Interior fitout work in the office space of the MSTC at world trade centre, Tower J, 5th floor Nauroji Nagar, New Delhi

BILL OF QUANTITIES (BOQ)

S.No. Sub-Head DSR Amount (in Rs.) NDSR Amount (in Rs.)

1 CIVIL & INTERIOR WORKS 13,842,481.51 12,305,095.66

5 AUDIO- VIDEO WORKS 0.00 16,146,477.69

6 PLUMBING & FIREFIGHTING WORKS 2,488,684.40 1,012,892.13

TOTAL i/c GST 93,000,718.00

Digitally signed by AMIT

Interior Fit-Out Works in The Office Space of the MSTC at World Trade Centre, Nauroji Nagar, New Delhi

Summary of Civil and Interior Works

S.No. Description of Works Amount

Amount (SR, in Rs.)

2 Masonry & Plaster

3 Paving, Flooring & Wet Works

4 Partitions & Wall Cladding

7 Finishes & Miscellaneous

GRAND TOTAL (Carried Forward) 26,147,577.17

GRAND TOTAL (Carried Forward) 26,147,577.17

Digitally signed by AMIT

Interior Fit-Out Works in The Office Space of the MSTC at World Trade Centre, Nauroji Nagar, New Delhi

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

CIVIL & INTERIOR WORKS

2 MASONRY AND PLASTER

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement

concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland

Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS:

9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing

strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the

cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades

Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable

separately. In case the cement content in design mix is more than 110% of the minimum specified cement

content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

4.20.2 All works above plinth and upto floor V level

4.20.2.2 Concrete of M15 grade with minimum cement content of 240 kg /cum cum 110.00 9,341.80 1,027,598.00

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC

blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with

approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-

Charge. (The payment of RCC band and reinforcement shall be made for seperately).

2.4 13.2 CEMENT PLASTER :- 15 mm cement plaster on the rough side of single or half brick wall of mix.

2.5 13.4 12 mm cement plaster of mix

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings,

balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five

level excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 2

coarse sand : 4 graded stone aggregate 20 mm nominal size).

2.7 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

2.8 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers SQM 10.00 736.40 7,364.00

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding

all complete above plinth level.

5.22A.4 Hot rolled deformed bars kg 60.00 107.85 6,471.00

POP PUNNING (12mm-15mm) : Providing and fixing Average 12mm to 15mm thick POP Punning over

cement plaster in line & plumb finished smooth to receive paint. (Internal surfaces of walls).

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying

cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of

cement @ 0.488 kg /sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be

2.11 22.5 allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/ sqm mixed with water SQM 165.00 617.05 101,813.25

proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with

water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints,

corners, junctions of pipes and masonry with polymer mixed slurry.

AAC BLOCK FILLING: Providing and Laying of AAC Block Filling in the Slab Sunk or Raised Areas as a Back fill

or platform. Laying should be done in layers with pounding done at every level to ensure a proper cavity

free installation without disturbing any existing services in the area. Cost to also include haunching for

plumbing pipes.

SUB TOTAL OF MASONRY AND PLASTER 2,003,255.50 167,928.59

3 PAVING, FLOORING AND WET WORKS

Digitally signed by AMIT

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by

the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any

3.1 8.31 size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of SQM 200.00 1,267.95 253,590.00

cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,

including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer)

with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all

colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey

3.3 11.41A cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The

tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch

trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently

b 11.41A.2 Glazed vitrified floor tiles polished finish of size

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be

specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours,

3.4 11.40 shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 SQM 420.00 1,439.40 604,548.00

Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement

and matching pigments etc., complete.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic

3.6 MR coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting

and finishing complete as per direction of Engineer-in-charge.

KITCHEN/ PANTRY/ HAND WASH COUNTER :- Providing and fixing pantry and toilets with Granite stone top

(with straight edge polished nosing) complete with base cabinet made of 20mm BWP board, outside

surface (shutters) finished in 1mm thick Laminate of approved shade. All internal surfaces to have balancing

laminate. The rate inclusive of necessary hardware, handle lock sets, self closing hinges, spring loaded

shutter, latch inside, all cabinet hardware complete as per Architects approval. (BR of stone to be taken as

Rs 1600/Sqmt). Width of work top counter 600mm/ detailed drawings.

Carpet- Supply and installation of modular carpet (including skirting) of approved model and shade and

made with 100% nylon 6/6.6 tufted textured tiles of minimum 500mm x 500mm in size, stain resistant, anti

microbial, and having colour fastness to water, fastness to light, rubbing fastness and castor chair suitability

as per relevant standard for heavy commercial usage, with 100% PVC free Wellbac Function Backing with

having average density 6000 oz/cu. yd. or more,Nominal total thickness of 5.9mm, and Pile weight – 16-18

oz/ sq yard. Material shall be CRI GREEN LABEL PLUS certified, and shall have recycled content complying to

GRIHA requirement, including fixing with GRIHA compliant adhesive of approved make, minimum 15 years

manufacturer's warrantee, all complete as per drawings, manufacturer's specifications.

Providing and fixing removable raised/false access flooring with system and its components of approved

make for different plenum height with possible height adjustment upto 50 mm,comprising of modular load

bearing floor panels supported on G.I. rectangular stinger framework and G.I. Pedestal etc. all complete, as

per the architectural drawings, as specified and asdirected by Engineer-in-charge consisting of:

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness

minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x

3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI

fully threaded stud 16mm outer diameter with two GI

Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head

in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using

epoxy based adhesive of approved make or the machine screw with rawl plug.

Digitally signed by AMIT

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

(b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm

thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded

screws ensuring maximum lateral stability in all directions, the grid

formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide

adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted

clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the

architectural drawings, as specified and as directed by

the Engineer-in-charge

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high

pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an

enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel

Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome

and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection

and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious

core mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static

High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface

flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x

25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will

withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all

complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge.

All specification must be printed on the side of the panel to ensure the quality of the product.

11.54.1 300 mm Finished Floor Height (FFH) SQM 80.00 5,623.95 449,916.00

ENGINEERED WOOD FLOORING:Providing and Fixing of Compct ENGINEERED WOODEN FLOORING Panel

12.5x145 x 1820 Total thickness 14 mm Numbers of panels per pack 6 Nested Lengths Max. 1 plank out of 6

m2 per pack 1,583 m2 Kg per pack 11,99 kg Toplayer PEFC controlled sources EN 13489 ± 3 mm Core board

PEFC controlled sources Spruce Backing layer PEFC controlled sources Wood Veneer 2 mm Tongue and

groove Length Uniclic Width Uniclic Multifit Domestic use Conditions in each pack 33 years Uniclic - Multifit

connection Lifetime Commercial On request "Wood for Life" Edge Protect + Provides a warranty on build-up

of residue dirt along the edges due to maintenance over the years 10 years "Wood for Life" Surface & Edge

Protect + (lacquered products only) Provides a warranty on pollution of surface structure and a warranty on

build-up residue dirt along the edges due to maintenance over the years 10 years Surface layer Wood

species Oak Origin Europe Finishing UV cured Oiled finish 2 layers UV cured Lacquer Anti-scratch top coat 5 -

7 layers Natural variance Due to nature, visual surface can deviate from samples Surface treatments cf

catalogue/website Nature Marquant Vibrant General aspect of installed EN 13489 Lipping - difference in

height (mm) ≤ 0,20 difference in width (mm) ≤ 0,20 cupping lengthwise % ≤ 0,1 cupping in width % ≤ 0,2

Dimensional stability ISO 24339 Cupping short side max % ≤ 0,30 Changes 30 - 85 % RH Cupping short side

min % ≥ - 0,20 Open joints short side (mm) ≤ 0,20 Open joints long side (mm) ≤ 0,30 Underfloor heating

Suitable of special installation instructions.or its equivalent as per direction of Engineer Incharge

TOTAL FOR PAVING & WET WORKS 3,646,494.00 2,084,577.19

4 PARTITIONS AND WALL CLADDING

Digitally signed by AMIT

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

GYPSUM PARTITIONING:- Providing and fixing partition upto ceiling height consisting of G.I. frame and

required board, including providing and fixing of frame work made of special section power pressed/ roll

form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel

50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing

of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor

4.1 9.105 fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other

flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a

spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of

partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450

mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on

studs, floor and ceiling channels at the spacing of 300 mm centre to centre.

The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing

channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal

joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing

to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25

mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification

and direction of engineer in charge all complete.

