PROVN OF DEFICIENT SECURITY ROOM FOR SHIV SAGAR DAM P 415 AND ADDN ALTN AND SPECIAL REPAIR TO ASHIYANA P 406 AND PROVN OF ADDITIONAL EXTERNAL LIGHTING AT ASHIYANA ROAD AT INS SHIVAJI LONAVLA

Amount

Demolition of Brickwork or stone/boulder masonry, built in Cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M&L for Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out hard / dense soil.

Excavation in trenches n.exc 1.5m wide, & n exc 1.5m deep and getting out in hard/dense soil.

Returning filling in, including, spreading levelling watering and well ramming in layers not exc 25cm in soft/loose soil etc complete.

Removing excavated material exc 100 m but n.exc 250 m and depositing where directed as in soils.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation and mass concrete.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter

M & L for RCC M30 (Design mix) for foundation beams, plinth beams, bases for columns etc basement slabs, under reamed piles and mass concrete.

M & L for RCC M30 (Design mix) for columns, pillars, piers, posts etc.

Formwork to sides of pillars, posts, struts, piers, columns, and stanchions

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

M&L for RCC M30 (Design Mix) for floor/roof beam supported on walls, beams and lintel above 1.5 m clear span complete all as specified

M&L for RCC M30 (Design Mix) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in the shelves and the like

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping)

M &L for RCC M 30 (Design mix)Fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels, balustrade, and the like

Formwork to fins, louvers, fascia for flat/ curved surfaces.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for coloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips on slab, MH cover etc. complete all as specified and directed by Engineer-in-charge.

All as per item above but bars of 17 mm dia

M&L for RCC in chajja type B1 1:2:4 complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges

M&L for aluminium three track, three shutter (of equal width) sliding type window without sash bar including necessary jointing clip, rubber packing, neoprene rubber gasket, locking arrangement (star lock) bearing (two no's for each sliding shutter ) &4 mm thick plain glass for glazing with for two shutters and aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire stapless complete all as specified and directed for one shutter & including following powder coated section as given in 'JINDAL' catalouge complete all as specified and as directed (i) Frame (Bottom) -20620, (ii) Frame top & Side - 20621, (iii) Shutter Vertical (Handle Lock) - 20846, (iv) Shutter Vertical -(int lock) - 20845, (v) Shutter (Top) - 20844, (shutter Bottom) - 20847

M&L for Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe Fe 290 Gde E-165 ,complete all as directed

M&L for pre-cast cement concrete block masonary with solid blocks, exc. 10 cm in width and setting in CM 1:4 complete.

M&L Brick work with sub-class `B' bricks, straight or curved on plan exc 6m mean radius built in cm 1:6

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:6

M&L Rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces.

M&L Rendering to celing concrete surfaces in CM 1:3(5mm) thickness

Supply of material for Integral waterproofing compound for external plaster

M&L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 25 cm thick, spread, levelled and rammed including watering all as specified and directed

M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M&L for 75 mm thick PCC (1:3:6) type C 2 (usin 40 mm gradded stone aggregate) as in plinth protection

M&L for vertified ceramic tiles 10mm (light shade of square/ rectangular) polished, area of each tiles not exc 0.36 sqm in floors etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 laying floor finishesed complete all as specified and directed.

M&L for vertified ceramic tiles 10mm (light shade of square/ rectangular) polished, area of each tiles not exc 0.36 sqm in walls skirting etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match including over 10mm thick rendering in CM 1:4 on fair faces of brick/concrete surfaces as in backing coat for tiles.complete all as specified and directed.

S&F machine cut and machine polished, green marble, 18-20mm thick in single piece as in double stepping on horizontal or vertical surface,as in window cills and jambs bedded, jointed and pointed with neat grey cement slurry and pointed with coloured or white cement with pigment to match over and including backing coat of rendering 10 mm thick in CM 1:4 all as specified and directed.

M&L for Rounding and moulding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and as directed.

S & F second class hard wood for Plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed

S&F 35 mm thick panelled shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified as directed.

