Balance work for Construction of RCC 3 storied F and ES Station Building, RCC 5 storied Drill cum Hose drying Tower, Rain water harvesting system ,Under Ground Reservoir, Security Fencing with Heavy Duty Iron Gate at Lakhipur in Goalpara, Assam

Amount

Construction of Main Building(Civil Works)

Providing brick soling in foundation and under floor with stone / best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. a Brick on flat soling

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.00 m and removal of the same for in-situ reinforced concrete and plain concrete work in: (3.1.1.3) Columns, pillars, posts and strut a Square, rectangular, polygonal in plan or any shape like Tee / L etc. having plane vertical face ii Using 25mm thick plank

(3.1.1.4) Sides and soffits of beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties a For depth not exceeding 1.00 m ii Using 25mm thick plank

Providing and laying plain / reinforced cement croncrete works cement with coarse sand and 20 mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately). iUsing mixture machine B In super-structure from plinth level upto 1st floor level. ii Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. M20or Proportion 1:1/2:3

Brick work in cement morter with 1st class brick including racking out joints and dewatering if necessary and curing complete as directed in sub-structure up to plinth level. (b)In proportion 1:4

112 mm thick 1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding MS rod / Tor steel of column to be embeded in cement mortar and will be measured and paid separately). (a) In cement mortar in proportion 1:4 (1 cement : 4 sand)

Brick work in cement mortar with 1st class brick including racking out joints and curing complete as directed In superstructure above plinth level upto 1st Level (b) In proportion 1:4 (1 cement : 4 sand)

Providing and laying 25 mm thick damp proof course with cement concrete in proportion 1:1.5:3 with graded stone aggregate of 10 mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

Providing, fitting and fixing powder coated pressed steel door frame made of 1.25mm/1.6mm thick sheet of various sizes with necessary hinge jamb, lock jamb, headand steel base ties at the bottom of the frame. The whole frame shall be welded or rigidly fixed togather by mechanical means with base ties of pressed mild steel angle of size 20x20x1.25mm thick. Frame to be field up with 1:4:8 P.C.C. After fitting the frame with brick/concreteworks etc. complete as directed by the department for all levels. (b)1.6mm thick sheet (iii) size125mmx60mm (single rebate)

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered plywood face panels conforming to relevent IS code including oxidised iron butt hinges (100 mm x 75 mm x 3.5 mm) 6 nos. with necessary wood screws. (a) Decorative type face panel and block board core (i) 40 mm thick

Providing, fitting and fixing anodised aluminium windows and ventilators of standard sections without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6 mm x 3.15 mm lugs 100 mm long embedded in CC blocks 150 mm x 100 mm x 100 mm in 1:3:6 mix including providing and fixing device, locking arrangement, spring catch as required complete as specified and directed for all levels (cement concrete to be measured and paid separately). (a)Side hung and Top hung windows and ventilators (i)6 mm clear glass

(ii) 5 mm frosted glass

Providing welding, fitting, fixing, hoisting and fixing of roof trusses with purlin, bottom runner etc. fabricated out of a combination of two or all of the following sections: (i) square hollow sections (SHS/RHS) (ii) rectangular hollow section and (iii) MS black-tubes conforming to relevant IS code 1161-1968 as per approved design and drawing including MS cleat, base plate, bolts and nuts which ever required, including that required for fixing the ceiling and one coat of red oxide Zinc Chromate primer to all steel surface etc. complete as directed as per specifications. b) Using other ISI marked approved brand tube

Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) at all levels including fitting and fixing with self drilling, self tapping screws complete. (Roof trusses, purlins etc. to be measured and paid separately.) TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement

Supplying, fitting and fixing in position reinforcement bars conforming to relevant IS code for RCC work / RB walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level).

