REPAIRS TO KITCHEN TOILETS AND PLASTERING IN OTM ACCN AND INTERNAL WIRING ELECTRICAL FITTING FIXTURES IN THE AOR OF AGE B R MEG AND REPAIRS TO FLOOR PLASTER CEILING JOINERY AND CERTAIN MISC WORKS IN PAO MEG UNDER GE BNG

Amount

Demolition of cement concrete and paving not exc 15 cm thick (below or above ground level) complete all as specified and as directed.

Demolition of brick work /stone masonry / PCC block masonry built in cement mortar of any description all as specified and directed.

Dismantling of floor, hearth or wall tilling incl cement mortar bedding (but not backing) and removing rubbish off from premises.

Taking down cement plaster of any description hacking for key or raking out joint on old brick work/stone/concrete surface

Supply & laying 20 mm outer dia CPVC pipes SDR 11 (Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings and specials complete all as specified.

S&F 20mm dia GI tubing medium grade and fixed complete to walls and ceiling or laid in floors complete all as specified and directed

S&F 25mm dia GI tubing medium grade and fixed complete to walls and ceiling or laid in floors complete all as specified and directed

Dismantling water tanks and removing to store (exc 250 and not exc 500 ltr capacity) / removing off site.

Dismantling water tanks and removing to store (exc500 and not exc 1000 ltr capacity) / removing off site.

M & L rotational moulded polythene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I capacity of tank 500 ltrs complete all as specified and directed

All as per item No 10 above but except tanks

M & L rotational moulded polythene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I capacity of tank 1000 ltrs complete all as specified and directed

All as per item No 12 above but except tanks

S & F in repairs 20 mm dia bore ball float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and as directed [Minimum weight for 20 mm – 210 gms] .

S & F in repairs 20 mm gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and including taking down old gate valve all as specified and as directed.

S & F in repairs 25 mm gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and including taking down old gate valve all as specified and as directed.

S&F in repairs Brass CP wall mixer for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed (Cat No-PIS-75H of Neptune series of Prayag or equivalent make as specified in CA)

S & F in repairs 15 mm Centre hole Basin mixture W/o Pop Up all as specified and as directed.(Cat No PIS-50 H Neptune series of Prayag or equivalent make as specified in CA)

S & F in repairs 15 mm pillar taps swan neck type, chromium plated cast copper alloy fancy type complete all as specified and as directed.(Cat No PIS-14H Neptune series of Prayag or equivalent make as specified in CA)

S&F in repairs 100mm (4") overhead shower ABS with brass Arm (225mm) & flange including fixing to steel pipe or union complete all as specified and as directed. (Cat No BS-73 Neptune series of Prayag or equivalent make as specified in CA)

S & F in repairs 15mm angle cock CP cast copper alloy screwed down high pressure with capstan head handle screwed both ends or for unions etc . (Cat No PIS-10H Neptune series of Prayag or equivalent make as specified in CA)

S & F Bib Cock 2 way double handle with CP flange as fixed in repair all as specified and as directed. (Cat No-PIS-12H Neptune series of Prayag or equivalent make as specified in CA)

S & F chromium plated long body bib tap 15mm dia with CP flange as fixed in repair all as specified and as directed. (Cat No-PIS-08H Neptune series of Prayag or equivalent make as specified in CA)

S & F chromium plated bib tap 15mm dia with CP flange as fixed in repair all as specified and as directed. (Cat No-PIS-06H Neptune series of Prayag or equivalent make as specified in CA)

S&F in repairs Health faucet, brass body with 1mtr SS braided tube & wall hook complete all as specified and as directed (Cat No-BEA-41/BEA-85 of Prayag or equivalent make as specified in CA)

S & F in repairs Towel rail stainless steel glossy finish complete all as specified and as directed. (Cat No-BA10S of prayag or equivalent make as specified in CA)

S&F in repairs Towel rack Brass glossy finish complete all as specified and directed (Cat No BA-03 of Prayag or equivalent make as specified in CA)

S&F in repairs Towel ring Brass glossy finish complete all as specified and directed (Cat No BA-02 of Prayag or equivalent make as specified in CA)

S&F in repairs Soap dish chromium plated brass all as per Cat Part No BA-45 of Prayag or equivlaent makes fixed in wall as per manufacturers instruction.

