ADDN/ALTN TO JCO/OR MD ACCN AT Sri Ganganagar MIL STN

Amount

B/R PORTION

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4 Sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge.

Taking down wooden shutters only of any description area exceeding 1.0 sqm and not exceeding 2.0 sqm each andnd removing from site complete all as specified and as directed by Engineer-in- charge.

Taking down wooden shutters only of any description area exceeding 1.0 sqm and not exceeding 2.0 sqm each and refixing in same opening after necessary easing, adjustments, minor repairs, oiling, adjustment with cutting or fixing plain fillets/planks made from second class hard wood etc to remove gap between floor and shutter complete all as specified and as directed by Engineer-in- charge.

Supply and fixing second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing factory made pressed steel frames of size 125 x 60mm (thickness of sheet shall be 1.25mm) for doors with one or more rebates including necessary lugs and lock strike plate, etc. , including fixing only butt hinges suitable Nos as directed for each leaf, and making good the wall with plaster in CM 1:6 complete all as specified and as directed by Engineer-in- charge. Note : - Butt hinges shall be measured and paid separately under appropriate item of BOQ as supply only.

Supply and fixing factory made pressed steel frames of size 105 x 60mm (thickness of sheet shall be 1.25mm) for doors with one or more rebates including necessary lugs and lock strike plate, etc. , including fixing only butt hinges suitable Nos as directed for each leaf, and making good the wall with plaster in CM 1:6 complete all as specified and as directed by Engineer-in- charge. Note : - Butt hinges shall be measured and paid separately under appropriate item of BOQ as supply only.

Supply & fixing Factory made prefabricated Pressed steel Door frame made out of mild steel 1.25mm thick girth of frame 185mm including necessary MS rawl plug/bolts and fixing 75mm long butt hinges medium weight cold rolled mild steel etc and shutter including stiffeners made out of mild steel sheet 1.25mm thick cut to size, holes punched and welded seams including bending or turning up all around, mitred angle etc as required with Locking arrangement using mild steel mortise lock 4 levers with 2 Nos of keys of size 100mm (Make Godrej/Harison/Navtal) including MS chromium plated handle and 2 Nos MS locking rods out of 8 mm dia not exc 1000mm long fixed to mortise lock and handle with necessary bolts and nuts covered by MS sheet 1.25 mm thick complete including two coat of synthetic enamel paint over a shop coat of zinc chromate primer on interior surface (not -visible from front) and hammer tone paint on exterior surface ( visible from front) as per Godrej Pattern complete all as specified and as directed by Engineer-in-charge.

Material and labour for PCC (1:3:6) type C-1, using 20 mm graded aggregated as in back filling of pressed steel door frame/chowkhat and bed block for fixing of hold fast complete all as specified and as directed by Engineer-in-Charge

Supply & fixing factory made plain framed panelled shutter 35mm thick made out of 2nd class hard wood with lock rail and panel (two panels) inserts of 9mm BWP commercial ply. The size of rails and styles as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in- charge.

Supply & fixing factory made glazed and skeleton shutter 35mm thick made out of 2nd class hard wood kiln seasoned and chemically pressure treated, open rebated and prepared to receive glass, gauze, etc., but divided into squares, with plain chamfered or rounded, mitred and rebated sash bars, any numbers, fitted with cut and mitred beads for securing glass, gauze etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); complete all as specified and as directed by Engineer-in- charge.

Supply and fixing plain fillets or beading of sectional area not exc 3 sqcm made from second class hard wood square, rectangular or trangular in section, clean sawn, se-cured with nails or brads for securing wiremesh or similar works put together with glue pinned at joints complete all as specified & directed by Engineer-in- charge.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out 5mm thick plain clour PVC sheet reinforced with MS square tube including painting of edges to match with sheet, all as specified & shown in relevant drawing of item No. 8095 in MES Schedule SSR-2010 (Part-II), fixed in opening complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,door to be fixed to frame with and including 3 Nos MS powder coated butt hinges of size 100mm long x 25mm wide and 2mm thick and fixing with 32mm long steel screws drilled suitable to pass through both the walls of the MS tube complete all as specified in SSR-2009 (Part-I, specifications) & shown in relevant drawing of item No. 8080 in SSR-2010 (Part-II, rates). The width of stiles & rails will be in proportion to the width of the door shutter as specified in SSR-2010 (Part-II). complete all as specified and as directed by Engineer-in-Charge.

Supply only 100mm long MS butt hinges heavy duty type B-21 including stainless steel screws complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement 100mm long MS butt hinges heavy duty type B-21 including stainless steel screws complete all as specified and as directed by Engineer-in-charge.

Supply and fixing anodised aluminium handle cast type 150mm long complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement anodised aluminium handle cast type 150mm long complete all as specified and as directed by Engineer-in-charge.

Supply and fixing aluminium anodised barrel tower bolt of extruded section, 200mm long complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement aluminium anodised barrel tower bolt of extruded section, 200mm long complete all as specified and as directed by Engineer-in-charge.

Supply & fixing aluminium anodised sliding door bolts 250mm long, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in replacement aluminium anodised sliding door bolts 300mm long, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed by Engineer-in- charge.

Supply and fixing helical door spring of size 150mm complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement helical door spring of size 150mm complete all as specified and as directed by Engineer-in-charge.

Supply & fixing Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles of 2nd class hardwood n exc 200 cu. cm each complete all as specified and as directed by Engineer-in- charge.

Supply & fixing Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, Overall length of cover plate 150mm, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Hasp and staple, safety type, brass with aluminium anodised 100 mm size, hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed by Engineer-in-charge.

Material and labour for preparation of new steel and iron surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in- charge.

Material and labour for Preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in- charge.

Material and labour for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using sanded paper, clean cloths and dry paint brush & applying two coats of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossing finish with using paint brush complete as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using clean cloths and dry paint brush & applying two coats of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossing finish with using paint brush complete as specified and as directed by Engineer-in-Charge.

Dismantling of boarding any description fixed in any position with nails/screws complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing 18mm thick Plywood, grade BWR, type BB, fixed with screws to frame work along with one side laminate and other side plain white 0.9mm thick type-I, colour pattern as approved including PVC lipping, PVC sheet is heat bent as lipping on the edges of doors complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 25 mm size magnetic catchers with plastic body and striking plate including letting in and fixed complete all as specified and as directed by Engineer-in-charge.

Supply & fixing Continuous (piano) hinges, stainless steel, bright finish or electro galvanised, width of flap when open 30mm complete all as specified and as directed by Engineer-in-charge .

Cutting holes in brick walls built in cement mortar, exc half brick but n.exc one brick including making good dismantled portion in CM (1:3) or cement concrete (1:2:4) type B-1 complete all as specified and directed by Engineer-in-Charge.

Cutting openings, through brick walls built in cement mortar for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exc. 50m complete all as specified and directed by Engineer-in-Charge.

