Balance work for construction of Commercial Tax Office Complex at Solina Srinagar

Amount

Clearance of site by way of removing garbage humps extracting of bushes by mechanical/ manual means including removal of same from site to out side municipal limits with roots making site workable for laying of layout for proposed building.

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. ( All kinds of soil).

Providing and laying of soling stone size on level (hand packed ) watering ramming complete below Foundation& rooms including carriage.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level 1:4:8 (1 cement : 4coarse sand : 8 graded stone aggregate 40 mm nominal size) PCC below Foundation& rooms-Mudmat including carriage.

Boring, providing and installing 600 mm dia bored cast in situ reinforced cement concrete pile of specified diameter and length below the pile cap in M 30 cement concrete, to carry a safe working load not less than specified excluding the cost of steel reinforcement but including the cost of concrete, boring with casing and /or bentonite solution and temporary casing of appropriate length for setting out and removal of the same and the length of the pile to be embeded in the pile cap etc. all complete including removal of excavated with all lifts and leads (length of pile for payment shall be measured from top of shoe to the bottom of pile cap) Length up to 20m .

Chipping of RCC pile heads by way of chiseling/through cutter etc. upto cut off level by manually means- M30 Piles upto 0.6m including disposal lead upto 200 Mtrs.

Filling in plinth etc in layers not exceeding 20 cm in depth consolidating each layer by rammng, watering complete job a) Available earth filling in trenches.

b)Sand filling under flooring in rooms.

c)GSB filling under flooring in rooms.

Conducting of Vertical load testing piles in accordance with IS- 2911( PART IV) including installation of loading plateform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specifications & the direction of engineer in charge Working piles Single pile above 50 tonne and upto 100 tonne safe capacity

Providing and laying in position specified grades of reinforced cement concrete M-25 grade in beams, slabs, walls(any thickness) including attached pillasters, buttresses, plinth and string courses, filets, columns, , stairs,pillars, piers, abutments, posts and struts etc. using 20mm thick crushed stone agg. Excluding the cost of centring, shuttering, finishing and reinforcement. All work upto roof level.

All work upto plinth level.

All work above plinth level.

Reinforcement for RCC works including straightening, cutting, bending, binding & placing in position all complete. HYSD reinforcement of grade Fe-500D steel bars at all levels.

Centering and shuttering including strutting, propping etc. and removal of form work for:-

Pile foundation, pile caps etc.

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Floor Beams

Columns, pillers, piers, Abuments posts and struts.

Suspended floors, roofs, landings balconies and Access platform

Stair (Slopping/steps/sides).

Edges of slab and breaks in floors and walls (Under 20 cm wide)

Structural steel work welded in built up section for trusses and framed work including cutting hoisting, fixing in position anchor bolts and applying a primer coat of approved steel primer. @ 45 Kg/Sqm

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in :(Cement mortar 1 :6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand) Extra for half Brick masonry in superstructure above plinth level upto floor V level.Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry.

15mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement: 4 fine sand) (including cost of all material, leads, lifts and carriages etc upto site of work complete).

12 mm thick cement plaster on ceilings, soffits etc. in (1 cement: 4 fine sand mix). Upto floor V level complete in all respects (including cost of all material, leads, lifts and carriages etc. upto site of work complete).

Providing and fixing of U-PVC sliding/casement/fix doors in whote colour,frame 60mm thick (min) x 45mm (min) with 1.5 mm GI reinforcement sash 39mm (min) 58mm (min) with 1.25mm GI U section reinforcement with rubber gasket of grey / black colour 10 years warranty against weathering of profile with complete hardware fittings fixed with 12mm thick laminated board panels as per design and with 5mm toughened glass and fiber jalli option if pre- febricated on german fabrication system( mosquito sash 18mm(min) x 43mm(min)(with welled cornes) complete at site including all fixtures

Providing & fixing U-PVC system in walls in white colour,frame 60mm (min)x45 mm (min) with 1.5 mm GI reinforcement,sash 39 mm (min)x58 mm(min) with 1.25 mm GI- U section reinforcement with rubber gasket of grey/black colour, 10 years warranty against weathering of profile with complete hard ware fittings and with 5mm clear toughned glass with 12mm thick laminated board panels as per design wherever required pre-fabricated on German Fabrication system(Mosquito sash 18 mm(min)x43 mm(min) (with welded corners ) complete at site.(For partition Walls )