S & F in repairs Mirror 600x450 x 5-6mm thick with frame cat No BLM-01F of PRAYAG or equivalent make complete all as specified and directed

S&F in repairs PVC Mirror cabinet of size 400x500 mm (Cat No 554 of Prayag or equivalent make) complete all as specified and as directed.

S&F in repairs Unbreakable (Square) wall mounted shelf 500mm (Cat No BEA-47A of Prayag or equivalent make as specified in CA) complete all as specified and directed

S&F in repairs Unbreakable corner shelf (3Pcs set i.e 8"-1, 10"-1 & 12"-1) (Cat No BEA-44A of Prayag or equivalent make as specified in CA) complete all as specified and directed

S&F in repairs peg set of six (Cat No BEA 30 of Prayag or equivalent make of CA) fixed in wall as per manufacturers instruction

S&F in repairs Toilet paper holder (Cat No BA-88 of Prayag or equivalent make of CA) fixed in wall as per manufacturers instructions

S & F in repair PVC connection (Suitable for Cold Water Supply) 15 mm size with PTMT nuts of length 450 mm, all as specified and as directed.

S & F in repair PVC connection (Suitable for HOT Water Supply) 15 mm size with PTMT nuts of length 450 mm, all as specified and as directed.

M&L 32 mm dia waste fittings,brass,chromium plated for sinks,basins,etc with long screwed shanks and flynuts,flange end fixed in repair complete all as specified and as directed

S & F in repair 75mm dia PVC(SWR) Multi floor trap,plain with grating including jointing with slvent cement all as specified and as directed.

S & F in repair grating doom 100 mm dia of PTMT complete all as specified and as directed

S & F kitchen sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in mortar on to dwarf wall or including fixing cantilever brackets and connecting union pipes overall size 915 x 460mm bowl size 410 x 330 x 160mm complete in repairs including Dismantling of old sink .

S&F of kitchen sink made of stainless steel 1mm thick kitchen with plugs, washers and wastes: including bedding in cement mortar to dwarf wall or including fixing cantilever brackets or fixing in granite slab and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete in repairs including Dismantling of old sink

S&F in repairs stainless steel plate rack of 0.63mm thick sheet, size 800mm x 600mm complete all as specified and as directed

S & F vitreous china wash basin white flat back size 550x400mm excl chain and plug and porcelain stopper but incl CI bracket. waste fittings, brass chromium plated for glazed ware sinks, basins etc with long screwed shanks and flynuts, flange end bedded in red leead cement and other end fixed, PVC waste pipe 75 cm long complete all as specified and directed fixed in repairs

S & F vitreous china wash down water closet pan (Pedestal Pan) including fixing bolts, flush pipe anti syphonage pipe, plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device etc complete of cera model cat pt no. 2008 incl plastic EWC seat cover, coloured closed pattern with flat bottom and cover of cera model cat pt 2308 and mild steel chromium plated or aluminised hinging device as in repairs complete all as specified and directed

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including PVC SWR P trap connecting to flush pipe and to anti syphonage pipe, etc. complete including making good to floor, fixed in repairs complete all as specified and directed.

PVC valveless, syphonic action type, flushing cistern, Duo Flush cistern 10ltr capacity,low level, white, with inlet, ball valve, float and handle including brackets, connections to pipes and fixing of chain and pull, or lever, fixed in repairs complete all as specified and directed. (Cat No-502 of Prayag or equivalent in any approved make as in CA)

M & L cement concrete type B0 1:2:4 (12.5 mm graded stone agg) 25mm thick as in levelling concrete finished even and fair complete all as specified and directed.

