Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹42.8 LAccepted-AOC 29 MODEL TOWN BEHIND GURUDWARA PATHANKOT | PATHANKOT | PATHANKOT | PUNJAB | 145001 | ₹42.8 L Quoted ₹44.1 L | L1 | Accepted-AOC being L1 |
| 2 | L2₹44.5 LRejected-Finance GURDASPUR ROAD NEAR SAINIK MANDIR PATHANKOT 145001 PB | PATHANKOT | PATHANKOT | PUNJAB | 145001 | ₹44.5 L | L2 | Rejected-Finance being other than L1 |
| 3 | L3₹50.5 LRejected-Finance | ₹50.5 L | L3 | Rejected-Finance being other than L1 |
| 4 | L4₹53.8 LRejected-Finance | ₹53.8 L | L4 | Rejected-Finance being other than L1 |
| 5 | Rejected-Technical | - | - | Rejected-Technical renewal enlistment not uploded. Kindly upload fresh enlistment |
| Sl No | Description | Qty | Unit | SAINI AND SAINI BUILDERS L2 | kailu construction co L1 | BHARAT ENGINEERS L3 | SMT Construction L4 |
|---|---|---|---|---|---|---|---|
| 1.00 | Dismantling & Taking down existing panel & Supply, installation, fabrication, testing and commissioning of new LT Panel board, (CPRI type tested) Factory made cubical type, Outdoor type, floor mounted, factory made out of 50mm x 50mmx6mm angle iron frame and 3.15mm inner CRCA steel sheet side covers with front and back hinged doors with proper locking arrangement, rubber gasket on front and back to make it dust and vermin proof, powder coated including suitable rated aluminium bus bar sleeved with heat shrink sleeve colour coated for 3 Phase, 4 wire electric supply system and wiring with suitable size of 1200 amps (03 Nos 1200 Amps for Phase and 01 No 600 Amps for neutral) rated aluminium bus bar complete powder coated paint with and providing necessary foundation/plateform of the feeder pillar and provision for incoming and outgoing cable, cable gland, replacement of lugs for existing cables as per site requirement and proper finshing as per existing surface complete all as specified and directed by Engr- in- Charge:-
Note : (i) The quoted rate shall be of all inclusive.(ii) Drawing for LT feeder piller box shall be got approved by GE before fabrication.(iii) Platform for the feeder pillar board with PCC 1:2:4 15 Cm thick in foundation, Brick (Sub Class B) work in CM 1:6 ,rendering 1:6 , 10 mm thick on exposed surfaces and 100 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in padding on top and grouting legs of panel . The platform shall be of 60 cm below ground level and 60Cm height above ground level . Rate for Platform shall be included in the quoted rate with following:
(a) Incoming
(i) ACB 04 Pole 50 kA, 800 Amp,415 Volts (Qty 01 No).
(b) Out goings
(i) MCCB 04 Pole 50 KA, 630 Amp, 415 Volts, fixed thermal & magnetic release (Qty -01)
(ii) MCCB 04 Pole 36 KA, 315 Amp, 415 Volts, fixed thermal & magnetic release (Qty - 02 Nos /01 No standby )
(iii) MCCB 04 Pole 26 KA, 200 Amp, 415 Volts, fixed thermal & magnetic release (Qty - 02 Nos and 01 No standby )
(iv) Aluminium bus bar suitable size 3 phase, 4 wire 1200 Amp,415 V, duly insulated - set of 4
(v) Digital Volt meter 0-500V with slector switch.
(vi) Digital Amp meter 0-500 amp with CT and selector switch.
(vii) Indicating lamp (RYB)LED Type - set of 3 | 1 | Each job | 3,74,000 ₹3.7 L | 3,50,000 ₹3.5 L | 4,00,000 ₹4 L | 3,99,999 ₹4.0 L |
| 2.00 | Dismantling & Taking down existing panel & Supply, installation, fabrication, testing and commissioning of new LT Panel board, (CPRI tested) Factory made cubical type, Outdoor type, floor mounted, factory made out of 50mm x 50mmx5mm angle iron frame and 3.15mm inner CRCA steel sheet side covers with front and back hinged doors with proper locking arrangement, rubber gasket on front and back to make it dust and vermin proof, powder coated including suitable rated aluminium bus bar sleeved with heat shrink sleeve colour coated for 3 Phase, 4 wire electric supply system and wiring with suitable size of 800 amps (03 Nos 800 Amps for Phase and 01 No 400 Amps for neutral) rated aluminium bus bar complete powder coated paint with and providing necessary foundation/plateform of the feeder pillar and provision for incoming and outgoing cable, cable gland, replacement of lugs for existing cables as per site requirement and proper finshing as per existing surface complete all as specified and directed by Engr- in- Charge.
