| 45 | Sand cast iron S&S as per IS - 1729 | Each | 9 | 598.5 | 5,386.5 |
| 46 | Sand Cast Iron S&S as per IS: 1729 | Each | 17 | 1,683.55 | 28,620.35 |
| 47 | Sand Cast Iron S&S as per IS- 1729 | Each | 17 | 1,558.35 | 26,491.95 |
| 48 | Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms | Each | 17 | 367.1 | 6,240.7 |
| 49 | 20 mm nominal dia Pipes | Metre | 75.1 | 335 | 25,158.5 |
| 50 | 25 mm nominal dia Pipes | Metre | 75 | 401.55 | 30,116.25 |
| 51 | 20 mm nominal dia Pipes | Metre | 85 | 537.6 | 45,696 |
| 52 | 25 mm nominal dia Pipes | Metre | 363.68 | 355.4 | 1,29,251.87 |
| 53 | 25 mm nominal bore | Each | 48 | 622.4 | 29,875.2 |
| 54 | 25 mm nominal bore | Each | 17 | 464.05 | 7,888.85 |
| 55 | 25 mm nominal bore | Each | 51 | 439.25 | 22,401.75 |
| 56 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. | Per Litre | 12000 | 11 | 1,32,000 |
| 57 | 15 mm nominal bore | Each | 30 | 506.8 | 15,204 |
| 58 | 150 mm diameter | Metre | 510 | 695.8 | 3,54,858 |
| 59 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 | Each | 33 | 6,937.9 | 2,28,950.7 |
| 60 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 | Each | 12 | 26,861.9 | 3,22,342.8 |
| Schedule total | ₹1,44,94,833.37 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GangTool.pdf
ATTACHMENT
GCCAdvanceCorrectionSlipNo5.pdf Correction Slip No 5 to GCC 2022
ATTACHMENT
IRGCCApril2022.pdf
ATTACHMENT
GCCAdvanceCorrectionSlipNo6.pdf Correction Slip No 6 to GCC 2022
ATTACHMENT
GCCACSCORRECTION.pdf
ATTACHMENT
ACS-3toGCC-2022.pdf
ATTACHMENT
JPOforcablecut.pdf
ATTACHMENT
Proforma161718.pdf
ATTACHMENT
GCCACS11.pdf
ATTACHMENT
GCCAdvanceCorrectionSlipNo9.pdf Correction Slip No 9 to GCC 2022
ATTACHMENT
GCCAdvanceCorrectionSlipNo7.pdf Correction Slip No 7 to GCC 2022
ATTACHMENT
GCCAdvanceCorrectionSlipNo10.pdf Correction Slip No 10 to GCC 2022
ATTACHMENT
GCCAdvanceCorrectionSlipNo8.pdf Correction Slip No 8 to GCC 2022
ATTACHMENT
Correction slip to GCC 2022
ATTACHMENT
ACS-4toGCC-2022.pdf
ATTACHMENT
ACS-2toGCC-2022_2022-CE-1-CT-GCC-2022.pdf
ATTACHMENT
GCCAdvanceCorrectionSlipNo5.pdf
ATTACHMENT
GCCAdvanceCorrectionSlipNo6.pdf
ATTACHMENT
GCCAdvanceCorrectionSlipNo9.pdf
ATTACHMENT
GCCAdvanceCorrectionSlipNo7.pdf
ATTACHMENT
GCCAdvanceCorrectionSlipNo10.pdf
ATTACHMENT
GCCAdvanceCorrectionSlipNo8.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].