CA NO CWEAFJ-40/2025-26 SPECIAL REPAIR TO BLDG NO 4/15, 4/16 4/17 AT AIR FORCE STATION JAMMU UNDER GE (AF) JAMMU

Amount

Schedule 'A' Part-I (Building Works)

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level).complete all as specified and directed by Engr -in-Charge. Notes : Demolished material should be thrown out of the defence line at govt approved dumping area.

M & L for cement concrete 1:2:4(Type B-2), 75 mm thick using 40mm graded crushed stone aggregates as in plinth protection finished fair and even,laid to an outward slope of not less than 1:12,plinth protection shall be cast in panels not exceeding 2.00 sqm area with 6mm wide joint between the plinth protection panels,10mm joint between wall and plinth protection and filled with bitumastic filler complete all as specified and directed by Engr-in-charge

M&L for copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directed type B1 (1:2:4) using 20 mm graded aggregate complete all as specified and directed by Engr-in-charge

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches etc complete all as specified and directed by Engr-in-charge Note : Including removal demolished debris out of defence line and dumped at govt approved dumping area and no extra payment will be made to contractor against the same.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc. 6.00m mean radius built in cement mortor 1:6 complete all as specified and directed by Engr-in-charge

Material & labour for brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed by Engr-in-charge

Material and labour for 10 mm rendering in CM 1:6 on fair face of wall or on concrete surfaces finished even and smooth without using extra cement including taking down of existing Plaster complete all as specified as directed by Engineer-in-Charge. Notes : Demolished material should be thrown out of the defence line at govt approved dumping area.

Taking down chowkhats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames) complete all as spd and as directed. Note:- Including make good the Jam of window/Door to receive new door/window by brick work,plaster and matching finishes as required also no extra payment should be made to the contractor against the same complete all as specified and directed by Engr-in-charge

Taking down Chowkats or frames exc 1.5 sq. m but n exc 4 sq m each with shutters (without taking off shutters from the frames) complete all as specified and directed by Engr-in-charge Note:- Including make good the Jam of window/Door to receive new door/window by brick work,plaster and matching finishes as required also no extra payment should be made to the contractor against the same.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) frame work for doors,windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws,includinng taking down existing.all complete as per architectural drawings and the directions of Engineer-in-Charge

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws includinng taking down existing .complete all as per architectural drawings and the directions of Engineer-in-charge.

M&L for anodised aluminium Grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the window frame with C.P. brass/ stainless steel screw @150 mm centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved aluminium standard section around the opening, all complete as per requirment and direction complete all as specified and directed by Engr-in-charge

S&F for pressed steel frames (Factory made) made out if 1.25mm thick mm black MS sheet for doors, with double rebates including necessary lugs, Butt hinges, lock strike plate, etc complete, size of frame 125x60mm incl one shop coat of red oxide zinc chrome primer,incl bottom of each chowkat to be welded with 2 Nos 25x25x3mm thick flat iron projecting 10 cm on either side and back fill to chowkahts with PCC 1:3:6 type C-0 using 12.5mm graded crushed stone aggregate after applying and including one coat of black paint to prevent from corrosion complete all as specified and directed by Engr-in-Charge.

S&F Pressed steel frames (Factory made) made out if 1.25mm thick mm black MS sheet for doors, with one or more rebates including necessary lugs, Butt hinges, lock strike plate, etc complete, size of frame size 105x60mm incl one shop coat of red oxide zinc chrome primer,incl bottom of each chowkat to be welded with 2 Nos 25x25x3mm thick flat iron projecting 10 cm on either side and back fill to chowkahts with PCC 1:3:6 type C-0 using 12.5mm graded crushed stone aggregate after applying and including one coat of black paint to prevent from corrosion complete all as specified and directed by Engr-in-Charge.

S & F 2nd class hard wood 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass , gauze, etc, (without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) fitted to chowkats complete all as specified and directed by Engr-in-charge. Note :- wire mesh shall be measured and paid separately in respective supply only item.