20 mm thick cement plaster in two coats, backing coat 10 mm and finishing coat 10 mm thick on fair side of brick / stone masonry walls for interior plastering up to 1st floor level including arises, internal round angles,not exceeding 80 mm girth and finished even and smooth including curing complete as directed. (b) In cement mortar 1:4

20 mm thick cement plaster in two coats, backing coat 15 mm and finishing coat 5 mm thick on rough side of single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles, chamfers and / or rounded angles not exceeding 80 mm in girth and finished even and smooth including curing complete as directed. (b) In cement mortar 1:4

Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement based putty for concrete / mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5 mm). (i) Thickness = 1.50 mm thick

(a) Applying one coat of cement primer of approved brand and manufacture on wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth

Extra over item no 13.4.1 above for every suibsequent coat of wall painting with acrylic emulsion paint of approved brand and manufacture (asian paint/Berger paint /ICI paint/J&N paint /Nerolac)

(a) Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on new wall surface (two coats) to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials

Finishing old / new wall with water proofing weather coat smooth anti-fungal premium textured exterior finish of Sandex Matt brand of Snowcem India Ltd. of required shade after clering and clearing the surfaces etc. including scaffolding complete as directed at all levels (two coats).

Applying primary coat over new steel and other metal surface over 100 m in width or girth after preparing the surface by throughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper. (a) With ready mixed "red-lead/ red oxide" primer.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture (Asian Paint / Berger Paint / ICI Paint / J&N Paint / Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. (i)Surfaces over 100 mm in width or girth (b) High gloss (Asian paint / Berger paint / ICI paint / J & N paint / Nerolac)

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department)

Providing ANTISKID tiles of approved quality size ,shape not less than 8 mm on floor skiting over a cement mortar bed 15 mm thick of 1:3(1cement:3 coarse sand ) of approved make fix with fix with fix-A-tile (chocksey/sika/pedilite /rouf /white cement complete at all level as specified and directed

Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls).

Providing, fitting and fixing MS grill of requiredpattern for windows / clerestory windows / opening with MS flats at required spacing in frame all round, square or round MS bars with round headed bolts and nuts or screws. (ii)Ornamental grill (c) Fixed to Brick work / PCC / RCC

Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantityetc. complete as directed and specified, including forest royality within a distance of 8.00 km (Forest royality shall be reimbrushed on production of necessary certificate from the forest authority duly countersigned by DFO concerned).

Providing polished granite slab of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in proportion 1:3 (1 cement : 3 coarse sand) including cutting where necessary finished with flush pointing with Fix-A-Tile Choksey / Sika / Pedelite / Rouf) / white cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of slab and as approved and directed by the Department).

Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete. (anodised to bright natural matt and satin finished). Butt hinge (V) 100 mm x 75 mmx4mm

Sliding Door bolts (i)300 mm x 16 mm

Tower bolts (ii) 300 mm x 12 mm

Door handle (iii)150 mm

Side Drain

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (I) Upto a depth of 2.00 m below the existing ground level (a) In ordinary soil

Providing brick soling in foundation and under floor with stone / best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. Brick on flat soling

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed in super-structure above plinth level up to 1st floor level. In proportion 1:4

15 mm thick cement plaster in single coat on rough side of single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80 mm girth and finished even and smooth including curing complete as directed. (a) In cement mortar 1:4

20 mm thick cement plaster in two coats, backing coat 10 mm and finishing coat 10 mm thick on fair side of brick / stone masonry walls for interior plastering up to 1st floor level including arises, internal round angles,not exceeding 80 mm girth and finished even and smooth including curing complete as directed. In cement mortar 1:4

Construction of RCC pavement specification and design as directed by concern department…………

Constuction of RCC approach road specification and design as directed by concern department………

SANITARY & WATER SUPPLY WORKS

Providing fitting and fixing white vitreous China pedestal type watercloset (European type WC pan 400 mm high) of Parryware / Hindware make with seat and lead, CP brass hinges and rubber buffers, 10 litre low level white china vitreous flushing cistern with fittings, CI / MS brackets, 40 mm dia. flush band with fittings including painting of fittings and brackets, cutting and making good the walls and floors whereever required. B) Hindware make (a) White (i) Water closet Green (Cat No.20079) (inclusive of seat cover)

Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) PEDESTAL BASIN (with pedestal) (A) Parryware Make (iv) Cascade NXT 550 x 440 with long Pedestal (Cat. No.C0404/C0380)

Providing fitting & fixing stainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately (B) Nirali (xi) Grace Plain Medium (Bowl Size - 450 x 375 x 190) Glossy

Providing fitting and fixing vitreous china flat back type lipped front urinal basin with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. (B) Hindware Make (a) White (iii) FB 610 x 410 x 380 (Cat. No.60002)