M & L for preparation of new plastered surfaces of walls and applying Two coat of oil bound distemper including application of white cement based wall care putty finish (3mm thick) for smooth finish.etc complete all as specified and directed.

M&L for preparation of new plastered surfaces on walls, chajjas,filling of hair line cracks with white cement and applying two coats of 100% anti fungal weather resistant acrylic paint over a coat of acrylic primer in approved shade and as per manufacturer's instructions including necessary scaffolding complete all as specified and as directed.

M&L for preparation of new plastered surfaces on ceiling and applying three coat of white wash etc complete all as specified and directed

M&L for preparing new or previously untreated wood and wood based surface of any description, over 10cm in width or girth, not other wise described and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M/L for rendering 15mm thick in cm 1:4 on concrete roof and chajja surface to get a uniform level surface for laying of membrane treatment

M/L for applying oil based bituminous primer @ 0.10 Kg/Sqm providing and laying 4mm thick. APP modified water proofing membrane weighing not less than 4kg/sqm re-inforced with non woven polyester matt weighing not less than 160 gm/sqm having softening point not less than 140 degree centigrade longitudinal tensile strength not less than 650 N/Sqm, tearing strength of 180N and with thermal insulation with the mineral / graved finish on upper side and laying with torches application and with 10 cm minimum lap in both direction length wise and width wise all as specified and directed by Engr-in-charge.

S&F Butt hinges, cast ss, with mild steel hinge pin, bright polished and fixed, type B-11 of size

S&F aluminium handles cast type anodised 150 mm size.

S&F aluminium anodised barrel tower bolts of extruded section and fixed 200 mm size.

S&F aluminium anodised tubular curtain rod, 20mm dia, complete all as specified and directed.

S&F bracket for 20 mm dia tubular curtain rod(for item above) complete all as specified and directed

Demolition of concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

Demolition of RCC of any description and in any position not otherwise specifically provided reinforced (reinforcement of cut as required to facilasite demolition etc)as in column,chajjas , lintels and over head tanks etc removal of rubbish / demolished material out of MD land complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Taking down chowkats or frames n exc 1.5 sqm each with shutters (without taking off shutter from the frame) and removing to store.

Taking down chowkats or frames exc 1.5 sqm but n.exc 4 sqm each with shutters (without taking off shutter from the frame) and removing to store.

Non Skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

Glazed ceramic coloured tiles in vertical surfaces 350 x 250x 7 to 8 mm/ 450 x 350 x 7 to 8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match

Screed bed or bedding layer of mortar 15mm thick in CM (1:4) for laying floor tiles

Rendering 10 mm thick in CM (1:4) as in backing coat of cement plaster for laying of wall tiles

M&L for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tile exceeding 0.36 sqm but not exceeding 0.42 Sqm, in floors etc set & jointed in neat cement slurry & pointed in white or coloured cement to match the shade of tile over 15 thick cement screed bed in CM (1:6) complete all as specified and directed

Ditto all as item No 58 above but as in skirting to match floor finish with 15 mm thick backing coat of cement plaster in CM (1:4)

S&F 35mm thick 2nd class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a), supplied and fitted to chowkats complete all as specified and as directed.

S&F factory made PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube all as specified and as directed by EIC.

Providing and fixing 30mm thick "Rajshri" brand or equivalent factory made PVC Flush door shutter consisting of panel of Hollow PVC Profile of 20mm thickness, consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm inserted inside the hollow section of stiles, top and bottom rails and two 19mm x 19mm MS tubes inserted horizontally inside the hollow profile section at an equal distance from top and bottom of door and fixed with hollow profile section using 5mm thick PVC sheet using screws. Hollow PVC profile shall be lipped with 10mm (5mm x2) thick x 20mm width on stiles and rails using solvent cement. The inner panel shall be laminated with 5mm thick termite proof, water proof and fire retardant Prelam PVC sheet using solvent cement on both the sides of the panel etc. complete as per direction of Engineer-in-charge, manufacturer's specification and drawing

S&F aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed over windows with ms flat 20mm 4 mm thick and sutaible nails from out side of building complete all as specified and directed.

S&F aluminium handles cast type anodised 125mm size.