M&L Screed bed or bedding layer of mortar 15mm thick in CM 1:6 for laying floor finishes complete all as specified and directed

M&L Rendering 10mm thick in CM (1:3) on Brick work or stone masonry surface as backing coat of tiles complete all as specified and directed

M&L Non Skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed

M & L Glazed coloured ceramic tiles in vertical surfaces 300x450x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed

M&L for vitrified ceramic light coloured tiles 8-10mm thick (square/rectangular)polished, area of each tiles not exc 0.36sqm in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed

M&L for vitrified ceramic light coloured tiles 8-10mm thick (square/rectangular)polished, area of each tiles not exc 0.36sqm in vertical surfaces such as skirtind/dados, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed

M&L Pre-polished Machine cut Granite stone slab 25mm thick with edge rounded one side laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Taking down chowkat (without taking off shutter from the frame) not exc 1.5 sqm each including making good the disturbed surface in PCC 1:2:4 type B0 or CM 1:3 all as specified and directed

All as per Item No 56 above, but exc 1.50 sqm and not exc 4.00 sqm each

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each all as specified and as directed

S & F in repairs 18mm thick, PVC sheet one side prelaminated of approved texture ("Celuca Ply of Rajshree make or equivalent as approved by GE) as in Kitchen cabinet (with shelves and partitions) including necessary fittings & fixtures as per manufacturer's instructions complete all as specified and directed.

S&F stainless steel kitchen basket in various type of basket, plain basket height 4" Thali basket 8" height Cup saucer 4" heigt and perforated cutlury basket 4" height all as specified and directed. (Make : Hettich / Godrej or techno commerically equivanlent)

S&F Stainless steel channel for basket sizes 600mm long and 46mm wide all as specified and directed (Make : Hettich/Godrej)

S&F stainless steel handle for basket size 6" all as specified and directed

S&F stainless steel Auto closing concealed hinges 9.5 cranks for half overlay doors with opening angle 95* (14-32mm) with integrated overlay adjustment +_ 2.50mm & depth adjustment 4mm complete all as specified. Make : Godrej / Hettich.

S & F in repairs 18/19MM THICK Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, alround 6mm thick teak wood fillets fixed in kitchen Cabinet or cupboards all as specified.

M&L for Plain fillets square, rectangular or triangular in section clean sawn, secured with nails or brads of second class hard wood fixed to cupboard shutter Not Exc 3 sqcm cross section area all as specified and directed.

S&F Solid PVC door frame (Single rebated) of size 60 mm x 30 mm made out of solid foam with homogenious fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100x8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) complete all as specified and directed

M & L for factory made solid PVC moulded door shutter , 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face & 2mm plain colour PVC sheet on back face supplying and fixing in frame at site as per specification & drawing with wood free EPS .

S&F Flush door shutters 35mm thick, factory made as per IS:2202 (Part-I 1999) solid core construction, with block board core with decorative face veneer both faces with lipping/frame to match as per drawing fixed to chowkhats all as speified and directed

S&F framed work as in doors or gates of angle or other sections with gusset plates, rails braces, etc complete drilled for fixing of steel sheeting or other covering, doors etc, to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings(exclusive of steel sheeting or other covering, running rails and guides) and hanging ; also fastening and fixing complete including painted with one shop coat of zinc chromate primer paint (including preparation of surface) at contractors workshop / factory before fabrication complete all as specied and directed

M & L applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces over 10 cm width or girth including preparation of new steel surfaces

S & F Butt hinges stainless steel 100mm long and fixed to door frame and shutter duly welded/screwed complete all as specified and as directed

S & F Butt hinges medium weight, cold rolled mild steel 100mm long and fixed to door frame and shutter duly welded/screwed complete all as specified and as directed

S&F Aluminium anodised tower bolt 150mm long of extruded section etc complete all as specified and as directed

S&F Aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed

S&F 150 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed

S&F Mild steel barrel tower bolt 200 mm long of extruded section etc complete all as specified and as directed

S&F 150 mm long Mild steel pressed handle, oval type stove enamelled black complete all as specified and as directed

S&F Mild steel sliding door bolt 300 mm long plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6bolts and nuts, four on bolt plate and two one staple plate and fixed complete all as specified and as directed

S&F aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy etc complete all as specified and as directed

S & F 150 mm floor door stopper of aluminium alloy powder coated, with hard down steel spring all as specified and as directed.

