SPECIAL REPAIR TO OFFICERS MD ACCN NO P13 COMMA AND 13 COMMA 04 AT ROWRIAH IN JORHAT MILITARY STATION UNDER GE JORHAT

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level), complete all as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for, complete all as directed.

Demolition of reinforced cement concrete of roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4.0 Sqm each, complete all as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as directed.

Materials and labour for, plain cement concrete (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

Material and labour for, plain cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in surface channel and drains, finished the concrete surface even and smooth using extra cement, complete all as specified and directed.

Materials and labour for, plain cement concrete (1:3:6) type C-1 (using 20 mm graded crushed stone aggregate) for holdfast bed block, complete all as specified and directed.

Material and labour for, plain cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as coping and the linke including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

Material and labour for, RCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

Material and labour for providing precast cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain face and set in CM (1:4), complete all as specified and directed.

Material and labour for, 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like over 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite half round including taking down old existing tiles, complete all as specified and directed.

Material and labour for, use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete, complete all as specified and directed.

Material and labour for, 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

Supply and fix for, 2nd class HW, 30mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), complete all as specified and directed.

Supply and fix for, 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides and both faces is covered with decorative face veneer with lipping/ frame to match, complete all as specified and directed.

Supply and fix for, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as per specification & drawing.

Supply and fix for, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as per specification & drawing.

Supply and fix for, 75mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

Supply and fix for, 100mm size stainless steel butt hinges, medium weight, complete all as specified and directed.

Supply and fix for, aluminium anodised, barrel tower bolts of extruded section of size 150mm long, complete all as specified and directed.

Supply and fix for, aluminium anodised, barrel tower bolts of extruded section of size 200mm long, complete all as specified and directed.

Supply and fix for, aluminium handles, cast type, anodised 100mm size complete all as specified and directed.

Supply and fix for, aluminium handles, cast type, anodised 125mm size complete all as specified and directed.

Supply and fix for, aluminium handles, cast type, anodised 150mm size complete all as specified and directed.

Supply and fix for, stainless steel handles,125mm size complete all as specified and directed.

Supply and fix for, 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed.

Supply and fix for, 150mm size floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and directed.

Supply and fix in repair for, door closer cast iron body, hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg, complete all as specified and directed.

Supply and fix for, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Supply and fix in repair for, harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc, complete all as specified and directed.

Supply and fix in repair for, tubular brass chromium plated towel rail 20mm dia, complete all as specified and directed.

Supply and fix in repair for, bracket fancy type, brass chromium plated for towel rail of 20mm dia fixed with wooden block/ PVC through fastener and galvanised screws to wall including drilling and making good to disturbed surfaces, complete all as specified and directed.

Supply and fix for, mild steel flat iron as in band, straps, hold fasts etc. and similar small articles conforming to Fe-410-0 or Fe-310-0, complete all as specified and directed. Note: The hold fast shall be treated in two coats of tar and the cost for the same is deemed to be included in unit quoted rate.

Supply and fix for, rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-290 Gde E-165, complete all as specified and directed.

Supply and fix for, rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410 -W (Gde- E- 250) quality- A, complete all as specified and directed.

Material and labour for, mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Supply and fix for, pressed steel frames 105 x 60mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

Supply and fix for, pressed steel frames 125 x 60mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

Supply and fix for, factory made steel windows with side hungs hutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded as per IS-1038:1983 (Amendment No.3 of May 2009), complete all as specified and directed.

Supply and fix for, factory made steel windows or ventilators, fixed type, with glazing bars as per IS-1038:1983 (Amendment No.3 of May 2009), complete all as specified and directed.

Supply and fix for, aluminium sliding window with powder coating (minimum thickness of powder coating 50 micron) including following components/ specifications, complete all as specified and as shown on drawing No.CESZ/2015/TD/007 Sheet No.1R/5, 3R/5, 4R/5 & 5R/5:- (i) Two leaf glazed sliding shutter and one leaf gauzed (fly proofing) sliding shutter. (ii) Opening of windows exc. 0.90 Sqm but not exc.1.5 Sqm. (iii) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (iv) All vertical/ horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, etc. (vi) Rest all as shown on drawing. Note: Sheet glass, aluminium grill and stainless steel wire mesh shall be measured and paid separately under relavant item.

Supply and fix for, aluminium sliding window with powder coating (minimum thickness of powder coating 50 micron) including following components/ specifications, complete all as specified and as shown on drawing No.CESZ/2015/TD/007 Sheet No.1R/5, 3R/5, 4R/5 & 5R/5:- (i) Top hung gauzed (fly proofing) shutter and bottom portion fixed glazed. (ii) Opening of windows not exc. 0.90 Sqm. (iii) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (iv) All vertical/ horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, etc. (vi) Rest all as shown on drawing. Note: Sheet glass, aluminium grill and stainless steel wire mesh shall be measured and paid separately under relavant item.