S&F aluminium anodised barrel tower bolts of extruded section and fixed 150 mm size.

S&F aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of sextruded sections or cast aluminium alloy and fixed 250mm length.

Taking down existing windows/ventilators (without taking off shutters and guard bars) of exe 1.5 sqm & n. exc 4 sqm etc complete all as specified and as directed incl stacking the materials properly.

S&F aluminium ventilator louvered type without sash bar section as per designation 63400 of IS 737 approved by GE( minium 15 micron anodised) including necessary jointing clip, rubber packing,including necessary locking arrangement , anodised snap beading screws and 4mm thick pin headed glass etc complete

M&L for machine cut Granite (of any type) tiles 20-25mm thick for kitchen platform ,double stepping on horizontal or vertical surface,as in window cills and jambs bedded, jointed and pointed with neat grey cement slurry and pointed with coloured or white cement with pigment to match over and including bedded and jointed with grey cement slurry/backing coat 15 mm thick in CM (1:4) and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types

S&F Stainless steel tubular curtain rod, 20-25mm dia, 1.25mm thick as fixed in repairs, complete all as specified and directed.

S&F acrylic cabinet mirror of size 450mm X600 mm fixed with wooden plugs with chromium plated screws and cup washers, complete all as specified and as directed.

Taking up or down steel tubing and connections, 15 mm bore including cleaning for re-fixing or removal to store

Taking up or down steel tubing and connections, 20 mm bore including cleaning for re-fixing or removal to store

Taking up or down steel tubing and connections, 25 mm bore including cleaning for re-fixing or removal to store

M& L for Cutting holes into or through brick/ stone walls built in cement mortar of superficial area n exc 150 Sq.cm and making good in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required

S & F Two piece EWC 680x360x765mm size white, with seat cover and Twin flushing cistern complete as per CERA -CAT No. S1021103 S Trap 230mm, CAT No S1060101 Cistern, CAT No B1510101 seat cover, CAT No B1810101 Twin Flush fittings all as specified and as directed. Note:- The rate quoted shall be include for taking down of all unserviceable existing item and stack them for issue under schedule of credit.

S& F Wash basin wall hung with half pedestal 550x400 mm as per CERA -CAT No. S2040103 wash basin and Cat No S2090102 Half pedestal complete all as specified and as directed. Note:- The rate quoted shall be include for taking down of all unserviceable existing item and stack them for issue under schedule of credit.

S & F Single lever basin mixer with 450mm braided connection pipe as per CERA CAT No. F1012451 complete all as specified and as directed. Note:- The rate quoted shall be include for taking down of all unserviceable existing item and stack them for issue under schedule of credit.

S& F flush pipe of polyethylene of low or high density or PVC, 32mm dia for low level cistern complete all as specified and as directed.

M & L for CPVC pipes, SDR 11, 32 mm outer dia conforming to IS-15778 with all fittings such as Tee, bends, elbows, unions sockets and end pieces etc to receive the fittings and fixed with solvent concealed in walls/ceiling or laying in floors complete all as specified and as directed.

Ditto as per Item No.80 above but 25 mm dia.

Ditto as per Item No.80 above but 20 mm dia.

M & L 32mm bore Brass chromium plated Bottle trap for wash basins with inlet and outlet screwed for pipe or connections incl necessary packing union and cap complete all as specified and as directed.

S & F PVC connection low density polythene pipe 15mm dia, 450mm long, heavy duty with PTMT nut completeall as specified and as directed.

S & F Waste coupling with ceramic pop up push type (full thread) 32mm as per Cera Cat No F8050351 complete all as specified and as directed.

S & F 15 mm bore pillar taps, with aerator as per CERA Cat No. QT F2006101 completeall as specified and as directed.

S & F Bib taps 15 mm dia, wih wall flange and aerator as per CERA Cat No QT F2006151 complete all as specified and as directed. Note:- The rate quoted shall be include for taking down of all unserviceable existing item and stack them for issue under schedule of credit.

S & F Stop valves 15 mm dia, quarter turn Concealed part as per Cera CAT No. QT F4050102 and exposed as per Cera CAT No. QT F2006351 complete all as specified and as directed. Note:- The rate quoted shall be include for taking down of all unserviceable existing item and stack them for issue under schedule of credit.

