CERTAIN SPECIAL REPAIR TO BLOCK NO P 20 QTR NO 1 TO 8 AT NEEL BHAWAN OR MD ACCN AND OTHER SANCTIONED WORK UNDER GE WEST FEROZEPUR CANTT

Amount

Dismantling of Brick tiles or terracing tiles, single layer on roof

Demolition of Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof)

Mud phuska, 80mm thick average, consolidated thickness, on flat roofs including 25 mm thick mud plaster complete all as specified.

Rendering/plastering, 10mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, , surfaces finished even and smooth without using extra cement complete all as specified.

A tack coat of industrial bitumen 85/25 @ 1.20 Kg per square metre over a coat of bitumen primer @ 0.30 litre per square metre including preparation of roof surfaces complete all as specified.

150 mic popy film including preparation of roof surfaces complete all as specified.

M&L for Brick tiles 40mm thick laid on mud mortar and joints grouted flush in cement mortar (1:3) mixed with 5% of cruide oil by weight of cement and on mud phuska complete all as specified.

All as per Ser Item No 7 above but except tiles.

Flush pointing to roof tiles in cement mortar (1:3) tiles including racking out joints complete all as specified.

Taking down cement plaster from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc complete all as specified.

Excavation in trenches, n exc 1.50 m wide and 1.50 m in depth and getting out in hard/dense soil including clearing away all grass vegetation, saplings, shrubs, roots and trees not exceeding 30 cm girth and removing rubbish all as directed by engineer-in-charge

Returning, filling in, including spreading, leveling, watering and well ramming soft/loose soil in layers n. exc 25 cm thickness

Removing excavated soil n exc 50 m and depositing where directed at a level n exc 1.50 m above the starting point

Demolition and breaking up salt glazed stoneware (SGSW) drain pipes set in cement mortar internal dia of pipe 150 mm.

M & L cement concrete 1:4:8 type D2 as in bed to drain pipes including packing under 6and haunching against the sides of pipes after they are laid & tested for 150 mm bore pipe

M & L 150 mm dia salt glazed stoneware drain pipes laid in trenches and jointed as specified

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for & forming branch channel (1/2 round or ¾ section) in cement concrete 1:2:4 type B1 smooth finished and reforming branching as required for 150 mm dia pipes

Rendering/plastering, 15mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces,, surfaces finished even and smooth without using extra cement complete all as specified.

M/L rendering 15mm thick in CM 1:6 on fair faces of brick work , finished even and smooth without using extra cement complete all as specified.

M/L rendering 10mm thick in CM 1:3 on fair faces of concrete finished finished even and smooth without using extra cement complete all as specified.

M/L rendering 12mm thick in CM 1:6 on fair faces of brick work , finished even and fair without using extra cement.

Supply only integral water proofing compound .

M&L for preparing newly plastered surface and applying two coats of cement base paint on wall surfaces complete all as directed.

M&L for complete removal of existing treatemnt and applying two coats of cement base paint on wall surfaces complete all as directed.

M&L for preparing newly plastered surface and applying two coats of white wash on wall surfaces complete all as directed.

M&L for complete removal of existing treatemnt and applying three coats of white wash on wall surfaces complete all as directed.

M&L for preparation of newly plastered surface of walls and applying two coats of white wash over wall complete all as specified and directed.

M&L for preparation of old plastered surface and applying two coats of white wash over wall complete all as specified and directed.

M&L for preparing newly plastered surfaces of wall and applying three coats of distemper oil emulsion any shade over a coat of 3mm thick wall care putty complete all as directed

M & L for complete removal of existing treatment over wall and applying two coats of distemper oil emulsion over 3mm thick wall care putty complete all as directed.

M&L for preparation of newly plastered surface and applying three coats of white wash over ceiling complete all as specified and directed.

M&L for preparation of old plastered surface of wall and applying one coats of white wash over ceiling complete all as specified and directed.

Taking down chowkhats or frame n exc 1.5 sqm (without taking off shutter from the frames)

Taking down door chowkhat or frame exe 1.5 sqm but n exc 4 sqm shutter (without taking off shutter from the frames)

Taking down shutters of any description exc 1.00 sqm area and not exc 2.00 Sqm each and refixing in the same opening complete all as directed.

