Construction of Indoor Stadium including badminton court etc., improvement of internal roads with security provisions and external development at New Ministers Colony, Dispur, Ghy-06

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil1.5 m to 3 m

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Supplying chemical emulsion in sealed containers including delivery as specified.Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level : Concrete of M10 grade with minimum cement content of 220 kg /cum

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum

Brick work with common burnt clay modular bricks of class designation 7.5 In foundation and plinth in:Cement Mortar 1:6 (1 cement : 6 coarse sand).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing approved brand and manufacture SS 304 grade Top & Bottom Patch fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade H type 900mm Pull Handle with 32mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Glass to Glass Lock Round type with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing 12 mm thick frameless toughened glass partitions of approved brand and manufacturer, including providing and fixing partitions at top & bottom with aluminum channel etc. all complete as per direction of Engineer-in-charge

Dry Wall Partition Providing and fixing partition upto ceiling height consisting of 89mm Light Gauge steel (LSG) Frame and required board, including providing and fixing of frame work made of special section, consisting of floor and ceiling channel. The boards are to be fixed tothe frame work with joints staggered to avoid through cracks, M.S. fixing channel of 89 mm width to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, Everest Jointing Compound (25kg/bag), Fibre Mesh Tape, Gypsum Jointing Compound (, Dia 6mm Backer Rod, Fire cum acoustical sealant suitable for board as per manufacture's specification and direction of engineer in charge all complete. 6mm Everest Heavy Duty Board + 9mm Everest Heavy Duty Board (EXTERNAL SIDE) + 89mm LGS Frame (with Insulation) + 12mm Everest Board + 12.5 mm Gypsum Fireline Board+12.5 mm Gypsum Fireline Board (INTERNAL SIDE)

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain white color board of required size with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel screws etc. all as per direction of Engineer-In- Charge. (Note: stainless steel screws shall be paid separately) 12 mm thick

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete:

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

(2) Second layer: Insulation – Layer of Rockwool insulation of 100mm thickness each minimum 60 kg/m³ density with thermal conductivity of K=0.038 W/mk at 20 degrees Celsius when tested to ASTM C518. (3) Third layer: Single layer of aluminium foil of minimum thickness 0.2 mm. (4) Fourth Layer - Aluminium Halters of suitable height with thermal barrier pads to be fixed to the sub purlins with SS 304 screws only 5) Fifth Layer: Steel Deck liner – Solid 28- 35 /200-250 galvalume colour coated steel deck liner (GSM 150) 550 MPa, 0.5 mm TCT 1000 mm ribs spanning up to 1400 mm maximum centres (multiple spans). The finish to the exposed surface of the liner will be polyester coating with film thickness of 23μm +/- 2 μm 2- Aluminium Flashing 0.9mm thick: Flashings manufactured from aluminium alloy AA 3004(AlMn1Mg1) as specified in BS EN 1396: 2007 material thickness of 0.9 mm and Fluorocarbon PVDF finish on the exposed surface. The material shall be same colour& material as of roofing sheet. Girth – 400mm to 560mm. 3- Supply & Fixing of Aluminium gutter of 2mm thickness alloy AA1100 or equivalent. Gutter shall be of girth 1200mm.Provision of down take spouts of dia 200 mm shall be provided . Gutter expansion joint shall be used at appropriate distance

Providing and laying Sports wooden flooring with Hevea ABC Grade 20mm wood with LVL PRO II, having a good backing layer made up of plastic laminate or melamine as specified by the manufacturer and approved by Engineer-incharge.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Extra for pre finished nosing to treads of steps of Granite stone. (Derived From DAR)

Extra for Granite stone flooring in treads of steps and risers using single length up to 2.00 metre .(Derived From DAR)

CEMENT PLASTER (IN COARSE SAND) 12 mm cement plaster of mix : 1:6 (1 cement : 6 Course sand)

CEMENT PLASTER (IN COARSE SAND) 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement : 6 Course sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately) : For fixed portion Powder coated aluminum (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminum (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Filling the gap in between aluminum frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing GI wire etc. complete as per directions of Engineerin- Charge.

Supply and installation of High pressure Compact Laminates (HPL) in choice of WOODEN Shades , Decorative Exterior panels meeting European norm compliance of CE mark with Electron Beam curing (EBC) having standard dimensions of 2800x1300x6mm or 3050x1300x60mm. It has to be high resistance to impact, scratching, fire , water, humidity and due to its high density, it should not decompose and should be resistant to bacteria. HPL to be installed as per the architectural intent on Aluminium frame work having size of 25x38x1.6mm thick at every 450mm vertical interval & 25x75x1.6mm thick at grooves junction with powder coated rivets, considering all structural requirement as per the manufacturer's specification.

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.

Supplying, fitting and fixing PVC blind Pipe as per IS :1281 of 150 mm dia approved including joining ,fitting and fixing etc. exposed/concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages, as necessary complete at all levels including below G.L as directed and specified.

Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing 18mm thick Granite stone work for wall lining upto 10 m height in cement mortar 1:3 (1cement : 3 coarse sand) including pointing with white cement mortor with an admixture of pigment to match the granite shade complete as per direction of Engineer-in-charge.

75 mm thick GRANITE STRIP Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately)

Providing and mixing integral crystalline admixture for water proofing treatment to RCC structures like basement raft, retaining walls, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc. at the time of transporting of concrete into the drum of the ready-mix truck , using integral crystalline admixture @0.80% (minimum) to the weight of cement content per cubic meter of concrete) or higher as recommended by the manufacturer's specification in reinforced cement concrete at site of work. The material shall meet the requirements as specified in ACI-212-3R- 2010 i.e. by reducing permeability of concrete by more than 90%, compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure. The crystalline admixture shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. vertical surface two coats @ 0.70 kg per sqm

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. For horizontal surface one coat @1.10 kg per sqm.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab upto 0.50 sqm

Providing and laying 40 mm Thk Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Providing and fixing soil, waste and vent pipes : 100 mm dia Sand cast iron S&S pipe as per IS: 1729

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

20 mm Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.

Providing and fixing up to floor five level precast cement concrete string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, etc., including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of required Centering complete. 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20mm nominal size derived from natural sources)

Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10mm wide filled with same mortar including ruled pointing etc. complete as per direction of engineer-in-charge.

Supply, fabricating, transporting, hoisting and fixing in position good quality durable solid Granite in various elements for all level . Stone shall be free from cracks, lines, stains, white spots of efflorescence and even in shade for each elements. The stone shall be fine grained and reddish or buff-colored (locally available). The work shall be carried out as per attached drawings with differant process of i.e carving (manual/ by machine), ornamental work, traditional work, figure work (any type, any size), CNC cutting, moulding. The carving and molding work shall be of very good quality. The stones to be fixed in line, level and plumb in all respect with the use of brass clamps, pins, dowels, cement slurry with matching pigment and Epoxy of Akemi Germany, Ardex Endura, MYK laticrete or approved make as required and as approved by the Architects.

Supplying and planting of Aesthetic Plant-'CALOPHYLLUM INOPHYLLM' (Size: 12 Feet ht.) on Planter Box including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'MIMUSOPS ELENGI(SPANISH CHERRY)' (Size: 10 Feet ht.) on Planter Box including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'XANADU(THAUMATOPHYLLUM' (Size: 1 Feet ht.) on Planter Box including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'PEACE LILY (PATHIPHYLLUM)'(Size: 1.5 Feet ht. )on PLILYlanter Box including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'FICUS LONG ISLAND(Size: 3 Feet ht.) on PLILYlanter Box including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and placing in position of PLASTIC POT 14 INCHES etc.complete as specified and directed.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm

Supplying and stacking of good earth at site including royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).

Supplying and planting of Aesthetic Plant-'FICUS BLACK' (Size: 1.5 Feet-2 Feet high) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'RHAPHIS EXCELESA' (Size: 2.5 Feet-3 Feet high) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'GOLDEN BAMBOO'(Size: 7 Feet-8 Feet high) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'PHILIODENDRON SELLOUM' (Size: 1.5 Feet -2 Feet high) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'PHILIODENDRON XANADU (Size: 1.Feet high) WITH 8-10 SUCKERS' on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'(PEACE LILY) SPATHIPHYLLUM WALLISI (Size: 1.5 Feet high ) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'CANNA INDICA '(Size: 2 Feet-2.5 Feet high) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'ALPINIA ZERUMBET(GINGER) '(Size: 2 Feet -2.5 Feet high) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'HYMENOCALIS LITTORALS SPIDER LILY '(Size: 1.5 Feet -2 Feet high) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'PANDANUS BAPTISITII (PANTUS) '(Size: 10 INCHES -12 INCHES) (3-5 CANES) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying, and laying of GRASS CARPET (MAXICAN) for landscaping the area with all necessary accessories, etc. complete as directed.