S & F Paper holder as per CERA -CAT No.F5007109 complete all as specified and as directed.

S & F SS soap dish as per CERA-CAT No. F5007103 complete all as specified and as directed.

S & F Hand shower Health faucet ABS body with wall hook and 1 metre SS braided rubber hose pipe as per CERA - CAT No.F8030102 complete all as specified and as directed. Note:- The rate quoted shall be include for taking down of all unserviceable existing item and stack them for issue under schedule of credit.

S & F 20mm dia Towel rail 600mm long as per CERA -CAT No.F5007103 complete all as specified and as directed.

M & L for Wardrobe shutter in double leaf(area not exc 2.20 sqm) with 18 mm solid PVC sheet incl edge fitted with auto close hinges 4nos per leaf, Godrej lock-1 Nos, Stainless steel handle-1 No per leaf,magnetic catcher 2 Nos per leaf all as per specified and directed by Engr-in-Charge Note:The rate quoted deemed to include for 100mm wide PVC sheet frame allaround of wardrobe for fixing auto hinges all as specified and as directed.

S&F in repairs MDF board, 18/20 mm thick exterior grade, pre-laminated both side decorative face lamination fixed with screws ,brackets to timber frame work with and including 1st class hard wood, edging 6 mm thick all around etc complete all as specified and as directed.

S &F Magic eye 10 to 12 mm internal dia suitable for door completeall as specified and as directed.

M & L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors 75 mm bore

M& L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors 110 mm bore

S & F PVC (SWR) bends any radius 75 mm bore

S &F PVC (SWR) bends any radius 110 mm bore

S & F PVC (SWR) junction single, (Single T) equal or unequal 75 mm bore

S &F PVC (SWR) junction single, (Single T) equal or unequal 110 mm bore

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement diameter of outlet 75 mm

S&F Swivel shower of PTMT any colour for fixing with15mm pipe. (Minimum weight 40gms)

S&F shower arm 15mm size,195mm long with bend of 45degree with flange of PTMT any colour.(Minimum weight 40gms)

S&F in repair brass Chromium plated wall mixer for mixing hot and cold water screwed down for iron pipe and fixed 15mm bore fancy type Make : CERA

S&F shower partition / bath cubicle made out of toughened glass 10 mm thick fixed and swing glass of any size alongwith all connected necessary items like wall to glass hinges (90 degree), two nos stainless steel handles, profile strips, magnetic strips (180 degree), floor brackets, stabilizer rod with 2 Nos wall end 1/2 Nos open end connectors

S&F Aluminium powder coated single leaf partly glazed and partly panelled door in two panels having 12mm thick MDF board both side laminated as bottom panel & 5mm thick toughened glass on top panel on pivots alongwith hydraulic door closer (Aluminium Extruded section), Brass door lock with four levers, 02 Nos of handles, with rubber beading and glazing clips and using following powder coated aluminium sections as given in 'JINDAL' Catalogue complete all as specified & as directed :- (a) Rectangular tube - 14005 (b) Shutter vertical - 19550 (c) Shutter top rail - 19563 (d) Shutter Middle rail - 19525 (e) Shutter Bottom rail - 19563 (f) Glazing clips - 19352 (g) Handle - 18566 Note:- The thickness of the powder coating shall not be less than 0.5 micron & the tint shall be as decided by GE.

Dismantling water tank of 1000 ltrs capacity, Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc and refixing after carrying out APP treatment with all accessories all as specified

S&F in repairs 1000 ltrs Rotational mould polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position all as specified in ssr part-I complete all as specified and directed.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty)with stranded aluminium conductor, 1100 volts grade, of size 3.5 core 240 sq mm.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty)with stranded aluminium conductor, 1100 volts grade, of size 3.5 core 70 sq mm.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty)with stranded aluminium conductor, 1100 volts grade, of size 3.5 core 35 sq mm.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty)with stranded aluminium conductor, 1100 volts grade, of size 4 core 25 sq mm.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty)with stranded aluminium conductor, 1100 volts grade, of size 2 core 16 sq mm.

