Repair of PHC Building at Village Kithana In Kaithal Distt

Amount

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing in cement (HSR 8.5 (b))

Dismantling Concrete reinforced cement concrete with cleaning and straightening and cutting of bars if required (HSR 8.6 (e))

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position complete in all respects (HSR 10.82 + 10.95 (a))

Providing and laying 80mm thick ISI Marked interlocking paver blocks conforming to IS 15658 2006 / IRC SP 63-2004 of all shapes and colours in design mix cement M-40 over a bed of 30mm thick fine sand complete in all respect. (HSR 10.159)

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coasts of bitumen laid hot at 1.65 Kg per sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Tile terracing with one layer of tiles, 22.86 cm X 11.43 cm X 3.81 cm laid dry over a layer of mud mortar including grouting with cement sand mortar 1: 3 and top surface to be left clean. (HSR 13.14)

Base course of floors consisting of 100 mm thick lime concrete 1:2:8 and 100 mm sand or stone filling. (HSR 14.2)

Pvdg & fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in floors, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSONS. (HSR 14.91)

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete (a) Size of ceramic Glazed tiles 200 X 300mm(HSR 14.92 (a))

Painting two coats with synthetic enamel paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (HSR 16.5)

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work. (HSR 16.60)

Providing two coats of exterior acrylic emulsion paint. a) 2nd quality (HSR 16.79 (a))

Factory manufactured solid flush door shutters, with block board core as per I.S.No.1659- 1969 bonded with water proof type phenol formaldehyde synthetic resin,hotpressesd, conforming to I.S.2202 part I and II, fixed in position,including iron hinges,screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above,but including labour for fixing the same in position)- (iii) 35 mm thick (HSR 17.93 (a) (iii)- Note 17.18

Pdg. & Fixing D.I.Pipe complete with GI fitting and clamps, i/c cutting & making good the walls etc. (DSR 18.10) (i) 15 mm dia pipe

20 mm dia pipe

Wrought iron and mild steel (using angles, flats, square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors open able or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12)

Steel reinforcement TMT bars FE-500 EQR / FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights / depths / storeys / basements etc. Note: Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. (HSR 18.22)

Supplying and fixing glass panes including special metal sash putty of approved make (b) glass panes 4 mm thick, exceeding 40 sq dm areas. (HSR 18.30 (b))

Providing and Fixing Poly Carbonate Sheet 1.25mm thickness on Gates and grills excluding the cost of MS framework but including the cost of nut bolts, Welding rods complete in all respect as per irection of Engineerin- Charge. (HSR 18.43)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE EUROPEAN TYPE WATER CLOSET SUITE WITH CONCEALED ‘P’ or ’S’ TRAP with or without vent (as approved by the Engineer-in-Charge) and all other necessary fittings as fully described in item no.30.3 above. (HSR 30.6 (i))

Pdg. & Fixing in position best Indian make (ordinary) lavatory suites consisting of:- Lavatory invitreous chinaware size as given below (v) Size 560 x 450 mm with one top (HSR 30.41 (v))

Providing and fixing in position quality stainless steel sink built in draining board of size 600mm X 450 mm complete as described in item no.30.53 and 30.58 above (a) Size 600 x 450 x 200 mm (HSR 30.59(a))

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRROR mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall of chromium plated brass clamps with C.P. brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (a) Indian make (i) 600 mm x 450 mm(HSR 30.71(a)(i))

Providing and fixing HDPE water storage tanks of Sintex, Diplast, O.K. make with covers/lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in- Charge. (except civil work). (e)1000 Ltr. (HSR 30.119 (e))

Providing and laying 150 mm thick granular sub base consisting of drainage layer confirming to Table 400.1 Grading –III of MoRT&H 5th edition, mixing in a mechanical mix plant at OMC, carriage of mix material to the site of work, spreading in uniform layer with motor grader on prepared surface and compacting with vibratory power roller to achieve desired density complete as per clause No. 401 of MoRT&H specifications. Note: - 1.Only crushed metal material should be used. No local earth sand shall be used. The material finer than 425 micron shall have zero Plasticity Index (PI). 2. Material and operation manufacturing shall be approved by engineer.

Recovery Items:- The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer have been calculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specifications) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the price quoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned as under :- (i) Bricks bats @ 480 P. Cum

Good Bricks @ 4.50/- Each Note:- In case of any difference in the unit & nomenclature of any of the HSR Items of Civil, P.H. work depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable.

The Teg Bahadur Co-Op L/C Society Limited Siwan

THE DHIMAN CO OP L AND C SOCIETY