S&F in repair mild steel 300mm, ordinary rat tail rod pattern springs,including roller and roller plate complete

S&F Anodised aluminum powder coated (of any shade/colour as approved by GE ) ventilators with adjustable 4mm thick figured glass louvers, fixed in qtr portion, without sash bars, aluminum section weighing not less than 0.55 kg/m including necessary jointing cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws, including stainless steel wire cloth 0.36 nominal dia of wire and average width of aperture 1.18mm including complete etc all as specified and directed by the Engineer-in-charge (Size of Ventilators = 600 x 900 mm)

S&F Anodised Aluminum Powder coated three track sliding aluminum window including Frame and shutters consisitng of 2x glazed shutter (thickness of glass not less than 5mm) & 1xGauged shutter(stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperature 1.40mm), Aluminum sections weighing n.less than 0.55 kg/m including necessary jointing cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws, anodised aluminum fittings such as peg stays, self closing clips, handles etc all as specified and directed

Hacking out old broken glass (any thickness, size, quality or description) from wooden surface concrete or brick surrounds. Glazed with putty or fixed with beads all as specified.

S & F Sheet glass 4mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane and all as specified.

S & F in repairs stainless steel wire cloth 0.36mm nominal dia and average width of aperture 1.40mm and fixed with tinned tack or galvanized wire staple all as directed fixed.

S & F GI grid suspended false ceiling grid system of size 600 x 600mm with main runner 29 x 24.7 x 0.8mm cross tee 29 x 24.7 x 0.8mm and wall angle 22.2 x 22.2 x 0.65mm. Ceiling suspended with 3mm dia GI wire hanger fixed with steel dash fastner, butter fly clips, hold down clips etc (Main runner, cross tee & wall angle of MS galvanised with PPPCGS) including 4mm thick HPSC self textured design pre primered non asbestos fibre cement building board fixed to false ceiling complete including taking down old celing of any description .

M&L Precast cement concrete block masonry Type C1 1:3:6 (using 20mm graded stone aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L providing cement concrete type B0 1:2:4 (12.5mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges in chajjas etc complete all as specified and directed.

M&L for rendering 15 mm thick on fairfaces of brick work or concrete / stone surface in cement mortar 1:6 finished plastered surface even and smooth without using extra cement

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:4 with WPC, finished plastered surface even and smooth without using extra cement Note :- WPC will be measured and paid separately

Supply only liquid water proofing compound

M&L for rendering 5 mm thick on ceiling /RCC surfaces in cement mortar 1:3, finished plastered surface even and smooth without using extra cement

M&L Cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) 100mm thick as in subbase

M&L for cement concrete type C-1, 1:3:6 ( using 20 mm graded crushed stone aggregate ) 75mm thick as in plinth protection, laid in alternate bays (not exceeding 2 Sqm each) finished the concrete surface even and smooth at top without using extra cement and providing joints throughout the thickness of plinth protection, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight all as specified and directed

M&L chequerred cement concrete tiles 300x300x25mm thick set and jointed and pointed in neat cement slurry with grey cement and pigments to match the colour of tiles over and including 20mm thick screed bed in CM (1:4) complete all as specified and directed by Engineer-in-Charge

M&L Preparation of newly plastered surfaces and applying two coat of oil bound distemper over a coat of alkali resistent primer over two coats of wall care putty complete all as specified and directed

M & L preparation of newly plastered surface of wall and applying two coats of cement base paint complete all as specified and as directed.

M & L for preparing newly plastered ceiling surfaces and applying three coat of white wash complete all as specified & as directed.