Supplying, fitting and fixing PVC pipes of 6.00 kg / cm² (Supreme / Prince) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G/L as directed and specified. In exposed surfaces or in trenches. 160 mm diametre

In exposed surfaces or in trenches (ii) 110 mm diametre

(iv) 75 mm diametreake

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme / Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G/L as directed and specified. In exposed surfaces or in trenches 110 mm diametre

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme / Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G/L as directed and specified. (a)In exposed surfaces or in trenches (ii) 110 mm diametre

(iv) 75 mm diametre

Supplying fiting and fixing PVC plain single tee of (Supreme / Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G/L as directed and specified. (a)In exposed surfaces or in trenches (ii) 110 mm diametre

(iv) 75 mm diametre

Construction of filter bed in soak pit including earth work in excavation of soil and then filling up of the trench with brick bats / charcoal covered with earth over a layer of AC plain sheet above brick bat filling complete as directed. (sizes of soak pit may vary depending on the sizes and capacities of the septic tank as well as the number of users as mentioned in the table).

Providing fitting and fixing 75 mm dia. PVC cowel of ISI make complete as directed and specified.

Construction of a inspection pit as directed.

Construction of a septic tank and soak pit (As per detailed estimate)

Providing fitting and fixing Decorative Mirror complete as directed and specified..(A) Parryware Make (b) Size 600mm x 450mm

Providing, fitting and fixing CP soap tray / soap dish complete as directed and specified. (ii) Agmeco Make (c) Econ (Cat.No.EN-00102)

Providing, fitting and fixing CP towel rail complete as directed and specified. (d) Agmeco Made (i) Cubin 600mm long (Cat. No.CB-00202)

Providing, fitting and fixing Chrome Plated towel ring complete as directed and specified. (a) Jaquar make (i) Continental towel ring square (Cat.No. ACN-1121)

Supplying fitting and fixing GI pipes of following sizes, with all necessary 'R' brand or similar approved GI fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, HW clamps etc. complete at all levels including below G/L as directed and specified. Exposed or in trenches (a) 50 mm diametre (i) Using Tata (Medium)

(b) 40 mm diametre (i) Using Tata (Medium)

(d) 25 mm diametre (i) Using Tata (Medium)

(II) Concelled (f) 15 mm diametre (i) Using Tata (Medium)

Supplying fitting and fixing CP bib cock 15 mm dia. of approved brand directed and specified. (GI and CP pipes will be measured separately). (II) Jaguar make Continental Bib cock long thread

Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid separately)Jaguar make, Continental / Clarion ,15 mm diametre (Angular stop cock with long thread)

Supplying and fitting fixing CP pillar cock of 15 mm diametre of approved brand as specified and directed. Jaguar make Long neck with areator

Supplying fitting and fixing Chrome Plated (CP) sink cock of approved brand as directed and specified. (GI and CP pipes will be measured and paid separately). Jaquar brand Continental / Clarion Sink cock with raised 'J' shaped swinging spout

Supplying fitting and fixing overhead adjustable Chrome Plated (C.P.) spray shower 15mm dia. of Sona make with wall flange as directed and specified.(pipes will be measured and paid separately) Jaquar brand Continental Shadow arm 190 mm long heavy coated body with wall flanges

Supplying fitting and placing plastic cylindrical vretical claused topd(PCVC)tank of sintex/ polycon/patton make .over the stagging with manhole cover with looking and cleanine arrangement including providing pads size as required for inlet and out let pipes 2000Lt capacity (a) Sintex make

Taurus make FRP composite stuructural vessel Iron removal filters of 100% rust proof vessels complete with Top& Bottom Stairners, Multiport Valves ,Quality filter media -e.g Treated Sand, Mno2, Barakar Sand Gravels & Pebbles.ISO NSF certified 4000Lt capacity

Construction of Boundary Wall with Security fencing

Construction of Heavy Duty Iron Gate with Gate post , etc

Drill cum Hose Drying Tower

Supplying, fitting and fixing in position reinforcement bars conforming to relevant IS code for RCC work / RB walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level). (b)ISI approved super ductile TMT Bar (i)TATA/SAIL