75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG)

plaster board conforming to IS: 2095:

75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board

conforming to IS: 2095: (part I): 2011 (Board with BIS certification marks)

Gypsum Panelling:-Providing and fixing, in position concealed G.I. section for wall paneling using board of

required thickness fixed on the ‘W’ profile (0.55 mm thick ) having a knurled web of 51.55 mm and two

flanges of 26 mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one

flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm.

4.2 9.133 Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully

threaded self-tapping dry wall screws. Board is fixed to the ‘W’ profile with 25 mm countersunk ribbed head

screws @ 200 mm C/C., all complete as per the drawing & directions of engineer-incharge, the joints of the

boards are finished with specially formulated jointing compound and 48 mm wide jointing tape to provide

seamless finish.

9.133.3 Gypsum board conforming to IS: 2095 Part - I

GLASS PARTITIONING:- Providing & Fixing Full Height Glass partition using 12mm Thk. Glass with anodised

Aluminium frame fixing glass with snap on option consisting of top, bottom and side frame measuring 40-

46mm x 18mm-26mm complete with glazing rubber as per manufacturer's specifications and instructions of

4.3 MR Engineer- in-charge. Rate include supply & Installation of 12 mm thk toughened glass with double sided SQM 200.00 5,584.34 1,116,867.38

adhesive tapes for glass to glass butt joints. Partition system from FFL to False Ceiling level, inclusive of cost of

support required for fixing in the ceiling. The frame to be powder coated in desired shade as per the

instructions of the Architect.

PARTITIONING- Partition using 12mm HDHMR board fixed on both sides on aluminium Studs Frame 50mm x

4.4 MR 50mm x 1.5mm as per approved sample and architectural drawings placing the same 600mm c/c. SQM 20.00 3,355.00 67,100.00

Aluminuim frame to be fixed to floor and RCC Ceiling using fastners.

PANELLING- Panelling using 12mm thick HDHMR board fixed on one side on Aluminium Frame 50mm x

4.5 MR 25mm x 1.5mm as per approved sample and architectural drawings. Aluminium frame to be fixed to walls, SQM 20.00 2,384.78 47,695.70

floor and RCC Ceiling using fastners.

4.6 MR Cladding using 12mm thick HDHMR board on existing frame/ surface. SQM 20.00 1,370.18 27,403.60

VEENER CLADDING- Providing and Fixing 4.0 mm thick decorative/ Natural Veneer of approved design and

4.7 MR shade , cladded on to existing partitioning. Complete Cladding to be finished using mellamine polish SQM 75.00 3,500.00 262,500.00

(gloss/matt) as approved by the architect. (base rate Rs. 1450/- sqm)

Digitally signed by AMIT

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede

4.8 9.127 finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to

IS : 2046 Type S, including cost of adhesive of approved quality.

Providing and fixing of 4mm thick MDF on existing frame, GRG board, HDHMR board, Gypsum board with

4.9 MR the necessary screws, fixing arrangements, as per design and detail. The cost to include making in grooves SQM 2,000.00 794.51 1,589,016.93

of size and design as specified by the architect including fixing accessories complete.

Providing and fixing of 1.5 mm(+/-0.15 mm) thick high pressure decorative laminates (conforming to

applicable IS:2046-1995, EN 438-3: 2016, NEMA LD3-2005 quality standard), made out of urea free,

thermosetting phenolic resins treated Kraft papers as core material and Amino plastic resin treated decor

papers on the finish surface. Performance properties of laminates must meet having a minimum density of

1.35g/cm3 and possess Anti-viral, Anti-Fungal & Antibacterial properties and fulfil the criteria of FSC,

4.10 MR Greengard-Gold, GRIHA & GreenPro certification. Surface of laminates accomplice the properties as per SQM 25.00 4,631.86 115,796.44

classification HGS Grade for Resistance to surface wear (350 revolutions), Resistance to cigarette burns

(Rating-Not worse than 3) , Resistance to staining(Rating 5), Resistance to dry heat @180°C (Rating 4),

Resistance to cracking ( >4 rating) & Resistance to scratching(>2.0 N) . Resistance to Color Change-Xenon

Arch Lamp (Rating 5/Index 6). Color/Decor, size and finish of laminates should be agreed and finalized

under direction of the in-charge. The cost to include providing and fixing to MDF for base of laminate.

INSULATION- Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183,

having density 48 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall wirh screw, rawel

plug & washers and held and in position by criss cossing GI wire etc. complete as per directions of Engineer-

Providing and Fixing Channeled Woodworks perforated panels of width 192mm, thickness of 15mm and

length 2400 mm or as specified by the Architect/ approving engineer, made of a high density fibre board

with minimum 725 Kg/M3 density substrate with a laminated facing as per the approved shade & finish and

a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where

4.12 MR the visible surface has a “Helmholtz” fluted perforation of 3mm width and 5mm/13mm/21mm of visible SQM 60.00 4,132.11 247,926.50

panel each. The edges of the panels shall be “tongue-and-grooved” to receive special clips for installation.

The back of the perforated panel shall have sound absorbing non-woven acoustical fleece having NRC of

0.52-0.63. The panels shall be mounted on special aluminium splines using clips. The works to be done

complete as per drawings and satisfaction of engineer-in-charge.

Providing and supplying Acoustical Wall Paneling with square edges made of fibre glass substrate 9 mm

thick and wrapped on the front side with an acoustically transparent and classified for Fire reaction Class A

4.13 MR as per ASTM E-84, fabric as per the selection of the Architect of approved size providing a minimum sound SQM 50.00 4,526.34 226,316.99

absorption level of 0.85 NRC to be affixed to wall using Wall panel impalers and construction adhesives as

per the instructions laid down by the manufacturer.

Providing and fixing of 12mm thick MDF sheet over existing frame/ surface. The cost to included making

pattern in MDF sheet using CNC router cutting in approved pattern and design complete.

SHELVES:- Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded

wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade

I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be

painted with polyurethane primer (fittings to be paid separately).

LAMINATED STORAGE CABINET FOR GENERAL STORAGE- Out of 19mm Commecial Ply Board finished using

1mm thick Laminate. The storage to be complete with all hinges, drawer glides and hardware from

4.16 approved make. All internal surfaces to be completed using balancing laminate. Including brass D-type SQM 20.00 10,250.00 205,000.00

handles for shutters and recessed type handles for drawers or as approved. Storage to be of all heights as

per design. Storage shutters to be made in solid laminate/ glass as per design and drawings.

DISPLAY SHELFS - Out of 19mm Commecial Ply Board finished using 1mm thick Laminate. The cabinet to be

4.17 complete with all hinges, drawer glides and hardware from approved make as required. All internal SQM 5.00 9,800.00 49,000.00

surfaces to be completed using 1mm laminate. Storage to be of all heights as per design.

Digitally signed by AMIT

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

STORAGE CABINET FOR ELECTRICAL PANEL AND VOLTAGE STABLIZERS- Cabinet Shutters out of 19mm

Commercial Plybaord finished in 1mm Laminate of base cost Rs. 380 per sqmt. Shutters to be fixed to a

frame. Rigidly fixed on both sides and top finshed in laminate. No internal carcass required. All Hinges of

hettich or equivalent. Internal Surface of the shutter in balancing white laminate. All shutters to be provided

with Stainless steel louvers at the top and bottom of the shutter as per the site requirements and instrcution

of the Engineer In charge.

SUB TOTAL OF PARTITIONS AND WALL CLADDING 4,862,555.07 4,072,230.82

GYPBOARD CEILING :- Providing and fixing false ceiling at all height including providing and fixing of frame

work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120

gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm

thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with

dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers

of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed

with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to

which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each

having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every

junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm

Including jointing and finishing to a flush finish of tapered and square edges of the board with

recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering

upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's

specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made

with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of

the Engineer in Charge but excluding the cost of painting with :

a) 12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I SQM 1,300.00 1,355.80 1,762,540.00

Providing and fixing suspended cloud ceiling, Size 1200X2500X12.5mm round random perforation G8/15/20

with 9.9% perforation, NRC upto 0.55 : Round rectangular perforation of glass-fibre reinforced gypsum

material, which includes providing and fixing GI perimeter channels of size 0.55 mm. Thk. having one flange

of 20 mm and another flange of 30 mm and web of 27 mm along the perimeter of the ceiling, screw fixed

to brick wall/ partition with help of nylon sleeves and screws, at 610 mm centers. The suspended GI

intermediate channels of size 45 mm,0.9mm thk with two flanges of 15 mm each from the soffit at 900 mm

centers with ceiling angle of width 25mm x 10mm x 0.55mm thk fixed to soffit with GI cleat and steel

expansion fasteners. Ceiling section of 0.55 mm thk having web of 51.5mm & two flanges of 26mm each

with lips of 10.5mm are fixed to the intermediate channels with help of connecting clips and in direction

perpendicular to the intermediate channel with centers of 333 mm perforated gypboard is then screw

fixed to ceiling section with 25 mm dry wall screws at 300 mm centers to G.I. framing in perfect level. Screw

fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally the

boards are to be joined and finished so as to have a flush look with uniflot.