Supply and fix, anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement as specified and directed.

Material and labour for, stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement, complete all as specified and directed.

Supply and fix for, pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Supply and fix for, pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Material and labour for, PCC (1:2:4) type B0 (using 12.5mm graded crushed stone aggregate) as roof padding, kerbs or mud stops, benching, rounded or chamfered on edges including necessary formwork, complete all as specified and directed.

Material and labour for, rendering 10 mm (average) thick, cement plaster, in cement mortar (1:3), finished even and smooth without using extra cement mixed with and including integral water proofing compound as per manufactures instructions on roof surfaces and providing 3mm thick (minimum) APP (Atactic Polypropylene Polymer) modified prefabricated five layers, weight not less than 3.5 Kg/ Sqm water proofing membrane, black finished reinforced with non woven polyester matt (weighing not less than 160 gms/ Sqm) with applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per sqm over a coat of bituminous primer @ 0.40 Litre/ Sqm and one coat of bitumen based UV reflective paint with aluminium paint as per manufacturer's instruction over APP membrane. The membrane shall be laid using butane torch and sealing all joints etc., complete all as specified in Para 11.44.5 of SSR Part-I and directed.

Material and labour for, powder coated aluminium snap grid frame work for false ceiling, size of grid 605 x 605mm, including aluminium main / cross tee section of size 35mm x 23mm x 1.5mm (minimum) and aluminium angle 25mm x 23mm x 1.5mm thick, suitable size GI wire hanging arrangement with adjuster all as specified in clause No.10.38 in SSR Part-I and incuding 4mm thick high pressure steam cured non asbestos fibre cement reinforced multipurpose board as per IS 14862 including taking down existing false ceiling system, complete all as specified and directed.

Material and labour in repair for, 19mm thick MDF board prelaminated both side as in kitchen cabinet/ almirah shutter, shelf and partition etc. including lipping, complete all as specified and directed.

Material and labour for, 75mm thick plain cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in plinth protection, finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour for, 25mm thick plain cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in floor, finished cement concrete surface even and smooth with using extra cement, complete all as specified and directed.

Material and labour for, non skid ceramic tiles, coloured 7 to 8mm thick (square/ rectangular) area of each tile exc.0.11 Sqm but not exc.0.18 Sqm as in floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15mm thick screed bed or bedding in cement mortar (1:6) including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Materials and labour for, glazed ceramic coloured tiles, 450 X 350 X 7mm/ 350 X 250 X 7mm thick, on vertical surface of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat in cement mortar (1:4) including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Material and labour for, vitrified ceramic light shade tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding in cement mortar (1:6) including dismantling floor, hearth or wall tiling including cement mortar bedding, removing serviceable tiles to stores and rubbish off the premises, complete all as specified and directed.

All as per serial item No.58.00 but on vertical surfaces over and including 10mm thick backing coat in cement mortar (1:4), complete all as specified and directed.

Material and labour for, chequered cement concrete tiles 20cm x 20cm x 25mm thick with grey cement and pigment, set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed or bedding in cement mortar (1:6), complete all as specified and directed.

Material and labour for, granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in landing and tread over and including 15mm thick screed bed in CM (1:6) including taking down old existing tiles, complete all as specified and directed.

Material and labour for, granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as riser of step over and including 10mm thick screed bed in CM (1:4) including taking down old existing tiles, complete all as specified and directed.

Material and labour for, rendering 15 mm thick, cement plaster, in cement mortar (1:6) on fair faces of brick work or concrete surfaces on walls and finished even and smooth without using extra cement including taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and directed.

Materials and labour for, rendering 15 mm thick, cement plaster, in cement mortar (1:4) on fair faces of brick work or concrete surfaces on walls and finished even and smooth without using extra cement including taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and directed.

Material and labour for, rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement, complete all as specified and directed. (Note: Water proofing compound shall be measured and paid seperately under relevant item).

Supply only integral water proofing compound complete all as specified.

Material and labour for, preparation of old plastered or unplastered decorated wall surfaces by washing rubbing down and applying one coat of white wash, complete all as specified and directed

Material and labour for, preparation of old decorated plastered ceiling surfaces by washing, rubbing down and stopping of distempered and painted surfaces and applying one coat of acrylic base distemper, complete all as specified and directed.

Material and labour for, preparation of newly plastered wall surfaces and applying two coats of acrylic emulsion distemper over a coat primer, complete all as specified and directed.