Relaying Rerouting old cable of any size complete all as specified and aas directed.

S&F in replacement vertical type DB , (VTPN) suitable for and including MCCB 4 pole, 125 amps, 16KA as incoming (compact) Earth and neutral bus bar of capacity upto 200 amp 4 ways,IP 43 protection , shrouded neutral bar & pan assembly with flexible connecting link in the wall with suitable nut and bolt including matching the existing surface all as specified and directed ,

S&F in repairs MCB SP 6 to 32 amps single pole 240 Volts, Complete all as specified and directed.

Supply, fabricate, errect, connecting, testing & commisioning LT Panel, Outdoor Type, weather and vermin proof made out of 3 mm thick CRCA sheet with front & Rear opening and locking arrangement, epoxy powder coated having colour siemens grey, 1000 Amps capacity aluminium bus bar for phase, 3 No's and 1 No 500 Amp bus bar for neutral, mounted on epoxy insulator including neccessary copper control wiring, heat shrinkable, RYB coloured sleeves over bus bar for identification, earth shields, circular holes at bottom / top to receive incoming and outgoing cable, cable lugs, cable gland of sizes as required floor mounting angle iron frame made out mild steel angle iron of size 40 x 40 x 6 mm grouted on PCC (1:3:6) upto required height suitable for the following control/ fitments sensible for 3 phase, 50 Hz, 415 V system complete with and including following :- (a) Bus bar RYBN 1000 Amp capacity - 01 Set (b) MCCB 630 Amp 4 pole 36 KA 415 Volt ( Incoming) - 01 No (c) MCCB 630 Amp 4 pole 36 KA 415 Volt ( Outgoing) (d) MCCB 200 Amp 25 KA 4 pole - 04. (e) Digital timer 65 Amp 3 pole 230 Volt-01 No. (f) MCCB 63 Amps 16 kA 4 pole -03 No (g) LED Indicator lamp RYB - 05 Set (h) Digital multifunction meter (V, A, F, PF, KW, KVA)

Supply and lay in trenches / along the wall / floor pipes GI light grade of size 100 mm dia with and including all fittings and accessories including taking down old U/S pipe complete all as specified and and directed for cable protection

Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material heat Shrink type and accessories suitable for 3 ½ / 4 core XLPE, armoured, Aluminium conductor cable of size 50 to 120 sqmm,Indoor/Outdoor type complete all as specified and as directed.

Renewal/ Repairs to LT Panel Board of any size complete as mentioned below:- (I) Repair/ replacement of damaged hinges of each compartment (ii) Taking down existing bus bars cleaning with CTC applying with becktol red solution, providing bus bar insulation and refixing with new nuts, bolts, washers etc. (iii) Replacement of damaged copper flexible cable and fixing new copper flexible cable of suitable size for incoming and out going connections of each MCCB terminals to bus bars (iv) Replacement of damaged/ worn out/ loose connections/ cable lugs for incoming & outgoing cables (v) Replacement of u/s CT's, ammeters, Volt meters, Indication Lamps (01 Set each) including provision of new wiring for the same. Note : Ammeters and CT's shall be wired with 2.5 sqmm copper wire . (vi) Replacement of neoprene gasket for all doors of panel board. Note : i) Cost for replacement of spares are deemed to be included in the quoted rates. ii) The rate shall be deemed to be included for replacement of worn out rusted, Channels, hinges, bolts, split pins and cable lugs, cable glands and neoprene gasket with painting to all doors including raising of foundation to 0.3 M height etc. iii) Cost of replacement of MCCB's, Repairs to ACB's not included in the scope of work.

M&L for earthling complete with galvanized GI earth plate electrode of size 600x600x6.00 mm, buried directly in ground (earth pit not less than 2.25 mtr below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to galvanized earth lead wire 4.0 mm dia by means of volts, nuts, check nut and galvanized iron or steel including earth work in any type of soil, charcoal salt 15 cm around the earth plate as shown in electrical plate No 3 of SSR part1991,20 mm dia watering pipe medium grade 1.50 mtr long GI protection pipe light grade 15 mm dia from earth pit to main board (NOTE:- maximum length of GI protection pipe with each earth shall not be less than 7.5 mtrs) including necessary pit with cover , including testing on complition.