Providing and fixing factory made uPVC white colour partation walls comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. sealant shall be paid separately) Note: dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Dimensions of sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension

roviding and supplying Armstrong ‘Optra Acoustical Wall Paneling’ with square edges made of fibre glass substrate 25mm thick and wrapped on the front side with an acoustically transparent and classified for Fire reaction Class B-s1, d1 as per EN13501, fabric with an option of colors – Ivory, Autumn Orange, Pista Green, Straw Gold, Rustic Green, Burgundy, Rust, Peacock Blue, Ash Grey, Mocha as per the choice of the Architect of size 600X1200 mm providing a minimum sound absorption level of 0.90 NRC to be affixed to wall using Wall panel impalers supplied by M/s Armstrong Industries India Pvt. Ltd and construction adhesives as per the instructions laid down by the manufacturer. INSTALLATION:4nos. Armstrong wall panel Impalers of shall be fixed to the wall surface using self tapping screws. Silica based construction adhesive to be dabbed on to the projecting elements (spikes) of the impalers. Armstrong Optra wall panels shall be pierced through the spikes of the impalers ensuring the line and level of the panels are maintained.

Providing and fixing of 24 mm thick rubber wood board for wall penelling designed in ornamental pannals shape square / rectangular. Including cost of necessary adhesive ,budloo wood backing and cost of nails etc specification and design approved by engineer in charge/consultants.complete job.

Proving and fixing of wall paper on walls . Including cost of necessary adhesive specification and design approved by engineer incharge/consultants/client.complete job

Providing and applying cement based wall putty of required thickness over plastered surface to prepare the surface even and smooth complete in specified areas as per specified patter. (Birla make) (including cost of all material, leads, lifts and carriages etc upto site of work complete).2mm thick.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):First class deodar wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured)

Providing and fixing glazed shutters for doors, windows and clerestory windows using 5mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. (Note: -Butt hinges and necessary screws shall be paid separately)(First Class deodar wood).35mm thick.

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :First class deodar wood 35mm thick.

Providing and fixing 5mm thick panels of plain glass for fixed glazing panels/ shutters (only panel area to be measured) including cost of teak wood beadings of required size complete.(Fixed)

Providing and fixing hardware fittings of approved brand and of required type as approved by Engineer incharge. complete as per the specifications (Brass)

Modular door lock ss finish handle 10" with duaal locking system inside & outside (godrej)

Tower bolts 100x10 mm(Brass)

Handles 125 mm(Brass)

EYE-Hooks 150mm(Brass)

Tower bolts 150x10 mm(Brass)

Brass butt hinges100x85x5.5 mm (heavy type)

Applying priming coat With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)(Brass)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/ m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³. The frame will have a provision of G.I. Anchor fastners 14 nos (5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge. (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for separately).

Providing and fixing glazing in fire resistant door shutters, fixed panels& partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (EI20). The manufacturers have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing of DORMA Make or equivalent SS Ball Bearing Hinges of 100 x 89 x 3mm SUS 304 Grade complete with SS Screws ( 4 Nos per panel )

Providing and fixing of DORMA TS 73V door closers tested in accordance with BS: 476 Part – 22: 1987 with manufacturers warranty and tested with complete assembly offerred by manufacturer

Providing and fixing of DORMA make Lock 952 F alongwith 80mm Cylinder and necessary screws as required.

Providing and fixing of Dorma make Tower Bolt 600 mm long

Providing and fixing ( gang saw cut mirror polished (flamed , pre-moulded and pre-polished), machine cut for flooring, steps ,risers of stairs etc.( flamed instaircase) of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding (of edges wherever required ) and polishing to edge to give high gloss finish etc. complete at all levels. Granite of Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent,and shape 18mm thick. and slab area over 0.50 sq m. (Note: The Granite stone slab shall be cut to required size and laid to the required pattern including rounding, chamfering, & nosing of the edges as directed. Actual area of slab, as laid shall be measured) Sample to be approved by Engineer-in-charge. (including cost of all material, leads, lifts and carriages etc. upto site of work complete

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. Size of tile 600x600 mm

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete.In colour such as White, Ivory, Grey, Fume Red Brown