Supply & fixing aluminium anodised frame, made out of aluminium section powder coated (minimum thickness of powder coating not less than 50 micron) for window, ventilators and aluminium partition with one or more rebates including joining cleat for fixing etc., the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawal plug and screw or with fixing clip or with expansion hold plate fasteners. Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required complete all as specified and as directed by Engineer-in-Charge. Note :- The weight of each section shall be physically ascertained through a board of officers convened by GE and payment shall be made only after the actual weight at site.

Supply & fixing anodised aluminium window shutter (glazed or gauzed), side hung type without sash bars, made out of aluminium section weighing not less than 0.55 Kg/mtr, powder coated (minimum thickness of powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings (each shutter) such as peg stays 150mm long (1 No), hinges type B-21 100mm long (2 Nos) suitable handle (1 No.), complete all as specified and as directed by Engineer-in-Charge. Note :- Aluminium chowkhat/ frame, Glass and wiremesh shall be measured and paid separately under appropriate item of BOQ.

Supply & fixing anodised aluminium ventilator fixed type with frame, made out of aluminium section weighing not less than 0.55 Kg/mtr, powder coated (minimum thickness of powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws etc complete all as specified and as directed by Engineer-in-Charge. Note :- Glass shall be measured and paid separately under appropriate item of BOQ.

Supply & fixing Eye door viewer (magic eye) of size 25mm dia fixed in position for door shutters complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing Rubber sheet 50mm wide and of thickeness not less than 3mm fixed with stainless steel screws at the bottom of the door shutters complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed complete all as specified and as directed by Engineer-in- charge

Supply & fixing in replacement Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed complete all as specified and as directed by Engineer-in- charge

Supply & fixing 4mm thick sheet glass ordinary quality in squares / retangular not exceeding 0.5sqm in each pane (aluminium window/ventilator) complete all as specified and as directed by Engineer-in- charge. Note :- Aluminium fittings and rubber beading for securing the glass shall be included in main item of aluminium window/ventilator of BOQ.

Supply & fixing, 4mm thick figured glass pin head type in squares / retangular not exceeding 0.5sqm in each pane complete all as specified and as directed by Engineer-in- charge. Note :- Aluminium fittings and rubber beading for securing the glass shall be included in main item of aluminium window/ventilator of BOQ.

Material and labour for mild steel Framed work such as grills, ladder, cooler stand, cloth drying provision, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe.290.Gde-E-165 including dismantling old seel any description complete all as specified and as directed by Engineer-in- charge.

Roughening surfaces of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust etc. complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Non Skid ceramic light coloured tiles 7 to 8 mm thick square area of each tile 600mmx600mm, as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed bed) in cement mortar (1:6) and finish the surface rough to receive the tile complete all as specified and directed by Engineer-in-Charge.

Material and labour for Non Skid ceramic light coloured tiles 7 to 8mm thick square or rectangular as in skirting (cut from same size and type as floor tile ), dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 10 mm thick bedding layer (rendering) in cement mortar (1:4) and finish the surface rough to receive the tile including making good plaster surfaces (above skirting tile) to match the existing complete all as specified and as directed by Engineer-in-Charge.

Demolition of floor hearth or wall tilling including cement mortar bedding but not backing including removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Non Skid ceramic light coloured tiles 7 to 8 mm thick square or rectangular area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed bed) in cement mortar (1:6) and finish the surface rough to receive the tile complete all as specified and directed by Engineer-in-Charge.

Material and labour for Glazed ceramic coloured tiles light shade of size 300mmx 450mm, 7mm thick, as in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 10 mm thick bedding layer (rendering) in cement mortar (1:4) and finish the surface rough to receive the tile complete all as specified and as directed by Engineer-in-Charge.

Dismantling of Stone slabs of any description or thickness in floors, plateform, apron etc laid bedded and pointed in any mortar including removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge.

Material and labour 18-20mm thickness approved shade granite of minimum size equal to width of slab (not less than 610mm) machine cut, granite duly factory grinding and polishing and chamfering the outer edges (table rubbed and mirror polished) as in cooking platform and like laid over and including 25mm thick cement mortar (1:4) screed bed including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including accomodate the hole for gas pipe complete all as specified and as directed by Engineer-in-Charge.

Material and labour for machine cut 20 to 25 mm thick, Kota stone slab (size of slab not less than 550x450mm for flooring and in single piece for treads of staircase), laid over and including 20 mm thick bedding layer in cement mortar (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing /grinding (mirror finish) and polishing by machine, including machine cutting to make it square or rectangular as per site complete all as specified and as directed by Engineer-in-Charge.

Material and labour for machine cut 18mm thick, Kota stone slab as in skirting, dado and on pillar, laid over and including 10 mm thick bedding layer in cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing /grinding (mirror finish ) and polishing by machine, including machine cutting to make it square or rectangular complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided including removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge

Material and labour for water proofing treatment to sunken slab and adjoining vertical surfaces as per any one of the two method as specified in PSS-II clause No 9 on Page 169 of CA complete all as directed by Engineer-in-charge/GE. Note : (i) Work shall be executed through specialized agency (ii) The treatment shall be carried out as per the manufactures instructions and as directed by the Engineer in charge. The name of firm shall be got approved from CWE before carrying out the work. (iii) Only Plan area will be measured for payment. Treatment should be continue upto 450mm height on vertical walls. (iv) PCC filling under sunken area will be measured & paid separately.

Material & Labour for PCC (1:5:10) type E2 using 40mm graded stone aggregate as filling of sunken floors complete all as specified and as directed by Engineer-in-charge.

Material & Labour for 40 mm GI pipe medium grade, made to shape as in spout pipe 60cm long in sunken/ verandah/ Balcony including making hole and making good with cement mortar complete all as specified and as directed by Engineer-in-charge.

Dismantling brick terracing tiles single layer from roof laid and pointed in cement mortar and removing/disposal off from the site complete all as specified and as directed by Engineer-in-charge.

Demolition/taking out of mud from roofs, any thickness, including removing / cutting uprooting grass, vegetations and roots of small plants etc on roof and surrounding/parapit wall etc, including removing rubbish material from building and thrown in low lying empty area (as per direcction of AGE) at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge

Material and labour for Preparing surface of screed on roof and cleaned of all dust, loose particle etc , sprinkling water on the surface and ensure water does not stand anywhere. If it is so, the roof surface shall be leveled than surface shall be painted with one coat of cold applied bituminous primer @ 0.40 ltr per sqm, applied over primed surface APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by forced application, torching with overlaps as recommended by the manufacturer complete all as specified and as directed by Engineer-in-charge.

Material and labour for PCC ( 1:3:6), type C-1 using 20 mm graded stone aggregate as in roof padding complete all as specified and as directed by Engineer-in-charge.

Material and labour for PCC (1:2:4) Type B0 using 12.5mm graded stone aggregate as in roof kerb (golla) or mud stops & similar work etc rounded or chamfered on edges including necessary form work etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for Cement concrete tiles 25cm x 25cm x 20mm thick, with grey cement & no pigment, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished including screed 15mm thick in cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge.