(d) Extra for each subsequent floor or part thereof above first floor level. Above G/F

Above F/F

Above S/F

Above T/F

© ISI approved MS rod

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.00 m and removal of the same for in-situ reinforced concrete and plain concrete work in: (3.1.1.3) Columns, pillars, posts and strut Using 25mm thick plank

(3.1..4) Extra for each subsequent floor or part thereof above the First Floor level as mentioned in item no. 3.1.1 & 3.1.3(b) Above G/F

Above F/F

Above S/F

Above T/F

(3.1.1.4) Sides and soffits of beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. For depth not exceeding 1.00 m. Using 25mm thick plank

(3.1.4) Extra for each subsequent floor or part thereof above the First Floor level as mentioned in item no. 3.1.1 & 3.1.3(b) Above G/F

Above F/F

Above S/F

Above T/F

(3.1.1.5) Flat surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. Floors etc. upto 200 mm in thickness. Using 25mm thick plank

(3.1.4) Extra for each subsequent floor or part thereof above the First Floor level as mentioned in item no. 3.1.1 & 3.1.3(b) Above G/F

Above F/F

Above S/F

Above T/F

(3.1.1.10) Staircase with sloping or stepped soffits including risers and stringers but excluding Landing. (Using 38 mm thick plank)

(3.1.4) Extra for each subsequent floor or part thereof above the First Floor level as mentioned in item no. 3.1.1 & 3.1.3(b) Above G/F

Above F/F

Above S/F

Providing and laying plain / reinforced cement concrete work in proportion 1:1.5:3 including dewatering complete as directed.Using mixture machine . In super structure upto first floor level,. Column, pillers, posts, struts, suspended floor …….. including preparing the top space and finishing of nosing.

(2.2.4) Extra over item no. 2.2.1, 2.2.2 and 2.2.3 for each subsequent floor one part three of above 1st floor level Above G/F

Above F/F

Above S/F

112 mm thick 1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding MS rod / Tor steel of column to be embeded in cement mortar and will be measured and paid separately). In cement mortar in proportion 1:4 (1 cement : 4 sand)

{4.1.14 (a)} Extra for brick walling for each subsequent floors or part these off above 1st floor level as mentioned in item no. 4.1.7 112 mm thick brick / RB wall Above G/F

Above F/F

Above S/F

Above T/F

15 mm thick cement plaster in single coat on rough side of single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80 mm girth and finished even and smooth including curing complete as directed.. In cement mortar in proportion 1:4

20 mm thick cement plaster in two coats, backing coat 10 mm and finishing coat 10 mm thick on fair side of brick / stone masonry walls for interior plastering up to 1st floor level including arises, internal round angles,not exceeding 80 mm girth and finished even and smooth including curing complete as directed. In cement mortar 1:4

(6.2.5) Extra over item no. 6.2.1 to 6.2.5 for interior plastering on ceilling and siffits of stair case upto 1st floor level …...………….. complete as directed. Above G/F

Above F/F

Above S/F

65 mm thick cement concrete floor consisting of 53 mm under layer of cement concrete in proportion 1:3:6 (1 cement : 3 coarse sand : 6 coarse aggregate of 25 mm and down) and 12 mm thick wearing coarse of cement sand plastering in proportion 1:2 laid in panels and finished with a floating coat of neat cement finish (using cement slurry for bond @ 2.75 kg per sqm of floor area) including curing etc. complete as directed.

Providing and laying 50 mm thick CC floor with metallic concrete hardener topping under layer of 35 mm thick cement concrete in proportion 1:2:4 (1 cement : 2 coarse sand : 4 coarse aggregate of 20 mm and down) and top layer of 15 mm thick of metallic cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 stone aggregate 6 mm and down) by volume with which metallic hardening compound of approved quality is mixed in the ratio of 4:1 (4 parts of cement : 1 part of metallic floor hardening compound of approved quality by weight) including finishing with curing complete as directed.