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Kota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) :

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc.,by applying cemnet slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement@ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement compound @ 0.126 kg/sqm. This layer will be allowed t air cure for 4 hours followed with water curing of 48 hours. The rate includes preparation of surface, treatment and sealingof all joints ,ciorners, juntions of pipes and masonry with polymer mixed slurry.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.(Crushed)

Providing/fixing of Khatambandi Ceiling of ist Class Budloo Wood of specified pattern in ceilings etc. including, necessary frame work work of 50 mm x 75mm size ,and 12mm thick ply board frame in lining of Budloo wood underneath and other incidentals including cornice of size 75mmx75mm of Budloo Wood all complete in all respectes.as per the directions of Consultant/as per the drawings enclosed (chaar gul).

French spirit polishing, Two or more coats on new works including a coat of wood filler.

Providing, fixing and applying Plaster of Paris (POP) false ceiling consisting of frame work made with 50mm sq M.S. tubes of 18 G thickness as main runner at 600 mm c/c both ways, suspended/ supported with M.S. flats 25x4 mm from existing R.C.C. slab, finished smooth to line and level including necessary supports, scaffolding etc. as required and also including applying a coat of red oxide zinc chromate primer over the M.S. frame work and suspenders complete. Including providing and fixing expanded metal of size 5.25 mm x 1.25 mm thickness welded to main runners and applying POP (calcium sulphate semi hydrate variety) to the expanded metal of thickness not less than 10 mm.

Providing and fixing mineral fibre false ceiling tiles at all heights ofsize 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking TGrid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size 24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all Tsections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-incharge.With 20 mm thick bevelled tegular mineral fibre false ceiling tile (NRC 0.7)

Providing and fixing planned eaves boarding (300mm x 40mm )( nominal size) second class dewdare wood fixed with screws etc, including all carraiges .All job completed

Providing and fixing 20mm thick wooden planks ceiling/ soffit(frame work for base to be paid for separately) with M.S. screws 2nd class kail wood

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position using Budloo / Fir wood including cost of nails,scaffolding etc complete job (making grid of 2'-0"c/c ,2''x3'' section)

Providing corrugated Green colour coated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required, 0.50 mm thick with zinc coating not less than 275 gram/m2 complete. ( TATA / JINDAL / BHUSHAN )or equivelent.

Providing and fixing thermal insulation of ceiling (under deck insulation) with specified glass wool conforming to IS: 8183, 50mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3mm) @ 60cm c/c and wire mesh of 12.5mm x 24g wire for top most ceiling of building. With resin bonded fiber glass wool with density 24 kg/cums

Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete, 0.50 mm thick with zinc coating not less than 275 gram/m2. ( TATA / JINDAL / BHUSHAN).

Providing valleys of 90cm wide overall in plain G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 1.00 mm thick with zinc coating not less than 275 gram/m2

Providing and fixing Antiskid Vitrified pavement tiles 300x300x10mm thick laid on 20mm thick cement mortar 1:4 1 cement: 4 coarse sand] and jointing with Tile Grout as per approved colour complete as directed by Engineer-in-charge.

Finishing walls with exterior ultima Allura Torino paint of required shade texture rough washability, anti fungal, @ 0.4 kgs / sqm in two coats Including primer coat complete in all respects.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing & fixing of stainless steel nevel post (Ornamental ) including top ball of AISI 304 grade of required height duley anchored to floor with dash fasteners . Height of the nevel post shall not be less than 1050 mm above the finished skirting level all complete as per architectural drawings (including cost of all material, leads, lifts and carriages etc upto site of work complete).Complete as per the directions of Engineer incharge.

Providing and applying ornamental molded cementing plaster vertical post with mix of 1 cement and 1 fine sand(1 :1 mix ) including material scuffolding shuttering etc complete job as per architectural drawing/ and approved by consultant / client .

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Pointing on brick masonry in lime Surkhi (I Lime: 2 Surkhi ) including finishing the joints with lime surkhi pigments to give a local heritage touch as per the directions of Engineer incharge upto desired height complete in all respects. (Including all lead, lift, labour, materials, tools, plants complete as per specification and as directed by Engineer in Charge.