Demolition of cement concrete (unreinforced) in ground floor and paving not exceeding 15cm thickness below or above ground level of any description and in any position including removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge

Material and labour for 75 mm thick PCC (1:3:6) type C-2 using 40mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement including 10mm wide, 30mm deep joints at the rate of 3.00 mtr centre to centre and at every turning point, filling the Joints with bitumen 7 sand mixture complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for repair of facia using cement mortar (1:3) n.exc 300 mm girth finishing the surface even and smooth complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 25 mm thick PCC (1:2:4) Type B-1 using 25mm graded as in floor finished fair & even etc complete all as specified and directed by Engineer-in-Charge.

Taking up or down existing galvanised steel water tubing (GI pipe) 15mm bore including fitting/connection from wall, ceiling, floor etc. complete all as specified and as directed by Engineer-in-charge.

Re-fixing old serviceable 15mm bore galvanised steel water tubing (GI pipe) including all fittings in new or old portion/position to walls, ceiling, floor etc complete all as specified and as directed by Engineer-in-charge. (Note :- Old serviceable pipe and fittings obtained from taking up or down (here-in-before) item of this BOQ shall be reused after necessary cleaning internally and rerunning the old screw threads as required.

Supply and fixing galvanized steel tubing (GI pipe) medium grade 15mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling or laid in floor including cutting and threading of pipe complete all as specified and as directed by Engineer-in- charge.

Taking up or down existing galvanised steel water tubing (GI pipe) 20mm bore including fitting/connection from wall, ceiling, floor etc. complete all as specified and as directed by Engineer-in-charge.

Re-fixing old serviceable 20mm bore galvanised steel water tubing (GI pipe) including all fittings in new or old portion/position to walls, ceiling, floor etc complete all as specified and as directed by Engineer-in-charge. (Note :- Old serviceable pipe and fittings obtained from taking up or down (here-in-before) item of this BOQ shall be reused after necessary cleaning internally and rerunning the old screw threads as required.

Supply and fixing galvanized steel tubing (GI pipe) medium grade 20mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling or laid in floor including cutting and threading of pipe complete all as specified and as directed by Engineer-in- charge. Note :- Cutting chases if required same shall be measured and paid separately under appropriate item of BOQ.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 in brick walls to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed by Engineer-in- charge.

Material and labour for reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in platform (slab) of water tanks on roof, supported on walls complete all as specified and as directed by Engineer-in-Charge. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Supply & fixing rotational moulded polyethylene water storage tank white colour of capacity 500 litres (cylindrical vertical, triple layered with closed top), hoisted and fixed in position including making inlet and out let connection including dismantling/taking down of existing unserviceable PVC water storage tanks of any description and capicity with float valve and gate valve complete all as specified and as directed by Engineer-in-charge.

Disconnecting existing serviceable PVC tanks (OHT) of capacity upto 500 litre, setting aside (or lowering if required) for repairs, cleaning , etc. and hoisting if required reconnecting and re-fixing in original position including all inlet and outlet water connection (as per existing) after removing all scale and dirt from tanks and from mouths of circulating pipes including screwed down old float valve and gate valve complete all as specified and as directed by Engineer-in-charge.

Supply and fixing ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball (polythene float) complete, screwed suitable for 20mm bore iron pipe complete all specified and as directed by Engineer-in-charge. Note :- The minimum weight of ball valve shall be as given in SSR or in relevant IS.

Supply and fixing gun metal, globe or gate valve (ISI marked), with iron wheel head, screwed both ends suitable for 20mm bore iron pipes complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of gate valve shall be as given in SSR or in relevant IS.

Supply and fixing in replacement bib tap cast copper alloy, chromium plated, fancy type with capstan head or round head knob, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply and fixing in replacement concealed stop cock cast copper alloy, chromium plated, fancy type, long shank and cup, screwed both ends suitable for 15mm bore iron pipe complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of stop valve/stop cock shall be as given in SSR or in relevant IS.

Supply and fixing in replacement 15 mm bore chromium plated Angle stop valve of cast copper alloy chromium plated, fancy type screwed down high pressure with on/off handle screwed end for iron pipe or for unions and fixed complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply and fixing brass chromium plated mixer valve 15mm bore, for mixing hot & cold water, complete with fittings for WHB including taking out any type pillar cock/tap complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply & fixing in replacement 450 mm long PVC connection 15mm size with PTMT nuts complete all as specified & directed by Engineer-in-charge.

Supply and fixing in replacement Kitchen Rack / Dish Rack (Kitchen Stand or wall mounted) of size 750mmx600mmx250mm (Appx size) made out of Food Grade Stainless Steel 1mm thick sheet/strip including necessary arrangements for plates and utencils to keep (Holds up to many plates or bowls To accommodate several place settings, Multipurpose), stylish modern streamline design, rust resistant, easy to assemble and clean including fitting accessories complete all as directed by Engineer-in-charge.

Taking down carefully Kitchen Rack / Dish Rack (wall mounted) and refixing after repair to building work including fixing/hanging material as required complete all as directed by Engineer-in-charge.

Supply & fixing in replacement stainless steel sink with drainage board made out of 1.00mm thick sheet , kitchen or laboratory with plugs, washers, waste pipe including bedding in cement mortar to dwarf wall or fixing cast iron cantilever brackets and connecting union to waste pipe; overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm including taking down existing chinaware sink complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement vitreous china wash basin, white, flat back of size 550mm x 400mm, including 32mm chromium plated waste coupling and PVC waste pipe including bracket and cutting for and pinning in end of bracket or erecting with long screwed shanks & fly-nuts, flange end bedded in red lead cement complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing in replacement corner vitreous china wash basin, white, flat back of size 450mm x 390mm, including 32mm chromium plated waste coupling and PVC waste pipe including bracket and cutting for and pinning in end of bracket or erecting with long screwed shanks & fly-nuts, flange end bedded in red lead cement complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed along wall with chromium plated catcher brackets, brass screws and PVC plug complete all as directed by Engineer-in-charge.

Supply & fixing in replacement vitreous China squatting pan 'Orissa' pattern white of size 580mmx440mm white with integral foot rests, excluding flushing cistern, flush pipe above floor but including setting the trap and pan in lime concrete (1 lime, 2 sand or surkhi and 5 aggretate), min. 150mm thick all round and finished just below level of rim of pan to receive the floor finishing, including PVC flush pipe upto finished floor level, joints of flush pipe and trap make leakproof and testing upto entire satisfaction of Engineer-in-charge before filling concrete complete all as specified and as directed by Engineer-in- charge.

Supply and fixing in replacement PVC low level cistern of 10 ltrs capacity with top push button inclusive of brackets and PVC bend long type and connection to flush pipe of any size and pattern with inlet ball valve float and handle complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement brass cromium plated shower rose 125mm size, with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed by Engineer-in-charge.

Supply & fixing in replacement brass chromium plated tubular towel rail 20mm dia 'D' type, 600mm long between flanges fixed to plug , bracket with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge.

Supply and fixing chromium plated soap tray any type, including fixing to wall with CP screws and PVC plug complete all as specified and directed by Engineer-in-Charge.

