Loading
Loading…
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
₹14.8 Cr
EMD Value
₹8.9 L
Closing Date
6 Feb 2026, 3:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Yes (up to 2 members)
No
Two Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
120 days
Expenditure
Capital (Works)
TENDER
14 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual Turnover of V/N or 'V' whichever is less, where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of ''total contractual payments'' in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover.
The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender.
The similar nature of work as mentioned above means that the work of Permanent Way Work involving: - Track linking or Track relaying (CTR or TRR or TSR) or Linking / insertion / replacement of turnouts
41 conditions · 5 needing a document upload
Documents to be attached in Electronic Mode
Scanned copy/copies of proof(s) of Technical Eligibility Criteria as mentioned in Standard Technical Criteria
Scanned copy/copies of proof(s) of Financial Eligibility Criteria as mentioned in Standard Financial Criteria
Scanned copy of Statement of Completed Works in the Last Three Financial Years
Required documents in case of Proprietary Firm / Concern OR Partnership Firm OR Limited Company OR Joint Venture Firm as mentioned in Commercial Compliance (If Applicable and whichever is applicable)
Scanned copy of Test report of ballast and / or any other items (If Applicable) - For tenders consisting the item of ballast supply or any other item where test report is required to be submitted
CERTIFICATE TO BE SUBMITTED/ UPLOADED BY TENDERER ALONGWITH THE TENDER DOCUMENTS as per annexure V & V(A)
Detail of Bank and PAN(Mandate Form as per annexure XXII)
Certificate to prove the Financial Eligibility as given in Financial Eligibility Criteria. Any one of the following certificates will be accepted:
Copy of certificate from the employer / client
Audited balance sheet/Income Tax Returns certified by the Chartered Accountant for qualifying period. ( For the duration of qualifying period for which the balance sheet is not audited i.e., for pervious / current financial year, a certificate issued by Chartered Accountant indicating explicitly contract receipts details of various organizations (Name of organization, Agreement wise receipts etc.,) is to be enclosed along with the tender documents. The tenderers may note that CA's certificate alone without copies of Audited Balance sheets/Income Tax Returns will not be considered for evaluation).
Affidavit / Certificate in case of Proprietary Firm / Concern Next
Details of Partnership Deed (If applicable):
Copy of Current Partnership Deed (If applicable)
Copy of Registration Certificate for the current partnership deed in the prescribed form issued by the registrar of firms for the changes in the constitution of the partnership deed, if any (If applicable)
Original Special Power of Attorney (duly registered / notarised as per the prevailing law) (If applicable)
Details of Limited Company (If Applicable):
Copy of Memorandum of Association and Articles of Association of the Company (If applicable)
Copy of incorporation certificate of the Company (If Applicable)
Copy of certificate issued by Registrar of Companies in regard of change of name, if any (If Applicable)
Copy of General Power of Attorney / Original Special Power of Attorney (duly registered / notarised as per the prevailing law) (If Applicable)
Copies of complete documents establishing the Merger / De- Merger / conversion / Taking over / acquisition / Sale etc. of the Limited Company (If Applicable)
Copies of those Partnership / Joint Venture(s) Deeds covering the period from the date of commencement to the date of completion of the work for which credentials are submitted, mentioning the share of the limited company OR Copies of the experience certificates issued to the limited company mentioning the share of interest in that partnership/Joint venture(s) Deeds (If Applicable)
