Khudia Rangaphali

Amount

BRIDGE PROPER : Excavation for Structures: Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. i. Ordinary soil: Mannual Means ( With out dewatering): Depth upto 3m

Excavation for Structures: Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. i. Ordinary soil: Mannual Means ( With out dewatering): Depth from 3.0m to 6.0m

Bored cast-in-situ M35 grade R.C.C. pile excluding reinforcement complete as per drawing and technical specification and removal of excavated earth with all lifts and lead upto 1000m.'With plasticiser (Masterplast PL-1/SPL-2 or equivalent), air entraining and water reducing plasticiser ( asterplast PAE or equivalent) and accelerating plasticiser (Masterplast ACPL or equivalent) conforming to IS-9103-1999)(Pile diameter-1000mm)

Pile load test on single vertical pile in accordance with I.S. 2911 (Part IV)as per technical specifications of MORTH section no 1100 a) Initial and routine load test

Levelling course for Pile cap Providing and lying of PCC M - 15 levelling course below the pile cap. as per drawing and technical specifications 0f MORTH section

Cement concrete for reinforcement concrete in pile cap complete as per drawing and technical specifications A. RCC grade M - 25 (i ) Using concrete mixer

Reinforcement in Foundation: Supplying, fitting and placing TMT IS:1786 Fe500 D bar reinforcement in foundation complete as per drawing and technical specifications a. TMT-IS 1786 ( Fe-500 D) Primary Producer (TATA/ SAIL/ Esser Steel/ Jindal panther steel/ Shyam steel or equivalent)

Plain/Reinforced cement concrete in sub-structure complete as per drawing and technical specifications and steel shuttering formwork as per MoRTH specification A. RCC Grade M25: Height from 5m to 10m : Case I Using concrete Mixer

Supplying, fitting and placing a. TMT IS:1786 Fe500 D bar reinforcement in substructure complete as per drawing and technical specifications a. TMT-IS 1786 ( Fe-500 D) Primary Producer (TATA/ SAIL/ Esser Steel/ Jindal panther steel/ Shyam steel or equivalent)

Furnishing and placing Reinforced/Prestressed cement concrete in super-structure as per drawing and technical specifications including steel shuttering formwork. i. without plasticiser (A)RCC Grade M 25 CASE-(I), Using Concrete mixer (i) For Solid slab, (a) Height from 5m to 10m

Supplying, fitting and placing a. TMT IS:1786 Fe500 D bar reinforcement in superstructure complete as per drawing and technical specifications a. TMT-IS 1786 ( Fe-500 D) Primary Producer (TATA/ SAIL/ Esser Steel/ Jindal panther steel/ Shyam steel or equivalent)

Providing and laying Cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications

Construction of precast RCC railing of M30 Grade in situwith 20mm nominal size aggregate true to line and grade, tolurence of vertical RCC post not to exceed 1 in 500, centre to centre spacing between vertical post not to exceed 2000 mm, leaving adequate space between vertical post for expansion, complete as per approved drawings and technical specifications

Drainage Spouts complete as per drawing and Technical specification.

Burried Joint (Providing and laying a burried expansion joint, expansion gap being 20 mm, covered with 12 mm thick, 200 mm wide galvanised wieldable structural steel plate as per IS: 2062, placed symmetrical to centre line of the joint, resting freely over the top surfaces of the deck concrete, welding of 8mm dia, 100mm long galvanized nails spaced 300mm C/C along the center line of the plate , all as specified in clause 2604.)

Providing & fixing 20 mm thick compressible fibre board in expansion joint complete as per drawing & Technical Specification.

Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical specification.

Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification i. Sandy material

Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2. of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size toeards the wall and provided over the entire surfaces behind the abutement, wing wall and return wall to the full height compacted to firm condition complete as per drawing and technical specification.

Reinforced cement concrete approach slab including reinforcement and formwork complete as per drawing and Technical specificationa. TMT-IS 1786 ( Fe-500 D) Primary Producer (TATA/ SAIL/ Esser Steel/ Jindal panther steel/ Shyam steel or equivalent)

PCC M15 Grade leveling course below approach slab complete as per drawing and Technical specification

Carrying out Sub Soil Investigation ( SSI), for all types of soil (except boring in rock) upto a depth of 30m or refusal ( N=100) for each foundation location as per IRC : 78-2014 and submission of SSI report to the Engineer in -Charge for approval. Preparation & submission of Design calculation & Drawings of foundations, Sub Structures, Super Structures as per relevant IRC codes and SSI report , 2 ( two) copies each of Design & Drawings of each Bridge to be submitted for approval and 8 (eight) copies after approval of competent authority.

Protection work : ' Boulder apron laid in wire crates (Providing and laying of boulder apron laid in wire crates made with 4mm dia GI wire conforming to IS: 280 & IS:4826 in 100mm x 100mm mesh (weaved diagonally) including 10% extra for laps and joints laid with stone boulders weighting not less than 40Kg each.)

Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specifications as per drawing and Technical specification. i. Stone/Boulder

Providing and laying Filter material underneath pitching in slopes complete as per drawing and Technical specification as per drawing and Technical specification .

ROADS WOTRK : Embankment Construction with Material Obtained from Borrow Pits(Construction of Embankment with approved materials obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300.1 and 300.2 ( including compensation of earth)(Including cost of testing of materials at site and laboratory as directed by the deptt. as per technical specification (A) From private land

Construction of Sub grade and Earthen Shoulders (Construction of Sub grade and Earthen Shoulders with approved materials obtained from borrow pits, with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 ( including compensation of earth)(Including cost of testing of materials at site and laboratory as directed by the deptt. as per technical specification i. From private land

Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2):( Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 ( including all lead , transporting to site) Material as per technical specification 401: (I) for grading- II Material

Water Bound Macadam: (Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density. ( including all lead , transporting to site ) as per technical specification 405.(A) By Manual Means: (II) Grading- II. (a) Using stone Screening type –A (13.2 mm Agg.)

Providing and laying interlocking concrete block pavement ( M-40 Grade) having thickness 80mm as per technical specification clause 1504 complete including carriage (i) Including Edge block/Eddge restraints

Retro reflectorised Traffic sign: Providing and erecting of Retro-Reflectrorised cautionary, mandatory & informatory sign as per IRC: 67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly design foundation with M-15 grade Cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing and sign. ( All the Steel work must be Tata/Sail/or any other approved brand) i. 60cm equilateral traingle

Raju Mesh