The false ceiling surfaces shall be prepared to the satisfaction of the Architect/engineer in charge.

Digitally signed by AMIT

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture,

design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ? 85%, Thermal

Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level

suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick

(galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size

15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form

grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item

5.3 26.27 (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded

hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm

centre to centre along main ‘T’.The system should rest on periphery walls /partitions with the help of GI

perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help

of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom

portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint,

for all heights. The work shall be carried out as per specifications, drawings and as per directions of the

engineer-in-charge.

26.27.1 With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6) SQM 150.00 2,333.60 350,040.00

TRAP DOOR :- Providing and fixing trap door in false ceiling made of "Novapan "pre-laminated board with

5.4 MR hardwood framing, dead locks, lapping all around including all hardware, hinges etc. complete as per SQM 5.00 3,098.17 15,490.87

design and drawing.

CEILING PELMETS :- Providing and fixed pelmet of overall size 150mmx150mm and made hardwood

5.5 MR framings hung from ceiling @1000mm centre to centre with 2 nos of 6mm thk. Commercial ply on vertical & RMT 150.00 1,161.07 174,160.94

12mm thk. Commercial ply on horizontal surface (straight & curved). Inclusive of finishing in Paint.

WOODEN VENEER CEILING :- Providing and fixing wooden veneer ceiling by Fixing Natural Teak Veneer on

12mm Underlay commercial Ply fixed to a subframe made using 50mm X 50mm Kiln seasoned and

5.6 MR chmeically treated hollock wood fixed to RCC ceiilng using Fastners . The cost to inlcude the finishing of the SQM 30.00 6,756.06 202,681.71

Veneer using wood stain and clear coat of PU (Gloss/ Matt) as per the instructions of the Engineer In

Charge. (base rate Rs. 1450/- sqm)

Providing the gypsum double sided cove of 150mm x 150mm having a facia of 75mm to macth the

specifications same as gypsum ceiling.

Providing the gypsum single sided cove of 150mm x 150mm having a facia of 75mm to macth the

specifications same as gypsum ceiling.

Providing the wooden cove of 150mm x 150mm having a facia of 75mm to macth the specifications same

GYPSUM BOARD VERTICAL BAND- upto100mm high gypsum band all round the mineral fibre/ gypsum

5.9 MR ceiling. In order to make the Mineral Fiber/ gypsum ceiling higher than the Gypsum Ceiling by upto 100mm RMT 135.00 371.61 50,166.91

as per drawings. (visible surface of gypsum band to not exceed 100mm) including plastic emulsion paint.

Providing of Baffle ceiling system comprises of 50 mm x 100 mm (50 mm width & 100 mm Height) U Shape

panels in wooden finish or as approved. Panels shall be made of 0.5 mm thick galvanized steel after

Powder-coated and length up to 4000 mm. Panel shall be high corrosion resistance and good color

stability. Centre to Centre panel gap will be 100 mm. Panels are fixed on to roll formed carriers 20 mm wide

x 40 mm deep out of 0.80 mm G.I sheet Powder-coated color with cutouts to hold the panels in module of

50 mm at maximum 1200 m c/c. Carriers are suspended from the roof or truss by 6 mm dia. galvanized steel

wire rod hanger with special height adjustment suspension clip at max. 1200 mm c/c. Hangers are fixed to

the roof by ‘J’ hooks or ceiling brackets and nylon inserts. Panels are factory cut in lengths up to maximum

4.0 m to suit site dimensions or shop drawings. Top cap and side cap are used to cover the edges of the

SUB TOTAL OF CEILING 2,112,580.00 1,298,374.22

6 DOORS/ WINDOWS

35MM THICK VENEER FLUSH DOOR WITH FLOOR SPRING- 35mm thick flush Doors of size upto 2400mm x

1050mm complete with Hardware including floor spring, Door Closer, dead Lock with inbuilt key, D-Handle

etc. including cost of teak lipping all around with melamine/ duco finish. The item to include installation of

all kinds of latches as per the requirement.

Digitally signed by AMIT

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

DOOR FRAMES- Providing wood work in frames of doors, windows, clerestory windows and other frames,

6.2 9.1 wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold

fast lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood CUM 0.80 142,949.70 114,359.76

LAMINATED FLUSH DOOR- Flush Doors finished using 1mm Thick Laminate on both sides panel of size upto

2400mm x 1000mm complete with Hardware including hinges, Door Closer, Mortice Lock with Handle,

latches etc. including cost of Door frame with melamine/ duco finish. The cost to include providing and

fixing of vision panel as per design.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts

6.4 9.53 and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse EACH 102.00 228.85 23,342.70

sand : 6 graded stone aggregate 20mm nominal size).

DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor door stopper with necessary

screws, etc. complete.

FIRE DOOR- Providing and fixing single leaf 120min Rated Fire Door of size 900x2400. with vision panel using

wired glass complete with Fire proof door frame. One side to be finished in fire retardant paint and one side

to be finished in Laminate of approved shade. All Frame to be finished in fire retardant paint. All hinges and

hardware to be thermatically sealed and 120 mins fire rated.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and

manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and

making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-

Providing and fixing of SS 1200mm long D handles to glass/ flush door in approved shade and finish

including all required fitting complete as per instructions of engineer-in-charge.

Providing and fixing of SS bottom patch lock on glass doors in approved shade and finish including all

required fitting complete as per instructions of engineer-in-charge.

Providing and fixing of SS half moon stopper with rubber bumper in approved shade and finish including all

required fitting complete as per instructions of engineer-in-charge.

SUB TOTAL OF DOORS 597,794.94 701,329.79

7 FINISHES & MISCELLANEOUS

PRIMER: Applying one coat of water thinnable cement primer of approved brand and manufacture on wall

surface. Water thinnable cement primer.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic

7.2 13.83 Compound ) content less than 50 grams/ litre. of approved brand and manufacture, including applying

additional coats wherever required to achieve even shade and colour.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the

surface even and smooth complete.

Painting of walls, ceiling, RCC works, HVAC ducting, grills diffusers, conduits etc. with 2 or more coat of duco

paint to achive smooth finish. The item to include cost of all base preparation, priming etc. complete.

Steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer using structural steel etc. as required.

10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works kg 150.00 172.60 25,890.00

7.4 13.61 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:

13.61.1 Two or more coats on new work SQM 300.00 155.90 46,770.00

Digitally signed by AMIT

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

HONEYCOMB BLINDS -Providing & supplying of fabric venetian Window Blinds as per the approved sample,

consisting of 3" vane size having head rail, rotator rail and bottom rail made of aluminium alloy 6063-T6 PER

ASTM B221 - 85 extruded profile, powder coated and provided in standard natural white color. The rolling

tube should be made up of aluminium alloy from extruded profile of 34 mm die. The head rail dimensions

should be of suitable size according to the length of head rail and space available and finished with fabric

cover matching with the louver fabric. The cassette should conceal the working mechanism rotary-clutch.

(White polycarbonate spring tempered rotary clutch which raises), lower and tilts the blinds. White

polycarbonate limit assemblies control vane over-rotation, located on either side of individual blinds. The

room darkening fabric of Blind should be of anti-static polyester vanes which have facings between two

sheer layers (50 mm wide) to reduce glare. Sheer layers should be of white 100% knit polyester, the colors,

textures and opacities as approved. The fabric shall be made of spun- bonded 100% polyester fiber (having

green guard certification) treated with soil & dust repellent requiring minimum regular interval cleaning.

GREEN GUARD Gold certified for low-emitting products to maintain Indoor environment. Upto 80% ultraviolet

protection with vanes open and 90% with vanes closed. The shading to be operated by Easy rise

mechanism with a continuous cord loop operating system. All parts, components & hardware are in

approved shade as per direction of Engineer-in-charge.

