ABCDE Govt. Staff Qtrs.

Amount

9.21.2 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part 1) non - decorative type, core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters - 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

9.1.2Q Providing wood work in frames of doors , windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) - Vegesa / Bandaru wood.

9.141 Providing and fixing PVC door frame of size 50 x47 mm with a wall thickness of 5mm (+-0.2 mm ) , made out of single piece extruded PVC profile , with mitred cut joints and joint with 2 nos of PVC bracket of size 190mm x 100mm long arms of cross section size 35 x 15 mm & self driven self taping screws , the vertical door profiles to be reinforced with 40 x 20 mm M.S.rectangular tube of 0.8mm , including providing EPDM rubber gasket weather seal throughout the frame , including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8 x 100 mm long anchor fasteners complete all.

9.142.2 35 mm thick factory made solid panel PVC door shutter , made out of single piece extruded solid PVC profiles , 5 mm (+_0.2 mm ) thick , having styles & rails (except lock rail) of size 95 mm x 35mm x 5mm , out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruted on the hinge side of the profile for better screw holding power , including reinforcing with MS tube of size 40 mm x 20mm x 1 mm , joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement , self driven self tapping.

9.71.1 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc.complete - 125 X 64 x 2.50 mm.

9.96.1 Providing and fixing aluminium sliding door bolts , ISI marked , anodised ( anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade , with nuts and screws etc complete - 300 X 16 mm.

10.25.2 Steel work welded in built up sections / framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in gratings, frames, guard bar, ladder, railings, brackets,gates and similar works.

9.97.3 Providing and fixing aluminium tower bolts, ISI marked , anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade , with necessary screws etc. complete.

15.2.2 Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead - Nominal concrete 1:4:8 or leaner mix (including equivalent design mix).

4.1.11A Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:5:10 (1 cement : 5 coarse sand : 10 graded brick aggregate 40mm nominal size).

2.27 Supplying and filling in plinth with river sand under floors, including watering, ramming consolidating and dressing complete.

4.1.10 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size).

4.1.3 Code No.4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size).

4.3.2 Centring and shuttering including strutting , propping etc. and removal of form work for - retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.

11.40.1 Providing and laying rectified ceramic rustic / matt finish floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS: 15622 of approved make (Somany / Nitco) in all colours , shades, except white, ivory, grey, fume red brown, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including pointing the joints with white cement and matching pigments etc., complete.

17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C.pan) with seat and lid, 10 litre low level white P.V.C. flusing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231,with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required - W.C. pan with ISI marked white solid plastic seat and lid.

18.49.1 Providing and fixing C.P.brass bib cock of approved quality conforming to IS: 8931 -15 mm nominal bore.

18.22.2 Providing and fixing C.P.brass shower rose with 15 or 20 mm inlet - 150 mm diameter.

17.10.2.2 Providing and fixing Stainless steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I.brackets and stainless steel plug 40mm, including painting of fittings and brackets, cutting and making good the walls wherever required - kitchen sink without drain board - 610x460 mm bowl depth 200mm.

31.9.3 Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end) - 25mm nominal bore.

18.48.A Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI: 12701 marked , with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank - Circular Tank.

18.62.5 Providing and fixing PTMT Ball cock of approved quality colour and make complete with Epoxy coatd aliminium rod with L.P /H.P.H.D.plastic ball - 50 mm nominal bore, 242 mm long, weighing not less than 1240 gms.

18.53.1 Providing and fixing C.P.brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931- 15 mm nominal bore.

18.21.2.1 Providing and fixing unplasticised PVC connection pipe with brass unions - 45 cm length - 15mm nominal bore.

17.7.4 Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps ,32 mm C.P.brass waste of standard pattern ,including painting of fittings and brackets ,cutting and making good the walls wherever required - white vitreous china flat back wash basin size 550x400 mm with single 15mm C.P. brass pillar tap.

17.28.2.1 Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete - flexible pipe - 32mm dia.

19.33.2 Providing and fixing on wall/ column face unplasticised - PVC soil and waste pipes (type B) conforming to IS :13592 - 1992 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single socketed pipes 75mm diameter.

19.33.2C Providing and fixing on wall / column face unplasticisd - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Bend 75 mm.

19.33.1 Providing and fixing on wall/ column face unplasticed - PVC soil and waste pipes (type - B) conforming to IS : 13592- 1992 including jointing with seal ring conformation to IS : 5382 leaving 10mm gap for thermal expansion - single socked pipes -110mm diameter.

12.42.6.2 Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - shoe (plain) - 110mm shoe.

19.33.1C Providing and fixing on wall face / column face unplasticised - PVC mould fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend 110 mm.

18.7.3 Providing and fixing Chlorinated Polyvinnyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete - internal work - exposed on wall - 25mm nominal outer dia pipes.

14.46 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc complete.

13.48.1 Finishing with deluxe multi surface paint system for interiors and exteriors using primer as per manufacture's specification - Two or more coats applied on walls @ 1.25 ltr / 10 sqm over and including one coat of special primer applied @ 0.75 ltr / 10 sqm.

13.62.1 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade - Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacure

13.17 6mm cement plaster 1:3 (1 cement :3 fine sand) finished with a floating coat of neat cement and thick coat of lime wash on top of walls when dry for bearing of R.C.C. slabs and beams.

16.96 Supplying fixing and commisioning of Suguna / Texmo / Sharp 2 HP monoblock pumpset slow speed single phase motor. The rate includes the cost of pumpset, pumpset fixing in position and test run etc. complete.

14.6.2D Renewing glass panes, with wooden fillets wherever necessary - Float glass panes of thickness 5.5mm.

1.21.1 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required - 20mm.

Basic Code No.1101 Supplying and fixing 1.5sq.mm ISI maked,FRLS PVC insulated,single core copper conductor cable (multistrand).

Basic Code No.1102 Supplying and fixing 2.5sq.mm ISI maked, FRLS PVC insulated,single core copper conductor cable (multistrand).

Basic Code No.3131.O Supplying and fixing 450mm 1400 rpm heavy duty exhaust fan Make: Almonard/ Orient/ Usha etc complete as directed by the Engineer in charge.

Sl.No. 1198 Supplying and fixing of Crypton FTL 2 x 36 / 40W FTL Street Light (Havells / Crompton) etc complete as directed by the Engineer in charge.

NON-PSR Supply and fixing of 20-24W LED tube light fitting Make: Philips/ Havells/wipro .

sekhar