Supply and fixing corner glass shelf assembly fancy type, made of 5mm thick sheet toughened glass of size 250x250mm, fixed along wall with chromium plated catcher brackets, brass screws and PVC plug complete all as directed by Engineer-in-charge.

Taking down eaves gutters and rain water PVC pipes ( any size or pattern) including all fittings, heads, shoes, bends, swan-neck etc ( measured overall as fixed along the centre line over fittings and accessories) complete as specified and as directed by Engineer-in- charge

Supply & fixing 110mm bore PVC (SWR) pipes single socketed (pressure rating not less than 4kg/sqcm) in any length with rubber ring joints for drain or rain water fixed along walls with and including PVC stack clamps (interval of 1m) of suitable size, complete all as specified and as directed by Engineer-in- charge.

Supply & fixing PVC (SWR) bends (any radius) suitable for 110mm bore pipe complete all as specified and as directed by Engineer-in- charge.

Supply and fixing curtain rod 25mm dia MS pipe with coloured PVC coated, wall thickness of pipe not less than 20 guage, including fancy type brackets and pair of decorated end knobs (finials), stop roller etc. as per site requirement, fixed to wall with fixing accessories, including taking down old existing curtain rods any description complete all as specified and as directed by Engineer-in-Charge.

Dismantling/taking up or down CI soil waste and vent pipe 100mm dia of any description from wall and taking out from trenches including all fittings (bend, trap, cowl, branch piece etc) and removing from the site complete all as directed by Engr-in-Charge.

Dismantling/taking up or down CI soil waste and vent pipe upto 75mm dia of any description from wall and taking out from trenches including all fittings (bend, trap, cowl, branch piece etc) and removing from the site complete all as directed by Engr-in-Charge.

Supply and fixing 100mm bore cast iron soil waste and vent pipe (sand cast pipe) in any length with or without ears, fixed to wall with and including MS stack clamps (interval of 1m), nut and bolts of suitable size and securing ends of stays to wall and including PCC work for grouting, all joints filled with and including lead, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 75mm bore cast iron soil waste and vent pipe (sand cast pipe) in any length with or without ears, fixed to wall with and including MS stack clamps (interval of 1m), nut and bolts of suitable size and securing ends of stays to wall and including PCC work for grouting, all joints filled with and including lead, complete all as specified and as directed by Engineer-in-charge.

Supply & fixing 100mm bore cast iron Bends (any radius) with duck's foot or heel rest complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 75mm bore cast iron Bends (any radius) with duck's foot or heel rest complete all as specified and as directed by Engineer-in- charge.

Supply and fixing in repair 75mm dia of long neck CI floor trap, with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) using 20mm graded stone aggregate complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 100mm bore CI branch pieces single (equal or unequal), ordinary or inverted (Spigot or socket type) with oval access door complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 75mm bore CI branch pieces single (equal or unequal), ordinary or inverted (Spigot or socket type) or with parallel branch fitted with oval access door complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and as directed by Engineer-in- charge.

Supply and fixing 150mm x 150mm size salt glazed stone ware gully traps, square or round mouthed, type 'P' complete all as specified and as directed by Engineer-in- charge.

Supply and fixing 100mm cast iron sanitary connection socket to fit WC out-let complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 100mm bore cast iron cowl complete all as specified and as directed by Engineer-in- charge.

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundations, shafts, wells, cess pits, manholes, for taking out old pipe and laying new pipe line, for laying cable etc. not exceeding 10 Sqm on plan and getting out in soft/loose soil including trimming the sides and forming bottom surfaces to required levels complete all as specified and as directed by Engineer-in-charge.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and as directed.

Removing excavated material (surplus soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed by Engineer-in-charge.

Material and labour for cement concrete (1:3:6), type C-2 using 40mm graded stone aggregate as in bed of drain pipe of size 150mm bore (internal) including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed by Engineer-in- charge.

Material and labour for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 150 mm dia of pipe complete all as specified and directed by Engineer-in-Charge. (Note : Excavation, earth work and concrete bed shall be measured and paid separately under appropriate item of BOQ.)

Taking down cement or cement lime plaster from brick wall etc including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for internal plastering 15mm thick in cement mortar (1:6) on any face of Brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rendering/plastering 15mm thick on any face of Brick wall or concrete surfaces consisting in two layers i.e. first layer 10mm thick in cement mortar (1:4) and second (top layer) layer 5mm thick in cement mortar (1:4) including mixing of liquid WPC in mortar @ as per manufacturer instruction per bag of cement of 50kg, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. (Note :- WPC shall be measured & paid separately as Supply only)

Material and labour for rendering/plastering 5mm thick in cement mortar (1:3) on any face of ceiling in patches not exceeding 3Sqm each patch, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Supply only liquid water proofing compound complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Preparation of new plastered Internal wall surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:- (a) Applying Wall care putty in two coats on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed. (b) Two coats of acrylic distemper over a coat of primer by using paint brush / Roller.

Material and labour for Preparation of new plastered external wall surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:- (a) Applying Wall care putty in two coats on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed. (b) Two coats of exterior acrylic emulsion of approved tint over a coat of acrylic emulsion external primer by using paint brush / Roller.

Material and labour for Preparation of new plastered or concrete surface of ceiling surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:- (a) Three coats of white wash by using paint brush.

Material and labour for complete removal of existing treatment on Old Internal wall surfaces of any desciption, preperation of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:- (a) Applying Wall care putty in two coats 1.5 mm thick each for filling to depression of scraped surface/nail holes/light cracks etc and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed. (b) Two coats of acrylic emulsion of approved tint over a coat of primer on old prepared surface by using paint brush / Roller. Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible.

Material and labour for Preparation of new plastered or concrete surface of wall by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:- (a) Three coats of white wash by using paint brush.

Material and labour for complete removal of existing treatment on Old external wall surfaces of any desciption, preperation of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology, complete all as specified and as directed by Engineer-in- charge and applying the following:- (a) Applying Wall care putty in two coats 1.5 mm thick each for filling to depression of scraped surface/nail holes/light cracks etc and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed. (b) Two coats of exterior acrylic emulsion of approved tint over a coat of acrylic emulsion external primer on old prepared surface by using paint brush / Roller. Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible.

Material and labour for Preparation of old decorated surfaces (plastered/unplastered) of walls/pillars /cornices by remove / scraping down all smoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom / steel patti / wire brush / sand papering or by any other mean including applying wall care putty where required for filling to depressions/nail holes/light cracks etc and to make surface even and smooth, and after preparing the surface smooth applying two coats of lime white wash with paint brush complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Obliterating old writing of any description, not exceeding 0.1 Sqm, with paint to match existing work etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Writing letters or figures (Block. Roman, Italic or Indian) n exc. 30 cm high complete all as specified and directed by Engineer-in-Charge.

Material and labour for applying one coats of Dr Fixit pidecrete URP in chajja, staircase etc by using 2 Sqm per 1 Kg URP + cement in the proportion of (1:1.5) and making pedicrete solution and applying by brush complete as specified and as directed by Engineer-in-Charge.