ZEBRA BLINDS -Providing & fixing of Twist Window Shadings Blinds as per the sample shown having room

darkening fabric strip and sheer fabric strips alternately in such arrangement as when light filering strips

overlap each other, it creates visibilty and once the light filtering strips overlaps the sheer ones, it creates the

no visibility effect.It has bottom rail made of aluminium alloy extruded profile, powder coated and provided

in fabric coordinated colour. The rolling tube should be made up of aluminium alloy from extruded profile of

Ø34mm. The fabric of this Blind should be made up of 100% anti-static polyester vanes having light filtering

M.R. and sheer vanes to reduce glare. Sheer layers made of white 100% knit polyester & the selection of colors, SQM 35.00 6,732.56 235,639.63

textures and opacities as per Engineer-in-charge. The FABRIC shall be constructed from spun-bonded 100%

polyester fiber, having Green guard Certification treated with soil & dust repellant require minimum regular

interval cleaning. The fabric has a maximum width of 2.80 M and a thickness of 0.38mm (+ 5%) and having

weight of 272g/m2 (+ 5%).The strip size is Solid 8.5 cm / Sheer 6 cm. The shading to be operated by Easy rise

mechanism with a continuous cord loop operating option. All plastic parts are in white color. Installation to

be done by quick release brackets (wall or ceiling).

ROLLER BLINDS - Providing & supplying of Window Blinds as per the approved sample in required shade and

style consisting, of Roller Blinds comprising of optima screen Fabric comprising of 22% polyester, 78% PVC,

Fabric weight 460-480G weight per sqm, Thickness 0.67 mm, Yarn count 18-19/cm, having fire resistance

standard – NFPA 701-89 small testing ISO-5659-2. The tear resistance should be complying to ISO4674 &

breaking resistance – ISO 5081. The DRIVE UNIT shall be of clutch for quick, easy and safe installation,

molded plastic with steel spring support and inserted into the tube end. It shall be driven by a ball chain

pulley with ball chain and can be positioned at right side or left-hand side of the Shade. The Shade when

lowering or raising, shall be automatically locked in position upon release of the ball chain by means of a

built-in friction lock. Universal clutch for left- and right-hand operation. Chain Gear Ratio of 1.75:1. The END

MR PLUG shall be molded of plastic with a steel location pin. The plug shall be inserted into the tube end. SQM 270.00 2,300.00 621,000.00

(Opposite to the Drive Unit) for ease of installation. The SUPPORT BRACKETS shall be of coated steel &

provided with covers and used in right hand or left-hand positions differentiated by the acceptance of the

of the rectangular drive unit support or the round idler plug pin. Can be installed (a) On Face (b) Ceiling

Mount (c) On Frame (d) in Recess. The Bracket should be protruding outside maximum of 80mm.The ROLLER

TUBE shall be of extruded aluminium with 37mm internal diameter & skin thickness of 1mm and shall

incorporate a keyway integral with the tube to accommodate the spline. The BOTTOM RAIL shall be a Flat

Bottom made up of powder coated steel. The BALLCHAIN shall be 2mm diameter cord with 4.5mm

diameter acetal balls molded co-axially to it on 6mm pitch to form an endless ball chain. It is used for raising

or lowering action of the shades.

Providing & fixing imported decorative Poly décor fabric Wall Paper (on walls and ceiling) of weight 475

7.5 MR g /sqm as per approved shade & design including prepration of surface with 2 coats of Nubin Glue based SQM 50.00 3,695.60 184,780.25

Providing & fixing custom printer, as per approved design, decorative Poly décor fabric Wall Paper (on walls

7.5 MR and ceiling) of weight 475 g /sqm as per approved shade & design including prepration of surface with 2 SQM 15.00 4,650.00 69,750.00

coats of Nubin Glue based epoxy quote.

Digitally signed by AMIT

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass surface with 15 yrs MCS warranty

as approval of the Architect. (Only film surface area shall be measured and paid).

Reception Table:-Providing & Installation of Reception table of of size upto 2.4m x 0.90m x 0.75m/ 1.2m (ht),

made out of 19mm thk. Commercial Board finished in Acrylic Solid Surface/ italian stone/ marble of

7.8 M.R. approved shade and colors complete as per design. One (1) number Drawer pedestal with 3 lockable Nos. 1.00 180,000.00 180,000.00

drawers and channels (all hardware from Hettich) to be provided under the table to be finished in Solid

Acrylic surface. All visible surfaces to be finished using Acrylic solid surface as per details.

Conference Table - Providing & Installation of Custom made 'U' shaped Board Room Table complete as per

design having straight/curved edges out of the overall size of upto length 10.0 m, ht . 0.75m, width 2.4 m, in

19mm thk. Commercial Board base finished in 1mm thick laminate as per design and shade. Table top to

be made in 19mm thick commercial board and finished in 6 mm thick acrylic solid surface of approved

pattern and shade having edge of 50-75mm thick tapered edge on all sides. Legs of the table to be upto

150mm x 150mm (Numbers as per design) made in 18mm thick commercial ply cladded in laminte to

match the table finish and hollow for taking the wires upto the table and a 19mm Thk Commercial board

Raceway (150 x 150 ) below table top to be provided for carriage of cables. All surfaces to be finished in

1mm thick laminte of approved shade and pattern. The cost to include making of cut outs necessary for

electricity pop up boxes. All veneer surfaces to be finsihed in PU polish.

Preparation of complete set of shop drawings including finishing, MEP services, details, design calcualtions

7.9 M.R. etc. and any other details as and when desired by Engineer In charge /client. A qualified professsional for 1.00% 93,432,387.50 934,323.87

the purpose shall be appointed after due appproval from Engineer In Charge.

Providing and fixing of 5-6 mm thick annealed GRIHA rated lacquered glass manufactured industrially by

curtain coating process with PU lacquer (50 micron thick), opaque (if viewed against a support wall)

conforming to EN 16477 standards for back painted glass , of approved color by Architect/ Client fixed with

compatible Silicone having Shear Bond Strength (Dry, 24 hours), greater than 450 kpa and tack free time of

10 to 30 mins compatible for installation of mirror and lacquered glass / Foam based double sided adhesive

tape for instantaneous adhesion, compatible with mirror and lacquered glass having Shear bond strength

7.10 M.R. (Dry, 15 mins) of 250 to 350 kpa) on a perfectly leveled 12mm thick water proof marine plywood / MDF / Nos. 30.00 3,877.64 116,329.10

Mineral fibre board which is mounted on the RCC wall/any other structure. The contractor should submit test

reports for backpainted glass from manufacturer - High humidity Resistance (conforms to BS EN 1036 1999);

Color fastness ISO 105B02 standard & Mechanical Resistance ISO 7784 ( Taber Abrasion test ) ISO 2409 (

Cross Hatch Test ) standard The manufactured backpainted glass should be environmentally friendly (no

lead, no arsenic, no copper, noformaldehyde); appropriate recycled content (12% post industrial / 6% post

consumer); compressive strenght (1000 MPa) & tensile strenght (40 MPa),same as float glass

Providing & fixing 12mm Thick. 100% Acrylic solid surface of approved make and colour using approved

Adhesive to 12 mm thk. Waterproof Plywood of approved brand as per shape, pattern & details given in the

drawing. The rate includes providing & fixing beading, cutting, scaffolding, nails, all materials, labour, lead,

lifts, HOM etc., complete.-for Lift Cladding. (The make, Shade, pattern etc., to be approved by Architect).

SUB TOTAL OF FINISHES 619,802.00 3,980,655.05

Digitally signed by AMIT

Interior Fit-Out Works in The Office Space of the MSTC at World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR FURNITURE

SL Item Item Description / Technical Specifications Total Qty Rate Total Reference Image

The overall size of Chair shall be height 1020 to 1120 +/-5 mm, width should be 595 +/-5mm and depth

should be 640 +/-5mm. Back Width 435 mm at Top and 490mm at bottom, Seat Width 500 +/-5 mm, Seat

Depth 465+/-5 mm and Seat height 450mm to 550 mm +/-5mm range. Seat should be made up of foam pre

moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be

upholstered with micro fabric 100% polyster 180 GSM abrasion > 50000 cycles. No flamming or progressive

smoldering within one hour of placement of the cigarettes. Fire rated fabric confirming to BS EN 1021 (match)

should be used. The chair shall be supplied with Mesh at the back rest. The back frame shall be made up of

Reception injection molded nylon GF 3. Adjustable Lumbar Support of size 300 mm lenght, 150 mm height and 3mm Reception

Chair thickness travel upto 65mm. The Chair should be provided with synchro mechanism with single lever with one &waiting area

position lock. The mechanism shall allow360 degree revolving feature along with height adjustablility one Way

with height adjustment button made of Delrin P 500 & arm top shall be PU material. The mechansim shall

possess seat to back recline ratio of 3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA

standards. Nylon Base to be provied. Twin castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X

5.1 2017 standards. The base shall be 660 mm PCD (26 inches) five pronged bases made up of PA6, 30%

glass filled reinforced with bottom ribbing for additional buttress and strength. The OEM shall have ISO 9001,

ISO 14001, BIFMA Level-2 and GreenGuard Certification.