M&L for providing and laying water proofing treatment to sunken portion of WCs, bathroom and kitchen etc by applying cement slurry mixed with two component Elastomeric Acrylic based polymer modified cementitious composite compound coating of make as approved in TI 5/2003 including demolition and removal the same from site of existing treatment of any type. The following procedures to be adopted during the execution of work :- (i) Demolition of existing treatment of any type including cleaning and removal of debris from site. (ii) First layer of slurry of cement @ 0.488 kg/sqm mixed with Acrylic based polymer modified cementitious composite compound @ 0.253 kg/sqm. The layer will be allowed to air cure for 4 hours. (iii) Second layer of slurry of cement @ 0.242 kg/sqm mixed with with Acrylic based polymer modified cementitious composite compound @ 0.126 kg/sqm. The layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. Contd/---101

Contd/---100 (iv) 20mm thick screed in cement mortar 1:3 mixed with liquid water proofing compound as per manufacturers instructions above the treated area. (v) Ponding the treated portion atleast 48 hours. if any leakage/seepage observed the entire procedures will be repeated without any extra cost. (vi) Provide 40mm dia light grade GI spout at the lowest point with 30cm projection beyond the out face of the wall. (vii) Sunken portion shall be filled with lean concrete 1:5:10 type E-2(using 40mm graded stone aggregate). Note :- (i) The sunken slab sloped towards outer face so as the drain the water to GI Spout pipe. (ii) Coving shall be provided at the junction of slab with the wall. (iii) Nahni trap shall be 10mm below finished floor level. Ensure the drain of pipe dia is larger than the nahni trap size. (iv) The outer end of the spout should be chamfered.

M&L for Complete removal of existing treatment on wall and applying two coat of oil bound distemper white or tinted over a coat of alkali resistent primer over 1mm thick putty complete all as specified and directed

Supply & fix of GI frame work for seam less ceiling comprising of GI perimter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to sorrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.90mm thick having two equal flanges of 15mm eachand web of 45mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section(Not exc 1.2m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediat channel with connecting clips across the intermediate channel at 457 mm centre to centre,hangers 6 mm dia GI (Up to 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long, Providing and fixing PVC decorative ceiling 5-6mm thick fixed with screw as per manufacturers instructions including finishing the joint of face board complete all as specified and directed including taking down old ceiling of any description

Supply & fix of GI frame work for seam less ceiling comprising of GI perimter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to sorrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.90mm thick having two equal flanges of 15mm eachand web of 45mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section(Not exc 1.2m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediat channel with connecting clips across the intermediate channel at 457 mm centre to centre,hangers 6 mm dia GI (Up to 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long, Contd/--105

Contd/--104 Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions including finishing the joint of face board with specially formulated jointing compound and 48mm wide fibre tape to provide seam less finish, incl necessary preparation of new surface and apply two coats of oil bound distemper over a coat of alkali resistant primer on ceilings complete all as specified and directed including taking down old ceiling of any description

Demolition of existing roof treatment of any type including cement plaster 15 mm thick and providing screed bed/rendering 10mm thick in CM (1:3) mixed with and including supply of approved water proofing compound as per manufacturers instructions by removing all loose gravel, dirt, oil, grease and foreign materials by jet or dry air, cleaning the surfaces mechanically or by grinding to make it smooth and applying APP modified water proofing membrane as per IS 1654-2017/IS 16352-2017 , 3mm thick and weighing not less than 3.60kg/Sqm reinforced with non woven polyster/HMHDPE matt black finished over compatible primer/bonding bitumen @ 0.40 Litr/Sqm and torch applications of membrane with 75mm side overlap and 100mm end lap after necessary preparation of surface complete as per manufacturer's instructions and applying a coat of solar reflective bituminous aluminum paint on top @ 0.10 litre/sqm complete all as specified and directed.