Note : (i) The quoted rate shall be of all inclusive.(ii) Drawing for LT feeder piller box shall be got approved by GE before fabrication.(iii) Platform for the feeder pillar board with PCC 1:2:4 15 Cm thick in foundation, Brick (Sub Class B) work in CM 1:6 ,rendering 1:6 on exposed surfaces and 100 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in padding on top and grouting legs of panel . The platform shall be of 40 cm below ground level and 60Cm height above ground level . Rate for Platform shall be included in the quoted rate with the followings:-
(a) Incoming
(i) MCCB 04 Pole 36 kA, 630 Amp,415 Volts, fixed thermal & magnetic release (Qty 01 No).
(b) Out goings
(i) MCCB 04 Pole 26 KA, 315 Amp, 415 Volts, fixed thermal & magnetic release (Qty - 01 Nos)
(i) MCCB 04 Pole 26 KA, 250 Amp, 415 Volts, fixed thermal & magnetic release (Qty - 02 Nos)
(i) MCCB 04 Pole 26 KA, 200 Amp, 415 Volts, fixed thermal & magnetic release (Qty - 02 Nos)
(ii) Aluminium bus bar suitable size 3 phase, 4 wire 800 Amp,415 V, duly insulated - set of 4
(iii) Digital Volt meter 0-500V with slector switch.
(iv) Digital Amp meter 0-500 amp with CT and selector switch.
(v) Indicating lamp (RYB)LED Type - set of 3 | 2 | Each Job | 1,77,000 ₹3.5 L | 1,80,000 ₹3.6 L | 2,09,000 ₹4.2 L | 1,97,828 ₹4.0 L |
| 3.00 | Dismantling & Taking down existing panel & Supply, installation, fabrication, testing and commissioning of new LT Panel board, (CPRI tested) Factory made cubical type, Outdoor type, floor mounted, factory made out of 50mm x 50mmx5mm angle iron frame and 3.15mm inner CRCA steel sheet side covers with front and back hinged doors with proper locking arrangement, rubber gasket on front and back to make it dust and vermin proof, powder coated including suitable rated aluminium bus bar sleeved with heat shrink sleeve colour coated for 3 Phase, 4 wire electric supply system and wiring with suitable size of 800 amps (03 Nos 800 Amps for Phase and 01 No 400 Amps for neutral) rated aluminium bus bar complete powder coated paint with and providing necessary foundation/plateform of the feeder pillar and provision for incoming and outgoing cable, cable gland, replacement of lugs for existing cables as per site requirement and proper finshing as per existing surface complete all as specified and directed by Engr- in- Charge. Note : (i) The quoted rate shall be of all inclusive. (ii) Drawing for LT feeder piller box shall be got approved by GE before fabrication. (iii) Platform for the feeder pillar board with PCC 1:2:4 15 Cm thick in foundation, Brick (Sub Class B) work in CM 1:6 ,rendering 1:6 on exposed surfaces and 100 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in padding on top and grouting legs of panel . The platform shall be of 40 cm below ground level and 60Cm height above ground level . Rate for Platform shall be included in the quoted rate with the folowing:-
(a) Incoming
(i) MCCB 04 Pole 36 kA, 500 Amp,415 Volts, fixed thermal & magnetic release (Qty 01 No).
(b) Out goings
(i) MCCB 04 Pole 36 KA, 315 Amp, 415 Volts, fixed thermal & magnetic release (Qty - 01 Nos)
(i) MCCB 04 Pole 26 KA, 200 Amp, 415 Volts, fixed thermal & magnetic release (Qty - 03 Nos)
(ii) Aluminium bus bar suitable size 3 phase, 4 wire 800 Amp,415 V, duly insulated - set of 4
(iii) Digital Volt meter 0-500V with slector switch.