The overall size of the chair shall be 690 width x 750 height and 580 mm depth. The seat height shall be

460mm. The understructure material of the chair shall be beachwood. The chair understructure shall have 4

legs that should be interconnected with each other. The seat & back shall be made up of insitu molded PU

Lounge Reception

2 foam having seat, back & side armrests entire connected. The entire seat shell shall be uphosterd with high 10.00 46,256.00 462,560.00

Chair &waiting area

quality polyester fabric. Wood shall be polished in desirable shade for better appearance. The lounge chair

shall be as per the reference image. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and

GreenGuard Certification.

Center table in size of 1200 W x 600 D x 550 H (mm)

Table top shall be 18mm thick Prelaminated particle board E1 norms and the Understructure shall be made

Center Reception

3 up of 19x19mm square MS pipe having thickness of 1.6 mm. Frame shall be welded by CO2 welding process 2.00 24,000.00 48,000.00

Table &waiting area

for uniform conforming to IS 816. Understructure frame shall be powder coated in black shade. The OEM shall

have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

Center table in size of 600 W x 600 D x 550 H (mm)

Table top shall be 18mm thick Prelaminated particle board E1 norms and the Understructure shall be made

Corner Reception

4 up of 19x19mm square MS pipe having 1.6mm thickness. Frame shall be welded by CO2 welding process for 2.00 22,000.00 44,000.00

Table &waiting area

uniform conforming to IS 816. Understructure frame shall be powder coated in black shade. The OEM shall

have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

MAIN TABLE WITH SIDE UNIT & BACK UNIT

Overall Size : W 2700 x D 1000 x H 750mm & Side Unit Extention: W 1400 x D 550 x H 750mm. Table Top:

25mm thick pre laminated particle board with 2mm PVC edge lipping supported on V Shape aluminium die

cast connectors of min size 430 mm L x 110 mm H x 25 mm Thick. 4 Connectors on Main table & 2 on side

unit shall be provided. All sides of the worktop except corners of main & side table shall be provided with

2mm thick alumimum extrusion of 40mm + 25 mm + 30 MM + 8 mm formed into horizontal & vertical

direction to enable support as well as top surface coverage. edge surface extrusion supporting the worktop to

be tappered towards top. Support: End Legs: 25mm thick pre laminated particle board with 2mm PVC edge

lipping & 3 equal drawer pedetal. Modesty Panel: 18mm thk pre lam board with 2mm PVC edge lipping of

450mm Ht. Wire Management: Slide Connect with PVC cable dump. Slide connect Configuration - Standard

5 CMD Table switch configuration no deviation 2 Power,2 USB Charger,1 Network,1 HDMI. Sufficient storage space to be CMD Room 1.00 276,915.33 276,915.33

priovided in the storage pedestal of the table having drawers at the main table & hinged door storage below

the side unit. The main and the return table top will have 10 mm thick Euro bronze glass with white vinyl film

hot laminated and Kuraray pvb interlayer. Back Unit Overall Size W 1500 x D 600 x H 750mm, Table Top:

25mm thick pre laminated particle board with 2mm PVC edge lipping sides covered with 2mm thick anodised

alumimum extrusion of same size as above supported on V Shape aluminium die cast connectors of same size

as above. Back: 25mm thick pre laminated particle board with 2mm PVC edge lipping with aluminium die cast

arms Shutters: 25mm thick pre laminated particle board with 2mm PVC edge lipping with brush steel handles

and softclose drawer slides and hinges. The back unit table top shall also have 10 mm thick Euro bronze glass

with white vinyl film hot laminated and Kuraray pvb interlayer. The OEM shall have ISO 9001, ISO 14001,

BIFMA Level-2 and GreenGuard Certification.

Digitally signed by AMIT

High back Chair having back height of 770 mm and width of 380 mm from top & 500 from mid (lumbar) level.

Seat Depth shall be 480 mm and seat width shall be 540 mm at front & 450 mm at back. Armrest to Armrest

distance of 680 mm. Seat height shall range between 410 mm to 470 mm. Armest shall be finished with foam

& leather on the user side & top with water fall edge to provide comfort to user & outside of armrests as well

as below back shall be finished with wooden texture. Below portion of armrest opening towards seat shall be

Main HB finished with crome surface. Knee tilt mechanism shall be provided having tilt tension adjustment & height

Chair adjustment at same level on right hand side of user & any position locking level at the left hand side of user.

Padded lumber support to be provided of height min. 200 mm. Back of the chair shall be finished with leather

upto height of 600 mm & wooden texture finish upto 200 mm & leather below the wooden texture. Aluminium

die cast pedestal having length of prongs 310 mm with 50 mm height towards centre & 25 mm height

outside. High Quality leather in beige or black to be suppiled. Twin wheel castors to be provided. The OEM

shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

Mid back Chair having back height of 610 mm and width of 380 mm from top & 500 from mid (lumbar) level.

Seat Depth shall be 480 mm and seat width shall be 540 mm at front & 450 mm at back. Armrest to Armrest

distance of 680 mm. Seat height shall range between 410 mm to 470 mm. Armest shall be finished with foam

& leather on the user side & top with water fall edge to provide comfort to user & outside of armrests as well

as below back shall be finished with wooden texture. Below portion of armrest opening towards seat shall be

Main MB finished with crome surface. Knee tilt mechanism shall be provided having tilt tension adjustment & height

Chair adjustment at same level on right hand side of user & any position locking level at the left hand side of user.

Padded lumber support to be provided of height min. 200 mm. Back of the chair shall be finished with leather

upto height of 440 mm & wooden texture finish upto 200 mm & leather below the wooden texture. Aluminium

die cast pedestal having length of prongs 310 mm with 50 mm height towards centre & 25 mm height

outside. High Quality leather in beige or black to be suppiled. Twin wheel castors to be provided. The OEM

shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

3 Seater Sofa in size of 2210 mm W x 1000 mm D x 880 mm H. The structure of the sofa shall be made up of

solid wood finished with melamine and the wood shall be extended upto the arms & visible outside the

armrest padding. The foam used in making this sofa shall be of density 32 and 40. Roll poly filling should be

8 used with this pu foam for giving extra comfort and softness to sofa. high quality nevar belts & good quality CMD Room 2.00 67,764.03 135,528.05

stapler pins to be used. The legs shall be made up of wood with melamine finish. The seat & back shall be

upholstered with high quality leatherite. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and

GreenGuard Certification.

1 Seater Sofa in size of 1000 mm W x 1000 mm D x 880 mm H. The structure of the sofa shall be made up of

solid wood finished with melamine and the wood shall be extended upto the arms & visible outside the

armrest padding. The foam used in making this sofa shall be of density 32 and 40. Roll poly filling should be

9 used with this pu foam for giving extra comfort and softness to sofa. high quality nevar belts & good quality CMD Room 1.00 30,571.97 30,571.97

stapler pins to be used. The legs shall be made up of wood with melamine finish. The seat & back shall be

upholstered with high quality leatherite. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and

GreenGuard Certification.

Table top -Table shall be made up of 18MM thick stained Rubber wood finish with veriner polish all sides.

Table top shall be in triangular shape with size of 720mm x 725mm x 350 H and 405L x 410D x 550H and

10 540L x 545D x 275H. understructure of the table. METAL LEGS - Table legs shall be made up of 19mm mild CMD Room 2.00 20,036.25 40,072.49

steel round tube with dully powder coated finish. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2

and GreenGuard Certification.

Meeting table in size of 3000 x 1200 x 750 (WDH)mm.