Supply and fixing stainless steel wire cloth 0.63 mm nominal dia of wire and avg wide 1.40 mm aperture of tinned tacks of galvanised wire staple to steel windows/fixed with wooden beads of 2nd class HW to wooden doors/windows complete all as specified and directed by Engr-in-charge

S&F IInd class hardwood panelled door shutters of 35mm thick (any number of panesl) with panels of timber flat on both sides (feathered edged0 or of veneeered particle boad medium density, wood particle board with commercial face veneers, complete all as specified and directed by Engr-in-charge.

S&F for factory made single extruded WPC (Wood Polymer Composite) solid WPC Moulded door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with 4 Nos of 100mm stainless steel butt hinges, 2 Nos 150mm stainless handle ,200 mm SS tower bolt and 150mm stainless steel door stopper of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge

M&L for preparation of new wood or previously untreated surfaces of any description , not otherwise description, over 10 cm width or grith apply two coat of synthetic enemel paint (ordinary tint) over a coat of pink primer complete all as specified and directed by Engr-in-charge

S & F for 150 mm stainless steel barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr-in-charge

S & F for 200 mm stainless steel, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr-in-charge

S & F for 300 mm stainless steel, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed complete all as specified and directed by Engr-in-charge

S&F for mild steel 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed by Engr-in-charge

Supply & Fixing for 150 mm stainless steel handles, cast type, anodised complete all as specified and directed by Engr-in-charge.

Supply & Fixing for 125 mm stainless steel handles, cast type, anodised complete all as specified and directed by Engr-in-charge.

S & F for 75mm size stainless steel butt hinges complete all as specified and directed by Engr-in-charge.

Description all as per Serial No 27 herein before above but 100mm size complete all as specified and directed by Engr-in-charge.

S &F in repair stainless steel 25mm dia fancy type curtain rods fixed to wall with two no's of bracket,two no's of end ball and funnel including taking down of existing curtain rod complete all as specified and directed by Engr-in-charge.

M&L floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 150mm complete all as specified and directed by Engr-in-charge.

Dismantling of boarding any description fixed in any position with nails complete all as specified and directed by Engr-in-charge.

S&F for WPC board 18-20mm thick,one side UV printed designing and back side plain colour printed(weight of board should be 11-12kg per sqm of board) for cup board or kitchen cabinet Front and sides of cabinate boxes and frame full size fitted under cooking platform and other platform including fittings etc complete all as specified and directed by Engr-in-charge.

S&F WPC board 18-20mm thick,both side plain colour printed(weight of board should be 11-12kg per sqm of board) for cup board or kitchen cabinet self ,drawer, fitted under cooking platform and other platform including fittings etc complete all as specified and directed by Engr-in-Charge.

S&F for WPC board 12mm thick,both side plain colour printed(weight of board should be 5-6kg per sqm of board) for cup board or kitchen cabinet back side shutter fitted under cooking platform and other platform including fittings etc complete all as specified and directed by Engr-in-charge

S&F for auto closing hinges 35 mm of 0 crank( KH-001) OR 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete all as specified and directed by Engr-in-charge

S&F for ball bearing runners 45 mm telescopic channel (KTS-20) full extension load capacity 50 kgs complete all as specified and directed by Engr-in-charge

S&F for door/shutter catcher, magnetic stopper/holder with striking plate for WPC board cabinets, cupboard shutters complete all as specified and directed by Engr-in-charge

S&F for brass knobs 35-40mm dia complete all as specified and directed by Engr-in-charge

S&F 100 mm long Extruded brass handles designer type, fabricated type polished complete all as specified and directed by Engr-in-charge

S&F 75 mm long Extruded brass handles designer type, fabricated type polished complete all as specified and directed by Engr-in-charge

S&F for sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engr-in-charge

Dismantling of, stone slabs and tiles of any description or any thickness in floors,aprons including screed bed or flooring etc complete all as specified and directed Notes:-Demolished material should be thrown out of the defence line at govt approved dumping area.

M&L for pre- polished granite slab machine cut of any shade as approved by GE of 18-20 mm thick inc over cement screed bed including edge Moulding,rounding to shape Cutting and nosing with suitable hole for cylender gas pipe, kitchen sink ,WHB, Grinding and Machine polishing to edge to give high gloss finish (Granite finish) with suitable grinding stones and set in 15mm thick CM 1:4 in single piece for platform including taking down of existing tile work including removal of debris out of the defence line at govt approved dumping area and no extra cost will be paid for the same complete all as specified and as directed by Engr-in-charge.