Material and labour for 40mm thick precast cement concrete (1:3:6) type C-0 using 12.5mm graded stone aggregate as in louvers and jallies (measured solid) including all moulding but excluding frame and set in cement mortar (1:4) including necessary form work complete all as specified and directed by Engineer-in-Charge.

Material and labour for 50mm Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ cm2 laid in trenches complete all as specified and directed by Engineer-in-Charge.

Dismantling of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, in any description including cleaning and stacking serviceable brick for re use and balance removing rubbish from the site complete all as specified and as directed by Engineer-in-charge.

Material and labour for brick work with sub class ‘B’ old size burnt clay bricks, straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge.

Material and labour for brick work in half brick thick wall straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge.

Material and labour for preparation of new plastered surfaces of walls/pillars /cornices by brooming down with using broom/sand papering or by any other mean, washing down with water and applying two coats of cement base paint as per approved tint/colour with using paint brush complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing Stainless steel solid body fancy type peg set of six and fixed in position with steel screws complete all as specified and as directed by Engineer-in-Charge.

Material and labour for running welding in repairs thickness of metal to be welded will be exc 9 mm but not exc 20mm complete all as specified and as directed by Engineer-in-Charge.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/ loose soil including cutting of grass, roots, bushes if any and filling of lower portion with soil obtained from cutting and dressing complete all as specified and as directed by Engineer-in-charge.

Removing excavated material (surplus soil) to a distance not exceeding 5 KM and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed by Engineer-in-charge.

Material and labour for 75 mm thick PCC ( 1:4:8), type D-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and as directed by Engineer-in-charge.

Supply and laying/fixing 60 mm thick (M35 grade) precast interlocking tile/paving block factory casted (made by using PVC/ Rubber moulds on Vibrating Table Machine) using grey cement and pigment, prepolished & preglazed, shape haxagon / trigular / zigzag / I-shaped etc, as directed, confirming to relevant IS, having compressive strength not less than 350 Kg/ Sqcm, laid over and including 25mm thick layer of sand cushining and filling the interstices etc with sand complete all as specified and as directed.

Supply and laying factory made kerb stone of M-25 grade cement concrete laid in position to the required line, level and curvature, jointed with cement mortar (1:3) (1 cement:3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and as directed.

Material and labour for GI wire netting 0.90mm dia and 12mm mesh lathing by means of fasteners of required length and spacing between fasreners is 300 mm centre to centre both ways to concrete surface etc in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste complete all as specified and as directed..

Material and labour for mild steel ISMB, Joist, channel, angle, or tee sections, fixed adjacent to ceiling and embedding in floor and brickwork including cutting welding , without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) FE 410 W(GdeE-250) quality 'A' complete all as specified and as directed..

Demolition of cement concrete reinforced of any description such as kitchen chimeny, chajjas, shelves, OHT etc, including reinforcement cut as required to facilitate demolition and prepare the surface to casting/jointing new including removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge

Material and labour for reinforced cement concrete M-25 (Design mix) using 20mm graded stone aggregate as in slabs supported on walls, beams and columns landing, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engineer-in-Charge. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and labour for reinforced cement concrete M-25 (Design mix) using 20mm graded stone aggregate as Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed by Engineer-in-Charge. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and labour for reinforced cement concrete M-25 (Design mix) using 20mm graded stone aggregate as in chajjas complete all as specified and as directed by Engineer-in-Charge. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and labour for mild steel TMT bars 10mm dia & over cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.)

Material and labour for mild steel TMT bars 6 to 8 mm dia cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.)

Form work to soffits of suspended slabs such as flat roof slabs, floor slabs, shelf slab, landings and similar work not exceeding 200mm thick (horizontal or sloping) rough finished complete all as specified and as directed by Engineer-in- charge.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough finished complete all as specified and as directed by Engineer-in- charge.

Form work to chullah hoods, chajjas, troughs and similar items including edges rough finished complete all as specified and as directed by Engineer-in- charge.

Form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide rough finished complete all as specified and as directed by Engineer-in- charge.

Shotcreting average thickness 25mm in RCC columns, beams and slab etc. (with mix minimum cement content of 350 Kg per Cum, M-25). Concrete having the specified minimum characteristic compressive strength (with ordinary portland cement, coarse sand and graded stone aggregates of 6mm to 10mm size in proportion as per design criteria) incl the cost of centering and shuttering at edges and corner etc as directed by Engr-in-Charge incl chipping of unsound/week concrete material 25mm average thickness from slabs, beams/columns etc with mannual Chisel or standard power driven percussion type all of approved makes incl tapering of all edges, making square shoulder of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes and throughly washing with water and allowing it to dry etc incl removel of rust by applying approved rust remover chemical and the coating with Dr Fixit Epoxy zinc primer @ 6 Sqm per Litre at DFT of 100 micron as per manufacturer's instruction and specification, including removing rubbish material from building and thrown in low lying empty area at any distance from the site as directed complete as specified and as directed by Engineer-in-Charge. Make :- Sika / Fosroc/Pidilite or Techno commercial equivalent make approved by GE in writing from E-in-C's approved list. Note : Complete treatment to be executed by approved applicator.

Supply and fixing hard drawn steel wire fabric not exc 4kg/sqm cut to lengths, wire mesh to be fixed and firmly anchored to the concrete surface by means of 'L' shaped mild steel shear key welded with existing reinforcement including cost of material, labour, tools and plants incl welding/L-clip/tying with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

Drilling Holes of 12mm dia up to 100 mm deep holes in structural members at the interval of 300 mm in staggered manner or along the crack line in Reinforced Concrete (RC) structural element including cleaning of the holes by air blower and inserting 12mm dia NRV (Non Returnable Valve) nozzle compatible with epoxy injector and having machined external end to receive outlet of Grouting Gun. Fix inside the hole by applying thixotropic epoxy adhesive to ensure complete sealing and allow curing the system for minimum of 8 Hrs before Grouting including nozzle projections, excess putty, if any, over concrete element by grinding, leveling and finishing the external surface, after completion of the work, etc. complete all as specified and as directed by Engineer-in-charge.

Grouting, injecting two part, low viscosity, moisture insensitive injection liquid, based on high strength epoxy resin by pressure and using pressure epoxy injector with accessories till nozzle refused to accept the grout including mixing of grout having following properties:- (i) Mixed Density 1.1 kg/l (at +27°C); Viscosity ~ 250 mPas at +30°C and should comply according to ASTM C 881, Type II and IV, Grade-1, Class E+F (ii) Compressive strength >= 70 N/sqmm (7 days) according to ASTM C 579; Tensile Strength ~ 50 N/sqmm (after 7 days at +30°C cure) (According to ASTM D 638); Tensile Modulus ~ 2000 N/sqmm (after 7 days at +30°C cure) (According to ASTM D 638); (iii) Bond Strength ~ 10.8 N/sqmm (failure in concrete) after 14 days at +30°C cure; Flexural strength ~ 50 N/sqmm according to ISO 178. (iv) Seal the nozzle with thixotropic epoxy adhesive after the refusal of grout material from the nozzle. Note:- leakage through other nozzle or cracks are required to be monitored while grouting and such points to be sealed as and when required without any extra cost complete all as specified and as directed by Engineer-in-charge. Note :- Mode of measurement: per kg of material consumed Make: Sika - SikaDur 52 LP/ Fosroc- Conbextra EP 10/ Pidilite Dr Fixit Epoxy Injection Grout or equivalent make approved by GE in writing from E-in-Cs Br approved list.

