SPECIAL REPAIR TO BUILDING NO T- 205 AND T- 207 INCLUDING CERTAIN MINOR WORKS OF ASC CENTRE (SOUTH) UNDER AGE B/R II IN GE (CENTRAL) BANGALORE

Amount

B/R PORTION: - Dismantling of Asbestos Cement Corrugated or Semi-corrugated sheeting, any gauge, thickness, in roof covering including ridges complete as directed. (measured flat overall)

Demolition of plain cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness. (below or above ground level) and removing debris outside MD land complete all as specified and directed.

Demolition of brick work, precast concrete block walling or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc and removing debris outside MD land complete all as specified and directed.

Demolition of plain cement concrete (unreinforced) any description and in any position not otherwise specifically provided for such as in roof/chajja padding etc complete including removing the materials out side MD land complete all as specified and directed.

Demolition of reinforced cement concrete any description and in any position not otherwise specifically provided for etc, cutting reinforcement steel to facilitate demolition of concrete including removing the materials out side MD land complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposing serviceable tiles to MES store and the rubbish/debrises out side MD land complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing debris outside MD landcomplete all as specified and directed

Taking down chowkats or frame, not exceeding 1.5 Sqm in each with shutters (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames, exceeding 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Taking up or down 20mm bore, Steel tubing and connections.

Taking up or down 25mm bore, Steel tubing and connections.

Dismantling of 2000 litre capacity PVC water tank for cleaning and repair and refixing in the same location/position including reconnecting all the pipe line complete all as directed.

Demolition and breaking up drain pipes of 100/75 mm dia(PVC/salt glazed ware, AC or reinforced concrete) set in cement mortar complete all as specified and directed.

M & L for surface excavation averaging 15cm deep and n.exc 30cm deep and getting out as in soft/loose soil including removing the soil to a distance exc 250M but not exc 500 M and depositing where directed complete all as specified and directed.

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr depth for laying of UG cable/GI/CI pipe lines etc getting out including forming bottom surface to required level and gradient in hard/dense soil.

Returning and filling in excavated soil including spreading leveling, watering, well ramming in layers not exc 25 cm thick complete.

Removing of surplus excavated materials to a distance not exceeding 50 Mtrs and depositing where directed by Engr- in-Charge at a level not exceeding 1.5 Mtrs above the starting point.

Supply and fixing RCC pipe, 150mm bore, class NP-3, laid and jointed with collar complete all as directed.

M & L for Plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggragate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore DWC/SGSW/RCC drain pipes complete all as specified and directed.

M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for moorum/sand/red bajri filling under floors or in foundations laid in layers n exc 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M & L for Hardcore of broken/crushed stone aggregate of gauge n.exc 63 mm deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for 150mm/100mm/75mm thick Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub-base of floor, etc complete all as specified and directed.

M & L for pressed steel frame of size 125mmX60 mm made out of 1.25mm thick plain black steel sheet for door with one or more rebates including fixing by welding necessary lugs, hinges, lock plate and PCC filling into frame using plain cement concrete 1:3:6, type C1 etc complete all as specified and directed. NOTE : - Butt hinges shall be measured and paid separately as supply only under respective item BOQ.

Providing and fixing factory made UPVC White colour Sliding window Three track made of extruded profiles with wall thickness of 2.2mm(±0.2mm). Window profile with hollow section with multi chamber. Frame (93mm x 52mm). Sliding Sash (42mm x 68mm). Sliding Mesh sash (22mm x 60mm) Sliding Interlock(One Vertical length in each shutter) (44.5mm x 34mm) Glazing bead (20.5mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2±0.2mm thick, galvanized steel Frame (28mm x 14mm) , sliding sash (32mm x 32mm) sliding mesh sash ((26mm x 12mm) profile to be inserted in required profile, frame will be fixed to the wall with 6mm x 75mm long fasteners Hardware -(TouchLock of zinc alloyed/aluminum (white powder coated), Nylon roller system. Stainless steel wire cloth 0.2mm nominal dia of wire and average width of aperture 1.01mm and required accessories.

M&L for 35 mm thick 2nd class hard wood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete, as specified and directed.