(iv) Digital Amp meter 0-500 amp with CT and selector switch.
(v) Indicating lamp (RYB)LED Type - set of 3 | 2 | Each Job | 1,67,000 ₹3.3 L | 1,65,000 ₹3.3 L | 1,88,000 ₹3.8 L | 1,78,559 ₹3.6 L |
| 4.00 | Dismantling & Taking down existing panel & Supply, installation, fabrication, testing and commissioning of new LT Panel board, (CPRI type tested) Factory made cubical type, Outdoor type, floor mounted, factory made out of 50mm x 50mmx5mm angle iron frame and 3.15mm inner CRCA steel sheet side covers with front and back hinged doors with proper locking arrangement, rubber gasket on front and back to make it dust and vermin proof, powder coated including suitable rated aluminium bus bar sleeved with heat shrink sleeve colour coated for 3 Phase, 4 wire electric supply system and wiring with suitable size of 600 amps (03 Nos 500 Amps for Phase and 01 No 250 Amps for neutral) rated aluminium bus bar complete powder coated paint with and providing necessary foundation/plateform of the feeder pillar and provision for incoming and outgoing cable, cable gland, replacement of lugs for existing cables as per site requirement and proper finshing as per existing surface complete all as specified and directed by Engr- in- Charge. Note : (i) The quoted rate shall be of all inclusive. (ii) Drawing for LT feeder piller box shall be got approved by GE before fabrication. (iii) Platform for the feeder pillar board with PCC 1:2:4 15 Cm thick in foundation, Brick (Sub Class B) work in CM 1:6 ,rendering 1:6 on exposed surfaces and 100 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in padding on top and grouting legs of panel . The platform shall be of 40 cm below ground level and 60Cm height above ground level . Rate for Platform shall be included in the quoted rate with the following:-
(a) Incoming:
(i) MCCB 04 Pole 36 kA, 315 Amp,415 Volts, fixed thermal & magnetic release (Qty 01 No).
(b) Outgoing:
(i) MCCB 04 Pole 25 KA, 160 Amp, 415 Volts, fixed thermal & magnetic release (Qty - 05 Nos)
(ii) MCB TPN 10 KA, 16 Amp, 415 Volts, fixed thermal & magnetic release (Qty - 01 Nos)
(iii) Aluminium bus bar suitable size 3 phase, 4 wire 500 Amp,415 V, duly insulated - set of 4
(iv) Digital Volt meter 0-500V with slector switch.
(v) Digital Amp meter 0-400 amp with CT and selector switch.
(vi) Indicating lamp (RYB)LED Type - set of 3 | 2 | Each Job | 1,31,000 ₹2.6 L | 1,25,000 ₹2.5 L | 1,48,000 ₹3.0 L | 1,45,678 ₹2.9 L |
| 5.00 | Dismantling & Taking down existing panel & Supply, installation, fabrication, testing and commissioning of new LT Panel board, (CPRI type tested) Factory made cubical type, Outdoor type, floor mounted, factory made out of 50mm x 50mmx5mm angle iron frame and 3.15mm inner CRCA steel sheet side covers with front and back hinged doors with proper locking arrangement, rubber gasket on front and back to make it dust and vermin proof, powder coated including suitable rated aluminium bus bar sleeved with heat shrink sleeve colour coated for 3 Phase, 4 wire electric supply system and wiring with suitable size of 500 amps (03 Nos 500 Amps for Phase and 01 No 250 Amps for neutral) rated aluminium bus bar complete powder coated paint with and providing necessary foundation/plateform of the feeder pillar and provision for incoming and outgoing cable, cable gland, replacement of lugs for existing cables as per site requirement and proper finshing as per existing surface complete all as specified and directed by Engr- in- Charge. Note : (i) The quoted rate shall be of all inclusive.(ii) Drawing for LT feeder piller box shall be got approved by GE before fabrication.(iii) Platform for the feeder pillar board with PCC 1:2:4 15 Cm thick in foundation, Brick (Sub Class B) work in CM 1:6 ,rendering 1:6 on exposed surfaces and 100 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in padding on top and grouting legs of panel . The platform shall be of 40 cm below ground level and 60Cm height above ground level . Rate for Platform shall be included in the quoted rate with the following:-
(a) Incoming
(i) MCCB 04 Pole 26 kA, 315 Amp,415 Volts, fixed thermal & magnetic release (Qty 01 No).