EM PORTION

Taking down carefully existing copper/aluminium point wiring (light/fan/sockets/bell/power point) complete with all accessories such as switch socket with sheet, ceiling rose, lamp holder including rusted/broken concealed conduit, junction and sunken boxes etc and removing dismantled material and making good disturbed surface of walls/floors etc matching with existing surface complete all as specified and as directed by Engineer-in-Charge.

Material and labour for concealed Point wiring for one light point/fan point controlled by one switch (using red, black and green colour wires as colour coding) complete with 1.5 Sqmm (nominal cross section area) single core FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through and including PVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction box, 2mm thick galvanised steel pressed sunken terminal boxes of suitable size (Min 60mm deep, suitable length) concealed in wall, 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket / regulator etc, including provn of 1.5 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3) complete all as specified and as directed. (switches, regulator shall be measured and paid separately under appropriate item of BOQ).

All as per above Srl item No. 171 but for one socket out let 5 Amps point controlled by one switch (on same board) complete all as specified and as directed by Engineer-in-charge. (switches, sockets etc. shall be measured and paid separately under appropriate item of BOQ).

All as per above Srl item No. 171 but for one socket out let 5 Amps point controlled by one switch (on independent board and not below the any other switch board) complete all as specified and as directed by Engineer-in-charge. (switches , sockets etc. shall be measured and paid separately under appropriate item of BOQ).

All as per above Srl item No. 171 but for call bell point complete all as specified and as directed by Engineer-in-charge. (switches , sockets etc. shall be measured and paid separately under appropriate item of BOQ).

Material and labour for concealed Point wiring for one light point controlled by two Nos- two way switch (using red, black and green colour wires as colour coding) complete with 1.5 Sqmm (nominal cross section area) single core FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through and including PVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction box, 2mm thick galvanised steel pressed sunken terminal boxes of suitable size (Min 60mm deep, suitable length) concealed in wall, 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switch, including provn of 1.5 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3) complete all as specified and as directed. (switches shall be measured and paid separately under appropriate item of BOQ).

Material and labour for concealed Point wiring for one socket out let 15/16 Amps point controlled by one switch (on independant board) (using red, black and green colour wires as colour coding) complete with 2.5 Sqmm (nominal cross section area) single core FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through and including PVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction box, 2mm thick galvanised steel pressed sunken terminal boxes of suitable size (Min 60mm deep, suitable length) concealed in wall, 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket, including provn of 2.5 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3) complete all as specified and as directed. (switch, socket shall be measured and paid separately under appropriate item of BOQ).

Material and labour for concealed Point wiring for one socket metal clad plug and socket with 4 Sqmm (nominal cross section area) single core FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through and including PVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction box, including provn of 4 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3) complete all as specified and as directed. (Single pole and neutral enclosure with socket plug complete shall be measured and paid separately under appropriate item of BOQ).

Supply and fixing switch piano flush type (ISI marked) , 5/6Amps, single pole, one way fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. Note ;- Laminated sheet shall be measured and paid in point wiring item of BOQ.

Supply and fixing switch piano flush type (ISI marked), 5/6Amps, single pole, two way fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. (laminated sheet and covering frame shall be included in point wiring item of BOQ).

Supply and fixing switch piano flush type (ISI marked), Bell Push, 5Amps, single pole, one way fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. (Laminated sheet shall be measured and paid in point wiring item of BOQ).

Supply and fixing Socket outlet multipurpose type (ISI marked), 2 in 1, 3 pin, 5/6 Amp, flush type fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. (Laminated sheet shall be measured and paid in point wiring item of BOQ).

Supply and fixing Socket outlet multipurpose type (ISI marked), 2 in 1, 6/5 pin, 6 amp and 16 amp, flush type fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. (Laminated sheet shall be measured and paid in point wiring item of BOQ).

Supply and fixing switch piano flush type (ISI marked), 15/16Amps, single pole, one way complete all as specified and as directed by Engineer-in-charge. (Laminated sheet shall be measured and paid in point wiring item of BOQ).

Supply and fixing ceiling rose (ISI marked) surface type polycarbonate isolated body two to three terminal, topline series 20x50mm, 6 Amp, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing angle Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings

Supply and fixing stepped type (1-4/5), electronic Fan regulator (one module), 100-120 watt, 250 volts, fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. (Laminated sheet shall be measured and paid in point wiring item of BOQ).

Supply and fixing electric calling Bell Ding Dong type, AC 230 Volts single pole including making elctric connection and testing, complete all as specified and as directed by Engr-in-charge.

Supply and fixing switch piano flush type (ISI marked), 25Amps (for AC point), single pole, one way complete all as specified and as directed by Engineer-in-charge. Make :- Cat part No 6759-68 of legrand or Techno commercial equivalent in make mentioned in Appx 'B' (Laminated sheet shall be measured and paid in point wiring item of BOQ).

Supply and fixing MCB ‘B’ curve suitable for 240 volts AC supply, 06 to 32 Amps, SP with over load and short circuit protection and rupturing capacity not less than 10 KA, fixing in DB/panel complete all as specified and as directed by Engineer-in-charge

Supply and fixing MCB ‘B’ curve suitable for 240 volts AC supply, 32-40 Amps, SPN with over load and short circuit protection and rupturing capacity not less than 10 KA, fixing in DB/panel complete all as specified and as directed by Engineer-in-charge

Supply and fixing MCCB of capacity 63 Amp, TPN, 415 volt, short circuit breaking capacity 16KA , thermal magnetic trip, setting 80-100%, Icu-100% Ics, fixing in DB/panel complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement (concealed flush to wall) factory made DB (made out of CRCA sheet not less than 1.2mm thick, fitted with DIN channel neutral link and 200 Amp rated bus bar) SPN, 12 Way 240V, suitable for mounting MCB/Isolator, conforming to IS-13032, DB shall be semi glosy finished with epoxy polyster based powder paint sprayed and backed at high temperature between powder paint process to ensure smooth finish and protection against corrosion atmosphere. The DB shall be double door type with hinged door with locking arrangement, the DBs shall be same make as MCBs, DB shall be provided with level marking indicating the incoming and outgoing circuits on always as specified. The DBs shall be of IP-43 protection class, including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-charge. Note :- MCB’s shall be measured and paid separately under appropriate item of BOQ.