S & F powder coated aluminium (Minimum thickness of powder coating 50 micron) frame work and shutters for doors, windows, ventilators, including frame for partitions with extruded built up standard tubular section/appropriate Z section and other sections of approved make conforming to IS-733 and IS 1285 fixing with dash fasteners of required dia and size including necessary filling gaps at junction ie at top, bottom and sides with required EPDM rubber/neoprene gasket etc including providing and fixing hinges/ pivots. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat, angle, aluminium snap beading for glazing/ paneling, CP brass/ Stainless steel screws, rollers, handles, locking arrangement etc. complete all as specified. Note : (i) Glass panes and particle board will be measured and paid seperately. (ii) The quoted rate shall be inclusive of cost of rubber beading however it will not be weighed and not paid seperately. (iii) All other minor details including cost of locking arrangement shall deemed to be included in the quoted rate.

S & F solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet 5mm thick to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification and drawing shon in SSR Part II (2020 Print) and as directed.

Supply only 100 mm size, butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S & F 100 mm size, butt hinges, stainless steel with cadmium coated screws complete all as specified and directed.

S & F 150 mm long, Aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and directed.

S & F 125 mm size, Aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S&F in mild steel powder coated door stopper with hard drawn steel spring, 150mm size fixed to door all as directed.

S & F aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm anodised finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

Supply only 4 mm thick, sheet glass, ordinary quality and glazing with oil putty/timber beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Supply only 4 mm thick, sheet glass, pin head/figured glass and glazing with oil putty/timber beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for stainless steel wire cloth 0.24 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed

M & L for Mild steel framed work such as grills, gratings, door, gates etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S & F band, straps, supports or stays for rainwater pipes, ventilating pipes, including bolts if required hooks (stay), heavy duty, for large gate, hooks and pintle hinges, large hasp and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, wind ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and the similar small articles drilling holes for bolts etc conforming to Fe-290 Gde- E-165 all as directed.

S & F Rolled mild steel work as compound girders and stanchion, lattice girders , staging for water tanks and the like including caps, bases, splices etc built up from two or more beam or channel section or angles with plates including all lattices bars, stiffeners, gusset plate, cutting, welding complete. Steel section conforming to Fe-410-W (Gde-E-250) quality-B complete all as specified and directed.

S & F Rolled mild steel work as in trusses, purlins, rafter etc using Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc including distance pieces, cleats etc , cutting, welding complete. Steel section conforming to Fe-410-W (Gde-E-250) quality-B complete all as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating (AZ 150)GI based corrugated steel sheet 0.50mm thick (Total coated thickness) of any colour, finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with best quality self tapping screws as specified

S & F Pre-Painted galvalume aluminium zinc coating (AZ 150)GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutter, fixed with self tapping screws complete all as specified and directed. (Colour of ridge shall be same colour as that of sheet used for roof)

M&L 2mm thick fibre glass reinforced translucent corrugated sheeting matching with profile of galvalume sheet fixed with self tapping screws complete all as specified and as directed.

S & F for false ceiling of 4mm thick HSPC (High Presure Steam Cured) pre-primed self embossed texured designer ceiling board, cement fibre board of size 595X595 mm (E-Board Classic, white colour) to be fixed in and including GI snap grid with rool formed out of hot dip galvanised steel capings (Powder coated finished) 600X600 mm system. The suspension system consisting of perimeter wall angle of size 38X24X0.90mm of thick GI sheet to secure on wall portion fixed with the help of rawl plug @ 450mm centre to centre universal main runner of T shaped section with single rotary stitching of size (32X24X0.9 mm) made from 0.0.9mm thick GI sheet of length 3.60 metre to be spaced @ 1200 centre to centre cross runner T shaped with double rotary stitching of size (28.6X24X0.9 mm) of length 1200mm made from 0.90 mm thick GI sheet spaced @ 600mm centre to centre (1200X600mm) of size module intermadiate T shaped cross runner of size (28.6X24mm) of length 600mm made of 0.0.90mm thick GI sheet to form (600X600mm) size of module including suspension of the ceiling from the roof/structural members, soffits angles, cleats, by using GI suspenders of 3mm dia GI wire and level adjusters including U clamp of GI fixed in ceiling all complete and making opening by cut out the ceiling board for ceiling light fittings as required and as per manufacturer's instruction or as directed by Eng-in-charge. Make :- Eternit Everest / lafarge/ Armstrong or equivalent as approved by GE

M & L for 25 mm thick, plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in base of flooring, level course etc and finished the surface fair to receive top layer screed bed complete all as specified and directed.