Taking down shutters of any description not exc 1.00 Sqm each complete all as specified and directed

Taking down existing chowkats or frames , without taking out shutters ,from the frame , n exc 1.5 SqM

M&L for second class wrought hard wood as in scantling timber framed and fixed

S& F Factory made, Pressed steel frames made of 1.25mm thick MS sheet of profile 125x60mm for door and window frames with one rebate including lock strike plate, shock absorbers, 20mm dia 60mm long MS conduit for housing of a drop bolt, butt hinges, hold fasts/lugs etc and treating of internal surfaces of chowkhats and hold fasts/lugs with a coat of coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

S& F Factory made, Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one rebate including lock strike plate, shock absorbers, 20mm dia 60mm long MS conduit for housing of a drop bolt, butt hinges, hold fasts/lugs etc and treating of internal surfaces of chowkhats and hold fasts/lugs with a coat of coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

Providing cement concrete 1:2:4 type C1 (20mm graded agg) in win- dow or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, ier aps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets, etc. (of any section indicated), with plain fair faces,E28 including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match complete all as specified and directed by EIC

Factory made, 35mm thick, 2nd class hard wood (Hollock), plain framed, panelled shutters, any number of panels, panels shall be of 12mm thick BWR glade veneered particle board medium density, wood particle board with commercial face veneers, size of members as specified in clause 8.20(a) of MES Schedule Part-I in Section-8 complete all as specified.

S& F Factory made, 35mm thick, 2nd class hard wood (Hollock), glazed and skelton shutters, open rebated and prepared to receive glass/ gauge etc(without sash bar) edges of framing plain , chamfered or rounded fitted with cut and mitered beads for securing glass etc size member of shutters as specified in SSR Pt I ,section 8, clause 8.24 (a) of MES Schedule Part-I in Section-8, complete all as specified.

Small articles of 2nd class hard wood (hollock, sheesham wood may be used without financial adjustment), such as hinge blocks, door and window stops, articles not exceeding 200 cubic centimeter each and fixed with steel screws, complete all as specified.

S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate inclunding fixing to existing steel or wooden frame complete all as specified and directed

S&F Butt hinges,medium weight, cold rolled mild steel,100mm long and fixed

S&F Mild steel pressed handles 150 mm, oval type, stove enamelled black

Mild steel sliding door bolts plate type, stove enamelled black, with bright bolt not less than12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on length of bolt 300mm long staple plate and fixed

Aluminium anodised,barrel tower bolts 200 mm long of extruded section and fixed

All as per ser Item No 49 but 150mm in size

Wire cloth galvanised mild steel, 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified.

All as per ser Item No 51 but in repairs

Painting to new wood surfaces of any description, over 10cm width or girth two coats with synthetic enamel paint over a coat of pink primer including preparation of surfaces complete all as specified.

Dismantling structural steel work including door, gates, shutters but excluding framed truss etc

Framed mild steel work of grade E-165 (Fe-290) as in framed work such as doors, gates or frame for cooler stand with gusset plates, rails, braces etc, drilled for fixing of sheeting or other covering of door etc, to be prepared for hanging or sliding etc including either hooks and hinges or steel hanging door fittings and hanging and fixing complete all as specified.

M&L for Plain fillets, square or rectangular or triangular in section, clean sawn, secured with nails or beads area exc 13 & nexc 25 Sq cm complete all as directed

Providing and fixing factory made PVC cup boards/ Shelf / Partition of required size consisting of panel of 18mm thick Celuka PVC Ply and for supporting the hold of Shelf/ Partition and shall provided 3edges in size 18mm x18mm as per required length. The front side of the edge visible in the front of the shelf/ Partition to be edge lipped by 18mm width x 1mm thick PVC sheet using solvent cement etc. complete as direction of Engineer-in-charge, manufacturer's specificaton and drawing.

S&F Extruded aluminium alloy handles, fabricated type,anodised 125mm long

S & F continuous (Piano) hinges M S bright finish or Electro galvanized 25 mm wide flaps (when open) including welding to existing frame complete all as specified and directed.

S & F in repairs 25 mm dia, cupboard Knobs fixed with nut, screws and washer of mild steel, bright finished

S & F magnet catchment of specified shape and size for cupboard selves in kitchen

M&L Size of hasp and staple in 125mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws but of aluminium anodised

Grating round 140 mm size of PTMT.(Minimum weight 50gms)

S& F aluminium alloy ,anodized sliding door bolt with hasp and staple and fixing clips of sheet , cast or extruded section , and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed length of bolt 300 mm , fixed iin repairs

S&F Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type B-21 complete all as specified and directed

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified.