M&L providing cement concrete type B0 1:2:4 (12.50mm graded stone aggregate) in copings, parapets and railing upto 60cm height, leveling concrete for Roof slab, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed

Material and labour for spraying antiweed / non toxic solution / chemicals containing Glyphosate as per manufacture instructions and removing the weed including the roots after ensuring complete de-germification of palnt/weed and cutting down the plant/trees off from roof/top sides of external walls of bldgs, in chajjas, wall junctions, junctions of GI/CI/AC/PVC pipes and taking out roots entered in wall/slabs, including making good the surface using PCC 1:2:4 type B1 or cement mortar (1:2) or brick work in CM(1:4) plastered with CM(1:4) to match with existing surface and repairing the pipes and joints which was affected by cutting down/taking out process all as specified and as directed for plants / trees located in the buildings upto four storey high, complete all as specified and directed by Engineer-in-charge. NOTE:- Contractor has to execute the work of de-generated plant/weeds as per the prior approval and directions of Engineer-in-charge.

S & F in repair 75 mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including necessary fittings all as specified and as directed.

All as per item No 109 above but 110 mm dia .

S&F in repair 75mm dia PVC (SWR) Bends with access door of any radius

All as per item No 111 above but 110mm dia

S&F in repair 75mm dia PVC (SWR) junction single (single T) equal or unequal with access door

All as per item No 113 above but 110mm dia

S&F in repair 110mm dia PVC(SWR) brach piece, single (single Y) equal or un equal with access door

All as per item No 115 above but 75mm dia

S&F in repair 110mm dia PVC(SWR) brach piece, (double Y) equal or un equal with access door

All as per item No 117 above but 75mm dia

S&F in repair 75mm dia PVC(SWR) vent cowl

All as per item No 119 above but 110mm dia

Taking down carefully aluminium/ copper wiring/power point wiring (light, fan, call bell socket or power circuits) complete and making good the disturbed surface of walls, ceiling etc incl painting with same colour of the back ground complete all as specified and as directed by Engineer-in-Charge.

Point wiring complete concealed with 1.5 Sqmm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and incl non-metalic rigid PVC conduit medium grade ISI marked incl accessories concelaed type wiring incl GI/ MS branded sunken boxes suitable for normal/modular concealed on walls including plastic/heylam laminated sheet top cover 3 mm thick/modular frame and cover of suitable module fixed with cadmium plated iron screws for housing modular/normal type switches, switch socket outlets, fan regulators etc., incl provision of 1.5 Sqmm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed.for the following (a) One light point controlled by one switch

All as per tem No. 122 above but for (b) One fan point controlled by one switch/regulator

All as per tem No. 122 above but for (c) One light point controlled by 2 way switch

All as per tem No. 122 above but for (d) One 3 pin socket out let 5 Amps on independent board

All as per tem No. 122 above but for (e) one bell/buzzer point controlled by bell push

All as per tem No. 122 above but for (f) one 3 pin socket out let 5 A on same board

All as per item No 122 but concealed wiring drawn through existing PVC conduit for (a) One light point controlled by one switch

All as per tem No. 128 above but for (b) One fan/Exhaust point controlled by one switch/regulator

All as per tem No. 128 above but for (c) One light point controlled by 2 way switch

All as per tem No. 128 above but for (d) One 3 pin socket out let 5 Amps on independent board

All as per tem No. 128 above but for (e) One bell/buzzer point controlled by bell push

All as per tem No. 128 above but for (f) One 3 pin socket out let 5 A on same board

Point wiring complete with 2.5 Sqmm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through non-metalic existing PVC conduit medium density ISI marked incl accessories surface type run on walls/ ceiling incl MS terminal boxes fabricated with 1.6 mm thick MS sheet surface mounted/ concealed on walls with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., incl provision of 2.5 Sqmm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed.