M & L for non-skid, ceramic, joint free, matt finish, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for non-skid, ceramic, joint free, matt finish, coloured tiles 8 to 10mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for glazed ceramic, coloured tiles, 350x250x7mm thick/450X350X7 to 8mm thick as in skirting/dado/steps including 10 mm thick screed bed in cement mortar 1:3 set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for Plain cement concrete 1:5:10, type E-2 (using 40 mm graded stone aggregate) as in filling of sunken floor, foundation filling etc complete all as specified and directed.

M & L for Reinforced Cement Concrete M-25 nominal mix as in beams, cantilevers, lintel beam etc complete all as specified and directed.

M & L for Reinforced Cement Concrete M-25 nominal mix as in slabs supported on walls, beams and column in floors, roofs, landings, balconies and in shelves and the like complete all as specified and directed.

M & L for Reinforced Cement Concrete M-25 nominal mix as in chajjas etc complete all as specified and directed.

M & L for use & waste Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings, balconies and in shelves and the like for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste Form work to soffits and sides of beams, lintel beam for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste Form work to sides and soffits of concrete chajjas and the similar works for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection laid in proper slope/gradient etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

M & L for 100mm thick Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub base of floor, foot path etc complete all as specified and directed.

Cutting into existing manholes for inserting new drain pipe, 150mm bore and making good to pipe and rendering, cutting out existing benching for and forming branch channel in cement concrete 1:2:4 type B1 finished to match with existing complete all as directed.

M & L for Plain cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as surface channels and drains complete all as specified and directed.

M & L for precast chequered cement concrete tiles of size 30cm x 30cm x 25mm thick, as in floors etc, including 20 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and directed.

M&L for precast cement concrete block masonry type C1, 1:3:6 (20 mm graded granite stone aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M & L for precast cement concrete solid building blocks or slabs as in masonry, 10cm thick, type C1, 1:3:6 (20mm graded aggregate) set in cement mortar 1:4 complete all as specified and directed.

M & L for racking or cutting out joints and decayed mortar/ pointing to squared rubble stone masonry wall, coursed or uncoursed built in cement mortar not less than 12mm deep, washing the joints including cleaning properly by washing the joints and removing the rubbish off the premises, keeping the surface to be pointed wet for 2 days prior to re-pointing including raised pointing using cement mortar 1:4 complete all as directed.

M & L for Precast Reinforced Cement Concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in cover slab of drain, manhole etc and set in cement mortar 1:4 including necessary form work, moulds, etc complete all as specified and directed by the Engr-in-Charge. (Note : Reinforcement shall be measured and paid separately)

Providing cement concrete type B-1, 1:2:4 mix (using 20 graded stone aggregate) as in roof kerb, filling gap between roof sheet and wall and the like including necessary formwork.

S & F TMT steel bars 10mm dia and over, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F TMT steel bars 6 to 8mm dia, cut to length, bend to shape required, including cranking, bending spirally as in tie/stirrups of columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F TMT steel bars 6 to 8mm dia, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L Rendering 15mm thick on fair faces of brick masonry or concrete surfaces in CM 1:4 surface finished even and smooth without using extra cement complete all as specified and as directed.

M & L Rendering 15mm thick on other than fair faces of brick/concrete block masonry surfaces in CM 1:6 surface finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 15 mm thick in two layer (10mm + 5mm thick) on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with water proofing compound at top 5mm thick layer by weight of cement as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

M&L for rendering 10 mm thick cement mortar 1:4 on stone masonry surfaces or surfaces other than fair faces of brick work or on one side of lathing complete all as specified and as directed

"Supply only" integral water proofing compound (ISI marked) complete all as specified and directed. (Make : Dr FIXIT/Fosroc/choksey)

M & L for roof treatment by rendering 10mm thick in CM 1:4 mixed with water proofing compound by weight of cement as per manufacturer's instruction, applying oil bound bitumen primer @ 1.5 Kg/Sqm and providing 3 mm thick APP membrane weighing not less than 3.6 kg/sqm reinforced with non woven polyester matt weighing not less than 180 gm /sqm having softening point not less than 140 centigrade, having tensile strength of 650N/sqm and 350 N/sqm in longitudinal and transverse directions respectively of the reinforced tearing strength of 180N by torch application with minimum 10cm side overlap and 15cm end lap, applying a coat of blown grade hot bitumen 90/15 over the membrane @ 1.2 Kg /Sqm on top of membrane surface and then finished with solar reflective bituminious aluminium paint @ 0.10 Kg/Sqm complete all as specified and as directed. NOTE: - Water proofing compound shall be measured and paid separately under respective item.