Supplying and planting of Aesthetic Plant-'ALSTONIA SCHLARIS (CHATIM,DITA BARK)'(Size: 10 INCHES -6.6 Feet high) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'CHORASIA SPECIOSA'(Size: -6.6 Feet High )on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'BAMBUSA BUDHA BELLY PALM'(Size: 8 Feet High) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'CARYOTA URENS (FISHTAIL PALM)' (Size: 8 Fee--9 Feet High) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-WODYETIA BIFURCATA(FOXTAIL PALM) ' (Size: -8-9 Feet High) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'ARECA PALM'( Size: -8-9 Feet High) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'BISMARCKIA PALM' (Size: -5 Feet High )on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'LIVISTONA ROTUNDIFOLIA (FOOTSTOOL PALM' (Size: -3 Feet High) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'ALOCASIA MARCRORHIJHA ' (Size: -3-5 Feet High) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'RAVENALA MADAGASCARIENSIS (TRAVELLER'S PALM )' (Size: -6.60 Feet High) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'ASPIDISTRA ELETIOR' (Size: -1.5-2 Feet High) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'MAIDEN HAIR FERN' on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'CARDYLINE FRUTICOSA (BABY DOLL)' (Size: -2-2.5 Feet High) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'COLOCASIA ESCULENTA (KACU)(ELEPHANT EARS)' (Size: -1-1.5 Feet High) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'AGAONEMA GREEN ' (Size: -1.5 Feet-2 Feet High) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'TRADESCANTIA SPATHACEA ' (Size: -10 INCHES -12 INCHES High)(3-5 CANES) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'SANSEVIERIA TRIFASCIATA (SNAKE PLANT) '(Size: -2 Feet High) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'TRINAX RADIATA (FLORIDA THATCH PALM'(Size: -5 Feet High) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'AGAVE DESMETTIANA '(Size: -3 Feet -4 Feet High) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-'HELICONIA PSITTACORUM '(Size: -2 Feet -2.5 Feet High) on ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia. and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge.

Providing hard stone soling of required thickness (or as specified in drawing) in layers not exceeding 20 cm in depth under foundation,flooring,under pavement,under plinth protection,under ramp, consolidating each deposited layer by ramming, watering and rolling with ½ tonne roller or wooden or steel rammers where ever required including preparing of surface etc. complete as per the direction of Engineer-in-charge.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Centering and shuttering including strutting, propping etc. and removal of form forSuspended floors, roofs, landings, balconies and access platform

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size 600 x 1200 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & atching pigments etc. complete. Size of Tile 600x600 mm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge),minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made Frame size 65 x 150 mm

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 125 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Supplying and fixing C.I. cover without frame for manholes : 560 mm diameter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg

Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

Supplying ,fitting & fixing of Termite treated eco friendly split bamboo cladding with diameter (75mm approximatly) having a minimum length of 2.45m height fixed with SS (grade-304 ,self drilling screws of fasteners 7.5mm length) bolts with nuts and washer to steel beam enamal paint inside and polishing in high gloss malamine clear polish on outside surface complete and as directed.

Supplying ,fitting & fixing of Termite treated eco friendly split bamboo cladding on both side of the existing boundary wall with diameter (75mm approximatly) having a minimum length of 2.45m height fixed with SS (grade-304 ,self drilling screws of fasteners 7.5mm length) bolts with nuts and washer to steel beam enamal paint inside and polishing in high gloss malamine clear polish on outside surface complete and as directed.

Providing and fixing of Portable Security Cabin 6 Feet x 9 Feet of uPVC mulipanel with Metallic Frame,Assam Type Roofing ,4 chali with 12mm cement board with bricks pattern shingles on top, uPVC windows in all sides,18mm cement board with vinyl flooring,one door,all etectrical connection i.e.Fan & Light,Charging Pont etc.complete in all respects .

Providing and fixing of Portable Security Cabin 5 Feet x 6 Feet of uPVC mulipanel with Metallic Frame,Assam Type Roofing ,4 chali with 12mm cement board with bricks pattern shingles on top, uPVC windows in all sides,18mm cement board with vinyl flooring,one door,all etectrical connection i.e.Fan & Light,Charging Pont etc.complete in all respects .

Providing and fixing of Portable Security Cabin 14 Feet x 8 Feet of uPVC mulipanel with Metallic Frame,Assam Type Roofing ,4 chali with 12mm cement board with bricks pattern shingles on top, uPVC windows in all sides,18mm cement board with vinyl flooring,one door,all etectrical connection i.e.Fan & Light,Charging Pont etc.complete in all respects .

Providing and fixing of Portable Security Cabin 6 Feet x 7 Feet of uPVC mulipanel with Metallic Frame,Assam Type Roofing ,4 chali with 12mm cement board with bricks pattern shingles on top, uPVC windows in all sides,18mm cement board with Vinyl Flooring,one door,all etectrical connection i.e.Fan & Light,Charging Point etc.complete in all respects .Security Cabin will be 10 Feet above from Ground Level including 19 to 20 step stairs with Hand Rail.respects .

Providing and fixing of Portable Security Cabin 8 Feet x 12 Feet of uPVC mulipanel with 6 Feet x 12 Feet Varendah with Metallic Frame,Assam Type Roofing ,4 chali with 12mm cement board with bricks pattern shingles on top, uPVC windows in all sides,18mm cement board with vinyl flooring,one door,all etectrical connection i.e.Fan & Light,Charging Pont etc.complete in all respects .