The worksurface of the table shall be made up of 25mm thick Pre-laminate particle board as per E1 norms

and its edges duly sealed with 2mm PVC Lipping on automatic machine at visible sides. Two Long sides of

the work surface shall be provided with reverse tapered edge design created by chamfering the board @ 45

degree inside for 17mm length & keeping 8mm straight & then edges sealed with 2mm thick PVC Lipping on

Meeting automatic machine. Leg: shall be made up of high pressure aluminum die casted 20 degree tapered, number

Table “7” shape & oblong cross section of about 55mm on top, 45mm at bottom and of 725mm length to get

750mm table height, it shall acts as vertical structural support member, connected by a horizontal cross

beams 50x25x1.6thk (16g) ERW tube & connected to the Aluminium diecast vertical legs through a high

pressure Aluminium diecast 90deg – 02 way connectors. Wire Management: 450mm Aluminium Flip Up and

provision to mount swicthes and sockets on PVC cable dump and Vertical wire entry cover made up of steel

sheets. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

Digitally signed by AMIT

High Back Chair with Headrest

The overall size of Chair shall be height 1225 to 1345 +/-5 mm, Back Width 495 mm at Top and 385mm at

bottom, Seat Width 500 +/-5 mm, Seat Depth 390 to 450 +/-5 mm and Seat height 480mm to 600 mm +/-

5mm range. And over all chair width should be 690 +/-5mm and Overall chair depth should be 630 to 690 +/-

5mm. Seat should be made up of foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50%

deflection conforming to IS 3400. Seat shall be upholstered with Polyester & viscose- 380 GLM, Abrasion- > CMD Room -

12 45000 cycles. The chair shall be supplied with Lenear Mesh at the back & shall be provided With 290mm Meeting 1.00 41,382.02 41,382.02

width, 180mm height Headrest. Adjustable Lumbar Support full length of size 325 mm , 105 mm height and Room

3mm thickness in contoured form can travel upto 30mm at the back .Four Way Adjustable Arms to be

provied with height adjustment button made of Delrin P 500. The mechansim shall possess seat to back

recline ratio of 3:7. Nylon Base to be provied. Twin castors 60 mm dia with PA6 material complying to ANSI/

BIFMA X 5.1 2017 standards. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard

Mid Back Chair :The overall size of Chair shall be height 1050 to 1170 +/-5 mm, Back Width 495 mm at Top

and 385mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 390 to 450 +/-5 mm and Seat height 480mm

to 600 mm +/-5mm range. And over all chair width should be 690 +/-5mm and Overall chair depth should be

630 to 690 +/-5mm. Seat should be made up of foam pre moulded at 55 kg/m3 density. hardness of 25+

3kgf at 50% deflection conforming to IS 3400. Seat shall be upholstered with Polyester & viscose- 380 GLM,

Mid Back Abrasion- > 45000 cycles. The chair shall be supplied with Lenear Mesh at the back rest. Adjustable Lumbar

Chair Support full length of size 325 mm , 105 mm height and 3mm thickness in contoured form can travel upto

30mm at the back .The Chair should be provided with Synchro tilt Mechanism – with three Multi lock

features. Four Way Adjustable Arms to be provied with height adjustment button made of Delrin P 500. The

mechansim shall possess seat to back recline ratio of 3:7. Nylon Base to be provied. Twin castors 60 mm dia

with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. The OEM shall have ISO 9001, ISO

14001, BIFMA Level-2 and GreenGuard Certification.

The overall size of the is 1980 L x 900 x 450/750. The head rest, foot rest and side panels shall be made up

of from 18mm thk prelaminated particle board of 18mm thk with 2mm PVC edge banding. The design shall

offers ample storage space to keep stuffs like trolleys, luggage bags, suitcases and many more things and to

take out these stuffs, the product shall be provided with a bed lifter arrangement that opens-up upto 30

14 Single Bed CMD Room 1.00 18,584.00 18,584.00

degrees enables to take out the stored items / lugguages etc. quickly & easily. It shall be supplied in a

knockdown (KD) design, easy to install, strong and robust product. The metal parts shall be powder coating

finish of 60-80 microns thick. The hardware shall be of steel, comes with zinc blue / yellow / black

passivation. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

The overall size shall be 900 x 450 x 1800 (WDH) mm. Top shall be made up of 18mm thick pre laminated

particle board and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge

lipping, Shutters shall be made up of 18 mm thick pre laminated particle board. 4 Shutters to be provied for

15 Wardrobe CMD Room 1.00 34,648.06 34,648.06

uper & lower compartment. Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. Hanger rod

also provided for hanging clothes. The wardrobe shall have two shelves, two drawers with lock and one

hanging area. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

The overall size of discussion table in Dia. 900mm X 750mm H that is to be assembled at site. The table top

shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate

and finish as per approved shade. The table top profile shall be in circular shape and the edges shall be

sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted

VIP waiting with the assistance of edge banding machine Leg: shall be made up of high pressure aluminum die casted 20

room degree tapered, number “7” shape & oblong cross section of about 55mm on top, 45mm at bottom and of

725mm length to get 750mm table height, it acts as vertical structural support member, connected by a

horizontal cross beams 50x25x1.6thk (16g) ERW tube & connected to the Aluminium diecast vertical legs

through a high pressure Aluminium diecast connectors. The OEM shall have ISO 9001, ISO 14001, BIFMA

Level-2 and GreenGuard Certification.

The overall size of the chair shall be 690 width x 750 height and 580 mm depth. The seat height shall be

460mm. The chair understructure shall have 4 legs that should be interconnected with each other through

frame. The understructure of the chair shall be made from solid wood i.e properly treated & seasoned kiln

dried beach wood, finished with clear synthetic PU coating for the best resilence and high durability. The legs

and the frame shall be joined together by method of tenon and mortise for durability and better aesthetics.

VIP waiting Four legs shall be provided and the cross section of leg at the bottom shall be 35x35 and top shall be 55x35

room provided in tappered finish for better looks. The outer side of the legs shall be rounded & inner side shall be

corner edges. The wooden frame shall be of size 55mm x 22mm thick with visible face of 55 mm front and

22mm shall be below the seat. The seat & back shall be made up of insitu molded PU foam having seat, back

& side armrests entire connected. The entire seat shell shall be uphosterd with high quality polyester fabric.

Wood shall be polished in desirable shade for better appearance. The OEM shall have ISO 9001, ISO 14001,

BIFMA Level-2 and GreenGuard Certification.

Digitally signed by AMIT

The overall size of Height Adjustable shall be 1500 x 750 x 740 (WDH)mm. The worktop shall be made up of

25mm thick pre-laminated particle board of E1 norms. The modesty panel shall be of 18mm thick PLPB E1

norms. Support End Legs: MS powder coated motorised height adjustable under structure shall be provided

with height varying from 600-1200mm. Wire Management: 450mm Alumninium flip up and provision to

mount swicthes and sockets on PVC cable dump & vertebra for wire uptake from MS cable tray fixed below

the under structure and wire entry cover for wire intake from floor to cable tray. Electric Adjustament

18 Adjustable CMD Room 0.00 58,905.32 0.00

Features:- Operation shall be through DC voltage motorized leg columns managed by an electrical control box

situated under the work surface. Height adjustment shall be controlled by a switch located under or

integrated to the front of the work surface on either the left or right hand of the desk. The mechanism shall

cut out automatically when the desk reaches the top or bottom of its range, or when the control button is

released. Leg Lifting Load Capacity 140Kgs UDL shall be provided. The OEM shall have ISO 9001, ISO 14001,

BIFMA Level-2 and GreenGuard Certification.

The overall size of the Recliner shall be 850 mm width x 1050 mm height & depth 895mm and 1575mm when

reclined. Height of the armrest from the ground level shall be 600 mm. overall width of the armrests including

top flap shall be 130 mm. The recliner shall electrically operated and handheld remote shall be provided along

with the recliner attached with flexible wire. The user shall be able to recline fully with the help of remote and

19 Ante Room the foot resting flap shall automatically come out from below to expand the body to give comfort. The recliner CMD Room 1.00 79,366.00 79,366.00

shall also have the lifting feature within remote to push the body from back & enable the user to get up from

the recliner easily if required. The user touch surface of the recliner shall be upholstered with Pure Leather

and the other one shall be in matching leatherite. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2

and GreenGuard Certification.

The overall size of discussion table in Dia. 900mm X 750mm H that is to be assembled at site. The table top

shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate

and finish as per approved shade. The table top profile shall be in circular shape and the edges shall be

sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted

VIP waiting with the assistance of edge banding machine Leg: shall be made up of high pressure aluminum die casted 20

room degree tapered, number “7” shape & oblong cross section of about 55mm on top, 45mm at bottom and of

725mm length to get 750mm table height, it acts as vertical structural support member, connected by a

horizontal cross beams 50x25x1.6thk (16g) ERW tube & connected to the Aluminium diecast vertical legs

through a high pressure Aluminium diecast connectors. The OEM shall have ISO 9001, ISO 14001, BIFMA

Level-2 and GreenGuard Certification.