M & L for preparing newly plastered surfaces of internal walls, etc and applying two coats of distemper oil emulsion over a coat of primer including 1mm to 2mm thick wall care putty complete all as specified and directed.

M & L for preparation external surfaces of wall, chajja, facia etc and applying two coats of water based acrylic weather proof exterior emulsion (Apex ultima superior quality) paint over a coat of primer as per manufacturer's instruction including providing 1 to 2 mm thick wall care putty complete all as specified and directed.

M & L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed.

M & L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, not exc 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

M & L for cutting holes exc 150 sqcm but not exc 400 sqcm (superficial area) into or through brick/concrete block walls built in cement mortar complete all as directed.

Supplying and laying of 20mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 25mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 50mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S & F 20mm CPVC ball valve brass insert complete all as directed.

S & F 25mm CPVC ball valve brass insert complete all as directed.

S&F rotational moulded polyethylene water storage tanks 2000 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 20 mm dia brass ball/float valve high pressure with polythene float and flynut, 25 mm water tank nipple, union suitable for HDPE water tank, 25mm bore gun metal gate/globe valve with iron wheel head including taking down old unserviceable PVC tank of same capacity complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks 500 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 20 mm dia brass ball/float valve high pressure with polyethene float and flynut, 25 mm bore HDPE water tank nipple, union suitable for water tank complete all as specified and directed.

S & F in repairs, vitreous China wash down water closet pan (pedestal pattern),P or S trap type, white, including connection to outgoing drain and 32mm dia flush pipe,flushing pipe, anti syphonic pipe with white PVC seat and cover and 10 ltr capacity low level PVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long complete including making good damaged/disturbed surfaces complete all as specified and directed. Make PRAYAG Cat No 4125 or equivalent of CERA/Hindware/Parryware

S&F in repair Vitreous China Squatting Pan"Orissa pattern" size 580 mmx440 mm white with integral foot rest S or P trap etc. including 10 ltr capacity low level PVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long and 32mm dia flush pipe, S or P Trap & Provision of concrete bedding and making good to floor all as specified & directed by Engineer-in-charge. Make of Pan CERA Cat No S3010108 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag

S&F in repair Vitreous China Wash hand basin , white flat back size 550x400 mm including a pair of mild steel angle iron brackets duly painted, erected/embeded in wall, providing Pillar Tap 15 mm bore Chromium plated cast copper alloy with capstan heads, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts & 32 mm dia LDPE PVC waste pipe, PVC connection 15 mm size 600 mm long including cutting hole and pinning in ends making good disturbed portion using cement mortar 1:3 complete all as specified & directed by Engineer-in-charge. Make of WHB CERA Cat No S2010105 or equivelent of PRAYAG/HINDWARE/PARRYWARE

S & F Vitreous China urinal, half stall type, white (minimum) with grating and union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete complete as specified and directed. (Make: Parryware Cat No. C0575 or equivelant of make Hindware/Cera)

S & F Vitreous China (white) urinal partition of approximate size 90X320X720 mm. Make CERA Cat No S4090101 or equivelant of make Parryware/Prayag/Hindware as approved by GE.

S&F swivel shower with shower arm 225 mm long of PTMT, any colour, suitable for 15 mm pipe fixed with and including chromium plated brass screws in wooden/plastic cleat or rawl plug complete all as directed.(Minimum weight 40 gms).Make Prayag Cat No. 181 for shower & 184 for arm or equivalent of other make as approved by GE.

S&F for 50 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

M & L 15 mm bore urinal spreader chromium plated complete all as directed. Make CERA Cat No F8070201 or equivalent of Hindware/Parryware/HR Jonson

S&F in repair 15 mm bore concussive push button taps cast copper alloy chromium plated screwed down to iron pipe, complete all as specified and directed

S&F 15 mm bore push tap of any colour high pressure, PTMT, screwed for iron pipe complete all as specified and directed (Min weigh 47 gms)

S & F PVC connection pipe with PTMT nuts, 600 mm long. Make: CERA/Hindware/Parryware/PRAYAG

S&F Shelf 18 inch long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 300 gms) complete all as specified and directed. Make Prayag Cat No 191 or equivelent as approved by GE

S&F in repair 15 mm bore bib taps with flange cast copper alloy chromium plated with capstan head screwed down to iron pipe complete all as specified and directed. Make: CERA Cat NO HT-F3001151 or equvelent of Make Hindware/Parryware/PRAYAG