(b) Outgoing:
(i) MCCB 04 Pole 25 KA, 160 Amp, 415 Volts, fixed thermal & magnetic release (Qty - 02 Nos)
(ii) MCCB 04 Pole 25 KA, 100 Amp, 415 Volts, fixed thermal & magnetic release (Qty - 03 Nos)
(iii) Aluminium bus bar suitable size 3 phase, 4 wire 500 Amp,415 V, duly insulated - set of 4
(iv) Digital Volt meter 0-500V with slector switch.
(v) Digital Amp meter 0-400 amp with CT and selector switch.
(vi) Indicating lamp (RYB)LED Type - set of 3 | 3 | Each Job | 1,21,000 ₹3.6 L | 1,25,000 ₹3.8 L | 1,36,000 ₹4.1 L | 1,32,876 ₹4.0 L |
| 6.00 | M&L for replacement of Existing Unserviceable LT feeder pillar box out door type with new supply, installation, commisioning and testing LT feeder pillar box out door type double door and single shutter front open including locking arrangement system made out of MS sheet of 3.15 mm CRCA sheet of size 0.6x0.6x0.3 mtr and double door,canopy,dust proof, bottom cable entry plate and gland for cable size150/120/95/70/50/25/16/10 sqmm 3.5 core suitable MS angle iron 50x50x6 mm with aluminium busbar size 500Amps with Incoming MCCB 315 Amp 4 pole system mounted on hygroscopic insulators bus bar including suitable nut, Bolt and Washer(16 Nos) , & including powder coated paint with and providing necessary foundation/plateform of the feeder pillar legs size 40cm below the ground and 60 cm above the ground complete from groundwith PCC 1:2:4 type B2 including provision of for incomong and outgoing cable gland, thimbling for old / new cables as per site requirement and proper finshing as per existing surface complete all as specified and directed by Engr- in- Charge. Note: Drawing for LT feeder piller box shall be got approved by GE before fabrication.
(a) Incoming :
(i) MCCB 04 Pole 26 KA, 315 Amp, 415 Volts, fixed thermal & magnetic release (Qty - 01 Nos)
(ii) Aluminium bus bar suitable size 3 phase, 4 wire 400 Amp,415 V, duly insulated - set of 4
(iii) Digital Volt meter 0-500V with slector switch.
(iv) Digital Amp meter 0-400 amp with CT and selector switch.
(v) Indicating lamp (RYB)LED Type - set of 3 | 6 | Each Job | 55,000 ₹3.3 L | 51,000 ₹3.1 L | 68,000 ₹4.1 L | 57,895 ₹3.5 L |
| 7.00 | M&L for in replacement of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured heavy duty electric power cable 1100 volts with stranded aluminium conductor of size 400 Sqmm 3.5 core including rate of Lugs/Thimble as per cable size laid in trenches or under road complete all as specified and as directed. (Note: Excavation, cable protection work will be measure & paid separately) | 260 | RM | 2,150 ₹5.6 L | 2,350 ₹6.1 L | 2,577 ₹6.7 L | 2,842 ₹7.4 L |
| 8.00 | All as per serial item No 7.00 here-in- before but of size 185 Sqmm 3.5 core complete all as specified and directed. | 500 | RM | 1,070 ₹5.3 L | 1,180 ₹5.9 L | 1,300 ₹6.5 L | 1,428 ₹7.1 L |
| 9.00 | All as per serial item No 7.00 here-in- before but of size 120 Sqmm 3.5 core complete all as specified and directed. | 500 | RM | 745 ₹3.7 L | 790 ₹4.0 L | 870 ₹4.3 L | 957 ₹4.8 L |
| 10.00 | All as per serial item No 7.00 here-in- before but of size 95 Sqmm 3.5 core complete all as specified and directed. | 500 | RM | 580 ₹2.9 L | 640 ₹3.2 L | 688 ₹3.4 L | 759 ₹3.8 L |
Updated dates
Tender Value
₹46.6 L
EMD Value
₹93,200
Closing Date
22 Apr 2026, 6:00 pmClosed
GE NAMS
GE NAMS Amritsar
SPECIAL REPAIR/ REPLACEMENT OF LT PANELS WITH ALLIED WORKS AT NAMS
2026_MES_757713_1
GE NAMS-98/2025-26
Open Tender
Civil Works
180 days
GE NAMS
CLASS D CATEGORY b(i)
8 documents required · 8 mandatory
₹500
GE NAMS
₹93,200
20 Jun 2026
25 Mar 2026
25 Apr 2026
25 Mar 2026
22 Apr 2026
8 Apr 2026