Details of Joint Venture Firm (If Applicable):
Copy of the Memorandum of Understanding of Joint Venture Firm (Joint Venture Agreement) as per Pro forma on a non-judicial stamp paper of appropriate value as per the stamp duty Act (If applicable)
Consent of all partners of the Partnership Firm to enter into the Joint Venture Agreement on a stamp paper of an appropriate value in original in case of Partnership Firm as a Partner of JV OR Copy of Board of Directors resolution certified by Company Secretary / Auditor / Competent Authority consenting agreeing for entering into Joint Venture Agreement in case of limited companies (If Applicable)
Copy of General Power of Attorney / Original Special Power of Attorney (duly registered / notarized as per the prevailing law) (If Applicable)
In case of members belonging to sole proprietary concern / firm partnership Firms / Limited Companies, additional documents, as applicable for these entities and as indicated in the tender document, should also be furnished (If Applicable)
Copies of those Partnership(s) / Joint Venture(s) Deeds covering the period from the date of commencement to the date of completion of the work for which credential / experience certificate is submitted, as the case may be, mentioning the share of the said member in the Joint Venture / Partnership should be submitted along with tender OR The copies of the experience certificate issued for the said member, the Joint Venture firm mentioning the share of interest in that Partnership / Joint Venture(s) Deeds (If Applicable)
Details of HUF / Society or any other type of organization / firm (If Applicable):
Documents in support of formation and registration (If Applicable)
Working instructions of the organization (If Applicable)
Copy of General Power of Attorney / Original Special Power of Attorney (duly registered / notarised as per the prevailing law) (If Applicable)
Test report of ballast and / or any other items (If Applicable)
Any other document considered necessary for evaluation of the offer (If Applicable)
Status of firm (Perform I)
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Mandatory list of items/Documents as per Proforma -IX
Laying and Linking of BG track for Main line, Loop / siding lines and Point & Crossing etc. in station/yards, Transportation of P. Way materials, dismantling of existing track, Welding of Rails, through Rail Renewal including supply & spreading of machine crushed stone ballast, Earthwork & Blanketing in embankment / cutting in formation and other incidental miscellaneous works at Ujjain yard in connection with; (1) Ujjain - Provision in Stabling line in NC yard in connection with Simhastha - 2028. (2) Provision of stabling line and relocation of PQRS siding in loco yard in connection with Simhastha - 2028.
IND-UJN-SIMHASTHA-01~WR
IND-UJN-SIMHASTHA-01
Open
Works - General
12 Months
Unknown (Unspecified Location)
₹0
₹8.9 L
6 Feb 2026
7 Jan 2026
23 Jan 2026
160 items across 5 schedules · ₹18,38,23,010.38 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | With 3 horizontal bamboo / balli members of minimum 50mm dia. spaced equally | RM | 500.00 | 444.77 | 2,22,385 |
| 2 | Joining with strong nylon rope in one cross and one horizontal pattern of minimum 5mm dia. | RM | 500.00 | 113.74 | 56,870 |
| 3 | For Through Rail Renewal work | TRM | 1150.00 | 48.05 | 55,257.5 |
| 4 | For Through Rail Renewal work | TRM | 1150.00 | 49.55 | 56,982.5 |
| 5 | For location of work involving deep screening (deep screening to be paid separately). | Each | 1950.00 | 203.97 | 3,97,741.5 |
| 6 | Lubrication of gauge face of rail on curves, cross overs, points & crossings, turn-in curves and at locations as required with contractor's grease graphite grade "O" IS 408 and as directed. | RM | 7460.00 | 5.45 | 40,657 |
| 7 | Rail section of 90R and below | Each | 520.00 | 90.32 | 46,966.4 |