S&F in repair 15 mm bore stop cock valve cast copper alloy chromium plated fancy type with long shank and cup, concealed type, screwed down to iron pipe complete all as specified and directed. Make: CERA Cat NO HT-F3001201 or equvelent of Make Hindware/Parryware/PRAYAG

S&F 15 mm bore stop valves/angle valve cast copper alloy chromium plated fancy type with long shank and cup, concealed type, screwed down to iron pipe complete all as specified and directed. Make: CERA Cat NO F1017351 or equvelent of Make Hindware/Parryware/PRAYAG

S&F 25 mm dia stainless steel metalic coated curtain rod with ring brackets etc complete all as specified and directed

S&F stainless steel curtain rod bracket suitable for 25mm dia curtain rod including wooden support etc complete all as specified and directed

S & F PTMT towel ring with chromium plated screws (Minimum weigh 90 gm) complete all as specified and directed. (Make: PRAYAG or equivalent)

S & F brass chromium plated tubular towel ring, fancy type complete all as specified and directed. (Make: PRAYAG Cat NO BA-21 or equivalent of Parryware /Hindware/Cera)

S&F in repair towel rail 600 mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats.(Minimum weight 190 gms) complete all as specified and directed.

S&F in repair 110 mm dia PVC (SWR) pipes, Type 'B', single socketed,in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed.

S&F in repair 75 mm dia PVC (SWR) pipes, Type 'B', single socketed,in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed.

S & F 110 mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with solvent cement joints fixed to wall using MS holder bat, etc complete all as specified and directed.

S & F 75 mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with solvent cement joints fixed to wall, using MS holder bat etc complete all as specified and directed.

S & F 110 mm bore, PVC (SWR) bends of any radius with acess door complete all as specified and directed.

S & F 75 mm bore, PVC (SWR) bends of any radius with acess door complete all as specified and directed.

S&F PVC (SWR) junction single,(single T) 110 mm with access door complete all as specified and directed.

S&F PVC (SWR) junction single,(single T) 75 mm with access door complete all as specified and directed.

S&F PVC (SWR) vent cowl suitable for 110 mm dia pipe.

S&F PVC (SWR) vent cowl suitable for 75 mm dia pipe.

S & F 75 mm dia outlet , PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F in repair 75 mm dia outlet , PVC (SWR) multi floor trap, with grating including jointing to waste pipe with solvent cement, fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F in repair 125/110mm, PVC (SWR) gully trap, with grating including jointing to waste pipe with solvent cement, fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

M&L for contraction joints (Dummy) 65mm deep x 10 mm wide filled with sealing compound Grade ‘A’ complete all as specified and as directed

E/M PORTION : - (EARTH WORKS AND CONCRETE WORKS IF ANY RELATED TO E/M WORKS SHALL BE MEASURED AND PAID UNDER RESOECTIVE ITEM CATERED IN B/R PORTION) : Taking down copper/ aluminium point wiring(light, fan, socket or power) complete, including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperately) and making good distrubed surfaces of wall, floors, etc complete.

Point wiring with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalic conduit (Medium grade) on surface conforming to IS-9537 with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thick laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor (FRLS) earth continuity conductor to common earth and connecting to earth dolly all as specified for :- One light or fan point controlled by one 5 Amps switch one way

All as per item No 130 above but for one 3 pin socket point 5 Amp on independent board

All as per item No 130 but for one 3 pin socket point 5 Amp on same board with other switches.

All as per item No. 130 above but using single core multistranded copper conductor 2.5 sqmm ( Nominal area ) cable with 2.5 Sqmm size copper earth continuity conductor (both FRLS) for 3 pin 15 A socket outlet on independent board complete all as specified and directed.