Brick work in cement morter with 1st class brick including racking out joints and dewatering if necessary and curing complete as directed in sub-structure up to plinth level. In proportion 1:4

15 mm thick cement plaster in single coat on rough side of single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80 mm girth and finished even and smooth including curing complete as directed. In proportion 1:3

Providing, fitting and fixing powder coated pressed steel door frame made of 1.25mm/1.6mm thick sheet of various sizes with necessary hinge jamb, lock jamb, headand steel base ties at the bottom of the frame. The whole frame shall be welded or rigidly fixed togather by mechanical means with base ties of pressed mild steel angle of size 20x20x1.25mm thick. Frame to be field up with 1:4:8 P.C.C. After fitting the frame with brick/concreteworks etc. complete as directed by the department for all levels. (b) 1.60mm thick sheet (iii) size 125mmx60mm (single rebate)

Providing, fitting and fixing anodised aluminium windows and ventilators of standard sections without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6 mm x 3.15 mm lugs 100 mm long embedded in CC blocks 150 mm x 100 mm x 100 mm in 1:3:6 mix including providing and fixing device, locking arrangement, spring catch as required complete as specified and directed for all levels (cement concrete to be measured and paid separately). Side hung and Top hung windows and ventilators.. 6 mm clear glass

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered plywood face panels conforming to relevent IS code including oxidised iron butt hinges (100 mm x 75 mm x 3.5 mm) 6 nos. with necessary wood screws. Non Decorative type face panel and block board core.. 40 mm thick

Providing and laying 25 mm thick damp proof course with cement concrete in proportion 1:1.5:3 with graded stone aggregate of 10 mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

Earth / sand filling in plinth in layers not more than 150 mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. (C)With silt (predominantly non plastic) by truck carriage including loading and unloading.

Providing welding, fitting, fixing, hoisting and fixing of roof trusses with purlin, bottom runner etc. fabricated out of a combination of two or all of the following sections: (i) square hollow sections (SHS/RHS) (ii) rectangular hollow section and (iii) MS black-tubes conforming to relevant IS code 1161-1968 as per approved design and drawing including MS cleat, base plate, bolts and nuts which ever required, including that required for fixing the ceiling and one coat of red oxide Zinc Chromate primer to all steel surface etc. complete as directed as per specifications. b) Using other ISI marked approved brand tube.

Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) at all levels including fitting and fixing with self drilling, self tapping screws complete. (Roof trusses, purlins etc. to be measured and paid separately.) TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement (iv) 0.60 mm thick

Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement based putty for concrete / mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5 mm). Thickness = 1.50 mm thick

Wall painting (two coats) with acrylic emulsion paint approved brand and manufacture (Asian paint / Berger paint / ICI paint / J&N paint / Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a)Acrylic Emulsion Paint approved brand and manufacture (Asian paint / Berger paint / ICI paint / J&N paint / Nerolac)

(a) Applying one coat of cement primer of approved brand and manufacture on wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Finishing old / new wall with water proofing weather coat smooth anti-fungal premium textured exterior finish of Sandex Matt brand of Snowcem India Ltd. of required shade after clering and clearing the surfaces etc. including scaffolding complete as directed at all levels (two coats).

Providing barge board of size 200 mm x 20 mm with 1st class local Hollock / Bonsum timber including fitting and fixing with necessary wood screws etc. complete.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture (Asian Paint / Berger Paint / ICI Paint / J&N Paint / Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter Surfaces over 100 mm in width or girth High gloss (Asian paint / Berger paint / ICI paint / J & N paint / Nerolac)

(d) Applying one coat of alkali resistance primer of approved brand and manufacture on wall surface after throughly brushing the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Providing, fitting and fixing MS grill of requiredpattern for windows / clerestory windows / opening with MS flats at required spacing in frame all round, square or round MS bars with round headed bolts and nuts or screws. Ornamental grill . Fixed to Brick work / PCC / RCC

ELECTRICAL WORKS(Main Building)

Wiring for light/ fan/ call bell point with 2x1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mm ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including 6 Amp flush type switch/ bell push (Anchor Penta/Gold medal /Kolor kany.Kom/ Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover ,ceiling rose (Anchor/Gold medal /Kolor kany.Kom / Havells or equivalent make as approved by the Deptt.) etc. complete as directed and specified by the Deptt.Short point upto 3.00 m length

Medium point up to 6.00 metre. Length.