Supply and fixing in replacement (fixing in panel board) factory made DB (made out of CRCA sheet not less than 1.2mm thick, fitted with DIN channel neutral link and 250 Amp rated bus bar) VTPN, 4 Way, suitable for mounting MCCB/MCB, conforming to IS-13032, DB shall be semi glosy finished with epoxy polyster based powder paint sprayed and backed at high temperature between powder paint process to ensure smooth finish and protection against corrosion atmosphere. The DB shall be double door type with hinged door with locking arrangement, the DBs shall be same make as MCBs, DB shall be provided with level marking indicating the incoming and outgoing circuits on always as specified. The DBs shall be of IP-42 protection class, including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-charge. Note :- MCCB/MCB shall be measured and paid separately under appropriate item of BOQ.

Supply and fixing in replacement LED complete fitting including batten, T-8 Retro LED polycarbonate 1 x 20 Watt, appx 4 feet long, environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to tube fitting, complete fitting with all accessories and following specifications, including taking down old Unserviceable light fitting any type complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts. (c) Temp operating range : Minus 10°C to Plus 45°C (d) Power factor : Minimum 0.95 (e) THD : Max10%. (f) IP rating : IP-20. (g) CRCA pre coated housing with two coloured plastic end cap. (h) LED Driver of the same make as of the luminaire. (j) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection minimum 2.5 kV. (l) CCT : 6500K (m) CRI : Morethan 80 (n) Rated life time : 50000 burning hrs (Average 10 to 12 hrs daily)

Disconnecting electric connection and taking down carefully serviceable LED tube light and keep in safe custudy. After the building repair work or as directed refixing including electric connection with and including new flexible copper wire 3 core , including new nut bolts and split pins etc complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement complete set of 1x10 watt LED retrofit type bulkhead fitting luminaries die cast aluminium alloy body heat resistant prismatic glass cover with specially designed gasket lamp holder etc complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete fitting with all accessories and following specifications, including taking down old Unserviceable light fitting any type complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 45°C (d) Power factor : Minimum 0.95 (e) THD : Max 10%. (f) IP rating : IP-20. (g) CCT : 6500K (h) Pressure die cast Aluminium housing (j) LED Driver of the same make as of the luminaire. (k) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (l) Surge protection minimum 2.5 kV. (m) CRI : Morethan 80 (n) Rated life time : 50000 burning hrs (Average 10 to 12 hrs daily)

Supply and fixing in replacement LED light fitting 1 x 10 Watt, appx 2 feet long environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to light fitting, complete fitting with all accessories and following specifications, including taking down old Unserviceable light fitting any type complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 45°C (d) Power factor : Minimum 0.95 (e) THD : Max 10%. (f) IP rating : IP-20. (g) CRCA pre coated housing with two coloured plastic end cap. (h) LED Driver of the same make as of the luminaire. (j) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection minimum 2.5 kV. (l) CCT : 6500K (m) CRI : More than 80 (n) Rated life time : 50000 burning hrs (Average 10 to 12 hrs daily)

Supply and fixing LED lamp minimum 3 star rated 9W LED B-22 base complete all as specified and directed by Engr-in-Charge with following specifications (a) Lumen system efficacy of lamp should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 45°C (d) Power factor : Minimum 0.95 (e) CRI : Morethan 80

Supply and fixing in replacement energy efficient LED street light fitting of 25W pressure die cast aluminium housing/body, heat resistant clear toughened glass, better optics for uniform distribution street/Roadway luminaire, with driver, including electric connection, fixing the light fitting with new bracket made out of GI tubing light grade 32mm dia, 1.2 metre long bent to shape at 120 degree angle at half metre from bottom, including two Nos clamps made out of MS Flat iron size 40x3 mm with suitable nuts and bolts for fixing of bracket including painting to MS clamp and nut bolts with two coats of aluminium paint over a coat of red oxide primer, complete fitting with all accessories and following specifications, including taking down old Unserviceable light fitting with old bracket any type complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : Max10%. (f) IP rating : IP66. (g) IK rating : Minimum IK07 (h) Built in potted LED Driver of the make as of the luminaire. (j) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection 10 kV (inbuilt + extended) (l) CCT : 5700 K. (m) CRI : Morethan 80 (n) Lens - High Efficiency wide angle lens. (o) BIS Approved fixtures and driver (p) Rated life time : 50000 burning hrs (Average 10 to 12 hrs daily)

Supply and hanging /fixing ceiling fan 1200 mm sweep AC Supply (Input Voltage Range ; 120 to 280V), BLDC type, 5 star rated, BEE and ISI Marked super enamelled, copper winding of 'B' class insulation, single phase, minimum 30W (± 10%), Temperature rise 40 degree maximum without remote with and including capacitive regulator, 03 No blades, down rod including accessories, white colour, total harmonic less than 10%, 5 speed, hanging in position including making connection with flexible cord three core twisted copper conductor of suitable size from ceiling rose to fan complete all as specified. Note :- (i) Serial Number as issued by Engr-In-Charge of celing fan and GE Office name shall also be written on fan with red colour permanent marker and fixing of regulator on switch board, cost for the same shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account

Supply and fixing exhaust fan (heavy duty) steel body, AC single Phase 230V, 50 Cycle per second, size 300mm sweep with blades and frame including self closing GI louvers off mode protection against birds etc mounted in suitable opening arrangement. including electric connection with and including new flexible sheathed copper wire of size 24/0.2mm, 3 core from ceiling rose to fan (not exceeding 0.5 mtr long), and hanging on wall with 4 Nos steel fastners 10mm dia 100mm long and making good the disturbed surface complete all as specified and as directed by Engineer-in-charge. Note :- Serial Number of exhaust fan issued by Engr-In-Charge and GE Office name shall also be written on fan with red colour permanent marker.

Supply and fixing ventilating Air Fan of size 200mm sweep, made of sturdy Engineering plastic complete with louvers and 5 Nos blade, fitted in suitable opening arrangement and connecting up with and including three core PVC Insulated PVC Sheathed copper conductor flexible cable, including fixing material and making good the disturbed surface complete all as specified and as directed by Engineer-in-charge.

Material and labour for concealed sub main wiring (Two run for main i.e. phase and netural and one run for continues as earth wire connected to earth dolly etc., using red, black and green colour wires as colour coding) with 6 Sqmm single core, FRLSH PVC insulated multistrand copper conductor drawn through and including PVC conduit 20mm dia (medium quality ISI marked), on independent circuit from DB including all fitting arrangement i.e. PVC clamp, rawl plug, screw, terminal/junction box, tee, bend etc. and including cutting of chases in wall, taking out old sub main wiring of any conductor any size from conduit and taking down old unserviceable conduit with fittings, and making good disturbed surfaces of walls as per original complete all as specified and as directed by Engineer-in-charge. Note :-Three run of 4 sqmm copper wire and one run conduit shall be measured as one RM length for payment.

Disconnecting electric connection and taking down carefully serviceable ceiling fans and keep in safe custudy. After the building repair work or as directed refixing /hanging the ceiling fan including electric connection with and including new flexible sheathed copper wire 3 core from ceiling rose/connector to fan connector, including in replacement new nut bolts, rubber reel, capacitor 2.5mfd, machine screws and split pins etc including painting the ceiling fan complete body with blades, canopies, down rod etc. with synthetic enamel paint by spray gun after scraping down old paint in colour as directed complete all as specified and as directed by Engineer-in-charge. Note :- Serial Number of celing fan issued by Engr-In-Charge and GE Office name shall also be written on fan with red colour permanent marker.