M&L for dismantling Stone slabs or interlocking tiles of any description or thickness in floors, aprons etc.Laid dry complete all as specified and directed

M&L broken stone or boulder hardcore of gauge n exc. 63mm, deposited, spread and leveled in layers n exc. 15cm thick, watered and rammed to a true surface.

Cement concrete (1:4:8) type D2 40mm graded agg in foundations, filling and mass concrete complete all as specified and directed

M & L Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade over sand cushioning complete all as specified and directed.

All as per ser item No 70 but except tiles

M & L sand filling under floors or in foundations or cable protection including watering and consolidation complete all as directed by Engieer-in-charge .

Cement concrete (1:3:6) type C-2 using 20 mm graded stone aggregate as in plinth protection, 50mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints complete all as directed by Engr-in-Charge and as specified.

Demolition of brick work built in cement mortar of any specification and in any position complete all as specified.

Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified.

Demolition of reinforced cement concrete as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas, shelves, over head tank and similar suspended work and removing debris outside MD land complete all as directed by E-in-charge.

Demolition of unreinforced cement concrete (reinforce-ment cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for and removing debris outside MD land complete all as directed by Engr-in-charge.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc.Laid, bedded and pointed in any mortar

M/L RCC 1:1.5:3 type A1 using 20mm graded aggregate as in Precast cover slab , shelves and similar articles and setting in mortarcomplete with joints to match complete all as directed.

M/L TMT bars 10mm dia and over cut to length bent to shape required including cranking and bending etc and binding with MS wire (annelaed) not less than 0.9mm dia or securing with clips..

M/L TMT bars 5 mm dia and over and upto 10 mm dia ,as in stirrups cut to length bent to shape etc including cranking and bending and binding with MS wire not less than 0.9mm dia.

M/L RCC 1:2:4 type B1 using 20mm graded aggregate as in Precast cover slab , shelves and similar articles and setting in mortarcomplete with joints to match complete all as directed.

S&F Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

All as per item no 83 but 6mm to 8mm dia, but as in stripps

M&L for factory made box type window with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as directed as per Drg No CEJZ/TD-1019/08 & CEJZ/TD-1020/08

M&L for factory made box type window with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter steel handle and with without glazing bars both dovetailed or welded and with one shop coat of zinc chromate primer complete all as directed as per Drg No CEJZ/TD-1019/08 & CEJZ/TD-1020/08

M&L for factory made box type steel ventilator side/top hung with glazing bars dovetailed or welded and with one shop coat of zink chromate primer complete all as directed as per Drg No CEJZ/TD-1019/08 & CEJZ/TD-1020/08

3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads, in squares n.exc 0.50 Sqm in each pane complete all as specified.

S&F 3mm thick, frosted sheet glass ordinary quality and glazing, with oil putty or with wooden beads, in squares n.exc 0.50 Sqm in each pane complete all as specified.

S&F framed work such as grills, gratings etc.. With ends of bars shouldered and or riveted or forged into spikes , framed guard bars ,barred iron doors , ladders , framed balusters , walk ways , railings, frame work of water tanks and similar work conforming Fe 290 , Gde -E -165

M&L for preparation of old wooden surface of any description over 10 cm width or girth and applying one coat of synthetic enamel paint white or tinted complete all as directed.

Painting to new steel surfaces of any description, over 10cm width or girth two coats with synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified.

M&L for preparation of old painted steel surface of any description , over 10 cm width or girth not otherwise described and applying one coat of synthitic enamel paint white or tinted all as directed.

S&F in repair Low level flushing cistern, PVC (white), 10 liters capacity, with inlet ball float valve, PVC flush pipe and necessary fixing accessories including connecting to existing water pipe and WC etc complete all as specified.

M&L for chromium plated Shower rose,with or without swivel joints any size including fixing to steel pipe or union 15 mm dia.

M&LWash hand basin, flat back 550x400mm vitreous china (white) including PTMT waste fittings of 32mm bore size, waste pipe PVC of 32mm bore,PVC connector 450mm longs with angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing as in repair complete all as specified.

M&L for Tubular towel rail, of aluminium anodized 20mm dia, D type, 60cm long between flanges fixed to wall complete all as specified and directed.

S & F in repairs sink with drainage board made of stainless steel 1mm thick kitchen with plug washers and waste coupling and pipe incl cantilever brackets and connecting union to pipe overall size 915x460mm, bowl size 410x330x160 mm complete all as specified

Fixing only in repairs kitchen sink with plug washers incl replacing cantilever brackets and PVC waste pipe and connecting union to pipe of any size complete all as specified and directed.