Long point upto 10.00 m length

Supply and fixing 2.00mm average wall thickness heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in recessed system for light/ twin control light/ call bell/ fan point including providing and fixing switch box outlet box and paintaing etc as required: Medium point upto 6.00 m length

Long point upto 10.00 m length

Wiring for 5 pin 6 amp plug with 1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) including providing & fixing 5 pin 6 amp socket outlet (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) and 6 amp flush type switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) earthing the 3rd pin of the socket as required on the switch board in flat ISI marked casing 'n' capping system, when fitted on same board of light and fan.

Wiring for twin control light point with 1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface flat 19 mm ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) system, with 2 way 5/ 6 amp F/T switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.)Long point upto 10.00 m length

Wiring for 5 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including and fixing 5 pin 16 Amps flush type socket outlets and 16 Amps flush type switch ( Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.),GI/ MS switch board (ISI marked) with phenolic laminated sheet cover earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 2 mm thick 20 mm. dia. rigid low halogen SFT PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) Medium point up to 6.00 metre. Length.

Long point up to 10.00 metre. Length.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts ( Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in surface flat ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity. With 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in surface flat 19 mm casing system

With 2 x 6 sq. mm. + earth continuity with 1x 4 sq. mm. cable in surface flat 25mm ISI marked casing 'n' capping system

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) with earth continuity in surface/ recessed 2 mm thick rigid low halogen SFT PVC IS: 9537 Part - III conduit wiring system.With 3 x 6 sq. mm. + earth continuity with2x 4 sq. mm. cable in surface flat 25 mm ISI marked casing 'n' capping system..

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) .4.00 Sq.mm 2 Core armoured U.G. cable

Supplying and fixing of polished Brass Bracket of 18 S.W.G, 25 cm long cast back plate and brass lamp holder complete including connection as approved by the Deptt.)as required Without Lamp

Supplying and fitting of 18/20 watt LED lamp in the existing bracket holder as specified and directed by the Department.

Supplying with fitting & fixing of the following Street light luminaries complete with lamp in the existing pole including making necessary connection as approved by the Deptt.)with 2 ×1.50 sq.mm F.R. multistrand and P.V.C. insulated single core copper cable as specified and directed by the department.. Philips make) Type HGS120 2xTL5-54W EBP For lamp 2xTL5-54W.. / Havells make): LHRT05228033 For lamp 2x28W T5

Supply, installation & testing of G.I. Plate earth station with 600 mmx600 mmx6 mm heavy duty G.I. earth plate with necessary 40 mm dia. G.I. watering pipe with G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement with 300 mmx300 mmx6 mm hinged cover C.I. cover plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

Extra for using salt (5 K and Charcoal (96 K in G.I./Copper plate Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the deptt .

Supplying & laying of 8 SWG G.I.. earth drawn through 15 mm dia. Medium quality G.I. pipe from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

Supplying & laying of 8 SWG Copper. earth from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

Supply, fitting & fixing of Lighting Finial Arrestor made of 25 mm dia 300 mm long solid Copper tube having 85 mm dia. single prong at top and 3 mm thick base plate at bottom complete with fitting & fixing with Brass nuts & bolts on roof, RCC slab, top of column etc. as specified and directed by the deptt.

Supply, fitting & fixing 20 mmx3 mm Copper strips drawn on vertically or horizontally on building wall/parapet wall in surface system complete with supply of Brass Nuts & Bolts, Screws etc including riveting, soldering and making connection as approved by the Deptt.)with earth electrode copper strips and Lightning Arrestor etc. as specified and directed by the deptt.

Supplying including fitting fixing of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator]. Standard model 1400 mm Sweep. "ORIENT PSPO make) / Usha make)/ CROMPTON make)/ Havells/ ATC/ V GAURD make)

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. Trans Air 300 mm sweep (Crompton make)

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 double door surface mounting TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. 4 way TPN (4+12) double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 surface mounting SPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. 8 way SPN double door

Supplying with fitting and fixing single pole 10 KA 240/415 V, 50 Hz MCB of the following capacity complete with necessary connection as specified and directed by the Department. B series 6 A

Supplying with fitting and fixing DP 10 KA 240/415 V, 50 Hz MCB of the following capacity complete with necessary connection as specified and directed by the Department.32 A

Supplying with fitting and fixing 4 P 10 KA 415 V, 50 Hz MCB of the following capacity complete with necessary connection as specified and directed by the Department.40 A

