Extension of security wall at divisional store, Renovation/Up gradation of staff quarters, Sub Division Store Building and installation of surveillance system and improvement of Illumination at divisional store Gladni Jammu

Amount

Renovation of Sub Division Store Building

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster

15mm cement plaster on the rough side of brick wall(1:4)

Providing and applying white cement based putty of specified thickness(1mm thick)

Distempering with oil bound washable distemper of approved brand including priming coat with water thinnable cement primer.

Finish walls with premiem acrylic smooth exterior paint of required shade on New work( two or more coats applied @1.43l/10sqm and including priming coat of water exterior paint)

Painting with synthetic enamel paint of approved brand (two or more coats)

Painting top of roof with bitumen of approved quality @17kg/sqm With bitumen of grade VG-10

10cm thick mud phaska of brick earth on roof led to slope and plastered with 25mm thick mud mortar mixed with bhusa and gobri leaping with 1:1 and covered with specified tile bricks grouted with cement mortar 1:3 and 2% of integeral water proofing compound

Providing gola 75x75mm in cement concrete 1:2:4

Making khurras 45x45cm

Renewing glass panes,with putty and nails(float glass panes of thickness 4mm)

Providing and fixing angle iron frame doors,windows and ventilator of MS

Providing and fixing fly proof wire gauge with nuts and bolt complete

Providing and laying in position cement concrete of 1:2:4

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS 15622 (thickness to be specified by manufacturer) of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3(1 cement: 3 coarse sand) and jointing with grey cement slurry @3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of Ist quality conforming to IS 15622 of approved make, laid on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) including painting the joints with white cement and matching pigment etc. complete

Cement concrete flooring 1:2:4 finished and curing complete

Electrification of rooms in all respects i.e power points,fan points,light point etc complete job

Providing and fixing white vitreous china pedestal type water closet (European type W C pan) with seat and lid, 10 litres low level white PVC flushing cistern , including flush pipe with manually controlled device (handle lever), conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. WC pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with CI brackets, 15mm C P Brass pillar tap, 32mm CP Brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. Wash basin size 630x450 mm with a single 15 mm CP Brass pillars tap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing Stainless Steel A ISI 304(18/8) kitchen sink as per IS 13983 with CI Brackets and Stainless Steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required. Kitchen sink without drain board: 610x460 mm bowl depth 200 mm

Providing and fixing 8 mm dia CP/SS Jet with flexible tube up to 1 metre long with SS triangular plate to European type WC of quality and make, as approved by Engineer-in-Charge.

Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fitting complete 32mm dia flexible pipe

Providing and fixing PTMT liquid soap container 109mm wide, 125 mm high and 112 mm distance from wall, of standard shape, with brackets of same material, with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing GI Pipes complete with GI fittings and clamps, including cutting and making good the walls. Concealed pipe including painting with anti corrosive bit mastic paint, cutting chases and making good the walls

15 mm dia. nominal bore

20 mm dia. nominal bore

Providing and fixing un-plasticised PVC connection pipe with brass unions 15 mm bore, 45 cm long

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI:12701(Sintex Make)marked, with cover and suitable locking arrangements and making necessary holes for inlet, outlet and overflow pipes but without fittings and base support for tank.

Providing and fixing 15 mm nominal bore C.P brass angle valve for basin mixer and geyser points, of approved make conforming to IS 8931

Providing and fixing PTMT soap dish holder having length of 138 mm. Breadth of 102 mm, height of 75 mm with concealed fitting arrangement, weighing not less than 106 gms.

Providing and fixing of 4ft long LED tube light 20watt ISI Marked of approved make, with all accessories complete, as per the directions of the Engineer-in-Charge.

Providing and fixing 12 “ dia exhaust fans with wiring, switches, etc. as per standard requirements, of approved make, with all accessories complete, as per the directions of the Engineer-in-Charge.

Supply and fixing CI Cover weight not less then 23kg

Single phase induction motor(0.5HP)

Providing and fixing brass bibcock

Supply and fixing brass ball valve,tank nipple and stock cock

Supply and fixing of rigid PVC rain water pipe on wall IS :13592

Supply and fixing of ceiling fans

Supply and fixing of rolling shutters of approved make having strength confirming IS: 4454

Providing of office table

Providing of office chair

Providing of visiting chairs

Providing and installation of Air conditioner with stablizer 2ton (split type)

Providing of racks

Providing of Air cooler for shift staff

Supply and fitting of LED flood light(200W) for illumination in divisional store premises(Make Crompton,Havells etc.

Supply of all in one computer with 1KVA UPS

Installation of surveilliance system at divisional store 8 CAMS Complete setup i.e including LED Monitor, wires etc.

Renovation of Staff quarters

Removing dry of oil bound distemper, water proofing cement paint and the like by scrapping and sandpapering and preparing the surface smooth including necessary repairs to scratches etc.complete.

EXTERIORFINISHING Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade,one or more coats on old work.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 meters lead : Of area beyond 3sqm.

Frames and trusses Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Salwood.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. First class kail wood 35MM.

Renewing glass panes, with putty and nails wherever necessary including raking out old putty: Float glass panes of thickness 4.0mm (weight not less than 10kg/sqm).

Plywood

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 125mm.

Providing and fixing aluminum handles ISI marked anodized (anodic coatingnot less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 100mm.

Providing and fixing aluminum tower bolts ISI marked anodized (anodiccoating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 100x10mm.

Providing and fixing aluminum tower bolts ISI marked anodized (anodiccoating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 150x10mm.

Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 meters lead With cement mortar 1:4 (1cement:4 fine sand) With cement mortar 1:4 (1 cement: 4 coarse sand).

Demolishing R.C.C. work manually /by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curingin: Cement mortar1:4 (1cemen t: 4 coarse sand).

Extra for brick work with common burnt clay bricks/ cement concrete bricks in super structure above plinth level upto floor five level.

Light Points complete

M/S HAMAYUN SARWAR KHAN (BID ID -2447659)

M/S AMAN KUMAR CONTRACTOR (BID ID -2450806)

M/S PEE ESS BUILDERS (BID ID -2446925)

M/S NEW ERA CONSTRUCTION (BID ID -2452427)

Rabia Shafqat (BID ID -2452309)

JASMEET SINGH (BID ID -2452123)

SATISH KUMAR GUPTA (BID ID -2451038)

M/S DASTGEER INFRA BUILDERS (BID ID -2450204)