M&L 32 mm bore high density polyethylene (HDPE) pipes of pressure rating 6 Kgf/sq.m laid in floor or walls

M&LWash hand basin, flat back 550x400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing as in repair complete all as specified.

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified.

S& F Factory made, solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement and fixed in the frame at site complete all as specified in clause 8 B.2.1 of MES schedule Part-II (2004).

PTMT tower bolts, 150 mm long and fixed with steel screws complete all as specified.

PTMT butt hinge, 100mm long, fixed with steel screws with brass/bronze hinge pin complete all as specified.

PTMT handle 125 mm long fixed with steel screws complete all as specified.

Pillar taps, 15mm dia cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F in repair Chromium plated Soap dish complete all as specified and directed

Waste coupling of PTMT for 32 mm bore dia of discharge pipe (half or full threaded (Minimum weight 32mm-45gms/40mm-60 gms

Taking down vitreous china wash hand basin, of any size and pattern and fixing the same in any position complete all as directed in repairs

M&L Squatting pan orrissa pattern vitreous china white of size 580mm x 440 mm with integral foot rests including necessary lime concrete and 100 mm bore sand cast cast iron ‘P’ trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints, fixed in repairs, complete all as specified.

All as per ser Item No 111 but fixing only

Supply only liquid water proofing compound as per manufacture instruction.

Dismantling floor, hearth or wall tiling including cement mortar beding (but not backing),removing serviceable tiles to store and rubbish off the premises

M/L Non skid ceramic coloured tiles 7-8 mm th (square or rectangular)area of eacch tile exc 0.11 SM but not exc 0.18 SM in floors etc.. Set and jointed in neat cement slurry and pointed in white or coloured cement. to match as in floors including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surfaces 300 X 200X 7 mm th set and jonnted in cement slurry and pointed in white or colour X 7 mm th set and jointed in cement slurry and pointed in white or colour cement to match including 10mm thick back coat in cM 1:4 complete all as specified and directed.

M/L Non skid ceramic coloured tiles 7-8 mm th (square or rectangular)area of eacch tile exc 0.06 SM but not exc 0.11 SM in floors etc.. Set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floors including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid 15 mm thick in cm 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to mirror finish complete all as specified and directed.

M&L for machine cut kota stone in risers of steps,skirting and dado 20-25 mm thick over cement plaster 10 mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to mirror finish complete all as specified and directed.

M & L Green marble slab, 16-18mm thick of size not less than 1 Sqm each, machine cut as cooking platform or in any position, set and bedded in gray cement slurry over & including 15mm thick screed in cement mortar (1:4) and pointed in white cement with admixture of pigment to match the shade of marble including cutting, polishing (mirror type) complete all as specified.

Machine cut cudappa stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab with rubbing and polishing complete including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

S & Fmild steel curtain rod powder coated with fixing side brackets, end cups, rings @ 10 Nos RM and fixed with PVC rawl plugs & Steel screws as in repair complete all as specified.

S&F 0.56mm thick stainless steel plate rack of standard pattern of size 900 x 750 x 250mm. The thickness of stainless steel sheet shall be 1.0 mm and grade of sheet shall be 304 AISI including fixing to wall with 4 Nos 50 mm screws and PVC rawl plugs complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required

S&F cast iron soil, waste and vent pipes of 75 mm bore in any length with or without ears with cement joints fixed to wall complete all as specified and directed.

S&F CI bends of 75 mm bore diminishing pieces or tapers including jointing with CM 1:3 and making good complete all as specified and directed

S&F cast iron soil, waste and vent pipes of 100 mm bore in any length with or without ears with cement joints fixed to wall complete all as specified and directed.

S&F CI bends of 100 mm bore diminishing pieces or tapers including jointing with CM 1:3 and making good complete all as specified and directed

Taking up or down 20mm steel tubing and connections including cleeaning for refixing or removal to store complete all as directed.

Taking up or down 15mm steel tubing and connections including cleeaning for refixing or removal to store complete all as directed.

S & F steel water tubes, 20mm diameter medium grade galvanized, with all fitting and fixed to walls and ceiling or laid in floors including necessary cutting through walls and making good with cement mortar .

All as per item no 132 but fixing only 20 mm dia tube any grade to wall and ceiling or laying in floors

S & F steel water tubes, 15mm diameter medium grade galvanized, with all fitting and fixed to walls and ceiling or laid in floors including necessary cutting through walls and making good with cement mortar .