| 8 | Rail section of 52Kg and above | Each | 350.00 | 108.38 | 37,933 |
| 9 | Under Conditions not requiring Traffic Block | Set | 2.00 | 7,261.43 | 14,522.86 |
| 10 | 1 in 8½ Turnout (Under Traffic Block) | Set | 9.00 | 36,162.9 | 3,25,466.1 |
| 11 | 1 in 12 Turnout (Under Traffic Block) | Set | 3.00 | 41,060.82 | 1,23,182.46 |
| 12 | 1 in 8½ Turnouts | Set | 8.00 | 50,042.52 | 4,00,340.16 |
| 13 | 1 in 12 Turnouts | Set | 6.00 | 57,694.19 | 3,46,165.14 |
| 14 | Derailing Switch | Set | 3.00 | 10,918.84 | 32,756.52 |
| 15 | 1 in 8½ Points & Crossing | Set | 4.00 | 14,360.08 | 57,440.32 |
| 16 | 1 in 12 Points & Crossing | Set | 4.00 | 19,545.93 | 78,183.72 |
| 17 | Depth of 250 mm below bottom of sleeper of Plain Track | TRM | 1500.00 | 443.92 | 6,65,880 |
| 18 | Lifting and packing for regrading the existing PSC sleeper track to required height / level in stages not exceeding 75mm or part thereof at a time, providing permissible ramp for the track, insertion of moorum / sand / stone ballast uniformly under the existing track and placing the same to safe approved gradient, gauge, cushion including levelling and one round of through packing to allow train movement at restricted speed of 30 kmph for a specified length with all leads & lifts and fixing, marking, painting rail level pegs at every 30m interval. Note: Lifting of track shall be done in stages as per procedure prescribed in latest edition of IRPWM to get the proposed final level as per approved working profile, as directed by Engineer in-charge. | TRM | 2200.00 | 191.65 | 4,21,630 |
| 19 | Extra for additional lift over 75mm for every 50mm lift or part thereof up to 275mm for item nos. 083010 for each TRM. | TRM | 1500.00 | 29.7 | 44,550 |
| 20 | Boxing and profiling of ballast as per procedure prescribed in latest edition of IRPWM including cess dressing on both sides of track. The work will include removing excess ballast from track and putting the same in crib and shoulder by leading to a maximum of 50m including crossing of track, deweeding on ballast section etc and as directed by Engineer-In charge. | TRM | 9500.00 | 28.14 | 2,67,330 |
| 21 | Removing, screening and salvaging ballast from track, duly digging / scarifying ballast by beaters / wire brushes or any mechanical means, leveling and dressing formation with specified cross slope after salvaging ballast, separating muck by screening the salvaged ballast with contractor's 20mm size sieve, stacking of screened ballast for measurement, disposing off muck at specified locations with all lead & lifts as directed by Engineer in-charge. Note: Payment shall be made for quantity of ballast stacked after screening of retrieved ballast from track. | cum | 800.00 | 331.46 | 2,65,168 |
| 22 | Loading Railway's ballast, collected at yard / depot into Railway's BOB / BKH / any other type of open wagon, using Mechanical Loader or any other method with all lead and lifts, as directed by Engineer in-charge. | cum | 1000.00 | 42.14 | 42,140 |
| 23 | Under Conditions not requiring Traffic Block: | cum | 1200.00 | 42.64 | 51,168 |
| 24 | When distance of nearest quarry is more than 10 km and up to 20 km | cum | 25763.73 | 951.91 | 2,45,24,752.22 |
| 25 | For 60 Kg - 90 UTS Rail | Each | 710.00 | 4,301.16 | 30,53,823.6 |
| 26 | For 60 Kg/60EI - R260 grade Rail | Each | 140.00 | 4,482.96 | 6,27,614.4 |
| 27 | For 52 Kg - 90/72 UTS Rail | Each | 30.00 | 4,206.45 | 1,26,193.5 |
| 28 | Dismantling of existing LWR/SWR track of any structure, removing rails, sleepers, fish plates, cutting of rails, segregation and stacking of released Rails, Sleepers and fitting at nominated location in countable manner within a free lead of 500m, levelling of ballast to correct profile for laying new track over it, all as per direction of Engineer-in-Charge. | TRM | 2688.51 | 205.23 | 5,51,762.91 |
| 29 | Rail length up to 13m - Under Traffic Block | RM | 1050.00 | 21.34 | 22,407 |
| 30 | For rails/panels of more than 40m length - Under Traffic | RM | 1500.00 | 46.35 | 69,525 |
