PROVN OF TOILET AND BATHROOM AT TOLICHOWKI COMPOUND WALL WITH BARBED WIRE AROUND GUDIMALKAPUR BATHING POINTS AT CERTAIN BLDGS AND SPECIAL REPAIRS TO COVERED DRAIN IN FRONT OF 383 BLOCK AND CERTAIN REVNUE WORKS AT MHMD AREA UNDER GE GOLCONDA

Amount

Demolition of cement concrete (Unreinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) all as specified and directed.

Surface dressing not exceeding 15cm deep and getting out in hard/dense soil all as specified and directed.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in deep and getting out in hard/dense soil all as specified and directed.

Excavating in over areas not exceeding 1.50m in deep and getting out in soft/loose soil all as specified and directed.

Excavating in over areas not exceeding 1.50m in deep and getting out in hard/dense soil all as specified and directed.

Excavating in post holes or similar holes, each not exceeding 0.5 Cum, getting out in hard/ dense soil, including filling of Plain cement concrete(1:2:4) type B1(20mm graded stone aggregate), returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, well ramming and removing surplus soil to a distance not exceeding 50m, complete all as specified and directed.

M & L Sand filling under floors, including spreading, levelling in layers and well ramming, watering as required all as specified and directed.

Returning, filling in, soil, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each all as specified and directed.

Removing excavated material to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L for Hard core using broken stone or boulders not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rolled/rammed to a true surface complete all as specified and directed..

M & L plain cement concrete (1:4:8) type D2 (40mm graded stone aggregate) as in foundations, filling, surface channels, drains and mass Concrete all as specified and directed.

M & L Plain cement concrete (1:3:6) type C1 (20 mm graded stone aggregate) in foundation ,cills and other similar bands, bed plates and the like including weathering, slightly rounded including necessary form work, complete all as speecified and directed.

M&L for Plain Cement concrete (1:2:4) type B1 20mm graded stone aggregate as in lintels up to 1.5m clear span, steps and other similar bands,string scourses,lacing courses,perapets and railings upto 60 cm in height, kneerlers,apex stones,bed plates,kerbs not provided water troughs and thelike including wethering,slightly rounded or chamfred angles and throating,as directed Note: Reinforcement shall be measured and paid separately.

M&L Plain cement concrete (1:2:4) type B0 (12.5 mm graded stone aggregate) as in coping including formed work complete all as specifed and directed.

M&L for Pre-cast reinforcedcement concrete (1:2:4) type B1 (20 mm graded stone aggregate) as in cover slab for manholes, benching to manholes/ SEPTIC CHAMBER, chullah hoods, chajjas, water troughs, mangers, shelves and similar articles etc., set in cement mortor (1:4) including necessary form work all as specefied and directed.

M&L for RCC (1:1.5:3) type A1 (20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

M&L brick work with sub class 'B' bricks old size straight or curved on plan exc 6 mtr mean radius built in CM 1:6 complete all as specified and directed.

M&L brick work with sub class 'B' bricks, old size, half bick thick, straight or curved on plan exc 6 mtr mean radius built in CM 1:4 complete all as specified and directed.

M & L Broken glass coping on top of walls in cement mortar 1:3, etc complete all as spd and directed.

Demolition of Reinforced cement concrete in suspended slabs, beams, lintels etc. in cement mortar or cement concrete (Reinforcement cut as required to facilitate demolition), etc complete all as specified and directed.

S&F 35 mm thick 2nd class hard wood glazed and gauged Skelton shutters, open, rebated and prepared to receive glass, gauze etc. divided in to square with plain chamfered or rounded mitered and rebated sash bars, any numbers, edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as per ISI and all as specified in SSR Pt – I, section -8 clause 8.24 (a), Supplied and fitted to chowkats all as specified and directed.

S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, in opening as per specification and drawing all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of M.S tubes for top and bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel moulded plain colour PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, & joined together with solvent cement, S&F in the frame at site as per specification and drawing all as specified and directed.