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 160 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single Push Fit Coupler 110 mm dia

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single Push Fit Coupler 160 mm dia

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe (Plain) 110 mm dia

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe (Plain) 160 mm dia

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm dia

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 160 mm dia

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing hand shower (Health faucet) with 1.2mtr long with 8mm dia Easy Flex Tube with wall hook and flow restrictor with flow rate 6 litre per minute at 3 bar in chrome finish and wall hook.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing & fixing toilet paper holder C.P. brass

Providing & fixing Nickel Chromium Plated liquid soap container/dispenser with metallic bottle of approved brand & make 112 mm distance from wall of standard shape with bracket (Nickel chromium plating should pass Salt Spray Test for 200 hours) of the same materials with snap fittings of approved quality and colour, complete as per direction of Engineer in Charge.

Providing and fixing white vitreous china Oval shaped wash basin for top/under counter mounting with 15 mm C.P. brass pillar tap of auto closing type of approved quality and make with, including painting of fittings and brackets, cutting and making good the walls whereever required. White Vitreous China Oval shaped Wash basin size 545 x 545 x 180mm with 15 mm C.P. brass pillar tap auto closing type of approved make with flow rate 2.5 litre per minute at 3 bar .

Providing and fixing CP brass 2 Way Bib cock with wall flange with flow restrictor with flow rate 2.5 litre per minute at 3 bar.

Providing and fixing SS Grating of 125 mm dia of approved quality and colour complete as per direction of engineer in charge. Circular Type125 mm nominal dia with 25 mm waste hole

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on Wall 50 mm nominal dia Pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25mm nominal bore

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S (non modular) bricks of class designation 7.5

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S (non modular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass angle valve for basin mixture and geyser points of approved quality confirming to IS: 8931.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 25 mm dia nominal bore

Supplying, installation, testing and Commission ofGloster 3.5CX120 SQMM AL XLPE Cable as per IS 7098 Part 1 complete with all accessories with necessary as required and as directed by the department Gloster 3.5CX120 SQMM AL XLPE Cable as per IS 7098 Part 1

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 120 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 120 sq. mm

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 120 mm dia (OD-120 mm & ID-103 mm nominal)

Supplying including installation, commissioning of vermin and dust proof totally enclosed, Phosphatised Powder Painted cubical outdoor type double door, floor mounting compartmentalize panel board of size 1.50M X 1.35MX 0.40M made of 16 SWG1.66 m thick C.R. sheet and 40mm X 40mm X 5mm size angle having 4 no legs at the bottom and C.R. sheet roofing on the top complete painting with 2 coats of Red Oxide metal primer and 2 coats of enamel paint. The panel board is to be erected in 1 : 3 : 6 PCC foundation including excavation of trench and brick soling etc. complete neatly Wiring done with provision for one no 630A 4pole MCCB or Switch Fuse Unit as incomer and provision for 6nos DP or TPN out going as specified and directed by the deptt. confirming to IP 65 protection comprising of the following electrical items:

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required Group A

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 A socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required 12 Module (200mmX150mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 12 Module

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required 63 A

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required 63 A

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supplying, installation, testing and Commission of the following indoor Decorative Recess mounted LED down lighter luminaries of model no- DN296B LED15S-6500PSU WH HSN code 9405 complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Philips/Jaquar / LT / Wipro make).

Supplying, installation, testing and Commission of GLINT Linear Canopy is a special, multi-functional LED luminaire designed to replace traditional square under canopy lights in fuel bunks ( GLINTCAR80WLED857PIWBTOLTG) complete with all accessories with necessary as required and as directed by the department.GLINTCAR80WLED857PIWBTOLTG

Supply of Outdoor Unit : VRF OUTDOOR UNITS (Make: Toshiba)Supply of Hi efficient latest generation Imported Top/Side Discharge Type DC Inverter Outdoor VRF units equipped with Variable refrigerant flow unit, comprising Full Inverter driven compressors with fully factory charged Eco friendly R-410A refrigerent gas. 8HP OUTDOOR UNIT WITH FULL DC INVERTER COMPRESSOR

Supply of Hi efficient latest generation Imported Top/Side Discharge Type DC Inverter Outdoor VRF units equipped with Variable refrigerant flow unit, comprising Full Inverter driven compressors with fully factory charged Eco friendly R-410A refrigerent gas. 10HP OUTDOOR UNIT WITH FULL DC INVERTER COMPRESSOR

Supply of Hi efficient latest generation Imported Top/Side Discharge Type DC Inverter Outdoor VRF units equipped with Variable refrigerant flow unit, comprising Full Inverter driven compressors with fully factory charged Eco friendly R-410A refrigerent gas. 16HP OUTDOOR UNIT WITH FULL DC INVERTER COMPRESSOR

Supply of Hi efficient latest generation Imported Top/Side Discharge Type DC Inverter Outdoor VRF units equipped with Variable refrigerant flow unit, comprising Full Inverter driven compressors with fully factory charged Eco friendly R-410A refrigerent gas. 22HP OUTDOOR UNIT WITH FULL DC INVERTER COMPRESSOR