M&L for in replacement of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured heavy duty electric power cable 1100 volts with stranded aluminium conductor of size 400 Sqmm 3.5 core including rate of Lugs/Thimble as per cable size laid in trenches or under road complete all as specified and as directed. (Note: Excavation, cable protection work will be measure & paid separately)
All as per serial item No 7.00 here-in- before but of size 185 Sqmm 3.5 core complete all as specified and directed.
All as per serial item No 7.00 here-in- before but of size 120 Sqmm 3.5 core complete all as specified and directed.
All as per serial item No 7.00 here-in- before but of size 95 Sqmm 3.5 core complete all as specified and directed.
All as per serial item No 7.00 here-in- before but of size 35 Sqmm 3.5 core complete all as specified and directed.
All as per serial item No 7.00 here-in- before but of size 25 Sqmm 4 core complete all as specified and directed..
Supply, laying & fixing double wall corrugated (DWC) pipes made of high density polythyline (HDPE) with all accessories i.e. all type of joints, Sockets, Elbows, bends and End caps as size of DWC pipe is 50mm outer dia and 38 mm inner dia complete all as specified and directed by Engr in Charge.
All as per srl item No 13.00 here-in-before but of size 90 mm outer dia and 76mm inner dia complete all as specified and directed.
All as per srl item No 13.00 here-in-before but of size 110 mm outer dia and 93mm inner dia complete all as specified and directed.
Excavation in trenches n .exc 1.5 mtr wide and not exec 1.5 mtr in depth for foundation etc or for laying pipe lines and cables and getting out as in looses/soft soil complete all as specified and directed.
Returning filling in including spreading leveling, watering and well ramming in layer not exe. 25 cm in soft/ loose soil, complete all as specified and directed.
Removing excavated material to a distance not exc 50m and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and directed.
M&L in replacement for earthing complete with galvanized iron or steel plate electrode 600 mm x 600 mm x 6.00 mm thick buried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected to galvanized iron strip 25 x 4 mm dia as earthing lead by means of GI bolts, nuts, check nuts and washers, earth strip protect0ed by galvanized steel pipe 40 mm bore (light grade) connected to machinery/ equipment all as shown in electrical plate No. 3 of SSR-2010 Part I and including necessary excavation and earth work in any type of soil, 20mm bore light grade GI pipe for watering, funnel, wire mesh, PCC (1:3:6) type C-1 chamber, MS cover of thickness 5mm openable type and having suitable locking arrangement and MS frame of suitable size made of angle iron 50 x 50 x 60 mm, complete all as specified. Note: (i) The unit rate includes earth lead and protection pipe up to maximum 7.5 metre from earth plate to earth point/test point. (ii) Earth pit shall be constructed minimum 0.5 metre away from earth.
Supply & fixing earth strip continuity conductor on main earthing lead fixed toPanel/pole or buried in ground or at any other situation for loop earthing extra as required (beyond 7.5 M) of GI Strip 25x4 mm complete all as specified and directed.
M&L for Boring of holes under road, pavement, hard standing by trenchless ultra sound technology/mannual all as per site requirment complete all as specified & directed.
Please Enable Macros to View BoQ information
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.67 MB
98T.pdf
Tender Documents • 1.68 MB
BOQ_848734.xls
BOQ • 10.76 MB
Download all tender documents and submit your bid