Providing and fixing dagi dewari as per local architectural heritage 100mm x 40mm wooden planks of ist class kailwood wood fixed horizontally, vertically, inclined with necessary screws,paint and other items ( Ist class kail wood)

Providing and fixing wood work (ornamental type) horizontal /vertical members for exterior face of window work(ARCHITRAVE) as per the local heritage /architectural features and as per the directions of consultant including cost of all material ,leads lifts and carriages upto site of work complete) ist class kail wood as per the directions of the consultant.

Providing and fixing 2nd class Deodar wood 18 mm thick Wooden planking, tongued and grooved in flooring including fixing with iron screws cut to required shape and laid to required pattern including chamfering of the edges as direted by engineer-in- charge sample to be approved by engineer incharge ( including cost of all material, leads,lifts and carriage etc upto site of work

Providing and fixing Flotex carpet sheet/roll 4.3mm thick cut pile floor covering, pile material 100% nylon 6.6 having resilient water proof backing material and total weight of carpet should be 1.8 Kg/sqm and anti sound absortion of 0.10 of Consolidated Carpet make or approved equivalent make and shade in flooring and skirting in approved pattern on a smooth top and damp proof base using adhesive of approved quality and manufacture including rolling with light wooden roller and the cost of levelling the surface with self levelling adhessive etc. all complete as per manufacturer's specification.

Providing and fixing devri stone clading 25 mm thick with exposed face fine dressed with rough backing on wall lining etc. upto 10 meter ht back filled with a grout of 12 mm thick cement sand mortar in 1:3 (fine cheiseled)including pointing in white cement 1:2 with admixture of pigment matching to stone

Providing and fixing ornamental pendents of 250mm x 250mm x 450 mm each sides as corners of roof as per the local heritage /architectural features and as per the directions of consultant including cost of all material ,leads lifts and carriages upto site of work complete) ist class dewdar wood as per the directions of the consultant/as per drawing enclosed

Provding & fixing of spider , glass 12mm thick thoughned of Saint Gobain make , using ozone make spider viz , four way spider ( OSP -A4) , 2 way ( OSP-A2) spider , single leg spider ( OSPA-22) , fin plates ( OSP-FP-300) of 300 mm also using 8mm +1.52 +8mm fines at 90 degree to hold glass at joints . This will include the main glass door with all necessary fittings , hinges , handles , Locks , hydrolic hinges complete job. Also the structure is designed to with stand the wind pressure of 85 miles per hour . Hilti make chemival , fastners will be used to fasten spider , with RCC , all the facade will be as per Drawings and upto satisfication of Engineer / Architect , inclusie of scaffolding , loading , unloading .

Providing and fixing ACP sheets 4 mm thick panels including cost of washers/screws etc complete job.

Supply and installation signage plates for rooms.meeting halls etc of size 120mm x120mm x1.5mm in ss304 matt finish having letters engrave in the ss plate in black vinyl steam pressed to get a clean finish and having font size of name atleast 30mm fixed on the wall or door surface with high quality adhesive tape of 3M or equivalent complete to thesatisfaction of engineer in charge

Supply and installation signage plates for FIRE EXIT/ LIFT SIGNAGE of size 120mm x120mm x1.5mm in ss304 matt finish having letters engrave in the ss plate in black vinyl steam pressed to get a clean finish and having font size of name atleast 40mm fixed on the wall or door surface with high quality adhesive tape of 3M or equivalent complete to thesatisfaction of engineer in charge.

Supply & fixing stainless steel (SS) letters made with SS-304 grade 20 gauge sheet of as per the approved size & shade including fixing on HPL sheet in required height line & level including s/o all T&P etc. required for proper completion of work. Before making the letters the font & size will be got approved.(100 X 300MM SIZE)

Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters (including accessories) including stacking of articles within lead of 100m

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 meters lead.

Demolishing Brick / Stone Masonry in cement mortar up to floor-2, including stacking of serviceable material stacking /disposal lead up to 100m

Demolishing of RCC work by using hydrolic jack hammers up to floor 2 level, thickness over 150 mm including stacking of steel bars serviceable material and disposal of unserviceable material , disposal lead up to 50m

Dismantling tiled roofing consisting of battens , boarding’s , including stacking of serviceable material and disposing of unserviceable material ,stacking disposal lead of 100m

Demolishing cement concrete manually/by mechanical means including disposal of material within 100 meters lead as per direction of Engineer-incharge: 1:3:6 or richer mix.