BLANK

M&L for Kota stone slab 20-25mm thick in floor,steps laid over set with neat grey cement slurry mixed with colour over 20mm thick screed in CM 1:4 pigment to match the shade of the slab including Grinding polishing to achieve granite finish including moulding to exposed edges complete all as specified and directed by Engr-in-charge. Note: Kota stone in steps should be provided in single piece & 2mm groove in treads.

M & L for grinding and polishing of existing Kota stone /terrazo cast in situ floor to achive the Mirror finesh complete all as specified and directed by Engr-in-charge

Dismantling of floor hearth or wall tilling including cement mortar bedding (but not backing) and rubbish of the premisses complete all as specified and directed.Note :-Including Removal of debris or excavated material out of the defence line at govt approved dumping area and no extra cost will paid to the contractor against the same.

M&L for non skid/mat finish ceramic colour tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm (Colour and design of tiles as approved by GE), in floors/skirting etc, and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engr-in-charge

M&L for glazed ceramic coloured tiles size 600mm x 300 mm thick (Colour and design of tiles as approved by GE) on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed by Engr-in-charge

Taking down cement plaster on brick or concrete surfaces on wall including racking out joints, hacking for keys, scrubbing down with water etc and rendering 15 mm thick 1:4 mixed with water surfacing compound and finish the surfaces fair & even without using extra cement, complete all as directed by Engr-in-Charge. Note : Removal of debris out of defence land without any extra cost to be deptt.

M&L for preparation of New surface of walls and applying two coat of exterior emulsion/ Apex paint over a coat of primer incl filling gaps with wall care putty and applied using airless spray technology and capable of operating single spray gun with a suitable hose length the spray machine should be reputed manufacturer with pro guard technology and capability of tracking pressure as well as paint and primer usage incl cleaning the floor ,joinary ,surfaces,usage complete all as specified and directed by Engr-in-charge

Taking down cement plaster on brick or concrete surfaces on wall including racking out joints, hacking for keys, scrubbing down with water etc and rendering 10 mm thick 1:6 & finish the surfaces even & smooth without using extra cement, complete all as directed by Engr-in-Charge. Note : Removal of debris out of defence land without any extra cost to be deptt.

M&L preparation of newly plastered surfaces of walls,Applying two coats of distemper with interior emulsion over a coat of primer including necessary formwork scaffolding required upto the 4th storycomplete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and directed by Engr-in-charge

BLANK

Complete removal of existing treatment on wall/roof projections including facia, cornices etc by scrapping with mechanical sander (having mechnical vaccum mechanism ) with sanding pad of appropriate grit to make surface clean, free, from dust, loose paint etc by skilled labour complete all as specified and directed by Engr-in-charge Note :-Including Removal of debris or excavated material out of the defence line at govt approved dumping area and no extra cost will paid to the contractor against the same.

M&L for prepration of new/old surfaces of wall and apply 2mm thick wall care cement based water proof putty (internal and external as per ground requirement) ,necessary formwork scaffolding required upto the 4th story complete all as specified and directed by Engr-in-charge

M&L for preparation of old decorated surface of walls,scrapping down by mechanical means sender with internal dust extraction system for clean enviroment certified by manufacturer smoke ,soot,moulds,mos and efflorosent salt and trading oil and greese spotdown and stopping etc and applying two coat of exterior emulsion/ Apex paint over a coat of primer incl filling gaps with wall care putty and applied using airless spray technology and capable of operating single spray gun with a suitable hose length the spray machine should be reputed manufacturer with pro guard technology and capability of tracking pressure as well as paint and primer usage incl cleaning the floor ,joinary ,surfaces,usage complete all as specified and directed by Engr-in-charge. Make: Asian Ultima protek/ Nerolac excel Excel top guard / Berger Paint weather Coat long life offering ten years guarantee

M&L for old decorated surface of wall, applying two coats of oil bound distemper with interior emulsion paint on walls over a coat of primer with mechenical sprayer followed by roller and filling gaps with putty to make surface upto desired finish as approved by Eng-in-charge complete all as specified and directed.

M&L for injecting at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 50mm centre to centre and sealing the same complete all as specified and directed.height of hole to be measured for payment perpuse.

M&L for treatment of soil under existing floors using emulsion at the rate of one litre per hole 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match with the existing floors complete all as specified and directed by Engr-in-charge

Taking up or down steel tubing 15mm bore and connection including cleaning for refixing or removal to store complete all as specified and directed by Engr-in-Charge.

Description all as per item No 64 herein before but 20mm dia complete all as specified and directed by Engr-in-Charge.

Supplying and laying 16mm dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed by Engr-in-charge

Description all as per item No 66 here-in-before but 20mm dia complete all as specified and directed by Engr-in-Charge.

S&F in repair counter top WHB including cutting for and pinning in brackets but excluding waste pipecomplete all as specified and directed by Engr-in-Charge.

S&F in repairs for 15mm dia of pipe bib taps cast copper alloy, fancy type, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr-in-charge

S&F for mixer taps cast copper alloy, fancy type with capstan head, CP, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nut, screwed for iron pipe 15 mm bore, supplied and fixed in repairs complete all as specified and directed by Engr-in-charge

S&F in repairs for 15mm dia of pipe angle valves ,fancy type and chromium plated brass with long shank and cup screwed both ends for iron pipes or for Unions and fixed .

Supply and fixing in repair, 20 mm dia gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engr-in-charge

S&F in repairs PVC connection 15mm diaand 45cm long with two Nos of brass checknuts and washers complete all as specified and directed by Engr-in-charge

S&F for stainless steel grating doom 125mm dia with waste hole complete all as specified and directed by Engr-in-charge

Supply and fixing of stainless steel towel ring complete all as specified and directed by Engr-in-charge

S&F in PVC (SWR) pipes of size 75mm dia with single socket joints fixed to floor with stack clamp and rubber ring joints complete all as specified and directed by Engineer-in-Charge

S&F in PVC (SWR) pipes of size 110mm dia with single socket joints fixed to floor with stack clamp and rubber ring joints.complete all as specified and directed by Engineer-in-Charge

S & F for PVC (SWR) bends of any radius with access door bore of pipe 110 mm complete all as specified and directed by Engr-in-charge

S & F for PVC (SWR) bends of any radius with access door bore of pipe 75 mm complete all as specified and directed by Engr-in-charge

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillet complete all as specified and directed by Engr-in-charge. Note :-Including Removal of debris or excavated material out of the defence line at govt approved dumping area and no extra cost will paid to the contractor against the same.

Providing and fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum ) False ceiling tiles of size 595 x 595 mm of approved texture, design and patterns having moisture contents less than 2% humidity resistance of 99% NRCO.50 to .75 as pe IS8225:1987, Noncombustible as per BS 476 (Part 4)-1970 and light reflectance of 85% (Minimum) to be laid in true horizontal level suspended on interlocking metal T Grid of hot dipped galvanized iron section of 0.33 mm thick ( galvanised @ 120 gms per sqm including both sides ) comprising of main T runners of size 15 x 32 mm of length 3000mm, cross -T of size 15 x 32 mm of length 600mm to form grid module of size 600 x 600mm, suspened from ceiling using galvaized mild steel items ( galvanizing @ 80 grams per sqm) i..e 50mm long, 8mm outer diameter M-6 dash fastener 6mm dia fully threaded hanger rod upto 1000mm length and L-swhape level adjuster of size 85x25 x 2mm galvanised iron permieter wall angle of size 24 x 24 x 0.40mm of length 3000mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450 mm ceneter to centre and 50mm long dry wall wood screws. The kwork shall be carried out as per specifications, drawing and as per directions of the Engineer-in-charge.

Re fixing false ceiling at all heights with exsiting False ceiling tiles of size 595 x 595 mm of approved texture, design and patterns having moisture contents less than 2% humidity resistance of 99% NRCO.50 to .75 as pe IS8225:1987, Noncombustible as per BS 476 (Part 4)-1970 and light reflectance of 85% (Minimum) to be laid in true horizontal level suspended on interlocking metal T Grid of hot dipped galvanized iron section of 0.33 mm thick ( galvanised @ 120 gms per sqm including both sides ) comprising of main T runners of size 15 x 32 mm of length 3000mm, cross -T of size 15 x 32 mm of length 600mm to form grid module of size 600 x 600mm, suspened from ceiling using galvaized mild steel items ( galvanizing @ 80 grams per sqm) i..e 50mm long, 8mm outer diameter M-6 dash fastener 6mm dia fully threaded hanger rod upto 1000mm length and L-swhape level adjuster of size 85x25 x 2mm galvanised iron permieter wall angle of size 24 x 24 x 0.40mm of length 3000mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450 mm ceneter to centre and 50mm long dry wall wood screws. The kwork shall be carried out as per specifications, drawing and as per directions of the Engineer-in-charge.

S&F for PVC (SWR) floor trap 100/75mm dia of outlet, plain with grating including jointing with solvent cement fixed in repairs.

Dismantling water tanks & removing to store exc 250 & n exc 500 litres complete all as specified and directed by Engr-in-Charge.

Supply & fixing Rotational moulded Polyethylene water storage tank - 500 liters (Triple layer)capacity (cylidrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I incl PTMT float valve 25mm dia complete all as specified and directed by Engr-in-Charge.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. & hositing if required reconnecting & re-fixing in position. (Cleaning repairing etc. measured separately).exc 500 & n exc 1000 litres complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old surfaces one coat of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of old painted surface complete all as specified and directed by Engr-in-Charge.

M&L Providing precast cement concrete fancy type louvers and jallies,25mm thick (measured solid), including allmouldings including frame with set in cement mortar 1:4 pcc type B0 1:2:4 (12.5mm grade aggregate) incl dismantling and removing defence land exc 5.00km complete all as specified and directed by Engr-in-Charge. Note :-Including Removal of debris or excavated material out of the defence line at govt approved dumping area and no extra cost will paid to the contractor against the same.

Dismantling of asbestos cement (corrugated, semicorrugated, etc) sheets in roof coverings complete all as specified and directed.

S & F for pre-painted galvalum aluminium zinc coating steel based corrugated steel sheet 0.50mm thick (total coated thickness) of any colour having tensile strength of 550 Mpa minimum, yeild strength, it shall be coated with hot dip alloy of 55% aluminimum, 43.5% zinc,1.5% silicon and finished with resin coat on both surface @ 150 gm/ sqm of coating as specified and shall be fixed with hot dip galvanised, self drilling and self tapping screws neoprened and EDPM washers as in roof covering all as directed at site complete all as specified and directed by Engr-in-Charge. Note- Fixing of sheet can be done in any shape( round/semicircle etc).

S & F for pre-painted galvalum aluminium zinc coating steel based plain steel sheet 0.50mm thick (total coated thickness) of any colour having tensile strength of 550 Mpa minimum, yeild strength, it shall be coated with hot dip alloy of 55% aluminimum, 43.5% zinc,1.5% Silicon and finished with resin coat on both surface @ 150 gm/ sqm of coating as specified and shall be fixed with hot dip galvanised, self drilling and self tapping screws neoprened and EDPM washers as in ridges, all as directed at site all as specified and dircted. Note- Fixing of sheet can be done in any shape( round/semicircle etc).

Dismantling wrought iron or mild steel work of any description as provided for Roof trusses, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) complete all as specified and directed by Engr-in-Charge.

M&L for MS framed structure roof trusses (framed), trussed, purlins,water tank stand, crane gantries and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats of Grade Fe 410 -W (Gde- E- 250) quality- A etc. complete all as specified and directed by Engr-in-Charge.

M & L for Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new/old painted surfaces of steel and iron work of any description over 10 cmwidth or girth not otherwise described and applying twocoat of synthetic enamel paint over a coat of redoxide on new surfaces in any tint complete all as specified and directed by Engr-in-Charge.

Removal of plants/trees of n.exc 30cm from roof tops/sides external walls of bldg. chajjas,wall juctions of rain water/CI soil/waste pipe juctions including taking out the roots entered in wall/slab surfaces and making food the disturbed surfaced using PCC (1:2:4) type B-0 or cement mortar (1:2) incl the preparation the GI/CI/PVC Pipe joints which were damaged during cutting/taking out process to match the existing and finishing the disturbed surfaces to match the existing incl necessary scaffolding/staging upto a height of 15.00mtr from the ground level complete all as specified as directed. (i) The debris incl vegetation plant/tree shall be disposed off to a distance exc 0.5 KM and n.exc 1 Km all as directed by Engr-in-Charge . (ii) For deciding the grith of the plant/tree the height shall be taken at 30 cm above the slabe/wall. (iii) The labour employed by the contractor for carring out the work shall be provided with equipment and quoted shall be deemed to include the same.

The quoted rates shall be deemed of include following provisions:- (i) Removal of plants/ trees of girth n ex 30 sc from roof tops/ sides, external walls of bldg, Chajjas, wall junctions, junctions of rain water/ CI soil/waste pipe junctions including taking out the roots entered in wall/ slab surfaces and making good the disturbed surfaced using PCC (1:2:4) type B-O of cement mortar (1:2) including repairing the GI/ CI/ PVC pipe joints which were damaged during cutting/ taking out process to match with the existing and finishing the disturbed surfaces to match with existing including necessary scaffolding/ staging upto a height of 15.00 m from the ground lever complete all as specified and directed. (ii) Any CI/AC/PVC pipes or pipe fittings damaged during the process of work shall be replaced by new one without any extra cost to the department . The decision of the GE in this regard shall be final and binding. (iii) The debris including vegetation plant/ trees shall be disposed off to a distance exc 0.5 Km and n. exc 1.00 km all as directed by engineer –in-charge. (iv) The labour employed by the contractor for carrying out above work shall be provided with safety equipment and quoted rates shall be deemed to include the same.

Schedule 'A' Part-II (E&M Works)

Taking down carefully unserviceable copper/aluminium point wiring (light, fan, socket or power)complete including fixture and fitting such as switches, ceiling rose lamp holder, regulators, sockets, light fittings, wooden terminal boxes, plastic laminated sheet cover, including taking down of DB’s, meter board any type all as specified and as directed.

M&L for point wiring with single core PVC insulated unsheathed 1100 volt grade cable with multi strand copper conductor of size 1.5 Sq mm FRLS (Nominal area) drawn through existing PVC conduit concealed in wall, ceiling with GI saddles GI screws, rawl plugs (concealed conduit wiring) with all fittings including Tee, Junction boxes and provision of pressed steel terminal box powder coated of suitable size with 3 mm thick laminated sheet cover for mounting switch sockets and regulators and drawing continuous earth wire of PVC insulated unsheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 Sq mm (Nominal area) complete all as specified. Note: Cost for cutting, chasing and making good to existing surfaces are deemed to be included in the Quoted Rate.

For one light point controlled by one SP switch

For one fan/exhaust fan and wall mounted fan point controlled by one SP switch.

Description all as per item No-99 above but for one 3 pin socket out let, 6 Amps on Independent board with the cable 1.5 Sqmm size complete all as specified and directed by Engineer-in-Charge.

Description all as per item No-99 above but for one 3 pin socket out let, 16 Amps on Independent board with the cable 2.5 Sqmm size complete all as specified and directed by Engineer-in-Charge.

S & F for socket outlet flush universal modular (piano) type 3 pin 6 Amps with suitable plate and cover complete all as specified and directed by Engr-in-charge.

S & F for socket outlet flush universal modular (piano) type 6 pin 16 Amps with suitable plate and cover complete all as specified and directed by Engr-in-charge.

S & F for switch Modular (piano) flush button single pole one way 6 amps with suitable plate and cover complete all as specified and directed by Engr-in-charge.

S & F for switch modular (piano) flush button single pole one way 16 amps with suitable plate and cover complete all as specified and directed by Engr-in-charge.

S&F for ceiling rose surface bakelite 2 to 3 terminals 65 x 50mm complete all as specified and as directed by Engineer-in-Charge.

S&F for energy saving decorative box type batten light fitting surface mounted complete with high efficiency PMMA diffuser soft glare free light LED lamp 18/20 watt suitable for 120 volts to 270 volts of system efficacy not less then 90 lumen/watt, with all accessories, pre-wired, including lamp and providing flexible copper wire, twin core cable complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for ceiling fans complete with aluminium blades, down rods, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)as specified, complete all as specified and directed by Engr-in-charge. Note : Taking down old existing ceiling fan and deposit to MES store without any extra cost.

Supply and fix for wall mounted fan complete with blades, hanging accessories, Pull chain control and accessories,1350rpm, 230V, 400mm size sweep min air delivery 72CMM air delivery complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engineer-in-Charge.

Supply and fix for stepped type electronic fan regulator flush type on the phenolic laminated sheet etc as required complete all as specified and directed by Engineer-in-Charge.

M & L for sub main wiring with two single core FRLS, PVC insulated, stranded, unsheathed cable copper conductor with size 06 Sqmm and drawing through & including Non metallic PVC conduit concealed in wall including earth continuity conductor of size 06 Sqmm PVC insulated unsheathed stranded copper conductor cable and connected to earth dolly to be drawn in ccocealed PVC conduit including connecting to main board complete all as specified and directed by Engineer-in-Charge. Note:- Conduit will be measured and paid separately.

S & F rigid non metalic PVC conduit 25 mm exclusives of boxes but incl all Tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles and pipe hooks etc complete all as specified and directed by Engineer-in-Charge.

S & F rigid non metalic PVC conduit 20 mm exclusives of boxes but incl all Tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles and pipe hooks etc.complete all as specified and directed by Engineer-in-Charge.

Distribution board iron clad VTPN DB, double door vertical type with IP-43 1K-09 protection suitable for MCCB as incommer and MCB as outgoing 415 Volts 3 phase 50 C/s 4 way, complete with appropriate size copper bus bar. Make-Legrand Cat pt No 5077 30 or equivalent of make L&T / Merlin Gerin multi-9 complete with rupturing cap 25 KA of the same make as of distribution board & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge. Note: MCB's and MCCB will be measured and paid seperately under relevent items.

S&F sheet metal enclosures for MCBs, single pole and neutral, 12 ways 240 Volts double door type complete all as specified and directed by Engineer-in-Charge.

S&F MCB SP 6 to 32 Amps, 240 Volts complete all as specified and directed by Engineer-in-Charge.

S&F MCB SPN upto 40 to 63 Amps ,240 Volts complete all as specified and directed by Engineer-in-Charge.

S&F MCCB TPN 125 Amps ,415 Volts complete all as specified and directed by Engineer-in-Charge.

M & L for earthing complete with galvanized steel earth plate electrode 60 x 60cm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 mtr deep below GL with top edge of the plate not less than 1.5 mtr below normal GL and connected to earth plate surrounded by 15 cm thick packed layers of charcoal dust and common salt and connected to earth lead galvanised iron lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvd iron or steel and thimbles and other end of the earth wire connected to DB and protected by galvd iron or steel pipe light grade 15 mm bore and water pipe 20mm bore GI light grade with funnel and wire mesh, including all necessary excavation and earth work PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover and all as shown in electrical plate No 3 of MES schedule Pt I of 2009. Note : RCC pit cover shall be pre-cast of RCC (1:2:4) type B-I , 80mm thick reinforced with XPM weighting not less than 4 KG/sqmm in lieu of CI cover.

Supply and fixing PVC insulated, armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 35 sq. mm 3.5 core complete all as specified and directed by Engr-in-charge.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth and getting out in any type of soil for laying of LT UG cables complete. Note:- The Rate quoted deemed to including cutting and removal of PSP Sheets wherever occured during excavation and the same shall be staged at desired location complete all as specified and directed by Engr-in-charge.

Returning, filling in, including spreading levelling, watering and well ramming in layers not exceeding 25 cm thick in hard dense soil complete all as specified and directed by Engineer-in-Charge.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed by Engineer-in-Charge.

Dry coarse sand as cushioning to under ground cable provided with layer of 8 cms deep before laying the cable and 15 cms deep after laying and stretching the cable, punned to 18 cm thick complete all as specified and as directed by Engr-in-Charge. NOTE Only punned thickness shall be measured for payment purpose.

Sub class 'B' old size bricks well burnt as covering to under ground cables , laid dry, flat over the cables on sand cushioning with width equal to length of the brick as mechanical protection to cable, complete all as specified and directed by Engr-in-charge.

Rakesh Kumar Malia (BID ID -3494786)

M/s Sunny Gupta (BID ID -3489942)

M/S MOHAN LAL SHARMA (BID ID -3495788)