All as per item no 134, but Fixing only 15mm dia tube any grade to wall and ceiling or laying in floors

S & F steel water tubes, 40mm diameter medium grade galvanized, with all fitting and fixed to RCC walls complete and ceiling or laid in floors or in sunken portion as spout including making necessary hole for inseting spout complete all as directed

M&L Bib taps, fancy type cast copper alloy with crutch or butterfly,handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

Stop valve of cast copper alloy, 15mm bore, screwed down, high pressure with crutch or butter fly handle complete all as specified.

M&L in repair for 100mm dia Cast iron Nahani trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socked in any length with rubber ring joints fixed to wall and floor including taking out old broken / unserviceable pipe of any description including fittings complete.

S&F PVC (SWR) 110 mm bore bends of any radius

M&L for taking down serviceable 110 mm bore PVC (SWR) pipes single socked in any length with rubber ring joints and refixed to wall and floor including including fittings complete.

M & L PVC (SWR) floor trap, plain with grating including jointing with solvent cement diameter of outlet 75mm.

S&F PVC (SWR) branch piece, single (single Y) equal or unequal of 110 mm bore including jointing with CM 1:3 and making good complete all as specified and directed.

M& L for Water storage tanks 500 litres capacity, rotational moulded, triple layer polythene (cylindrical vertical with closed top) hoisting and fixed in position on roofs including dismantling existing water storage tank, complete all as specified.

S&F in repair 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S & F in repairs 20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass ferrule

Low density poly ethylene pipes (LDPE) 32mm diaof pressure rating 6 kg/cm2 laid in trenches

M & L for applying bond coat of epoxy bonding agent & cement in 1:1 ratio for bonding old and new concrete on damaged surfaces applying polymer modified mortar in CM 1:3 including mixing of polymer latex additives upto 60mm thickness (Chajjas fins, border etc) (i) Qty of ploymer to be used 15% by weight of the cement. (iii) To achieve required thickness repeat this step after 24 hrs as required.(iv) Keep the surfaces moist using water forg for 5 to 7 days etc complete all as specified and as directed. (v) Rate shall be inclusive of all necessary scaffolding complete all as specified and directed by Engineer-in-CHarge. Make : - Epoxy bonding agent shall be Krishna, Dr Fixit, MC Bauchemie and M/s Cemistik, Sika or Equivalent as directed by Engineer-in-Charge

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground

Excavation in post holes in Hard and dense soil (or similar holes) each not exc 0.5 CuM , getting out , returning in filling in ,and removal of surplus soil to a distance not exc 50 M and depositing where directed

M & L Type C2 1:3:6 (40 mm graded aggre-gate) as in foundation filling & mass concrete

M&L for PCC 1:2:4 type B1 using 20mm graded aggregate as in lintels Cills,Steps, Plinth courses, Railings, Copings, Bed plates , kerbs etc.inlcuding weathering slightly rounded or champfered angles and throating etc..

Supply and fix MS posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165

Supply only chain link MS galvanised fencing any size or type or as approved by Engineer in Charge

Fixing only Chain link fencing incliding line wire any mesh and type to any type of standards, rails, straining bolts etc includign provision of binding wire

S&F Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

S&F mild steel bolts, diameter of neck 12 mm machine made screw bolts not exc 15cm long

M&L for preparation of new steel surafces of any description not otherwise described , over 10 cm width or girth , priming with a coat of red oxide primer and applyinng 2 coats of synthetic enamel paint of approved shade all as specified and directeed by EIC

M&L for preparation of new steel surafces of any description not otherwise described , not exc 10 cm width or girth , priming with a coat of red oxide primer and applyinng 2 coats of synthetic enamel paint of approved shade all as specified and directeed by EIC

M & L for taking down shutter of any description, area n exc 1 Sqm each for repairing the steel windows in any position by replacing the projecting type hinges (Single pane) welding the new hinge and refixing the shutter including applying two coats of synthetic enamel paint over a coat of primer and making the surfaces good all as directed .

M & L for repairing broken edges of chajja's, roof projection, Fascias etc . In small widths/depths ( exposed area not exc 0.50 Sqm ) by breaking the cracked/loose portion and filling with Cement Mortar / Plain Cement Concrete 1:2:4 ,Type B-0 , using 12.5 mm Crushed stone aggregates , including giving a coat of anti corrosive paint to exposed Reinforcement using anti corrosive paint and using chemical for bonding old and new concrete/plaster and finishing with CM 1:3 plastering, incl 2 coats of white wash or colour wash or existing finishes to match the exisitng surfaces incl removing debris , necessary scaffolding, formwork etc all as specified and directed.