| 31 | For rails/panels of more than 40m length - Under Conditions not requiring Traffic Block | RM | 1100.00 | 32.9 | 36,190 |
| 32 | With Rail pegs | Each | 100.00 | 148.58 | 14,858 |
| 33 | With Tie bar pegs | Each | 200.00 | 98.06 | 19,612 |
| 34 | Installation of reference points for track centre line in main and loop lines, in straight or curve portion, SRJ for turnouts, heel of crossing (HOC), locations of derailing switches, switch expansion joints etc. away from formation on firm ground at known offset with MS Angles of 50mmx50mmx5mm thick of length 1.80 m each, founded in concrete block of size 30cm x 30cm x 45cm of nominal mix 1:3:6, including painting to reference pegs with two coats of enamel paints on exposed surface, as directed by Engineer In charge. Note: Earth work and Cement concrete will be paid under relevant items. | Each | 150.00 | 851.61 | 1,27,741.5 |
| 35 | Spreading of ballast, from existing stacks available along formation on top or at c e s s , in required uniform thickness, compaction of ballast layer laid on new formation at all the locations with smooth wheeled power roller of 8-10 tonne capacity to sufficient number of passes to form consolidated ballast bed of approximately 250mm thickness to a width of 4m symmetrical to centre line of proposed track in correct line & level with all ascents & descents, as directed by Engineer in-charge. Note: Item is inclusive of (a) providing ramp for taking roller to formation and removing the same & making good formation after completion of work; (b) redistribution & leveling of excess ballast while rolling to obtain uniform plane cambered surface. | cum | 25950.00 | 48.51 | 12,58,834.5 |
| 36 | For sleeper density of 1540 sleepers per km | TRM | 6944.19 | 310.5 | 21,56,171 |
| 37 | Linking of track at level crossing locations as per RDSO drawings with any type of rail section and sleeper on prepared formation including leading free rails/welded panels available along the alignment on to formation, spreading of sleepers at specified spacing, squaring, placing of rails over sleepers and fixing rails to sleepers with all types of fittings and fastenings to correct gauge & alignment, excavating level crossing portion as necessary, fixing check rails to running rails, providing C.C blocks, chairs, anti corrosive painting to running rails and check rails, lubrication of fittings and fastenings with contractor's grease as per IRPWM standards with contractors labour, tools, consumables, with all lead, lifts etc. complete and raising, levelling and initial packing of track to make it fit for 30 kmph and meet other prerequisites prescribed in Indian Railway Track Machine Manual for deployment of Tamping Machine. Note: Rail cutting and hole drilling, if required, shall be paid separately under relevant item. | TRM | 35.00 | 480.31 | 16,810.85 |
| 38 | Linking of BG track (with guard rail ) over ballasted deck bridges with any type of rail section and PSC sleeper including leading free rails/welded panels available along the alignment on to bridge, leading and spreading all fittings and fastenings, leading & spreading of sleepers at specified spacing, squaring, placing of rails over sleepers and fixing rails & guard rails to sleepers with all types of fittings and fastenings to correct gauge & alignment, lubrication of fittings and fastenings with contractor's grease as per IRPWM standards with contractors labour, tools, consumables, with all lead, lifts etc. complete and raising, levelling and initial packing of track to make it fit for 30 kmph and meet other prerequisites prescribed in Indian Railway Track Machine Manual for deployment of Tamping Machine. Note: 1.Rail cutting and Hole drilling shall be paid separately. 2.Spreading of ballast and compaction shall be paid separately under relevant item. 3. This item shall be applicable only when track is with Guard Rail. Linking without guard rail be paid under relevant item for plain track linking. | TRM | 150.00 | 452.65 | 67,897.5 |