Material and labour for, complete removal of existing treatment and applying two coats of acrylic emulsion distemper over a coat primer, complete all as specified and directed.

Material and labour for, preparation of newly plastered wall surfaces and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm, complete all as specified and directed.

Material and labour for, complete removal of existing treatment and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm, complete all as specified and directed.

Material and labour for, 4.0mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane, complete all as specified and directed.

Supply and fix for, 4.0 figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sq. m in each pane, complete all as specified and directed.

Material and labour for, 4.8mm thick sheet glass, ordinary quality and fixed with glazing clips, rubber beading and EDPM gasket in square n exc 0.5 sqm in each pane, complete all as specified and directed.

Material and labour for, preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Material and labour for, preparation of new or previously untreated surfaces of steel and iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

Supply and laying of 16mm outer dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings fixed to wall in over head tank or in ground including taking up or down steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

Supply and laying of 25mm outer dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings fixed to wall in over head tank or in ground including taking up or down steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

Supply and fix in repair for, bib tap, fancy type, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and directed.

Supply and fix in repair for, stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, complete all as specified and directed.

Supply and fix in repairs for, stop valves, fancy type, chromium plated, with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, complete all as specified and directed.

Supply and fix for, angle valves, fancy type, chromium plated, cast copper alloy with long shank and cup concealed type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-l smooth finished, and reforming benching as required for 150mm internal dia of pipe, complete all as specified and directed.

Supply, hoisting and fixing, in position of rotational moulded polyethylene water storage tanks in double layers (cylindrical vertical with closed top) of 500 litres capacity with ISI marked and all as specified in IS12701, specified in SSR Part I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule of size 20mm dia including taking down old existing unserviceable tank, complete all as specified and directed.

Supply, hoisting and fixing, in position of rotational moulded polyethylene water storage tanks in double layers (cylindrical vertical with closed top) of 1000 litres capacity with ISI marked and all as specified in IS12701, specified in SSR Part I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule of size 20mm dia including taking down old existing unserviceable tank, complete all as specified and directed.

Supply and fix in repairs for, sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

Supply and fix in repair for, stainless steel kitchen rack wall mounted of size 24" x 36" x 10" all as per Cat No.KPR-312 of make Blue star & silver Shine Diamond or make as specified in PS as approved, complete all as specified and directed.

Material and labour for, waste fittings, brass, chromium plated 50mm dia for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement including PVC waste pipe, complete all as specified and directed.

Supply and fix for, brass chromium plated shower rose 125mm size with or without swivel joints with 225mm long arms, cast copper alloy chromium plated, fixing to 15mm steel pipe or union, complete all as specified and directed.

Supply and fix in repair for, brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed.

Supply and fix in repairs for, vitreous china wash basin, white, flat back, size 550 x 450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

Supply and fix for, vitreous china wash down water closet pan (EWC) (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) with and including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

Supply and fix in repair for, vitreous china squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe), connection to trap and to flushing cistern anti syphonage pipe including provision of PCC or lime concrete bedding and removal of debris, complete all as specified and directed.

Supply and fix in repairs for, PVC valveless, syphonic action type, flushing cistern 10 litres capacity, low level, white, with inlet, ball valve, float and handle with flush pipe of polyethylene of low or high density or PVC 32mm dia including cutting & pinning in ends, making good the disturbed surfaces in cement mortar (1:3), complete all as specified and directed.

Supply and fix for, PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

Supply and fix for, sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed.

Supply and fix in repairs for, health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

Supply and fix for, 15mm bore dia brass CP mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed.

Supply and fix in repair for, 15mm dia CP fancy type wall mixer with 'L' bend including provision of O/H shower & hand shower for mixing hot and cold water with hand shower HSH-1717 and tube all as per Cat No. QQT-7281 of Jaquar or as specified in PS, screwed down for iron pipe, complete all as specified and directed.

Supply and fix in repair for, toilet paper holder with flat recessed type stainless steel, complete all as specified and directed

Supply and fix for, soap dish, stainless steel, fixed to plugs with chromium plated brass screws, complete all as specified and directed.

Supply and fix in repair for, PVC (SWR) floor trap 75mm dia, plain with CP grating including jointing with solvent cement, complete all as specified and directed.

Supply and fix in repair for, PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete all as specified and directed.

Supply and fix in repair for, grating doom 100mm dia of PTMT (Minimum weight 25gms), complete all as specified and directed.

Supply and fix in repair for, grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40gms), complete all as specified and directed.