Taking down carefully copper /aluminium point wiring (light, fan , socket or power ) complete, fittings such as switches, ceiling roses, pendants, regulators sockets light fitting etc removing materials to store for keetping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls , floors ,etc.

M &L Point wiring complete with 1100 volts grade PVC insulated unsheathed FRLS cable of copper conductor, multi stranded of size 1.5 sqmm, single core, in and including existing rigid non-metallic PVC conealed conduit, with all accessories if require such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks(for housing lamp holders and light fittings etc) and existing MS pressed steel / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire of size 1.5 sqmm unsheated stranded copper conductor with green PVC insulation connected to common earth dolly complete all as specified and directed for the followings :- (a) One light/fan/Bell Point controlled by one single pole one way switch.

(b) One socket outlet on the same board controlled by one single pole one way switch

(c) One 5 amps socket outlet independent controlled by one single pole 5 Amp switch.

All as per Item No 164 mentioned here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 Sq mm PVC insulated copper conductor and 2.5 Sqmm copper conductor for continuous earthing complete.

Supply & Fixing Switch piano flush type single pole one way 5/6 Amp complete all as directed.

Supply & Fixing Switch piano flush type 15 amps, single pole one way duly ISI marked.

Supply & Fixing Socket outlet 5 pin , 5/6 Amps flush type ISI marked.

Supply & Fixing Socket outlet, 2 in one 6 pin 5 and 15 Amps piano flush type ISI marked.

Supply & Fixing bell push flush type 5 Amps duly ISI marked.

Supply & Fixing ceiling rose,PVC/Polycarbonate,isolated three terminals.

Supply & Fixing Lamp holder PVC/Polycarbonate,isolated with back plate suitable for batten fittings including 10W LED lamp complete all as specified and directed.

Supply & Fixing bell ding dong type AC 230 Volt single pole.

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series TPN DBs (Vertical type)fitted with ABS frame and 415 volts 200 Amps rated enameled bus bar 4 way dust and vermin proof ssuitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 volts 200 Amps rated bus bar,Neutral link,Earth bar and Din rail, 8 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified.

Supply & Fixing MCCB 63 Amps, 415 volts, 16 KA, 4 Pole complete all as specified.

Supply & Fixing MCB, Single pole 240 V,6 - 32 Amps 10 KA 'B Series.

Supply & Fixing MCB, Single Pole and neutral 240 V, 32 Amps 10 KA 'B' series.

Supply & Fixing step type regulator Piano switch type ( 5 step) for ceiling fan 1200/1400 mm size 230 volts, 6 Amps.

Supply & Fixing LED tube light fitting 18 Watts,4 feet long decorative ultra slim linear LED lighting fixture with extruded polycarbonate,environmental friendly, energy efficient 230V, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. Cat Part No LCTL-18-CDL of Make : Crompton or equivalent to Havells/Bajaj/Phillips.

M & L for sub main wiring with two single core PVC insulated FRLS cable with Copper conductor unsheathed cable of size 2 x 6 sqmm drawn through in and including PVC Concealed with 1 x 6 sqmm PVC insulated copper conductor single core for continuous earthing complete including PVC conduit 25 mm dia ( Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 6.0 Sqmm and one run of 6.0 Sqmm PVC insulated copper conductor single core,one run of PVC conduit shall be measured as single run)

Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC ( 1:3:6 ) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate, excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009)

Supply & Fixing LED Bldg security light 35 watts, pressure die cast aluminium housing,heat resistane toughened glass with frame,IP 66 protection with bracket (for housing street light fittings) made of GI pipe 40 mm dia light grade 0.90 mtrs long duly cutted and welded at an angle of 120 degree and fixed to wall with 50 mm X 6 mm MS clamps - 02 Nos with 16 mm dia bolts,nuts,and washers complete all as specified and directed.

Supply and lay cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 Sqmm 4 core.

M & L sub class B bricks locally available of size 22x11x7.5 cm laid dry width wise acrose the line of cable in trenches for protection of UG cable

M&L Mild steel galvanised iron pipe light grade (ISI marked) 40mm bore for passing of cable laid in trenches fixed to walls laid under floors, roads including all fittings i.e MS clamps nuts & bolts etc as required all as specified.

M/s Vishant Construction Co

Marwaha Builders

M/s Bansi Lal

M/S Sandhu Const.Co.

Sethi and Company

M/S Pee Kay Builders

S S BUILDERS