Disconnecting electric connection and taking down carefully serviceable Exhaust Fan and keep in safe custudy. After the building repair work or as directed refixing the Exhaust Fan including electric connection with and including new flexible sheathed copper wire of size 24/0.2mm, 3 core from ceiling rose to fan (not exceeding 0.5 mtr long), fixed in replacement by using new 4 Nos nuts & bolts and washers grouted in wall in CM (1:3) and new self closing GI louvers off mode protection against birds etc, including painting the exhaust fan complete body with blades etc. in colour as directed with synthetic enamel paint by spray gun after scraping down old paint complete all as specified and as directed by Engineer-in-charge. Note :- Serial Number of exhaust fan issued by Engr-In-Charge and GE Office name shall also be written on fan with red colour permanent marker.

Disconnecting electric connection and taking down carefully serviceable geyser any capacity and keep in safe custudy. After the building repair work or as directed refixing /hanging the same including making all water connection with in replacement new PVC connection 15mm bore 450mm long with PTMT nut both side suitable for hot and cold water, including electric connection with and including three core PVC Insulated PVC Sheathed copper conductor flexible cable, 04 No Nut bolts grouting in wall in PCC (1:2:4) using 12.5mm graded stone aggregate for hanging the geyser and making good the disturbed surface complete all as specified and as directed by Engineer-in-charge.

Supply, installation, commissioning and testing of factory made LT panel Board (main control board) of minimum size 0.9 x 0.9 x 0.25mtr fixed on/inside wall (front side open-able glass double door including locking arrangements and handle), dust proof, vermin proof made out of CRCA sheet 2 mm thick powder coated, Suitable size for fixing electronic energy meter-04 Nos and VTPN DB box with incoming cable and out going sub-main wiring and internal wiring with & including single core, PVC copper conductor unsheathed wire multistanded 4 sqmm and with proper spacing including provision of rubber beading and mild steel cable glands and lugs, provision of air fins for ventilation, complete including all connections incoming / out going, including taking down old panel board any type with fittings complete all as directed by Engineer-in-charge. Note :- Electronic meter and VTPN DB shall be measured and paid separately under appropriate item of BOQ.

Taking down old serviceable electronic/electric meter single phase and keep in safe custudy. After the building repair work or as directed refixing the same complete with accessories in LT panel box complete all as specified and directed by Engr-in-Charge.

Supply, installation, connecting and testing energy efficient (BEE 5 Star Rating) electric water heater (Geyser) ABS body, vertical storage type, capacity 25 litre, stainless steel tank, brass assembly, pressure release valve, heating element 1500 watt, all other accessories with high quality external finishes, single phase, working voltage 230/ 240 volt, 50 Hz, ISI marked all as directed by the Engineer- in-Charge. Note:- The cost of fixing of geyser with & including stud/ nuts/ fastener, bolt, washers and making good the disturbed surface to match with existing surface is inclusive in unit rate quoted. Make : V guard (victo plus 25 L)/ Bajaj ( shakti Neo 25 L)/ Havells ( Monza DX 25L)

Supply and fixing PVC flexible15 mm size pipe connecting suitable size with PTMT nuts bth side of length 450mm complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement and testing Junction box flush mounted of size 100mm x 100mm x 100 mm having holes for 20 mm dia conduit entry including 2 pin TV socket outlet flush type duly marked with symbol of TV and 3 mm thick plastic laminated sheet cover compl;ete for TV connection complete all as specified.

Supply and fixing Rigid non-metallic PVC conduit 20 mm dia exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and directed by Engineer-in-Charge.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground ( earth pit not less than 2.25 mtr deep below normal round level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanized earth lead GI Strip of size 32 x 6 mm by means of GI bolts/nuts/washers, protected by 50 mm bore GI medium grade pipe from earth plate & upto 3 m long pole fixed with 2 clamp made from mild steel flat iron 32 x 6 mm bolts, nuts, washer etc. earth plate shall be surrounded by alternate layer of charcoal or coke and common salt 15 cm thick all around bottom and top of earth plate 40 mm thick RCC cover PCC 1:2:4 type C-1 using 20 mm graded stone aggregate reinforced with XPM ( weight not less than 4 gm/ sqmm) and frame of angle iron 25mm x 25mm x 6 mm with 02 Nos and with 6 mm dia MS bar handle made to shape, 20 mm GI Medium grade pipe for watering and including funnel, wire mesh, in earthing pit including necessary excavation & earth work, including disconnecting existing earthing all as specified & shown on electrical plate No 3 of SSR Part - I. Note : (i) PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge.

Supply and laying or fixing or laid in trenches / ducts / through pipes / in floors / under roads / under hard standing /along poles and testing, Cross linked Polyethylene (XLPE) LT Cable, XLPE Insulated, PVC inner sheathed, bedded, galvanised steel strip or wire armoured cable (heavy duty) 1100 volt grade with stranded aluminium conductor having cross sectional area 25 Sqmm 4 core conforming to IS-7098 (Part-I)-1988 with upto date amendments, including taking out old unserviceable cable any size complete all as specified and as directed. Note :- (i) Excavation, earth work, sand cushioning, brick protection, boring/cutting of road and pipe shall be measured & paid separately under appropriate item of this Schedule.)

Material and labour for sand cushioning, with dry and clean fine river sand (for under ground cable) 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cable complete all as specified and as directed. (Note:- Punned thickness shall be considered for payment purpose)

Supply and laying un-reinforced precast concrete cable cover, class LV, type 2 flat, size 300mm x 180mm x 40mm for cable protection cover, laid dry in trenches over the cable , perpendicular to the direction of cable complete all as specified and as directed.

Supply and fixing in replacement GI tubing light grade of size 40 mm bore, ISI marked, fixed along poles/walls or laid in trenches, under road for cable protection including fittings (elbow, tee, socket etc) complete all as specified and as directed. (Note:- Excavation and earthwork as required shall be measured and paid separately under respective item of Sch.)

Material and labour for extra wiring for inverter socket out going to DB with 1.5 Sqmm single core, FRLSH PVC (using colour coding as directed) insulated multistrand copper conductor drawn through existing conduit (conduit for point wiring already catered in point wiring item of BOQ) including making connection to DB and inverter socket) complete all as specified and as directed by Engineer-in-charge.

Supply and fixing plug top 5/6Amp 3 pin good quality suitable for 240 volts, AC supply for inverter socket complete all as specified and as directed by Engineer-in-charge.

Supply and fixing socket outlet flush type (ISI marked), 25Amps (for inverter point), fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. (Laminated sheet shall be measured and paid in point wiring item of BOQ).

BHULLARCONSTRUCTIONS

SOM BUILDERS

M/s Kamal Builders

Aggarwal brothers and company

M/s MITTAL CONSTRUCTIONS

KHANNA CONSTRUCTIONS