Cabin Table in size of 2400W X 900D X 750H, Side unit of 1050W X 450D X 750H with Back storage -2700W

X 450D X 1200H. Table Top: 25mm thick Pre laminate particle board E1 norms with 2mm PVC edge lipping on

all exposed edges. Two Long sides of the work surface shall be provided with reverse tapered edge design

created by chamfering the board @ 45 degree inside for 17mm length & keeping 8mm straight & then edges

sealed with 2mm thick PVC Lipping on automatic machine Leg: shall be made up of high pressure aluminum

die casted 20 degree tapered, number “7” shape & oblong cross section of about 55mm on top, 45mm at

bottom and of 725mm length to get 750mm table height, it acts as vertical structural support member,

connected by a horizontal cross beams 50x25x1.6thk (16g) ERW tube & connected to the Aluminium diecast

vertical legs through a high pressure Aluminium diecast 90deg – 02 way connectors. The connector should

have “V” / “U” shape tapered groove for sliding a Aluminium diecast slider nut. The slider nut shall be an

21 with side Corner Cabin 4.00 145,709.00 582,836.00

Aluminium diecast part that has same taper as of “V” / “U” shape in the diecast connector. Modesty Panel:

18mm thk pre lam board with 2mm PVC edge lipping of 450mm Ht. Wire Management: 450mm Aluminium

Flip Up and provision to mount swicthes and sockets on PVC cable dump and Vertical wire entry cover. Cross

Beam: Leg to Leg shall be connected using cross beams made from 50x25x1.60mm (16g) Rectangular tube

and to give floating look & to connect the table top with cross beams injection moulded polycarbonate

spacers should be used of dia 61mm x 42.50mm H insert moulded with M6x1P zinc blue plated bolt of 22mm

L.Spacer height including bolt should be 64.50mm. Side Composite Storage (Openable Shutter +3D+1F) Top

& Sides : 18mm Thk pre laminated particle board Back E1 norms: 9mm Thk pre laminated particle board

Shutters : 18mm Thk pre laminated particle board Handle : Finger groove handle Lock. The OEM shall have

ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

High Back Chair (Mesh)

The overall size of Chair shall be : Width should be 615 +/-5mm and depth should be 640 +/-5mm. Total

height 1160 to 1260 +/-5 mm, Back Width 480 mm at Top and 420mm at bottom, Seat Width 500 +/-5 mm,

Seat Depth 465+/-5 mm and Seat height 460mm to 560 mm +/-5mm range. Seat should be made up of

foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat

shall be upholstered with micro fabric 100% polyster 180 GSM abrasion > 50000 cycles. No flamming or

progressive smoldering within one hour of placement of the cigarettes. Fire rated fabric confirming to BS EN

1021 (match) should be used. The chair shall be supplied with Dynaflex Two Piece Back Construction with

22 IS20D Mesh upholstred. Back shall be provided With 260mm width, 160mm height and 50mm height Corner Cabin 4.00 26,009.34 104,037.35

adjastable Headrest. The Chair should be provided with Synchro tilt Mechanism 3 Multi lock features. The

mechanism shall allow revolving feature with height adjustablility. One Way Adjustable Arms (Height) to be

provied with height adjustment button made of Delrin P 500. The mechansim shall possess seat to back

recline ratio of 3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Nylon Base to be

provied. Twin castors 60 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. the axle

pin shall be rust protected zinc passivated. The base shall be 660 mm PCD (26 inches) five pronged bases

made up of PA6, 30% glass filled reinforced with bottom ribbing for additional buttress and strength. The

OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

Digitally signed by AMIT

Mid Back Chair (Mesh)

The overall size of Chair shall be : Width should be 615 +/-5mm and depth should be 640 +/-5mm. Total

height 1050 to 1150 +/-5 mm, Back Width 480 mm at Top and 420mm at bottom, Seat Width 500 +/-5 mm,

Seat Depth 465+/-5 mm and Seat height 460mm to 560 mm +/-5mm range. Seat should be made up of

foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat

shall be upholstered with micro fabric 100% polyster 180 GSM abrasion > 50000 cycles. No flamming or

progressive smoldering within one hour of placement of the cigarettes. Fire rated fabric confirming to BS EN

1021 (match) should be used. The chair shall be supplied with Dynaflex Two Piece Back Construction with

23 revolving Corner Cabin 12.00 19,740.00 236,880.00

IS20D Mesh upholstred. The Chair should be provided with Synchro tilt Mechanism – with three Multi lock

features. The mechanism shall allow revolving feature with height adjustablility. One Way Adjustable Arms

(Height) to be provied with height adjustment button made of Delrin P 500. The mechansim shall possess

seat to back recline ratio of 3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Nylon

Base to be provied. Twin castors 60 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017

standards. the axle pin shall be rust protected zinc passivated. The base shall be 660 mm PCD (26 inches)

five pronged bases made up of PA6, 30% glass filled reinforced with bottom ribbing for additional buttress

and strength. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

3 Seater Sofa : Overall size shall be 2020 mm W x 975 mm D x 820 mm H. Sofa inner frame structure shall

be made from the combination of treated solid wood and plywood having high quality webbing belts to ensure

good strength, rigidity & stable construction to offer high durability. There shall be extra padding between the

armrest & the seat on both sides for better comfort & polyfilled in arms & backrest. The polyurethane (PU)

3 seater foam shall be used in Seat & back rest having 40 density and 32 density respectively. Seat to backrest angle

sofa should be ergonomically designed to offer the best seating comfort. Seat height shall be normally between 16

to 18 inches and depth shall be between 20-22 inches. Sofa shall be elevated from ground by about 3 inches

using Gold finished metal legs creating provision for easy cleaning & better look. Upholstery shall be of high

quality Leatherite offer the best feel & comfort. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and

GreenGuard Certification.

2 Seater Sofa : Overall size shall be 1610 mm W x 975 mm D x 820 mm H. Sofa inner frame structure shall

be made from the combination of treated solid wood and plywood having high quality webbing belts to ensure

good strength, rigidity & stable construction to offer high durability. There shall be extra padding between the

armrest & the seat on both sides for better comfort & polyfilled in arms & backrest. The polyurethane (PU)

2 seater foam shall be used in Seat & back rest having 40 density and 32 density respectively. Seat to backrest angle Corner Cabin

sofa should be ergonomically designed to offer the best seating comfort. Seat height shall be normally between 16

to 18 inches and depth shall be between 20-22 inches. Sofa shall be elevated from ground by about 3 inches

using Gold finished metal legs creating provision for easy cleaning & better look. Upholstery shall be of high

quality Leatherite offer the best feel & comfort. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and

GreenGuard Certification.

1 Seater Sofa : Overall size shall be 980 mm W x 975 mm D x 820 mm H. . Sofa inner frame structure shall

be made from the combination of treated solid wood and plywood having high quality webbing belts to ensure

good strength, rigidity & stable construction to offer high durability. There shall be extra padding between the

armrest & the seat on both sides for better comfort & polyfilled in arms & backrest. The polyurethane (PU)

1 seater foam shall be used in Seat & back rest having 40 density and 32 density respectively. Seat to backrest angle Corner Cabin

sofa should be ergonomically designed to offer the best seating comfort. Seat height shall be normally between 16

to 18 inches and depth shall be between 20-22 inches. Sofa shall be elevated from ground by about 3 inches

using Gold finished metal legs creating provision for easy cleaning & better look. Upholstery shall be of high

quality Leatherite offer the best feel & comfort. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and

GreenGuard Certification.

The overall size of the table shall be 1050 L x 525 D x 450 H mm. The top surface of the table shall be in boat

shape design having maximum size at the middle & lesser at the ends to form this unique shape. The table

top shall be made up of 18mm thick Prelaminated particle board of E1 norms. The edges shall be sealed

properly with 2mm thick PVC edge banding on automatic machine. The understructure of the table shall be

made from solid wood i.e properly treated & seasoned kiln dried beach wood, finished with clear synthetic PU

Center coating for the best resilence and high durability. The legs and the frame shall be joined together by method

Table of tenon and mortise for durability and better aesthetics. Four legs shall be provided and the cross section of

leg at the bottom shall be 35x35 and top shall be 55x35 provided in tappered finish for better looks. The

outer side of the legs shall be rounded & inner side shall be corner edges. The wooden frame shall be of size

55mm x 22mm thick with visible face of 55 mm front and 22mm shall be below the table top running at all

four ends as well as one support in the middle. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and

GreenGuard Certification.

Digitally signed by AMIT

The overall size of the Recliner shall be 850 mm width x 1050 mm height & depth 895mm and 1575mm when

reclined. Height of the armrest from the ground level shall be 600 mm. overall width of the armrests including

top flap shall be 130 mm. The recliner shall electrically operated and handheld remote shall be provided along

with the recliner attached with flexible wire. The user shall be able to recline fully with the help of remote and

28 Ante Room the foot resting flap shall automatically come out from below to expand the body to give comfort. The recliner Corner Cabin 3.00 79,366.00 238,098.01

shall also have the lifting feature within remote to push the body from back & enable the user to get up from

the recliner easily if required. The user touch surface of the recliner shall be upholstered with Pure Leather

and the other one shall be in matching leatherite. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2

and GreenGuard Certification.

