Special repair and painting of existing Ty-IV QtrNo. H-120, Ty-V Qtr H-121, H-122 and H-123. SW_ Re-Roofing, fixing of blinds a curtains, Cup boards/ Cabinets, Gypsum board ceiling at H-123 Ty-V Bungalow at Megapode under SD-IV, PBND, APWD, Port Blai

Amount

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:

Asbestos Cement sheet

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead :

Of sectional area 40 square centimetres and above

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Of area 3 sq. metres and below

Providing wood work in frames , trusses, purlins, rafters etc sawn and put up in position with Superior hard wood Cat-II (A)

Providing and fixing pre-painted galvalume (PPGL) steel profile sheets AZ-150 of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd. or equivalent (size, shape and pitch of corrugation as approved by Engineer-In- charge) 0.50mm (+0.50%) total coated thickness with aluminium zinc coating 150 grams per sqm as per IS:277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns, sheet should have protective guard film of 25 micron minium to avoid scratches during transportation and should be supplied in single length up to 12 metres or as desired by Engineer-In-Charge. The sheet shall be fixed using self drilling/ self tapping aluminium screws (Xylan) of size (5.5X55mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

"Providing and fixing pre-painted galvalume (PPGL) steel profile sheets AZ-150 of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd. or equivalent roofing acessories 0.50mm (+0.50%) total coated thickness with aluminium zinc coating 120 grams per sqm as per IS:277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping aluminium screws complete."

Ridge plain(500-600 mm)

Extra for providing and fixing aluminium wind ties of 40x 5mm flat.

Providing and fixing in position eaves or facia board with 18mm thick WPC board of approved quality and 30cm wide including nailing etc complete as per the direction of Engineer-in-charge.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Providing and fixing storage cup -board made of 18mm thick HDF MDHMR, pre-laminated board (ISO: 14001: 201) with 60cm projection including fixing of shutters with all fittings like stinless stell butt hinges, ss tower bolt, ss handles, magnetic catcher with locking arrangements etc.(NOte: Only front face of cabinet unit shall be measured for payment purpose)

Providing and fixing 12mm thick timber Cat-I (A) wall panelling on existing frames with necessary nails/screws etc complete as per the direction of Engineer-in-charge (Frame work to be paid separately).

Providing and fixing timber Cat-I (A) frame work consisting of battens 50x25mm fixed with wooden plug and screws etc complete as per the direction of Engineer -In - charge.

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/ 120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :

Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Finishing walls with Acrylic Smooth exterior paint of required shade:

Old work (Two or more coat applied @ 1.67 Itil 10 sqm) on existing cement paint surface

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

One or more coats on old work

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked S.S butt hinges with necessary screws including panelling finished with two coats of melamine polish over a coat of honey/natural colour wood filler putty etc, including preparation and applying sand paper and finishing to a glossy matt finish etc complete.

Rubber wood 35mm thick shutters

Providing and fixing 18 mm thick, 150 mm wide pelmet of rubber wood, including top cover of 18 mm Rubco board, nickel plated S.S. pipe 20 mm dia ( heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm S.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet including finishing with two coats of melamine polishing etc. all complete.

Providing and fixing fabric polyster split type draw vertical blinds in windows with slat width 89mm and slat thickness 0.80mm of approved brand as per the direction of Engineer-in-charge.

supplyingand fixing curtain cloth of approved make and specified colour and design including sewing, provision for clipping, fixing to curtain holder etc complete as per the direction of Engineer -In- Charge.( Cost of curtain rods shall paid separately).

Providing and fixing ISI marked stainless steel sliding door bolts with necessary nuts and screws etc. complete.

Providing and fixing stainless steel tower bolts with necessary screws etc complete

Providing and fixing stainless steel handles with stainless steel screws etc complete

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :

Along the external wall below concrete or masonry apron us- ing chemical emulsion @ 2.25 litres per linear metre includ- ing drilling and plugging holes etc.: With Chlorpyriphos E.C. 20% with 1% concentration

Supplying chemical emulsion in sealed containers including delivery as specified.

Chlorpyriphos emulsifiable concentrate of 20%

Painting with oil type wood preservative of approved brand and manufacture :

New work (two or more coats)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

25 mm nominal dia Pipes

Providing and fixing CPVC gate valve of approved quality (screwed end).

25mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

15 mm nominal bore

Refurbishment of old single/triple seated sofa with upholstery using cushion of approved quality including providing top cover of satin or other cloth as approved and as per the direction of Engineer-in-charge.

Supplying 06 seater dining table with glass top, chairs of size 1.50x0.90 mtr.

Supplying Tea table of size 1.20x0.75x 0.42 mtr of good quality as per the direction of Engineer- in- charge.

Provididng side table for bed of HDF MDHMR Pre-Laminated board of 18mm thick size 0.60x0.60x0.70 mtr including fxing of drawers with all fittings like ss handles, drawer channel, locking arrangements etc as directed by Engineer-in-charge.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Supply of rubber pipe for watering of plant in garden area of 30mtr roll.

Providing and fixing curtain rods of 1.25 mm thick stainless steel with two stainless steel brackets fixed with brass screws and wooden plugs, etc., wherever necessary complete :

25mm diameter

Polishing in high gloss/matt finish melamine clear polish on wood work (Two or more coats on old work) on wood work in required color/wooden shade texture including smoothing the surface with required sand papers etc complete as per the direction of Engineer-in-charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory Yvindows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Frame size 65 x 100 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) window shutter, fixing with 100mm stainless steel butt hinges, 100 stainless steel tower bolt & 100 stainless stee handle and hooks & eyes of required size with necessary screws including glazing with 4 mm thick glass panes etc complete as per direction of Engineer-In- Charge.

Providing and fxing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For shutters of doors, windows & ventilators including providing and fxing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of pqwder coating 50 micron)

Providing and fixing mosquito net using aluminium mesh complete of approved quality as directed by the Engineer-in-charge including cost of mesh, fixing and other materials and labour charges.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.

With cement mortar 1:4 (1 cement : 4 fine sand)

Supply of garden table & chair set with armrest consisting of 4 nos chair with cushion and a centre circular tea table of make Arsh craft out door furniture or equivalent as per the direction of Engineer-In- Charge.

Supply of folding bed with mattress for adults of make fanoya fold away bed or equivalent, as per the direction of Engineer-in-charge.

Supply of double size bed cot of size 1.94x1.52m of timber Cat-I (A) of approved design as per the direction of Engineer-In- Charge.

Supply of mattress of size 78"x 60" x 6" of approved make (Kurlon bond plus or equivalent) as per the direction of Engineer-In- Charge.

Providing and fixing glazing in WPC door window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge .

4mm thick float glass panes.

ARJUN MANDAL

M/S A N KUMAR