M&L Use and wast formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

S&F of Butt hinges, 100mm size extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B-21 complete all as specified and as directed.

S&F of extruded aluminium handles fabricated type anodised 150mm complete all as specified and as directed.

S&F of aluminium anodised barrel tower bolts, 200mm size of extruded section complete all as specified and as directed.

S & F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed

M&L mild steel TMT bars 10mm dia and over, cut to length bent to shap required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or securing with clips all as specified and directed.

S&F Mild steel TMT bars 6 to 8 dia, cut to length, bent to shape required, inlcuding cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia all as specified and directed.

S&F Mild steel TMT bars 5 to 8 dia, as in stirrups cut to length, bent to shape required, inlcuding cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia all as specified and directed.

S& F for angle iron including embeding in concrete and screwing etc. wind ties for; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wiremesh etc.) including all necessary drilling, bolting or riveting, etc.,and similar work conforming to Fe-290 Gde E-165etc complete all as spd and directed.

S&F of Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; complete all as specified and as directed.

S&F of steel ventilators with top hung shutter including hings, steel peg stay, complete all as specified and directed. Note: Steel ventilator frame with gauged and glazed shuttes will be measured and paid as one unit complete all as specified and as directed.

S & F Steel work in tubular trusses & vertical post including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade st-240complete all as specified and as directed.

S & F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 but n exc 10 cm long,Diameter of neck in 11 to 15 mm, etc complete all as specified and as directed.

S & F for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured),etc complete all as specified and as directed.

M&L Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed.

M&L Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.80 thick of any colour having tensile strength of 550 Mpa as in roof covering/ridge/ cladding to wall/vally gutter , fixed with self tapping screws as specified and directed.

M&L 75mm thick plain cement concrete (1:3:6) type C-2 (40mm graded stone aggregate) as in plinth protection, complete all as specified and directed.

M&L 75mm thick plain cement concrete (1:4:8) type D-2 (40mm graded stone aggregate) as in sub base of flooring/path all as specified andd directed.

M & L for 100 mm thick plain cement concrete (1:2:4) type B1 (20 mm graded stone aggregate) in sub base of flooring/ hard standing finished even and smooth without using extra cement, complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.06 Sqm but not exc 0.11 sqm in floors set and jointed in neat cement slurry and pointed in coloured cement to match the shade tiles including 15mm thick Screed bed or bedding layer in CM (1:6) all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surfaces 300x200x7mm thick set and jointed in neat cement slurry and pointed in white cement to match the colour of tiles including 10mm thick rendering in CM (1:4) on brick or concrete surfaces as in backing coat to receive tile all as specified and directed.

M&L Mechine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658 - 2006 of 60mm thickness , M-35 grade , with gery cement and no pigment etc laid over 50 mm thick sand cushioning including packing sides of pavement with PCC (1:2:4) type B, (20mm graded stone aggregate) complete all as specified and directed.

Demolition of Stone masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified and directed.

M&L for 10mm thick rendering in CM 1:6 on brick or concrete surfaces finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for Rendering 15mm thick in CM (1:4) on fair faces of brick or concrete surface of walls finished even and smooth without using extra cement all as specified and directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar (1:6) all as specified and directed.

All as per serial item No. 60 here-in-before but except stones *Note: - Serviceable stones obtained from demolition of stone masonary shall be used

M&L for Rendering 5mm thick in CM 1:3 as in ceilings surfaces finished even and smooth without using extra cement, complete all as specified and directed.

M & L for cement mortar 1:4, Flush pointing to random rubble masonary coursed or uncoursed etc, complete all as specified and directed.

M&L for Prepration of new plastered surfaces of walls and apply two coats of cement base paint over a coat of cement primer, complete all as specified and directed.

M&L for Prepration of new plastered ceiling surfaces and apply three coat of white wash, complete all as specified and directed.