Supply and fix Switch piano, flush button single pole, 5 Amps one way. Make : Anchor/Cabtree/Legrand/Standard

Supply and fix Switch sokcet combination flush type 5 Amp 2/3 pin muliti purpose Make : Anchor/Cabtree/Legrand/Standard

Supply and fix Switch socket combination flush type 5/15 Amps 3/3 pin universal multipurpose Make : Anchor/Cabtree/Legrand/Standard

Supply and fix Ceiling rose surface bakelite 65x50mm three terminals including supply and fix PVC blocks. Make : Anchor/Cabtree/Legrand/Standard

Supply and fix Fan regulator electronic, step & socket type (Five step), 230 volt, suitable for 1200/1400mm sweep ceiling fan. Make : Anchor/Cabtree/Legrand/Standard

Supply and fix in replacement Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN 8 way horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

Supply and fix in replacement Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN 4 way horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

Supply and fix MCB single pole & neutral 6 to 32 Amps 240 volts, C series,10 kA rupturing capacity

Supply and fix MCB single pole 6 to 32 Amps 240 volts, C series, 10 kA rupturing capacity

S&F in replacement Pride plus inverter batten of make Havells, LED tube light fitting of 20 watts 6500K , 230 volt, with polycarbonate channel , lithium Ion battery with charging time 8-10 hours and back up time 4 hours complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Havells Cat No LHEXACP7FN1W020 OR equivelant of make Shakti/Crompton Greaves/Bajaj

S&F new generation energy saving environmental friendly long life, with high power LED building street light/security light 1x 35 Watt LED pressure die-cast aluminium, heat resistant, toughened glass diffuser, IP65/66 protection and impact resistant of IK7 prewired with all accessories and connection up with 3 core flexible copper conductor cable 4/20 mm size, 1.5m long and testing on installation all as specified and directed. Make:- Superb street light of Havells Cat No LHEXAYP7PN6K030 or equivelent of Bajaj/phillips/CG

S&F security light bracket made out of 25 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size 50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply & Fixing star rated energy saving ceiling fan 1200mm sweep (white) with all accessories including down rod and hanging the ceiling fan from existing fan hook with 3 core flexible copper wire 24/0.20 sqmm from ceiling rose, etc all as directed. Make : Model ES-50 of Havells or equivalent in Usha/Orient.

Supply and Fixing exhaust fan, 300mm sweep metal body, AC single phase 230/240 Volt including bird free louver shutter cut to fit with hole for exhaust fan including providing holes grouting bolts and 3 core flexible copper conductor cable of size 24/0.20 sqmm connecting up from ceiling rose to exhaust fan terminal complete all as directed. Make : - Usha/almonard/Crompton/Khaitan/ Bajaj. NOTE: - Quoted rate deemed to be inclusive of making hole in brick/stone wall by using core cutting machine for providing exhaust fan in wall including making good to match with existing and necessary fixing arrangement of louvre using nut, bolts, washers etc complete.

M & L for Sand cushioning and covering with clean dry river sand in trenches for protection of under ground cables (below, above and around the cable laid in trenches) complete all as specified and directed. (Note: Thickness after punning down shall be measured for payment)

Supply and laying well burnt bricks, locally available best quality bricks laid breath wise across the length of cable in trenches for protection of UG cables complete all as specified and directed.

S & F 40mm bore GI pipe "light grade" for protection & passing of LT cable fixed to poles/walls/laid under floor/roads complete including fittings/clamps, two coats of aluminium paint over a coat of zinc chromate primer complete all as specified

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, GI strips armoured LT UG cable for working voltage 1100 volts, 2 core, nominal cross sectional area of main conductor 16 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, culverts, under floors, through GI Pipe complete all as specified and as directed.

Supply, laying and testing GI water tubing 25 mm bore "medium grade" including all fittings to laid in trenches including necessary cuttings, threading and testing on completion all as specified and directed by Engr-in-Charge.

Supply, laying/fixing, connection and testing, 40mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixtures complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

S & F 25 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 455 gms) complete all as specified and directed.

S & F 25 mm bore, gun metal gate valve, with iron wheel head, screwed both ends, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make: - Zoloto/Kirlosker/Gem as approved by GE

M&L, Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.0mm thick buried directly in ground (earth pit depth not less than 2.25m deep below the ground level) with top edge of earth plate at a depth not less than 1.5m below ground level connected to earth using GI earth wire of 4 mm dia by means of of nuts, bolts and washer and check nuts of GI or steel as shown in electrical plate No.3 of MES SSR-2009 (Part-I) and connected to earth test point all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 metre long for earth including PCC (1:2:4) pit with RCC (1:2:4) type B-1 cover, 40mm thick reinforced with 6mm dia MS bars @ 100mm both ways with lifting hooks made out of 6mm dia MS bars, watering arrangement with 20mm dia light grade pipe, funnel, wire mesh, common salt chorcoal, necessary excavation and earth work in any type of soil complete all as specified.

SRI MAHALAKSHMI CONSTRUCTIONS