Excavation in trenches n. exc. 1.5 M in width and 1.5 M in deep for laying of pipes and getting out in Soft / loose Soil

Cutting bituminus road as per direction of Engr in Charge for laying of UG cable and match the existing road to the existing system.

M&L for providing dry river sand / crush stone dust for cushioning to UG cable including punning down of sand in layers all as specified. Note :- Cushioning will be measured and paid after punning down.

Supply and laying factory cast, unreinforced precast concrete cable cover factory made embossed the mark “LT CABLE” class LV type1 flat size 250x150x40 mm laid in trenches as specified and as directed.

Taking down carefully copper/aluminium point wiring (light, Fan, Socket or power) fitting such as switches, ceiling roses, pendents, regulators, sockets etc complete removing material to store for keeping in safe custody and making good disturbed surfaces of walls, floors etc all as specified as directed.

M&L for point wiring with PVC insulated FRLS and unsheathed cable 1.5 Sqmm (Nominal area) ISI marked stranded copper conductor single core including medium grade PVC conduit not less than 20mm dia for point wiring, concealed in wall / false ceiling modular metal flush terminal boxes cover plate with frame of required module and colour with all accessories including 1.5 Sqmm PVC insulated and unsheathed stranded copper cable to common earth and connecting to earth dolly including colour coding of cable shall be Phase- Red, Neutral- Black and Earth- Green complete all as specified and directed by for the following. One light-/form paint controlles by one switch.

One socket 3 pin outlet 5 amp on independent board.

One 3 pin socket outlet 5 amp on the same board board with other switches.

One Bell point

One light point with 2 way switch

All as per item No.128 above but one 3 pin socket outlet, 16 Amps on independent boards with cables 4 sqmm size complete all as specified and as directed.

Supply and fix in repairs modular switch 6 Amps one way, 1 module complete all as specified and as directed.

Supply and fix in repairs modular switch 6 Amps,two way 1 module complete all as specified and as directed.

Supply and fix in repairs modular socket 6 Amps, 2/3 pin combined 2 module complete all as specified and as directed.

Supply and fix in repairs modular switch socket combone 6 Amps/16 Amps, 2/3 pin combined 3 module complete all as specified and as dirceted.

Supply and fix in repairs modular bell push 1 way 16 Amps, 1 module complete all as specified and as directed.

Supply and fix in repairs bell multy music type complete all as specified and as directed.

Supply and fix in repairs modular fan regolator step type 120 V 2 module complete all as specified and as directed.

Supply and fix in repairs White cover plate with frame, 3 module

Supply and fix in repairs White cover plate with frame, 4 module

Supply and fix in repairs White cover plate with frame, 6 module

Supply and fix in repairs metal flush box 3 module

Supply and fix in repairs metal flush box 4 module

Supply and fix in repairs metal flush box 6 module

S&F in repairs LED tubelight fitting 40 Watt (Warm white) prewirered upto terminal block complete with all accessories and connecting up with twin core / .0076 flexible copper wire complete all as required at site and as directed by Engineer -in-Charge. Cat No BLTRU 40W WW Viva TMV of Bajaj or equivalent of Havells/Philips / Wipro.

Supply and fix in replacement of LED Tube light of 10 watt (2") (warm white) with batten integrated channel complete with all accessories pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed.Make:Bajaj CAT Part No BCLSB 10 WW (2ft) or equivalent to CG/Philips/Wipro complete all as specified and directed .

Supply & fix LED step light 4 watt in white powder coated cast aluminium body & IP 54 protection along with fixture, complete all as specified and directed at site.Make:Bajaj CAT Part NoBLSGV 4W LED WH or equivalent to CG/Philips/Wipro complete all as specified and directed.

S&F in repairs Surface mounted 43 watt 2 x 2 luminaire white powder coated CRCA housing with LEDs, Aluminium front frame with flat white high transmission acrylic cover complete with LEDs, driver and standard accessories including neccessary fixing arrangement complete all as required at site and as directed by Engineer -in-Charge. Cat No BCTBLS 43W ZT WH of Bajaj or equivalent to Philips /CG.