M&L for Prepration of new plastered wall surfaces and apply three coat of white wash, complete all as specified and directed.

S&F 3mm thick figured glass, pin headed type and glazing with oil putty steel pins in squares not exceeding 0.50 sqm in each pane all as specified and directed.

M&L Preparation of new steel surfaces width or girth exceeding 10cm and apply two coats of synthetic enamel paint over one coat of redoxide primer all as specified and directed.

S&F low density polyethylene pipes (LDPE) 40mm bore of pressure rating 6 Kgf/sqcm to walls, floors etc., as in spouts for sunken slabs all as specified and directed.

S&F double layered ISI marked, white colour, Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 500ltr capacity hoisted and fixed in position complete all as specified and directed.

S&F double layered ISI marked, white colour, Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 1000ltr capacity hoisted and fixed in position, complete all as specified and directed.

S&F of Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20mm bore pipe all as specified and directed.

S&F Steel water tubing, 15mm bore, ‘medium grade’ galvanised, with all fitting, complete, to walls and ceilings or laid in floors, complete all as specified and directed.

S&F Steel water tubing, 20mm bore, ‘medium grade’ galvanised, with all fitting, complete, to walls and ceilings or laid in floors, complete all as specified and directed.

S&F 15mm bore Stop valves(angle cock), cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe or for unions all as specified and directed.

S & F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, complete all as specified and directed.

S&F Bib taps, cast copper alloy with crutch, screwed down, screwed for iron pipe 15mm bore or for brass ferrule all as specified and directed.

S & F Vitreous China squatting pan , "Orrissa" pattern size 580 X 440 mm white with intgrel footrest (excluding flushing cistern & flush pipe) including 'P' or 'S' trap complete including provision of cement concrete complete all as specified and directed.

S&F Vitreous china wash hand basin, white, flat back size 550 x 400mm, including cast copper alloy15mm pillar taps, waste, chain and plug and porcelain stopper, brackets, cutting for and pinning in ends of brackets or erecting stand and 32 mm waste pipe, complete, all as specified and directed.

S & F PVC valveless syphonic action type, dual operated, (ISI marked) flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe, complete all as specified and directed.

S&F Vitreous China urinals, bowl, flat back of size 465 X 355 X 265mm white,including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), etc complete all as specifed and directed.

S & F 32mm in waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and directed.

S & F 40mm in waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and directed.

S&F PVC connection (IS) 15mm dia, 60Cms long with PTMT nuts complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories),etc completed all as specified and directed

S & F PVC (SWR) 75 mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

All as per serial item No. 89 here-in-before but except pipes *Note: - Serviceable pipes obtained from taking down gutters and rain water pipes shall be used

S & F PVC (SWR) 110 mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S & F PVC pipe 40mm bore waste pipe (IS) to urinals complete all as specified and directed.

S & F PVC pipe 32mm bore waste pipe (IS) to wash hand basin complete all as specified and directed.

S&F PVC (SWR) bends any radius 75mm bore all as specified and directed.

S&F PVC (SWR) bends any radius 110mm bore, all as specified and directed.

S&F PVC(SWR) vent cowl 110mm bore all as specified and directed.

S & F sink with drainage board made out of stainless steel (Non Magnetic)1mm thick sheet for kitchen or laboratory with plugs, washers and waste pipe including cast iron cantilever brackets and connecting union to waste pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm all as specified and directed.

S&F 25mm size brass chromium plated shower rose with or without swivel joints including fixing to steel pipe or union all as specified and directed.

S&F of Aluminium anodized towel rail 600mm long, 20mm dia, D type complete all as specified and directed

S&F Gun metal globe or gate valve, with iron wheel head screwed both ends for iron pipe 20 mm bore dia all as specified and directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal with access door 110 mm bore all as specified and directed.

M & L 150mm bore Reinforced concrete pipes, class NP2, laid and jointed complete with collars, laid in trenches and jointed, complete all as specified and directed.