Supply and fix for, 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm fixed with nuts, bolts etc. including taking down old existing unserviceable pipe, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm fixed with nuts bolts etc. including taking down old existing unserviceable pipe, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) bends any radius with access door, complete all as specified and directed.

Supply and fix for, 110mm dia PVC (SWR) junction single, (Single T) equal or unequal with access door, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal with access door, complete all as specified and directed.

Taking down carefully unservoceable copper/ aluminium point wiring (light, fan, bell, socket or power) including all fittings such as switches, ceiling roses, regulators, sockets, switch boxes etc. complete and making good the disturbed surfaces complete all as directed.

Material and labour for, point wiring with PVC insulated unsheathed stranded FRLSH copper conductor cable of size 1.5 Sqmm in and including PVC rigid concealed conduit (heavy duty) not less than 20mm dia with all necessary fittings and necessary cutting/ chasing etc and making good the disturbed surfaces, including 1.5 Sqmm PVC insulated unsheathed stranded FRLSH copper conductor as earth lead and connected to common earth dolly for one light/ ceiling fan/ exhaust fan controlled by one, one way modular switch, complete all as specified and directed. (Note: (i) Making good the surfaces with plastering and painting matching to the existing surface finished is deemed to be included in unit quoted rate. (ii) Accessories like inner and outer plates will be measured and paid sepwerately under relevant item.)

All as per serial item No.115.00 but for 2 way point on independent board.

All as per serial item No.115.00 but for bell point on independent board.

All as per serial item No.115.00 but for one 5 pin 5 Amps switch socket outlet on independent board.

All as per serial item No.115.00 but for one 5 pin 5 Amps switch socket outlet on same board.

All as per serial item No.115.00 but for wiring with PVC insulated unsheathed stranded FRLSH copper conductor cable of size 2.5 Sqmm including 2.5 Sqmm PVC insulated unsheathed stranded FRLSH copper conductor as earth lead and connected to common earth dolly for one 15/16 Amps socket outlet on independent board.

All as per serial item No.3.00 but for wiring with PVC insulated unsheathed stranded FRLSH copper conductor cable of size 4.0 Sqmm including 4.00 Sqmm PVC insulated unsheathed stranded FRLSH copper conductor as earth lead and connected to common earth dolly for one modular starter 25 Amps.

Supply and fix for, modular metal flush box 1/2 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 3 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 6 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 8 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 2 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 3 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 6 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 8 module, complete all as specified and directed.

Supply and fix for, modular switch 1 way 6A, 1 module, complete all as specified and directed.

Supply and fix for, modular switch 1 way 16A, 1 module, complete all as specified and directed.

Supply and fix for, modular socket, 6A - 2/3 pin combined 2 module, complete all as specified and directed.

Supply and fix for, modular socket 6A/16A - 2/3 pin combined 2 module, complete all as specified and directed.

Supply and fix for, fan step regulator, 120W - 2 module, complete all as specified and directed.

Supply and fix for, ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body, complete all as specified and directed.

Supply and fix for, modular switch 2 way 6A, 1 module, complete all as specified and directed.

Supply and fix for, modular bell push 6A 1 module, complete all as specified and directed.

Supply and fix for, buzzer, Ding Dong AC. 230 volts, single pole, complete all as specified and directed.

Supply and fix for, sub main wiring with two runs of single core 4.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed, 1100 volts grade IS-694 marked drawn through and including 20mm dia rigid PVC concealed conduit, (heavy duty) (ISI marked) with all necessary fittings and necessary cutting/ chasing etc and making good the disturbed surfaces including one run of single core 4.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, unsheathed stranded as continuous earth wire, complete all as specified and directed. Notes: All runs of copper conductor and one run of conduit shall be measured as one unit length.

Supply and fix for, sub main wiring with two runs of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed, 1100 volts grade IS-694 marked drawn through and including 20mm dia rigid PVC concealed conduit, (heavy duty) (ISI marked) with all necessary fittings and necessary cutting/ chasing etc and making good the disturbed surfaces including one run of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, unsheathed stranded as continuous earth wire, complete all as specified and directed. Notes: All runs of copper conductor and one run of conduit shall be measured as one unit length.

Supply and fix for single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, complete all as specified and directed.

Supply and fix in repair for, modular for 25 Amps capacity starter type 2 module for AC and geyser points, complete all as specified and directed. Note: Modular metal box and plate shall be measured and paid separately under relevant item.

Supply and fix for, sheet metal enclosure for DB's when MCBs to be used, SPN 240 volts, 8 ways 200 Amps rated bus bar, metal double door type IP-43, complete all as specified and directed.