Sub main wiring complete with two runs of 4 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable with one run of 4 sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through existing non metallic rigid PVC conduit and conduit accessories all as specified and as directed. Note:- 3 runs of cable will be measured as unit length

Point wiring complete with 1.5 Sqmm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and incl PVC Casing & Caping ISI marked incl accessories surface type wiring incl 1.6 mm thick MS sunken boxes concealed on walls including laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., incl provision of 1.5 Sqmm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed.for the following (a) One light point controlled by one switch

All as per tem No. 136 above but for (b) One fan point controlled by one switch/regulator

All as per tem No. 136 above but for (c) One light point controlled by 2 way switch

All as per tem No. 136 above but for (d) One 3 pin socket out let 5 Amps on independent board

All as per tem No. 136 above but for (e) one bell/buzzer point controlled by bell push

All as per tem No. 136 above but for (f) one 3 pin socket out let 5 A on same board

Point wiring complete with 2.5 Sqmm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and incl non-metalic PVC conduit medium density ISI marked incl accessories concealed type run on walls/ ceiling incl MS terminal boxes fabricated with 1.6 mm thick MS sheet concealed on walls with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., incl provision of 2.5 Sqmm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed.

Point wiring complete with 2.5 Sqmm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and incl PVC casing caping ISI marked incl incl accessories surface type wiring run on walls/ ceiling incl MS terminal boxes fabricated with 1.6 mm thick MS sheet concealed on walls with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., incl provision of 2.5 Sqmm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed. Note for Item No 125 to 146 :- (i) The earth wire for the points in the same circuit can be looped from point to point (ii) Earth wire shall be taken inside the conduit (iii) Cost of terminal box is deemed to be included in the item rate quoted for point wiring (iv) Cost of a circuit of any length of cable from DB to any switch/ socket board to be included in point wiring. (v) Cost of cutting chases for conduits and making good to walls, in case of recessed or concealed conduit wiring will be paid separately in other items.

M&L for groove cutting in wall/floor and making good of distrubed wall/floor, painting of existing colour all as specified and directed by Engineer -in-Charge.

Fixing only 20W LED Fittings complete with all accessories including taking out old fittings all as specified and directed. (LED Fitting will be Issued under SCh 'B' item Note:-Note:- LED fitting will be issued under Sch 'B' free for fixing only)

Fixing only LED batten suitable for indoor applications 10 Watts, 2 feet complete with all accessories including taking out old fittings all as specified and directed. Note:- LED batten will be issued under Sch 'B' free for fixing only)

S&F 2 x 2 Recess mounted LED Luminaire 36 Watts white powder coated CRCA housing with LEDs seamless front frame with flate white high transmission arcylic cover complete with all accessories all including taking out old fittings as specified and directed. Make: Bajaj, Cat No : BZRSQL 36W GZi WH or equivalent Makes & model in Havells/ Philips.

Supply and Fix Modular switch 1 way 6A,1 module

Supply and fix Modular switch 1 way 16A, 1 module

Supply and fix Modular switch 2 way 6A,1 module

Supply and Fix Modular Bell push 6A 1 module

Supply and fix modular Socket, 6A - 2/3 pin combined 2 module

Supply and fix modular Socket 6A/16A - 2/3 pin combined 2 module,

Supply and fix modular type Fan step regulator, 120W - 2 module

S&F in replacement of of Switch piano flush button single pole two way 5 Amps all as specified and as directed.

S&F in replacement of Angle holder PVC / polycarbonate type all as specified and as directed

S&F in replacement of switch piano flush type single pole one way 5amps

S&F in replacement of switch socket combination 5 pin 2 in 1, 5 A Flush type all as specified and as directed

S&F in replacement of switch socket combination 2 in 1, 3 pin 5 and 15 Amps flush type universal all as specified and as directed

S&F in replacement of socket outlet 2 in 1, 3 pin 5 A all as specified and as directed

S&F in replacement of bell push flush type 5A all as specified and as directed .