M&L Salt glazed stone ware pipe, 150mm bore, grade`A', laid in trenches and joining, complete all as specified and directed

M&L Plain cement concrete (1:3:6) type C2(40mm graded stone aggregate) as in bed to drain pipe 150 bore SWG pipe including packing under and haunching against the pipe after testing of pipe, complete all as specified and directed.

M & L Plain cement concrete (1:2:4) type B2, using 40mm aggregate in surface channel and drains etc. complete all as specified and directed.

M&L Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mitred/stopped ends etc.etc complete all as specified and directed.

M&L salt glazed stone wave gully traps square or rounded mouthed type & fix 150 x 150 mm fixed in cement concrete, complete, all as specified and directed.

S&F PVC (SWR) floor trap 75mm dia outlet, plain with grating including jointing with solvent cement all as specified and directed.

M&L Screwing existing GI pipe line upto 40 mm dia (in position) for insertion of new 'T' of branch connection/insertion of valve/insertion of flanges etc incl necessary jointing material complete all as specified and directed.

M & L House service bracket complete with 3.0m long G.I. pipe 40mm dia Med. grade, two nos 90 degree bends. including clamps, nuts and bolts etc and required electrical connections all as specified and directed

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium stranded conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed , 2 Core 4 sq. mm nominal cross section in service connections complete all as spcified and directed.

M&L Point wiring for one light point/fan point/bell point controlled by one switch with 1.5 sqmm multistrand copper conductor cable PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 1.50 sqmm PVC (FRLS) insulated unsheathed copper conductor single core cable ( green colour) as earth lead in and including non metalic rigid PVC conduit medium grade with appropriate size with all fittings (ISI Marked) suitable for Conceled type on stone/brick,masonary walls,roof etc including in new sunk box of required size and complete all as directed by Engineer-in-Charge & 2 mm thick plastic laminated sheet for housing switches sockets, regulators etc, including making good the disturbed surfaces to match with the existing specification ,complete all as specified and directed

M & L lamp holder, PVC/Polycaronate type insulated body with back plate suitable for battern fittings complete all as spcified and directed.

M&L switch piano flush type single pole one way 5 Amps complete all as spcified and directed.

S&F Sheet metal enclosure MCB distribution board including 200 Amps bus-bar single pole and neutral 240V, 2 Ways, including taking down of existing sheet metal enclosure complete all as specifide and directed.

S&F Ceiling rose surface 3 phase / PVC / polycarbonate,isolated body bakelite 65 x 50 mm 2/3 terminais complete all as spcified and directed.

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge o the plate not less1.5 mtrs below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts nuts, check nuts and washers of galvanized iron of steel all as shown in electrical plate No.3 connected to earthing test point incl necessary earth work, excavation PCC 1:3:6 type CI using 20mm graded stone aggregate for earth chamber provn of PCC cover 40 mm thick 1:2:4 mm type B1 funnel with water Pipe, GI pipe, 15mm dia medium grade protection pipe, GI earth lead complete all as spcified and directed.

S&F MCB single pole and neutral 6 to 32 Amps 240 Volts complete all as spcified and directed.

S&F LED tube light fittings 1 x 22 W, 230V, complete with all accessories internally prewired and including LED Tube rod connecting up with twisted flexible PVC copper conductor cable of 23/0.0076 from ceiling rose complete all as spcified and directed. (Make : Cat No.Havelles Code No : REGAL BATTENT8UPT01X22WSSBSWH (Batten) CRYSTAL1213T8DSTL18WLED865SGLASS(Tube Rod) or equivelent in Philips / Crompton Greaves)

S & F Bulk head fitting 10W luminaires with all accessories including lamp holders etc complete with one No 10 watts LED bulb and connecting up with twin core twisted flexible PVC copper conductor cable of size 23/0.0076 from ceiling rose complete all as spcified and directed.

m/s s indra reddy constructions