Supplying including fitting and fixing bus bar chamber ( HPL/ GECO / or equivalent make) with 4 strips bus bar of length 350/450/600/900 mm made of aluminium alloy or wrought aluminium suitable for 100 amp capacity complete with all accessories including connection etc. as required complete

Supplying with fitting and fixing four pole 415 V handle operated on load change over switch (IP-20 protection) in powder painted sheet steel enclosure on angle iron frame of the following capacity complete with making necessary connection as specified by the Department. 63 A

Supplying including installation, connection as approved by the Deptt., testing and commissioning of SUBMERSIBLE PUMP SET 3 (Three Phase) with steel cable rope and submersible cable complete as directed and specified by the deptt. 3 HP 3 phase

Supplying and installation and commising of out door type sub station complete with transformer LT line with all fittings etc .

ELECTRICAL WORKS (Drill Tower)

Wiring for light/ fan/ call bell point with 2x1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mm ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including 6 Amp flush type switch/ bell push (Anchor Penta/Gold medal /Kolor kany.Kom/ Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover ,ceiling rose (Anchor/Gold medal /Kolor kany.Kom / Havells or equivalent make as approved by the Deptt.) etc. complete as directed and specified by the Deptt. Short point up to 3.00 metre. length.

Medium point up to 6.00 metre. Length.

Long point up to 10.00 metre. Length.

Wiring for twin control light point with 1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface flat 19 mm ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) system, with 2 way 5/ 6 amp F/T switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) . (c)Long point upto 10.00 m length

Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mm ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including providing and fixing 5/6 pin 16 Amps flush type socket outlets and 16 Amps flush type switch ( Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.),GI/ MS switch board (I.S.I. marked) with phenolic laminated sheet cover earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete.Long point upto 10.00 m length

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface flat ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) system including earth continuity. With 2 x 2.5 + 1 x 1.52 sqmm in 19 mm dia. rigid PVC casing caping conduit.

With 2 x 6.00 sqmm + 1 x 2.5 sqmm in 25 mm dia. rigid PVC casing caping conduits.

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . 10.00 Sq.mm 2 Core armoured U.G. cable

Supply, installation & testing of G.I. Plate earth station with 600 mmx600 mmx6 mm heavy duty G.I. earth plate with necessary 40 mm dia. G.I. watering pipe with G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement with 300 mmx300 mmx6 mm hinged cover C.I. cover plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

Extra for using salt (5 K and Charcoal (64 K in pipe Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the Deptt.

Supplying & laying of 8 SWG Copper. earth from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

Supplying and fixing of polished Brass Bracket of 18 S.W.G, 25 cm long cast back plate and brass lamp holder complete including connection as approved by the Deptt.)as required Without Lamp

Supplying and fitting of 18/20 watt CFL lamp in the existing bracket holder as specified and directed by the Department.

Supply, fitting & fixing of Lighting Finial Arrestor made of 25 mm dia 300 mm long solid Copper tube having 85 mm dia. single prong at top and 3 mm thick base plate at bottom complete with fitting & fixing with Brass nuts & bolts on roof, RCC slab, top of column etc. as specified and directed by the deptt.

Supply, fitting & fixing 20 mmx3 mm Copper strips drawn on vertically or horizontally on building wall/parapet wall in surface system complete with supply of Brass Nuts & Bolts, Screws etc including riveting, soldering and making connection as approved by the Deptt.)with earth electrode copper strips and Lightning Arrestor etc. as specified and directed by the deptt.

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 double door surface mounting TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. 4 way TPN (4+12) double door

Supplying with fitting and fixing single pole 10 KA 240/415 V, 50 Hz MCB of the following capacity complete with necessary connection as specified and directed by the Department. B series 6 A

Supplying with fitting and fixing DP 10 KA 240/415 V, 50 Hz MCB of the following capacity complete with necessary connection as specified and directed by the Department.32 A

Supplying with fitting and fixing four pole 415 V handle operated on load change over switch (IP-20 protection) in powder painted sheet steel enclosure on angle iron frame of the following capacity complete with making necessary connection as specified by the Department.63 A

Mozaharul Islam

MREEGEN SAHARIAH