Supply and fix for, sheet metal enclosure for DB's when MCBs to be used, SPN 240 volts, 8 way 200 Amps rated bus bar, metal double door type IP-43, complete all as specified and directed.

Supply and fix for, sheet metal enclosure for DB's when MCBs to be used, TPN 415 volts, 4 way 200 Amps rated bus bar, metal double door type IP-43, complete all as specified and directed.

Supply and fix for, VTPN DB double door, having facility to fix MCCB in incomer and MCBs in outgoing TPN 4 way, 415 volts IP-43 protection with metal door complete fitted with bus bars, neutral links, blanking plates including making good the disturbed surfaces, complete all as specified and directed. Note: MCCB & MCB will be measured and paid seperately under relevant item.

Supply, fixing, testing and commissioning for, 6 to 32 Amp, SP 240 volts 10KA 'C' curve miniature circuit breaker (MCB), complete all as specified and directed.

Supply, fixing, testing and commissioning for, 40 Amp, SPN 240 volts 10KA 'C' curve miniature circuit breaker (MCB), complete all as specified and directed.

Supply, fixing, testing and commissioning for, 63 Amp, TPN 415 volts 10KA 'C' curve miniature circuit breaker (MCB), complete all as specified and directed.

Supply, fixing, testing and commissioning for, MCCB 160 Amps, thermal magnetic type 415 volts, 16 KA, 4 pole including taking out old existing unserviceable, complete all as specified and directed.

Supply and fix in repair for, LED tube light fitting 1 x 20W (+/-5%) 220 volt, AC with extruded strip in thermally conductive material and extruded housing in optically efficient material milky white with system lumen efficacy> 120 lumen per watt minimum system 2300 - 2400 and make LED of chip: Osram, Cree, Nichia, Seoul, Sumsung. Integrated electronic driver, SMD based LED constant current supply with double sided connection to avoid short circuit and surge protection greater than 2.5 KV, IP 20 protection and CRI>80, power factor> 0.95, THD less than 15%, correlated colour temperature (CCT) of 6500K, operating voltage of 140 to 270 volt, frequency of 50Hz, burning hours 50000 hours with comprises of CRCA pre-coated metal housing all as per Cat No. SLE BTN T8 20W of make Surya or equivalent model of make as specified in PS, complete all as specified and directed.

Supply and fix for, LED street light fittings of 30W made of pressure die cast aluminium housing with toughened glass cover, IP66 protection, high power LEDs with secondary lenses and system efficay should be minimum 110 lumen per watt and LM79 report should be provided from NABL accredated lab all as per Cat No.SLE UL 30W IP66 LXNG1 of of make Surya or equivalent model of make as specified in PS. Driver should be BIS approved silicon filled potted driver with inbuilt 4KV surge protection and external 10 KV surge protection inside luminaire housing of trouble free service life. THD shall be <10%, power factor>0.95, CCT5700K and brand name should be embossed/ engraved on the LED fitting for traceability till life. Warranty should be 2 years and warranty certificate should be provided on OEM letterhead at the time of delivery, complete all as specified and directed.

Supply and fix for, street light bracket, fabricated out of 40mm bore GI tubing light grade, 1.5m length bend to the shape, mounting with MS clamp of flat iron size 40 x 5mm of suitable length 2 pairs including nut and bolts etc suitable size as directed, complete all as specified and directed.

Refixing of serviceable light fittings or any type LED tube light fittings after repairing necessary minor defect, complete all as directed.

Refixing of old serviceable DBs after repairing necessary minor defect and making good the disturbed surface, complete all as directed.

Refixing of old serviceable MCB any specification, complete all as directed.

Supply and fix for, LED tube light fitting 1 x 10W (+/-5%) 220 volt, AC with extruded strip in thermally conductive material and extruded housing in optically efficient material milky white with system lumen efficacy> 120 lumen per watt minimum system 2300 - 2400 and make LED of chip: Osram, Cree, Nichia, Seoul, Sumsung. Integrated electronic driver, SMD based LED constant current supply with double sided connection to avoid short circuit and surge protection greater than 2.5 KV, IP 20 protection and CRI>80, power factor> 0.95, THD less than 15%, correlated colour temperature (CCT) of 6500K, operating voltage of 140 to 270 volt, frequency of 50Hz, burning hours 50000 hours with comprises of CRCA pre-coated metal housing all as per Cat No.CG-CCS-103-10-65-SL-DP-NWH or make as specified in PS as approved, complete all as specified and directed.

PEE BEE INDIA (BID ID -3446329)

M/S M R CONSTRUCTION & CO (BID ID -3446413)

MD ABIDUR ALI (BID ID -3446406)

M/S GOPAL ROY AND CO (BID ID -3446936)