| 39 | Maximum Shifting / Slewing up to 1 metre | TRM | 1505.58 | 221.24 | 3,33,094.52 |
| 40 | For PSC sleeper Track with Sleeper Density of 1540 Sleepers/Km or more | TRM | 7200.00 | 111.67 | 8,04,024 |
| 41 | For PSC Sleeper | TRM | 3450.00 | 95.71 | 3,30,199.5 |
| 42 | For PSC Sleeper Track with Sleeper Density of 1540 | TRM | 8150.00 | 134 | 10,92,100 |
| 43 | 1 in 8½ PSC layout | Set | 4.00 | 12,240.79 | 48,963.16 |
| 44 | 1 in 12 PSC layout | Set | 4.00 | 15,946.88 | 63,787.52 |
| 45 | For rails up to 13 metre length | TRM | 2500.00 | 38.61 | 96,525 |
| 46 | For rail panel above 13 metre & up to 40 metre length | TRM | 2500.00 | 42.51 | 1,06,275 |
| 47 | For rail panel more than 40 metre length | TRM | 1000.00 | 46.4 | 46,400 |
| 48 | With 2 bolts | Set | 40.00 | 117.37 | 4,694.8 |
| 49 | With Clamps | Set | 40.00 | 166.97 | 6,678.8 |
| 50 | For 60 Kg Rails | RM | 9000.00 | 95.59 | 8,60,310 |
| 51 | 1 in 12 Turnout | Set | 6.00 | 1,497.63 | 8,985.78 |
| 52 | 1 in 8½ Turnout | Set | 8.00 | 982.15 | 7,857.2 |
| 53 | Derailing Switch | Set | 3.00 | 491.08 | 1,473.24 |
| 54 | Curve Post | Each | 20.00 | 118.41 | 2,368.2 |
| 55 | Curve details, SE, Versine, Station Nos. etc. per station. | Each | 180.00 | 63.61 | 11,449.8 |
| 56 | New Line Section, not opened for traffic | TRM | 17900.00 | 11.05 | 1,97,795 |
| 57 | 1 in 8½ Turnouts | Set | 24.00 | 5,998.04 | 1,43,952.96 |
| 58 | 1 in 12 Turnouts | Set | 18.00 | 6,983.51 | 1,25,703.18 |
| 59 | Derailing Switch | Set | 9.00 | 2,193.25 | 19,739.25 |
| 60 | BCM/FRM/UNIMAT (7.5 KVA generator and 12x500 W) | Night | 10.00 | 5,082.83 | 50,828.3 |
| 61 | CSM / DUO / 3X with or without DGS (7.5 KVA generator and 8x500 W) | Night | 10.00 | 4,601.17 | 46,011.7 |
| 62 | 60 Kg - 110/90 UTS - Outside Track | Each | 2550.00 | 242.54 | 6,18,477 |
| 63 | 52 Kg - 90 UTS - Outside Track | Each | 60.00 | 219.77 | 13,186.2 |
| 64 | 52 Kg - 72 UTS & other rails - Outside Track | Each | 50.00 | 134.22 | 6,711 |
| 65 | 60 Kg - 110/90 UTS - On Running Line | Each | 60.00 | 310.82 | 18,649.2 |
| 66 | 52 Kg - 90 UTS- On Running Line | Each | 80.00 | 252.81 | 20,224.8 |
| 67 | Outside Track | Each | 7600.00 | 61.48 | 4,67,248 |
| 68 | On Running Line | Each | 300.00 | 78.7 | 23,610 |
| 69 | During period of traffic block | MT | 130.00 | 31.32 | 4,071.6 |
| 70 | Not involving traffic block | MT | 120.00 | 26.2 | 3,144 |
| 71 | From DMT - During period of traffic block | MT | 200.00 | 178.18 | 35,636 |
| 72 | Fabrication including cutting, bending/machining and fixing of check rails of all rail sections over PSC Sleepers as per Railway's approved drawings & specifications for level crossings / trolley paths/inspection lines in yards duly cutting rail flanges, wherever required to correct alignment and level, drilling of holes with machine in check rails and fixing to Running rail and sleepers with all Railway's fittings, e.g. rail screws / grip expansion bolts, brackets, packing pieces, bolts, washers etc including grinding of brackets if required, fixing of Railway's wooden blocks at flare ends duly cutting and plaining, crossing of tracks and as directed by the engineer in-charge Note: 1. Drilling of holes in PSC Sleeper and fixing of dowels shall be paid under relevant item. 2. Required P.Way materials will be supplied at SSE/P.Way stores. | TRM | 35.00 | 1,218.23 | 42,638.05 |
| 73 | With Contractor's hard wood block | Each | 14.00 | 1,632.15 | 22,850.1 |
| 74 | Manufacture of flared portion of Guard Rail by cutting and bending to required shape & RDSO's approved drawings. N o t e : (1) Rails shall be supplied by Railways. (2) One set consists of two rails i.e. both left and right. | Set | 6.00 | 4,798.73 | 28,792.38 |