S&F in repairs LED downlighter 18 Watt powder coated white finish with drop down PC diffuser to deliver low glare illumination with optimized heat sink for efficient heat dissipation and seprate replaceable electronic driver including neccessary fixing arrangement complete all as required at site and as directed by Engineer -in-Charge. Cat No LED Down lighter,BPSLR 18w WW of Bajaj or equivalent to Philips /CG.

Supply & fix in repairs 45 W pressure die cast aluminium housing LED Building light secondary optics IP 66 protection including connection with two core twisted copper flexible cable, Make - Bajaj, Cat No - BRLEP 45W LED V2 or equivalent make of Havells /Philips/CG

S&F in replacemen MCB DB SPN 4 ways Acrylic door door with 240 Volt, 200 amps rated bus bar with all accessories flush in the wall including matching the existing surface all as specified and directed Cat Part Indoasian No-811816 or equivalent to Havells/Schnider/Legrand

S&F in replacemen MCB DB SPN 12 ways Acrylic door door with 240 Volt, 200 amps rated bus bar with all accessories flush in the wall including matching the existing surface all as specified and directed .Cat Part Indoasian No-811819 or equivalent to Havells/Schnider/Legrand

Supply and fix in repaire Residual current circuit breaker with overcurrent protection double pole of size matching with two 17.5mm module ( RCBO DP/ SPN) conforming to IS 12640 & IEC 61009-1, 240 V, 50 Hz, with 10KA short circuit capacity with earth leakage senstivity of 30 mA of rating 06-32 Amp 240 Volts AC including taking down the old unsv MCB/RCBO. complete all as complete all as specified and as directed.

Supply & fix exhaust fans metal body complete with and accessories 230 V,300 mm sweep including taking down old u/s exhaust fan and deposited to MES store complete all as specified and as directed.

Supply & fix fans ceiling complete with accessories 230 V,1200 mm sweep. BEE 5 star rated including taking down old u/s ceiling fan and deposited to MES store complete all as specified and as directed.

S&F submain wiring with unsheathed multi-stranded FRLS copper conductor cable 1100 volts grade drawn through in and including PVC rigid conduit medium grade of not less than 20mm dia with conduit accessories and concealed in wall/surface of ceiling for two runs of 6 Sqmm single core and one run of 6 Sqmm PVC insulated FRLS copper conductor for earth continuity wire complete all as specified and as directed. Note :- Two run of 6sqmm single core FRLS cable with one run of earth continuity conductor and PVC conduit and accessories will be measured as one length including cutting chasing in wall complete.

M&L for sub main wiring drawing through PVC casing and capping with two single core 4 sq mm and one run of 4 sq mm as earth wire of stranded copper conductor PVC insulated FRLS and unsheathed cable of 1100 volts grade all as directed. Note:- Three run of 4 sqmm FRLS copper cable and One run of PVC casing caping will be measured as one running meter.

S&F submain wiring with unsheathed multi-stranded copper conductor cable 1100 volts grade drawn through PVC Casing capping for four runs of 6 Sqmm single core and one run of 6 Sqmm PVC insulated copper conductor for earth continuity wire complete all as specified and as directed. Note :- Four run of single core cable with one run of earth continuity conductor and PVC conduit and accessories will be measured as one length including cutting chasing in wall complete.

Supply & fix AC Three phase static energy meter of accuracy class 1.0 ,3 X 240 V ,50 Hz with Backlit LCD display of rating 10 - 60 A (measures and displays KWH ,V, Current I, KW, pf last month history of KWH, MD in KW) with special features like TOD, temper logging, optical communication port display in absence of power, with transparent hinge type box complete all as specified and as directed.

S&F socket for Telephone connection complete all as specified and as directed.

M&L for Rigid non-metallic PVC conduit exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc concealed PVC Conduit pipe of size 20mm for telephone and cable TV connection complete all as specified and as directed.

MANISH VEDPRAKASH ARORA