Supply of VRF INDOOR Unit : (Make: Toshiba) 8.5TR

Supply of VRF INDOOR Unit : (Make: Toshiba) 11.otr(Single CDU)

Supply of VRF Indoor units address setting and capacity as mentioned below. Multi speed motor, coil section with DX coil, outer cabinet, drain pan mechanism insulation, pipe connections of various capacities. Cassette type 4-Way VRF Indoor 2.6 TR with Grill Panel

Supply of AHU Expansion kit (Expansion kit should be of EEV type) and control kit suitable for VRF ODU Connection ( Multiple kits of 20HP each for better performance) including Corded Remote Controller with LCD Display for controlling AHU kit

SITC of Control cabling for VRF to be laid within hard PVC conduit pipes with proper bends and accessories (Make: Havells/Polycab/USHA/RR Kabel/Equivalent) 1.5 sq.mm. 2-core shielded communication cable between indoor units and outdoor unit

SITC of CPVC Drain Piping with 6MM Nitrile rubber insulation. Drain pipes to be suspended from slab using full threaded rods and slotted channel along with all required accessories (Make: Ashirwad/Supreme/Ajay/Prince/Equivalent.) Drain piping 25 mm dia

Supply & installation of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Mandev/Chile/ Mexflow/Totaline or Equivalent). (Insulation make: K-Flex, Accoflex, Armacell,Totaline) Quality & Test Certificate to be provided All the insulation should be covered with Treated Woven Glass Cloth laminated on one side. It shall be treated water based acrylic binder to give crisp and non-piling property to the fabric, to help in easy installation, minimize fiber erosion, good aesthetics and resistance to abrasion. Refrigerant piping 28.6 mm dia with (19MM Class 'O' Insulation Laminated with Glass Cloth) (18G Copper Pipes)

Supply & installation of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Mandev/Chile/ Mexflow/Totaline or Equivalent). (Insulation make: K-Flex, Accoflex, Armacell,Totaline) Quality & Test Certificate to be provided All the insulation should be covered with Treated Woven Glass Cloth laminated on one side. It shall be treated water based acrylic binder to give crisp and non-piling property to the fabric, to help in easy installation, minimize fiber erosion, good aesthetics and resistance to abrasion. Refrigerant piping 22.2mm dia with (19MM Class 'O' Insulation Laminated with Glass Cloth) (18G Copper Pipes)

Supply & installation of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Mandev/Chile/ Mexflow/Totaline or Equivalent). (Insulation make: K-Flex, Accoflex, Armacell,Totaline) Quality & Test Certificate to be provided All the insulation should be covered with Treated Woven Glass Cloth laminated on one side. It shall be treated water based acrylic binder to give crisp and non-piling property to the fabric, to help in easy installation, minimize fiber erosion, good aesthetics and resistance to abrasion. Refrigerant piping 19.1mm dia with (19MM Class 'O' Insulation Laminated with Glass Cloth) (1mm Thck. Gauge)

Supply & installation of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Mandev/Chile/ Mexflow/Totaline or Equivalent). (Insulation make: K-Flex, Accoflex, Armacell,Totaline) Quality & Test Certificate to be provided All the insulation should be covered with Treated Woven Glass Cloth laminated on one side. It shall be treated water based acrylic binder to give crisp and non-piling property to the fabric, to help in easy installation, minimize fiber erosion, good aesthetics and resistance to abrasion. Refrigerant piping 15.9mm dia with (19MM Class 'O' Insulation Laminated with Glass Cloth) (1mm Thck. Gauge seamless tubing)

Supply & installation of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Mandev/Chile/ Mexflow/Totaline or Equivalent). (Insulation make: K-Flex, Accoflex, Armacell,Totaline) Quality & Test Certificate to be provided All the insulation should be covered with Treated Woven Glass Cloth laminated on one side. It shall be treated water based acrylic binder to give crisp and non-piling property to the fabric, to help in easy installation, minimize fiber erosion, good aesthetics and resistance to abrasion. Refrigerant piping 12.7mm dia with (19MM Class 'O' Insulation Laminated with Glass Cloth) (0.8mm Thck. Gauge seamless tubing)

Supply & installation of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Mandev/Chile/ Mexflow/Totaline or Equivalent). (Insulation make: K-Flex, Accoflex, Armacell,Totaline) Quality & Test Certificate to be provided All the insulation should be covered with Treated Woven Glass Cloth laminated on one side. It shall be treated water based acrylic binder to give crisp and non-piling property to the fabric, to help in easy installation, minimize fiber erosion, good aesthetics and resistance to abrasion. Refrigerant piping 9.5mm dia with (19MM Class 'O' Insulation Laminated with Glass Cloth) (0.8mm Thck. Gauge seamless tubing)

Supply & installation of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Mandev/Chile/ Mexflow/Totaline or Equivalent). (Insulation make: K-Flex, Accoflex, Armacell,Totaline) Quality & Test Certificate to be provided All the insulation should be covered with Treated Woven Glass Cloth laminated on one side. It shall be treated water based acrylic binder to give crisp and non-piling property to the fabric, to help in easy installation, minimize fiber erosion, good aesthetics and resistance to abrasion. SITC of Imported Refenet Joints for Indoor Units & AHUs

Supply, Installation and balancing of Imported Textile Ducting with all relevant mounting material with the followninng spefications: (Make: Prihoda - Made in Europe/China) Color of the fabric as per standard RAL code by manufacturer The textile to be 100% polyester, Endless fibre (multifilament) Washing shrinkage (warp/weft) 0,5/0,5 % by 40°C according to EN ISO 6330-2000 Internal retention rings and end tensioner to provide shape retention when there is NO AIR Duct to have Micro Perforation for even air diffusion

Supply, Fixing, Testing and Balancing of GI sheet metal Site Fabricated rectangular ducting as per IS 655 complete with turning vanes , companion flanges , structural support , sealing of all seams with a suitable metal sealant, completely leak proof as per drawings (Make: Tata/Sail/Bhushan/Arti) 22 G GI Sheet

Supply and fixing of 100% Thermal insulation with Class - 'O' Closed cell nitrile rubber insulation sheet duly pasted on the duct inside surface using SR988 or approved equal adhesive. (Insulation make: K-Flex, Accoflex, Armacell,Camipro,Totaline) Quality & Test Certificate to be provided 19MM

Supply, Fixing, Testing and Balancing of GI sheet metal Factory Fabricated Spiral Round ducting as per IS 655 complete with Pre-insulated Double Walled Spiral Round ducts with 13MM Class ’O’ nitrile rubber which will be insulated internally on 100% of the ducts including Grill Collars as per your production sheet for (Make: Tata/Sail/Bhushan/Arti) 22 G GI Sheet

Supply, Fixing, Testing and Balancing of GI sheet metal Factory Fabricated Spiral Round ducting as per IS 655 complete with Pre-insulated Double Walled Spiral Round ducts with 13MM Class ’O’ nitrile rubber which will be insulated internally on 100% of the ducts including Grill Collars as per your production sheet for (Make: Tata/Sail/Bhushan/Arti) 24 G GI Sheet

Supply, installation, testing and balancing of Linear Discreet Grill with 15 Deg Deflecting linear bars in extruded aluminum construction with white powder coated finish. (Make: Airflow/Ravistar/Premier /Caryaire/Waves)

Supplying, fixing, testing & balancing of GI made volume control dampers as per specifications.

Canvas connection for AHU with fire retardant material

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, duly place with MS supports including bolts & nuts, painting suspenders etc as required. All cable trays to be covered with C-Type inverted cover made out of 24G Galvanized Plain sheet and duly screwed/bolted for rigidity. 200 mm width x 50 mm depth x 1.6 mm thickness.

VI Rubber Pading for outdoor units

90 Degrees angle cowling for top discharge VRF outdoor unit with bird screen grille as per size of the units made out of 24Gauge GI Sheet

Supply, installation, testing and commissioning of Wall mounted cubical type starter panel, fabricated from 2.0 mm thick CRCA Sheet duly powder coated of suitable size , internally Wired, operate on 415 Volts, 3- Phase, 4 Wire, 50 Hz AC power (Make: L&T/Carrier) 32Amps TPN MPCB-1 No. Thermal overload relay, electronic timer - 1 No. EachON/OFF/TRIP Indication lamps-1 setStart/Stop Rotary Switch -1 No.Phase indication lamp-1 set Voltage Scanner with phase indication, power supply indication

SITC of Adjustable/Controllable Pitch Impeller & Direct Driven Type Axial Flow Fan along with canvas connection between duct and fan. (Make: Airflow/Nikotra) UL Listed for 400 Degree Celcius/30 Mins; 300 Degree Celcius/2 hrs & 250 Degree Celcius/2 hrs in accordance with "Power ventilators for smoke control" 2500 CFM/25MM WG SP

SITC of Adjustable/Controllable Pitch Impeller & Direct Driven Type Axial Flow Fan along with canvas connection between duct and fan. (Make: Airflow/Nikotra) UL Listed for 400 Degree Celcius/30 Mins; 300 Degree Celcius/2 hrs & 250 Degree Celcius/2 hrs in accordance with "Power ventilators for smoke control" 3000 CFM/25MM WG SP

SITC of wall mounted IP65 Hinged Water Proof Polycarbonate ABS enclosure for outdoor ambient use for placing MCB with 3-Phase MCB of ratings as stated below 32AMPS 4-Pole MCB

SITC of wall mounted IP65 Hinged Water Proof Polycarbonate ABS enclosure for outdoor ambient use for placing MCB with 3-Phase MCB of ratings as stated below 63AMPS 4-Pole MCB

SITC of 8MP Bullet camera : Built-in IR (m) 40 m; Field of View wide (°) 46 – 97 ° Frame rate (fps) 1 – 30 fps Impact protection (EN 50102) IK10 IP rating IP66; Resolution 3840 x 2160; 1920 x 1080; 1280 x 720; 1536 x 864; 2560 x 1440; Sensor type 1/1.8 inch CMOS Video compression H.264 (ISO/IEC 14496-10); M-JPEG; H.265/HEVC.

SITC of 4MP PTZ Camera: HDR 30x Zoom; Enclosure: IP66 pendant IR30X, Frame Rate 60 fps;, Sensor type 1/1.8 inch HD CMOS; Sensor resolution 2688 x 1520 (4 MP); Detection 60 m (197 ft); Pan Range 360° continuous; Tilt Angle -90° to 5° (Auto-flip 190°);

SITC of Pendant wall mount: Construction Material; Aluminum alloy; Weather resistant finish; Vandal resistant design for indoor and outdoor use.

SITC of Wall mount plate: Construction Material; Aluminum alloy; Weather resistant finish; Vandal resistant design for indoor and outdoor use

SITC of IP video management solution with up to 96 TB storage capacity (Without HDD): RAID-5 protected , all-in-one video management solution for up to 256 channels Storage: Internal storage HDD; Maximum internal hard drives 8, Processor Intel® Xeon® E-2226GE Installed memory 16GB

SITC of IP License Plus Base for IP video management solution: Number of Channels 32 Channel( Expansion Software)

SITC of Software Maintenance (SMA) license: 1 year Maximum number of workstations 20 Maximum number of cameras 256 Maximum number of live and playback sites 10 Maximum number of intrusion panels 10 Maximum number of DVRs 10 Maximum number of VRMs 2.

Supply and Installation of 12TB Surveillance grade Hard Drive for Storage.

Supply and Installation of i7 Desktop PC. Processor 12th Gen Intel® Core™ i7-12700 (25 MB cache, 12 cores, 20 threads, 2.10 GHz to 4.80 GHz Turbo) Operating System Windows 11 Home Single Language, English Video Card Intel® UHD Graphics 770 Monitor Dell 22 Monitor - E2222H Memory 16 GB, 1 x 16 GB, DDR4, 3200 MHz Hard Drive 512 GB, M.2, PCIe NVMe, SSD

Supply , Installation , Testing and Commissioning of L3 managed full 10G Ethernet core routing switch with 24*1/10G SFP+ fiber ports and 4*40/100G QSFP28 fiber slot ports. Redundant dual AC power supply. Core Switch with switching capacity of 1.28Tbps. (Make: Juniper / Nexxus / Allied Telesys)

Supplying, installation, testing and commissioning of 16-Port KVM over IP Switch with 16 nos USB VGA Virtual Media KVM Adapter complete as required (Make:- D-Link/ Aten/ Netgear)

Supply, Installation, Testing and Commissioning of Cat 6 Keystone I/O Port. (Make:- D-Link/ Digisol/ Derwiser)

Supply and Installation of Wireless Access Point (Make:- D-Link/ Digisol/ Netgear)

Supply and Installation of Cat6 Patch cord 2 Mtr (Make:- D-Link/ Digisol/ Derwiser)

Supply and Installation of Cat6 Patch cord 1 Mtr (Make:- D-Link/ Digisol/ Derwiser)

Supplying, installation, testing and commissioning of 16 Port CAT6 Universal Patch Panel with Individual Port Transparent Shutter, (Unloaded/Loaded) with Cable Support Bar. (Make:- D-Link/ Digisol/ Derwiser)

Supply ad Installation of 4U Wall Mountable Equipment Rack (Make:- D-Link/ Digisol/ Derwiser)

Supply ad Installation of 17U Floor Mountable Equipment Rack (Make:- D-Link/ Digisol/ Derwiser)

Supply, Installation, Testing and Commissioning of 85‑inch 4K Ultra HD HDR Professional Display. Display Device:- LCD, Backlight Type:- Direct (Full Array LED), Brightness (cd/m2) (*1):- 620 (Peak Brightness: 850 *1), Contrast Ratio:- (*1)4000:1, Dynamic Contrast Ratio:- 600000:1, (Make:- LG/ Panasonic/ Samsung)

Supply and Installation of 6KVA Online UPS System with 120 Min Back up Battery Bank and inbuilt Isolation Transformer. (Make:- Numeric/ Delta/ Vertive)

Supply and Laying of Armoured Cat 6 UTP Cables (Make:- D-Link/ Digisol/ Derwiser)

Supply and Laying of Cat6 UTP Cables (Make:- D-Link/ Digisol/ Derwiser)

Supply and Laying of 1.5 Sqmm 3 Core Armoured Electrical Cable (Make:- Finolex/ Havells/ KEI)

Supply and Installation of Electrical accessories, PVC Boxes etc

Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and making good the walls etc. Internal work - Exposed on wall 20 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and making good the walls etc. Internal work - Exposed on wall 25 mm dia nominal bore

Supplying, installation, testing and Commission of Gate top Die cast aluminium housing, clear PC diffuser, IP65 complete with all accessories with necessary as required and as directed by the department. 12W Gate Top Die cast aluminium housing, clear PC diffuser, IP65

Supplying, installation, testing and Commission of Projector Series Die cast aluminium housing, transparent tempered glass diffuser, IP65 complete with all accessories with necessary as required and as directed by the department. Bollard Die cast aluminium housing, opal white PC diffuser, Projector Series Die cast aluminium housing, transparent tempered glass diffuser, IP65

Supplying, installation, testing and Commission of Linea LED Strip Light Bright 28W with driver complete with all accessories with necessary as required and as directed by the department. 28W Linea LED Strip Light Bright 28W with driver

Supplying, installation, testing and Commission of ALUMINIUM CABLE 3 CORE 6 SQMM complete with all accessories with necessary as required and as directed by the department.GLOSTER 6 Sq.mm x 3 Core PVC Aluminium Cable

Boom Barrier for car: Electromechanical parking barrier with all accessories upto 6 meter length

Supplying, installation, testing and Commission of Bollard Die cast aluminium housing, opal white PC diffuser, IP54 with in-built LED complete with all accessories with necessary as required and as directed by the department. Bollard Die cast aluminium housing, opal white PC diffuser, IP54 ( LBLD01R305XW ) with in-built LED complete

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required Group A

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 A socket outlet

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 3 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 12 Module

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required Upto 450 mm sweep

Supplying and fixing following way, single pole and neutral,sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way , Double door

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required 63 A

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying, installation, testing and Commission of ALUMINIUM CABLE 3 CORE 6 SQMM complete with all accessories with necessary as required and as directed by the department.GLOSTER 6 Sq.mm x 3 Core PVC Aluminium Cable

Supplying, installation, testing and Commission of the following Exhaust Fan CRATIVE (exhaust fan) complete with all accessories with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department. Exhaust Fan CRATIVE (exhaust fan)

Supplying, installation, testing and Commission of the following indoor Decorative Recess mounted LED down lighter luminaries of model no- Philips DN296B 14W/1550 LM complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Philips/Jaquar / LT / Wipro make). 16W Led Recessed

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required Group A

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 5/6 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 15/16 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required3 pin 5/6 A socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 6 pin 15/16 A socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. As required

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required 3 Module (100mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required 6 Module (200mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required 12 Module (200mmX150mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 3 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 6 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 12 Module

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required Upto 450 mm sweep

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required 63 A

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supplying including fitting fixing of following A.C. 2 Model Starter in the existing 2 model Modular board necessary connection as approved by the Deptt.)as required complete and as directed by the Department.25 Amps 2 Module Starter.

Supplying with installation testing and commissioning of Hi - wall 3 Star rating non ducted splite type air conditioner Splite of the following capacity with cordless remot complete with copper pipe and electrical connection cable, as approved by the Deptt. Up to 5 m between thr room unit and outdoor unit as directed by the Deptt. (LG /Voltas/Carrier / Blustar/ Daikin make)

Supplying with fitting and fixing Voltage stabilizer of the following specification complete including making necessary connection as approved, specified and directed by the deptt. (SKYLAND / Vee-Dee / V GUARD / VERTEX/ INDO/ VENUS make)

Supplying installation testing and commissioning of Exhaust Fan CRATIVE (exhaust fan) as required 1.5 sq mm copper multstrand wire connection an as specified and directed by the Deptt.Orient/Usha/Cromton make

Supplying and fitting fixing of electric storage water heater [Geyser] ofVenus 25 liter 4 Star Water Heater Venus (Venus Splash Copper 25CU) including necessary connection etc. as required complete and as directed by the Department. Venus 25 liter 4 Star Water Heater Venus (Venus Splash Copper 25CU)

Supplying, installation, testing and Commission of the following indoor Decorative Recess mounted LED down lighter luminaries of model no- DN296B LED15S-6500PSU WH HSN code 9405 complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Philips/Jaquar / LT / Wipro make).

Supplying with fitting and fixing of Sony Smart Television Tv 43 Inch Smart TV (Android TV) complete including making necessary connection as approved, specified and directed by the deptt. Sony Smart Television Tv 43 Inch Smart TV (Android TV)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required Group A

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required 12 Module (200mmX150mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 12 Module

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required Upto 450 mm sweep

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required 63 A

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supplying, installation, testing and Commission of the following tube Light Philips 22 Watt/2200 lumen 6500 K LED Tubelight Philips (ECOLINK 22 Watt) Luminaire complete with all accessories with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Philips/Jaquar / LT / Wipro make).Philips 22 Watt/2200 lumen 6500 K LED Tubelight Philips (ECOLINK 22 Watt)

Puberun Real Estate Pvt. Ltd.