| 75 | Providing and fixing of flared portion of guard rails of any rail section over PSC sleepers including fixing of with all fittings, including leading of rails and fittings, squaring and adjusting spacing of sleepers as required, providing nose blocks duly cutting wooden blocks supplied by railways and fixing it with bolts of 16mm dia as directed complete a n d finished as per RDSO's approved drawing. Note: 1.One set consists of LH & RH side rails of one end. 2.Required P.Way fittings will be supplied at SSE stores depot. | Set | 6.00 | 3,922.16 | 23,532.96 |
| 76 | Caution Indicator Board of size 1400mmx400mm with back support frame fixed to vertical post of MS angle of size 50mmx50mmx6mm of 3650 mm long | Each | 2.00 | 6,908.11 | 13,816.22 |
| 77 | Speed Indicator Board of equilateral triangular shape having each side of 1000mm with back support frame fixed to vertical post of MS angle of size 50mmx50mmx6mm of 3650 mm long | Each | 8.00 | 5,917.1 | 47,336.8 |
| 78 | Stop Indicator Board of size 1400mmx400mm with back support frame fixed to vertical post of MS angle of size 50mmx50mmx6mm of 3650 mm long | Each | 10.00 | 6,908.11 | 69,081.1 |
| 79 | Termination Indicator Board of Circular shape having diameter of 1000mm with back support frame welded to vertical post of MS angle of size 50mmx50mmx6mm of 3950 mm long | Each | 2.00 | 8,361.59 | 16,723.18 |
| 80 | Manufacturing, supplying and fixing Curve Indicator / Point Indicator / SEJ Boards to be provided at various locations on formation, made out of MS sheet 2mm thick of size 450mm x 300mm duly fixed with MS frame of 25mm x 25mm x 3mm angle welded to 50mm x 50mm x 3mm MS angle, 1000mm long post split and bent 100mm at bottom end with all lead & lift as per specification and including painting of details with enamel paint, as directed by Engineer in-charge (Earthwork & concreting will be paid separately) | Each | 10.00 | 1,171.89 | 11,718.9 |
| 81 | Boards with single post | Each | 20.00 | 644.57 | 12,891.4 |
| 82 | Boards with two posts | Each | 15.00 | 885.4 | 13,281 |
| 83 | For erection | Each | 5.00 | 272.4 | 1,362 |
| 84 | For removal | Each | 5.00 | 223.3 | 1,116.5 |
| 85 | Supply and fixing in position pre-cast cement concrete Fouling Mark as per approved drawing at station yard, duly painting the top surface and slopes with white enamel paint in two coats and inscribed letters with black of Fouling Mark, complete in all respects with all labour, materials including cement, tools and plants etc. | Each | 10.00 | 525.14 | 5,251.4 |
| 86 | Fixing vertically the unserviceable PSC sleepers at locations of tress-passing, railway boundary or to make temporary store by excavating trench, fixing PSC sleeper in trench and filling back open trench. | Each | 80.00 | 161.09 | 12,887.2 |
| 87 | JCB Backhoe Loaders 3DX Plus or similar with minimum 1.10 cum bucket capacity | Hour | 650.00 | 846.09 | 5,49,958.5 |
| 88 | Hydra or similar tyre mounted Pick-n- Carry crane of 12T capacity for misc. works of handling of material | Hour | 280.00 | 2,118.4 | 5,93,152 |
| 89 | Tractor with Trolley for local transportation or other misc. works. | Hour | 320.00 | 599.84 | 1,91,948.8 |
| 90 | Arranging labour as and when required by the Engineer in charge, for various works under SSE/P.Way, with contractor's T&P, equipments, hand signal flags, etc. as per specifications, special conditions and detailed scope of work as furnished in the tender and as directed by the Engineer in charge. Note: Item shall be operated with prior approval of concerned Sr. DEN / DEN in charge. | Day | 6000.00 | 753.26 | 45,19,560 |
| 91 | Manufacturing and fixing buffer stop with Railway supplied rails, cutting, including bending of rails as per plan ,with all contractor's labour, materials, tools, plants etc. and all lead and lift including crossing of track where necessary and as directed by Engineer in charge at site. Note: Excavation, fixing rails in cement concrete, drilling of holes will be paid separately. | Each | 10.00 | 18,844.36 | 1,88,443.6 |
| Schedule total | ₹4,87,11,426.96 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .