SPECIAL REPAIR TO BLDG NO P-108, P-109, P-110, P-112 N P-115 OF TYPE-III, P-123 N P-124 OF TYPE-II AND P-231 OF TYPE-I AT ITR COLONY BALASORE

Amount

Dismantling of tile work any size in floors and wall laid in cement mortar including stacking material within 50 metres lead.

S&F Glazed Ceramic floor tiles of size 400mm x 400mm x 7-8mm thick of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, over and including 20 mm thick screed bed in cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.30 Kg/ sqm including pointing the joints with white cement and matching pigments etc. complete all as specified and directed.

Description complete all as per item No 2 here in before but in skirting, risers of steps and dados, over and including 10 mm thick backing of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.30 Kg per sqm, including pointing in white cement mixed with pigment of matching shade complete all as specified and directed.

S&F 450mm x 300mm x 7-8mm thick 1st quality ceramic glazed wall tiles conforming to IS: 15622 of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over and including 10 mm thick backing of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.30 Kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

S&F Non skid Ceramic floor tiles of size 300mm x 300mm x 7-8mm thick, in floors etc of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick screed bed in cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.30 Kg/ sqm including pointing with white cement and matching pigments etc., complete all as specified and directed.

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead, all complete as per direction of Engineer-in-Charge

M&L Polished Granite stone flooring in required design and patterns, with 16-18 mm thick stone slab over and including 20 mm thick screed bed of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with whitecement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc.all complete as specified and as directed by the Engineer-in-Charge. Note - Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

S&F for 20-22 mm thick Kota stone slab flooring over and including 20 mm thick screed bed cement mortar 1:4 laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete all as specified and directed by Engineer in charge

S&F for 18-20mm thick Kota stone slabs in risers of steps, skirting, dado and pillars laid over and including 10mm thick cement mortar 1:3 backing and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing all complete as specified and directed.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead, as per direction of Engineer in charge.

M&L for cement concrete flooring 40 mm thick 1:2:4 laid in positon with applying cement slurry (using 20mm size stone aggregate) including 38 mm wide glass strips panels of size n.exc 1.20mtr x 1.20mtr each or part there of finished even & smooth without using extra cement complete all as specified and directed.

M&L for Plain cement concrete 1:3:6 in sub base of floors (using 20mm size stone aggregate) complete all as specified and directed.

S&F for Chequered precast cement concrete tiles 300mm x 300mm x 25mm thick in footpath jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, over and including 20 mm thick screed bed of cement mortar 1:4 (1 cement : 4 coarse sand) complete all as specified and directed.

M&L for 75mm thick plain cement concrete 1:3:6 (type C1), using 20mm graded stone aggregate as in path, plinth protection or hardstanding and finished the surface even and smooth without using extra cement complete all as specified.

Dismantling of 15 to 40 mm dia G.I. pipe on wall/floor including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer-in-Charge

Supply and fixing 16 mm nominal dia Pipes Chlorinated Polyvinyl Chloride (CPVC) pipes SDR 11, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including necessary cutting chasing in masonry wall/column etc including testing of joints complete as per direction of Engineer in Charge.

Supply and fixing 25 mm nominal dia Pipes Chlorinated Polyvinyl Chloride (CPVC) pipes SDR 11, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement including testing of joints complete as per direction of Engineer in charge

Demolishing R.C.C. work over head RCC Water tanks manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer in charge.

Supply, fixing and placing on terrace polyethylene water storage tank 500 ltr capacity with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete all as specified.

S&F 20 mm nominal bore ball valve (brass) of approved quality, High or low pressure, with plastic floats complete all as specified.

S&F in 16 mm CPVC Ball Valve (Gate Valve) all as per specified and directed

S&F in 25 mm CPVC Ball Valve all as per specified and directed

S&F for Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position using structural steel etc. as required. In steel Door and Ventilator, frames, guard bar, ladder, railings, brackets, gates and similar works complete all as specified.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : (a) Of area 3 sq. metres and below

Supply and fixing in repair glass panes, with oil putty, nails and clips wherever necessary including racking out the old putty and hacking out old glass with Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm) and area not exceeding 0.50 sqm in each pan complete all as specified and as directed by engineer in charge.

S&F for Louvard ventilator are made out of uPVC manufactures by ISO 9001:2015 (QMS) certified company & tested as per IS 13360, multi-cavity frames Sections of 60x60x2.5mm multi cavity section suitable reinforced with G.I. and welded in corners and 5mm thick forsted glass can be fixed on alumimum louvard blades complete all as specified and directed by engineer in charge.

S&F for Single or multi shutter turn openable type windows (both gauzed and glazed) are made out of uPVC manufactures by ISO 9001:2015 (QMS) certified company & tested as per IS 13360, multi-cavity frames Sections of 60 x 60 x 2.5mm & addon frame of 60 x 40 x 2.3mm for mesh & Grill suitable reinforced. Multi-shutters Divison are made by using shash mullion having 50 x 64 x 2.5mm and 60 x 40 x 2.3mm multi-cavity uPVC section, suitable reinforced with G.I. and shutters are made out of 60 x 74 x 205mm uPVC section, reinforced and welded in corners with TPE Gaskets provision for 5mm thick Glass and for airtight at frames and outer side of shutter with single Glaze window shutters and using suitable glass bead with perfect hardware like hinges, handles, stays etc complete. Mosquito mesh shutter is made out of uPVC extruded section of 55x38x2mm with G.I. chanel of 1.2mm thick, welded in corners. Stainless steel Mosquito wire mesh of 0.36mm nominal dia wire and avg width of aperture 1.40mm is fitted in shutter with proper required accessories Lick, Hinges. M.S. 12mm Round bar including painting are inserted in main frame & screwed by hidden screwing system with powder coating. etc. complete.

S&F Frame size 65 x 125 mm factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/ mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (cost of M.S hold fast/lugs or SS dash fasteners shall be deemed to be included in quoted rates). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Description complete all as per item No 28 here in before but Frame size 65 x 100 mm complete all as specified.

Description complete all as per item No 28 here in before but Frame size 45 x 70 mm for cup board complete all as specified.

S&F 30mm thick factory made single extruded WPC (Wood Polymer Composite) solid one side decorative and other side plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/sqmm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as per direction of Engineer-In?Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

S&F 30mm thick factory made single extruded WPC (Wood Polymer Composite) solid plain mosquito proof door skeleton shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (face) & 900 N (edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In?Charge. (Note: stainless steel butt hinges with necessary S.S screws and SS wire mesh shall be paid separately)

M&L for painting on old steel surface with one coat of synthetic enamel paint of approved brand and manufacture of required colour to give an even shade including preparation of surface complete all as specified and as directed.

S&F factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using SS. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer in charge.

S&F 30 mm thick plain PVC door shutters factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification.

M &L for one coat painting with oil type wood preservative of approved brand and manufacture includig preparation of surface : Old work (one coat)

M & L for new steel work painting with two coats of synthetic enamel paint and one coat of red oxide primer of approved brand and manufacture to give an even shade including preparation of surface complete all as specified and as directed by engineer in charge.

Dismantling wooden boardings thickness 10mm up to 25mm in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead

S&F factory made 18mm thick (cup board shutter) single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In?Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)

Dismantling wood work (Cup Board) in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead : Of sectional area 40 square centimetres and above

S&F new wooden fillets wherever necessary: 2nd class teak wood fillets. plain fillets, square, rectangular or triangular in section clean sawn secured with nails sectional area exc 13 and not exc 25 Sqcm complete all as specified and directed.

M&L for scantling Painting with oil type wood preservative of approved brand and manufacture including one coat of pink primer : New work (two coats) all as per specified and directed by Engineer in charge.

S&F 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes, shelves, racks, almirah, cupboard and drawer etc. including necessary nails,screws including beading etc. complete as per direction of Engineer in charge.

S&F 250x16 mm aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. all as per specified and directed by Engineer in charge.

S&F 125 mm long aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. all as per specified and directed by Engineer in charge.

S&F 150 mm long aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. all as per specified and directed by Engineer in charge.

S&F 150x10 mm aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. all as per specified and directed by Engineer in charge.

S&F IS : 12817 marked 100x60x2.50 mm stainless steel butt hinges (heavy weight) with stainless steel screws etc. all as per specified and directed by Engineer in charge.

Supply and fixing piano hinges overall width 35 mm SS. Piano hinges ISI marked IS : 3818 finished with nickel chromium plating grade 1 as per IS: 1068 and fixing with necessary screws etc complete.

S&F for Stainless steel (grade 304) wire gauze of 0.36 mm dia wire and 1.40 mm aperture on both sides fly proof wire gauze to door, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete all as per specified and directed by Engineer in charge.

S&F 150mm long oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete all as per specified and directed by Engineer in charge.

S&F aluminium hanging Twin rubber stopper floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

M&L for 15 mm cement plaster in two coats under layer 10 mm thick 1:4 cement plaster and a top layer 5 mm thick cement plaster 1:4 mixed with WPC as per manufacturer instruction and finish the surface even and smooth without using extra cement. (Note: WPC shall be measured and paid separately.)

M&L for 5 mm thick cement plaster on ceiling in cement mortar (1:3) and finish the surface even and smooth without using extra cement complete all as specified and directed.

M&L for 10 mm thick cement plaster in cement mortar (1:6) and finish the surface even and smooth without using extra cement complete all as specified and directed.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete all as specified and directed.

M & L for distempering (OBD) two coats on new work wall and ceiling including one coat of alkali resistant primer with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete including preparation of surface, as per manufacturer's specification complete all as directed by engineer in charge.

M & L for white washing on ceiling old work (one coat) white washing with lime to give an even shade including preparation of surface complete all as specified.

M & L for removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc and Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall old surface to prepare the surface even and smooth complete and including distempering old plaster surface with 1st quality two coats acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, over the one coat of alkali resistance primer of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour complete all as specified and directed by engineer in charge.

M&L for removing old cement base paint, by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. Finishing walls with two coats of Premium Acrylic Smooth exterior paint with Silicone additives of required shade (Two coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed by engineer in charge.

M & L for Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two) coat applied @ 1.67 ltr/10 sqm over and including one priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified.

Demolishion of brick work built in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

M & L for Half brick masonry Cement mortar 1:4 with fly ash bricks old size bricks with sub class 'B' bricks in superstructure above plinth level up to floor V level complete all as specified.

M & L for fly ash brick work with sub class 'B' bricks old size straight or curved on plan exc 6 m mean radious built in cement mortar 1:4 complete all as specified and as directed.

M & L for Finishing walls with water proofing cement paint of required shade : New work (Two coats applied @ 3.84 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete all as specified.

M & L for Finishing walls with water proofing cement paint of required shade : Old work (one coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat complete all as specified.

M&L for White washing with lime to give an even shade New work (three coats) including preparation of surface complete all as specified.

M&L for White washing with lime to give an even shade : Old work (two coats) complete all as specified.

S&F in repair stainless steel sinks grade-A SS 304 with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm with stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required complete all as specified and directed by engineer in charge.

S&F in repair Stainless Steel grade-A SS-304 sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm with stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required complete all as specified and directed by engineer in charge.

S&F in repair 15 mm nominal bore C.P. brass bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified.

S&F in repair wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste coupling of standard pattern, including PVC flexible waste pipe 450mm long and painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap complete all as specified.

S&F in repair 15mm dia C.P. brass stop cock (concealed) of standard design and of approved make complete all as specified.

S&F in repair C.P. brass angle valve for basin and flushing cistern 15 mm dia of approved quality complete all as specified.

S&F in repair 100 mm dia SS grating for kitchen wash hand basin and bathroom complete all as specified.

Dismantling C.I. or asbestos 100/75 mm rain water pipe with fittings and clamps including stacking the material within 50 metres lead complete all as specified.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls including necessary brackets clamps or laid in trenches complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls including necessary brackets clamps or laid in trenches complete all as specified and as directed.

S&F in repairs 40 mm bore PVC(SWR) pipes single socketed in any length with rubber ring joints, fixed to walls including necessary brackets clamps or laid in trenches complete all as specified and as directed.

S&F in repairs 110mm bore PVC (SWR) junction single (Single "T") equal or unequal with access door complete all as specified and as directed.

S&F in repairs 110 mm bore PVC (SWR) bends of any radius complete all as specified and as directed.

S&F in repairs 75 mm bore PVC (SWR) junction single (Single "T") equal or unequal with access door complete all as specified and as directed.

S&F in repairs 75mm bore PVC (SWR) bends of any radius complete all as specified and as directed.

S&F in repairs 40 mm bore PVC (SWR) bends/Elbow of any radius complete all as specified and as directed.

S& F in repairs 75 mm PVC Nahani Trap WOJ complete all as specified and directed.

S&F in repair water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cuttin gand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests complete all as specified.

S&F in repair EWC. pan with ISI marked white solid plastic seat and lid white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, cutting and making good the walls and floors wherever required complete all as specified.

S&F in repair for Health Faucet (ABS) with 1 Mtr. Tube & Hook complete all as specified and directed.

M&L in repair for CP brass Two Way Bib Cock complete all as specified and directed by engineer in charge.

S&F in repair 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc. complete all as specified and as directed by engineer in charge

S&F in repair 15 mm nominal bore with 45 cm length unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour complete all as specified.

S&F in repair for 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete all as specified.

S&F C.P. brass shower rose with 15 or 20 mm inlet : 150 mm diameter complete all as specified.

M & L for providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical 1155. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :3 mm thick including taking down old APP membrane. laid over & including 10 mm thick cement plaster of cement mortar 1:3 mixed with water proofing compound finished even and smooth surface all as specified and directed by EIC. Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation. Note :- WPC shall be measured and paid separately.

Supply only liquid integral water proofing compound (ISI marked) of approved make.

M&L for 25 mm thick PCC 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 10mm nominal size) complete all as specified and directed.

S&F in repair 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour complete all as specified.

S&F in repair PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms complete all as specified.

S&F in repair 20mm dia SS curtain rods of wall thickness 1.25 mm with two fancy type SS brackets fixed with brass screws and wooden plugs etc. wherever necessary complete all as specified.

Dismantling and stripping the damaged concrete of Column, beam, , and slab etc. including covering plaster by light chiselling and other manual methods until sound concrete surfaces come up. Any trace of loose plaster , oil / grease, and moss / funguses if any or other materials that might affect adhesion are to be removed by wire brushing. The entire exposed surface shall then be washed thoroughly with plenty of Clean water and then allowed to dry. Smooth concrete surfaces if any to be roughened mechanically.

M&L for exposing the corroded reinforcement completely along its full circumference, cleaned to remove all loose scale and corrosion deposit applying rust removing chemical followd by removing the rust by emergy paper and cleaning the area thoroughly by water and allow it to dry. Sand blasting to remove residual deposit if necessary as per directive of manufacturer's instruction. Make: (Dr FIXIT/Fosroc/SIKA)

Supply and Application of Epoxy Zinc Rich primer on the Prepared Reinforced surface by brush ,upto 4 storey height, the primer should have a minimum Specific gravity 1.75 , Minimum Wet film thickness/coat 100 microns & Dry film thickness/coat 40 microns. Minimum Adhesive bond strength with steel is 1.5 N/mm2. Make:-(Dr FIXIT/Fosroc/SIKA))

Supply and Application of New TMT bars of approved Brand of requisite diameter by electro welding on both the sides as per IS specification with the existing bar to required size and shape at the portion where the existing reinforcement has lost half of its sectional area followed by a coat of Epoxy Zinc rich Primer as per the specification mentioned in Item No. 102 here in before. Make:- (Dr FIXIT/Fosroc/SIKA)

Use and waste of Formwork of smooth finish surfaces of column , beam, fascia, slab etc. with required bracing / support including fixing and striking out after pouring of concrete at all levels with necessary scaffolding and staging complete all as specified and as directed.

Supply and Application Free flow non-shrink cementitious micro concrete to the Affected Beam, Column etc. where major spalling has taken place even the core concrete affected. The Micro concrete should have a Minimum 1day Compressive strength of 10 MPa and 28 days strength of 50 MPa, Minimum Tensile strength 2.0N/mm2 @ 28 days, Minimum Flexural strength 5N/mm2 @ 28 days tested as per BS4551 - 80, Expansion characteristics Unrestrained expansion As per ASTM C827 - 1987 1 to 4%. A general purpose Epoxy Bonding agent to be applied on the concrete surface before the application the mortar. The bonding agent should have minimum compressive strength 40 N/mm2 as per BS6319 Part 7. Minimum Flexral Strength 25 N/mm2 as per BS 6319 Part 3 and minimum bond strength as per ASTM C88111 N/mm2. Make :-(Dr FIXIT/Fosroc/SIKA Chemicals).

Supply and Application Two component structural grade polymer modified reinstatement mortar where local spalling has taken place or shuttering is not possible. The Mortar can be applied from a minimum of 5mm to 15mm thickness in smaller vertical pockets and upto 100 mm thickness in horizontal applications. The mortar should have a minimum Compressive strength 12 N/mm2 in 1 Day and 45 N/mm2 in 28days. Minimum Flexural strength should be 8N/mm2 in 28 days.A modified styrene butadiene emulsion for use as a bonding aid and gauging liquid for cementitious systems to be mixed with cement slurry before the application of microconcrete to be used @ 6 ltr/bag of cement. The Bonding agent should have minimum Compressive Strength 24 N/mm2. Minimum Tensile Strength 3.5 N/mm2. Minimum Flexural Strength 6.5 N/mm2. Note: The Rate is based on an avg thickness. Make:-(Dr FIXIT/Fosroc/SIKA Chemicals)

Supply and Application Two component high build polymer modified cementitious reinstatement mortar where local spalling has taken place or shuttering is not possible. The Mortar can be applied in thicknesses from 15mm to 40mm thickness in vertical and 25mm in overhead situations. The Mortar should have a minimum Compressive strength 7 N/mm2 in 1 Day and 20 N/mm2 in 28days. Minimum Flexural strength should be 4.5 N/mm2 in 28 days. Minimum Tensile strength should be 1.7 N/mm2 in 28days. A general purpose epoxy bonding agent to be applied on the concrete surface before the application of mortar. The Bonding agent should have minimum Compressive Strength 40 N/mm2 as per BS 6319 Part 2. Minimum Tensile Strength 15N/mm2 as per BS6319 Part 7. Minimum Flexural Strength 25 N/mm2 as per BS 6319 Part3 and Minimum Bond strength as per ASTM C881 11N/mm2. Note: The Rate is based on an avg. Thickness of 15mm. Make:-(Dr FIXIT/Fosroc/SIKA Chemicals)

M&L for applying Concure LP90 or equivalent over concrete and cement plaster as curing compound complete as per manufacturers instrcn and as directed by Engineer in charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand (zone-III) : 10 graded stone aggregate 40 mm nominal size)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry complete all as specified and as directed by engineer in charge.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150 x 100 mm size P type With fly ash brick old size bricks with sub class 'B' bricks complete all as specified and as directed by engineer in charge.

S&F in repair 110mm SWR Fitting Vent Cowl with wire mesh as per specified and directed by engieer in charge.

Taking down carefully copper /aluminium point wiring (light, fan,exhaust fan, call bell, socket oultlet) complete, including fixture and fittings such as switches, ceiling rose, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc.

M&L for Point Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc.including all necessary wall cutting for sinking's of boxes and making good disturbed surface to walls all as directed and specified by Engr-In-Charge.

M & L for point wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way piano type switches, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. including all necessary wall cutting for sinking's of boxes and making good disturbed surface to walls all as directed and specified by Engr-In-Charge.

Taking down carefully copper /aluminium wiring including sunken MS boxes for 5A and 16 A socket wiring complete by unscrewing from board carefully and making good disturbed surfaces of wall, floors etc complete all as specified & directed by Engr-In-Charge.

M & L for Point Wiring for power plug for 15A indepenent switch socket board and on the same board with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required by Engr-In-Charge.

M & L for Point Wiring for 05A indepenent switch socket board with 2X1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 1.5 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required by Engr-In-Charge.

M&L for point wiring for One 3 pin socket outlet 5 amps on the same board with other switches wiring with copper conductor (FRLS) PVC insulated unsheathed cables of size 1.5 mm2 2 run and one run of 1.5 mm2 for earth continuity to be drawn in PVC concealed conduit non metallic not less than 20 mm width MS sheet metal switch / terminal box 1.2 mm thick and Hylum sheet switch including all necessary wall cutting for sinking's of boxes and making good disturbed surface to walls all as directed and specified by Engr-In-Charge.

Supplying and fixing metal box of size100mm X 100mm X 60mm deep (nominal size) made out of 1.6mm thick sheet, on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required by Engr-In-Charge.

Supplying and fixing metal box of size 150mm X 100mm X 60mm deep (nominal size) made out of 1.6mm thick sheet, on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required & directed by Engr-In-Charge.

Supplying and fixing 3 pin 5/6 A socket outlet on the existing switch box/ cover including connections to board as required all as specified & directed by Engr-In-Charge.

Supplying and fixing 6 pin 15/16 A socket outlet on the existing switch box/ cover including connections etc. as required & directed by Engr-In-Charge.

Supplying and fixing 5/6 A switch on the existing switch box/ cover including connections etc. as required by Engr-In-Charge.

Supplying and fixing 15/16 A switch on the existing switch box/ cover including connections etc. as required & directed by Engr-In-Charge.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required & directed by Engr-In-Charge.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required & directed by Engr-In-Charge.

Supplying and fixing PVC batten/ angle holder including connection etc. as required & directed by Engr-In-Charge.

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required & directed by Engr-In-Charge.

Taking down Sub main/Sub circuit wiring of any type and size including conduit/capping casing/batten wiring for necessary repair/replacement.

M&L for submain wiring using two runs of FRLSH grade PVC insulated unsheathed stranded copper conductor cable of size 6 sqmm and one run of 6 sqmm FRLSH grade PVC insulated unsheathed stranded single core copper earth wire to be drawn in and including at least 25 mm size PVC conduit(medium grade) in Concealed wiring of suitablebsize dolly complete all as specified and directed by Engineer-in-Charge. Note :- 3 Run of 6sqmm cable and PVC couduit shall be measured as one unit

Taking down ceiling fan and painting with one or more coats of spray painting with super enamel synthatic paint of approved brand and writing the MES No. on it as before and including cleaning of surface with detergent and replacing the damaged rubber reel, nuts and bolts with washers and safety pins, including hanging in at same location complete all as specified and directed by engineer in charge.

Taking down Unserviseable Sheet metal MCB/DB Box 6 way & 8 way & Main DB/Main switch etc for necessary repair/replacement complete all as specified and directed by engineer in charge.

Supplying and fixing of 4 way (4 + 12), Double door ways surface/ recess mounting, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, din bar for mounting MCBs (but without outgoing MCBs (SPN type) and incomer(TPN isolator) including all necessary wall cutting for sinking's of DBS and making good disturbed surface to walls all as directed and specified by Engr-In-Charge.

Supply and fixing 200A, 36KA rating and breaking capacity and four pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

Supply and fixing 125 A,36KA rating and breaking capacity and four pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required & directed by Engr-In-Charge.

Supplying and fixing 6 way Double door, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc.,making good disturbed sufaces of wall as required & directed by Engr-In-Charge. (But without MCB/RCCB/Isolator)

Supplying and fixing 8 way Double door, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc.,making good disturbed sufaces of wall as required & directed by Engr-In-Charge. (But without MCB/RCCB/Isolator)

Supplying and fixing 10A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of Single pole in the existing MCB DB complete with connections, testing and commissioning etc. as required & directed by Engr-In-Charge.

Supplying and fixing 20A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of Single pole in the existing MCB DB complete with connections, testing and commissioning etc. as required & directed by Engr-In-Charge..

Supplying and fixing 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of Single pole in the existing MCB DB complete with connections, testing and commissioning etc. as required & directed by Engr-In-Charge..

Supplying and fixing 16 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of Single pole and Neutral in the existing MCB DB complete with connections, testing and commissioning etc. as required & directed by Engr-In-Charge..

Supplying and fixing 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of Single pole and Neutral in the existing MCB DB complete with connections, testing and commissioning etc. as required & directed by Engr-In-Charge..

Supplying and fixing 40 A rating, double pole(SPN), 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required & directed by Engr-In-Charge..

Supplying and fixing 63 A rating, double pole(SPN), 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 100A rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required & directed by Engr-In-Charge.

Supplying and embedding 40 mm dia G.I. pipe (medium class) in pole collar/ foundation (during casting)/PCC /Hard standing/drain line cutting for cable entry including bending the pipe to the required shape complete with making good distrurbed surfaces of walls, floors etc as required & directed by Engr-In-Charge.

Laying and fixing only of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of upto 35 sq. mm (clamped with 1mm thick saddle) size on wall surface as required & directed by Engr-In-Charge.

S&F Building security light fitting of capacity 45 watt New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08. Make:- Havells cat No.ENDURASUNDOWNSL45WLED765PASYBOPC or equivalent in Crompton/ Philips)

Supply & Fixing of GI pipe bracket of 40 mm dia grade pipe bend to shape of approx length 1.5 mtr including 2 no MS clamp of flat iron size 40×6 mm complete with nut bolt washer all as specified & directed by Engr-In-Charge.

Materials and labour for earthing as in repair complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised strip of size 32 x 6mm by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe 40 mm bore (medium grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on completion all as specified and as directed by the Engr-in-Charge.

Laying only of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of upto 35 sq.mm size direct in ground including excavation, sand cushioning, protective covering(bricks) and refilling the trench etc and making good disturbed surfaces of floors,ground etc. as required and as directed by the Engr-in-Charge..

S&F 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Supplying, fixing and making straight through joint with cast resin compound including ferrules and other jointing materials for 4x25 sq.mm size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Supplying, fixing and making straight through joint with cast resin compound including ferrules and other jointing materials for 4x35 sq.mm size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

S&F basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver 20 W,4ft tube light along with fixture. Make: Havells cat No.LUMILINENEOBS20WLED865SPCWH or equivalent in crompton/philips

S&F LED lamp 15 W 3 star rated with minimum 500 lumen output, B22 holder complete all as specified and as directed. Make: Havells bulb cat No. LHLDDEEEML8R015 or its equivalent in Philips/Wipro

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core including taking down of existing cable and making good to match with existing surface after laying/fixing of new cable complete all as specified and directed by engineer in charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 4 core including taking down of existing cable and making good to match with existing surface after laying/fixing of new cable complete all as specified and directed by engineer in charge.

RANA ENTERPRISES

NIRMAL SALES CORPORATION

CHHABINDRA KUMAR PRADHAN

NARESH KUMAR BEHERA

Komal Buildcon Pvt. Ltd.

M P TYAGI ENGINEERS AND CONTRACTORS

national engineering

M/s Singh enterprises