S&F in replacement of MCB SPN 240 volts 32/40 Amps complete all as specified and as directed

S&F in replacement of MCB single pole 240 volts 10/16/20/32 Amps complete all as specified and as directed

S&F in replacement of MCB TPN 415 volts, 10KA 'C' curve 63 Amps complete all as specified and as directed

S&F in replacement of MCB TPN 415 volts, 10KA 'C' curve 100 Amps complete all as specified and as directed

S&F in replacement of MCB DB SPN 4 way double door type 240 volts with 200 Amps rated busbar as specified and as directed.

S&F in replacement of MCB DB SPN 8 way double door type 240 volts with 200 Amps rated busbar as specified and as directed.

S&F in replacement of MCB DB TPN 4 way with double door type 415 volts with 200 Amps rated busbar for housing MCBs as specified and as directed.

S&F in replacement of ceiling rose, surface bakelite type 65 x 50 mm, 2 to 3 terminals all as specified and as directed

S&F in replacement of stepped type electronic fan regulator flush Switch/socket type all as specified and as directed

S&F in replacement of Ding Dong bell AC 230 volts single pole.

Removing of old existing unserviceable one and provision of new sub main wiring 1100 volts grade multistranded FRLS copper conductors, two runs of single core 6 Sqmm along with one run of 6 Sqm PVC insulated single core multistranded copper conductor cable as earth continuity conductor run along with PVC conduit all as specified and as directed Note :- 3 runs of cable and one run of conduit will be measured as unit length.

Removing of old existing unserviceable one and provision of new sub main wiring 1100 volts grade multistranded FRLS copper conductors, two runs of single core 4 Sqmm along with one run of 4 Sqm PVC insulated single core multistranded copper conductor cable as earth continuity conductor run along with PVC conduit all as specified and as directed. Note :- 3 runs of cable and one run of conduit will be measured as unit length.

Removing of old existing unserviceable one and provision of new sub main wiring 1100 volts grade multistranded FRLS copper conductors, two runs of single core 2.5 Sqmm along with one run of 2.5 Sqm PVC insulated single core multistranded copper conductor cable as earth continuity conductor run along with PVC conduit all as specified and as directed. Note :- 3 runs of cable and one run of conduit will be measured as unit length.

M&L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of earth plate at a depth not less than 1.5 mtr connected to galvanized earth lead wire 4 mm dia as earth lead up to 7.5 mtr long by means of nuts, bolts, thimbles,check nuts and washers etc made of galvanized iron connected to earthing test point all as shown in electrical plate No 3 of SSR Part-I 2010 and as specified or indicated and testing on completion incl earth work and excavation in any type of soil PCC (1:3:6) type C1 chamber, pre cost slab 40mm thick in cement concrete (1:2:4) type B1 with 8 mm dia MS bars reinforced at 10 cm centre to centre both ways incl funnel with watering pipe wire mesh and lugs, incl test point complete all as specified and as directed.

S&F LED lamp suitable to fit in angle holder of capacity 09 watt. Make: Bajaj or eqv in Philips / Havells / CG.

Supply and fixing 30 W LED bldg security light fitting with pressure die cast housing along with prismatic polycarbonate difuser with IP 66 protection including taking out old fittings. Make:- Bajaj, Cat No.:- ENXT P 30L WH SY PC SD or Equivalent Makes & model

S&F Bracket made out of GI tubing medium grade 25 mm bore , approx length 1.5 m long including MS clamps made out of MS flat iron 25 x 6 mm , nuts, bolts, washers etc and including before fixing applying two coats of aluminum paint over a coat of red oxide primer including removing the old existing GI bracket from bldg complete all as specified and directed.

S&F Exhaust fans AC single phase 230/ 240 V of size 250/280/300 mm sweep with louvers fixed outside with all accessories and fixing the exhaust fan from ceiling rose with 3 core flexible copper wire 24/0.20 sqmm , etc all as directed.

M/S SIRI BUILDERS

ABHISHEK CONSTRUCTIONS

Sreyas Enterprises

RAJINDER SINGH RATAN

J PUSHPALATHA ENGINEER AND CONTRACTOR

Shanmuga Constructions

K. VENKATESH NAIDU

ADWITHI