Dismantling dressed stone work manually/ mechanical means ashlar face stone , marble work or precast concrete work including stacking of serviceable material and disposal of unserviceable material with in 50 m lead

Taking out wood/ steel frames ( chowkats) including stacking of material within a LEAD of 100

Dismantling and Dismembering of Stair RAILING , including stacking of material with LEAD of 100m

Dismembering / dismantling of sanitary/plumbing fixtures/fittings including stacking of servicable / and disposal of unserviceable material with in lead of 100 Mtrs.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets,40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing Under Counter wash basin,with 32 mm Waste Coupling and other allied accessories including cutting and making good the walls wherever required:-White Vitreous China Under Counter Wash basin.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required :510x1040 mm bowl depth 225 mm.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 1500x450 mm

Providing and fixing toilet paper holder with Flap made out of C.P Brass

Providing and fixing C.P Brass Soap Dish.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing CP brass towel rail complete with CP brackets fixed to wooden cleats with CP brass screws .

Providing and fixing CP Short Body Bibcock with Valve Flange

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931(15 mm nominal bore)

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia

Providing & fixing of 100mm dia C.P. grating (anti cockroach grathing) of standarad quality. complete job.

Providing and fixing soil, waste and vent pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing.

160 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

75 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

Providing and Fixing of Floor Traps 110 mm with double chrome plated Cover one Grated and one closed and all other fittings required.Makes:- Astral/SFMC/Finolex

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge. Concealed work, including cutting chases and making good the walls etc.

1620 (20 mm OD) pipe

2025 (25 mm OD) pipe

2532 (32 mm OD) pipe

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge. Internal work (Exposed on wall)

2025 (25 mm OD) pipe

2532 (32 mm OD) pipe

3240 (40 mm OD) pipe

4050 (50 mm OD) pipe

5065 (65 mm OD) pipe

7590 (90 mm OD) pipe

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge. External work

5065 (65 mm OD ) pipe

Providing and Fixing of Thermal Insulation for Hot Water Lines made out of Flexible Elastomeric Foam of Closed Cells Structure Having a Thermal Conductivity of 0.038 W/m.K at 200 Deg C water Vapour Permeability of Cu.m 5000 as Required including accessories i.e Adhesives/Tape on all Joints as per the satisfaction of the Engineers Incharge.

1620 (20 mm OD) pipe

2025 (25 mm OD) pipe

2532 (32 mm OD) pipe

3240 (40 mm OD) pipe

4050 (50 mm OD) pipe

5065 (65 mm OD) pipe

7590 (90 mm OD) pipe

Providing and fixing unplasticised PVC connection pipe with brass unions: 45 cm length,15mm nominal bore

Cutting holes upto 30x30 cm in walls including making good the same with common burnt clay F.P.S.(non modular) bricks

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms,lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.

Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of P.V.C pipes including bed concrete as per standard design :

160 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

Providing and fixing square- mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design. 100 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing & fixing full way lever operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 16 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc.

90 mm Diameter

65 mm Diameter

50 mm Diameter

40 mm Diameter

32 mm Diameter

25 mm Diameter

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing & fixing of electric geyser with ABS body 50 litre capacity (of approved make) incl. all fittings complete job.

Providing & fixing of electric geyser with ABS body 25 litre capacity (of approved make) incl. all fittings complete job.

Supply,Installation,Testing and Commissioning of Open Well Submersible Pump(1 W+1 S ) with a Discharge of 6.0 Cu.m/hr @Head of 45 Meters Complete with all accessories including header Pipes, allied materials and automatic Control Panel.

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-incharge.

62mm thick cement concrete flooring with concrete hardener topping under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 liter per 50kg of cement or as per manufacturer’s specifications, including cost of cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete.

Providing and fixing 15 mm nominal bore C.P. brass health faucet for European W.C

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms

Providing and fixing 18mm stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-Charge and finished smooth.Granite Stone of approved shade.

Providing and fixing Glass strips 40mm wide and 4mm thick in joints of terrazzo/ cement concrete floors.

M.N.Enterprises

N S Associates PVt Ltd

S K Integrated Consultants