The overall size of discussion table in Dia. 900mm X 750mm H that is to be assembled at site. The table top

shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate

and finish as per approved shade. The table top profile shall be in circular shape and the edges shall be

sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted

VIP waiting with the assistance of edge banding machine Leg: shall be made up of high pressure aluminum die casted 20

room degree tapered, number “7” shape & oblong cross section of about 55mm on top, 45mm at bottom and of

725mm length to get 750mm table height, it acts as vertical structural support member, connected by a

horizontal cross beams 50x25x1.6thk (16g) ERW tube & connected to the Aluminium diecast vertical legs

through a high pressure Aluminium diecast connectors. The OEM shall have ISO 9001, ISO 14001, BIFMA

Level-2 and GreenGuard Certification.

The overall size of the is 1980 L x 900 x 450/750. The head rest, foot rest and side panels shall be made up

of from 18mm thk prelaminated particle board of 18mm thk with 2mm PVC edge banding. The design shall

offers ample storage space to keep stuffs like trolleys, luggage bags, suitcases and many more things and to

take out these stuffs, the product shall be provided with a bed lifter arrangement that opens-up upto 30

30 Single Bed CMD Room 3.00 18,584.00 55,752.00

degrees enables to take out the stored items / lugguages etc. quickly & easily. It shall be supplied in a

knockdown (KD) design, easy to install, strong and robust product. The metal parts shall be powder coating

finish of 60-80 microns thick. The hardware shall be of steel, comes with zinc blue / yellow / black

passivation. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

Office Main Table shall be of size 1500L x 750D x 750 H with side unit of 900 x 450 x 740 (WDH) mm. The

worksurface of the table shall be made up of 25mm thick Pre-laminate particle board as per E1 norms and its

edges duly sealed with 2mm PVC Lipping on automatic machine at visible sides. Understructure shall be

supported on CRCA MS powder coated angular legs of cross section 40 x 40 x 1.6mm thick and cross beam

made up of 40 x 20 x 1.2 mm thick. vertical Legs shall be connected with horizontal beam through aluminium

die cast connectors having opening of 40 x 40 on the vertical side & 40 x 20 on the horizontal side to

accomodate connetion of Leg & horizontal frame. Pedestal Top & Sides shall be made up of 18mm thk pre Corner Cabin -

laminated particle board E1 norms, Back : 9mm Thk pre laminated particle board. Pedestal - 2D+1F with PA/PS

Cylindricle lock in Size : 400W X 450D X 600Ht. Top & Sides: 18mm Thk pre laminated particle board . Back:

9mm Thk pre laminated particle board. Edge: All exposed area with 2mm thick PVC edge lipping The drawers

front & filling shall be provided with sleek finger groove handle less design for a streamlined look. Finger

groove shall be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered

towards inside @ 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. The

OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

The overall size of Chair shall be height 1020 to 1120 +/-5 mm, width should be 595 +/-5mm and depth

should be 640 +/-5mm. Back Width 435 mm at Top and 490mm at bottom, Seat Width 500 +/-5 mm, Seat

Depth 465+/-5 mm and Seat height 450mm to 550 mm +/-5mm range. Seat should be made up of foam pre

moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be

upholstered with micro fabric 100% polyster 180 GSM abrasion > 50000 cycles. No flamming or progressive

smoldering within one hour of placement of the cigarettes. Fire rated fabric confirming to BS EN 1021 (match)

should be used. The chair shall be supplied with Mesh at the back rest. The back frame shall be made up of

Mid Back injection molded nylon GF 3. Adjustable Lumbar Support of size 300 mm lenght, 150 mm height and 3mm Corner Cabin -

chair thickness travel upto 65mm. The Chair should be provided with synchro mechanism with single lever with one PA/PS

position lock. The mechanism shall allow360 degree revolving feature along with height adjustablility one Way

with height adjustment button made of Delrin P 500 & arm top shall be PU material. The mechansim shall

possess seat to back recline ratio of 3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA

standards. Nylon Base to be provied. Twin castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X

5.1 2017 standards. The base shall be 660 mm PCD (26 inches) five pronged bases made up of PA6, 30%

glass filled reinforced with bottom ribbing for additional buttress and strength. The OEM shall have ISO 9001,

ISO 14001, BIFMA Level-2 and GreenGuard Certification.

2 Seater Sofa : Overall size shall be 1610 mm W x 975 mm D x 820 mm H. Sofa inner frame structure shall

be made from the combination of treated solid wood and plywood having high quality webbing belts to ensure

good strength, rigidity & stable construction to offer high durability. There shall be extra padding between the

armrest & the seat on both sides for better comfort & polyfilled in arms & backrest. The polyurethane (PU)

2 seater foam shall be used in Seat & back rest having 40 density and 32 density respectively. Seat to backrest angle Corner Cabin -

sofa should be ergonomically designed to offer the best seating comfort. Seat height shall be normally between 16 PA/PS

to 18 inches and depth shall be between 20-22 inches. Sofa shall be elevated from ground by about 3 inches

using Gold finished metal legs creating provision for easy cleaning & better look. Upholstery shall be of high

quality Leatherite offer the best feel & comfort. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and

GreenGuard Certification.

Digitally signed by AMIT

The overall size of the table shall be 1050 L x 525 D x 450 H mm. The top surface of the table shall be in boat

shape design having maximum size at the middle & lesser at the ends to form this unique shape. The table

top shall be made up of 18mm thick Prelaminated particle board of E1 norms. The edges shall be sealed

properly with 2mm thick PVC edge banding on automatic machine. The understructure of the table shall be

made from solid wood i.e properly treated & seasoned kiln dried beach wood, finished with clear synthetic PU

Center coating for the best resilence and high durability. The legs and the frame shall be joined together by method

Table of tenon and mortise for durability and better aesthetics. Four legs shall be provided and the cross section of

leg at the bottom shall be 35x35 and top shall be 55x35 provided in tappered finish for better looks. The

outer side of the legs shall be rounded & inner side shall be corner edges. The wooden frame shall be of size

55mm x 22mm thick with visible face of 55 mm front and 22mm shall be below the table top running at all

four ends as well as one support in the middle. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and

GreenGuard Certification.

Exectuive Table of size 2250 x 900 x740 (WDH) main table with side unit height adjustable in size of 1050 x

450 x 750(WDH)mm and back unit 2100 x 450 x 740 (WDH)mm. Overhead storage in size of 2400 x 300x

450 (WDH)mm. The worktop shall be made up of 25mm thick PLPB, Modesty Panel shall be 18mm thick PLPB

both E1 norms duly finished with 2mm pvc edge band. Modesty shall be connected with 3 nos L-shape

pressure aluminium die casted connector of 50 mm width. The understucture shall be made up of Loop leg of

CRCA Pipe having cross section of 55mm x 12mm x 61mm x 12mm x 55mm x 1.6 mm. The front modesty &

side modesty shall be made up of CRCA sheet 0.8mm perforated and powder coated finished. Horizontal

cross beams under table top that shall be connected to all 4 vertical legs through pressure die cast aluminium

connector. Side table : It shall include a fixed top and one height adjustable additional worktop made up of

18mm thick Particle board E1 norms operated through gas lift mechanism through user friendly lever Officer Cabin

provided in front below the adjustable top. The height adjustable top shall enable user work while standing Type-1

position whenever required to avoid excessive sitting. The side table shall have shelves and front to be

covered with shutters provided with lock & key mechanism for safety of documents. Storage Top shall be:

18mm Thk pre laminated particle board, Back shall be : 9mm Thk pre laminated particle board with 2mm PVC

edge lipping, Shutters: 18mm Thk pre laminated particle board. Edge: All exposed area with 2mm thick PVC

edge lipping. Accessories : Cut out through CNC Routed Machine and a Cable Dump tray with PVC/CRCA

material shall be mounted to hold switch and socket, Entire cable Dump tray shall be covered with Aluminum

extruded with injection moulded plastic side cover Flip up top to access switch and socket. Cable Vertebra of

PVC shall be provided to enable wire management from floor to tabletop surface. The OEM shall have ISO

9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

Exectuive Table of size 2100 x 900 x740 (WDH) main table with side unit height adjustable in size of 1050 x

450 x 750(WDH)mm and back unit 2100 x 450 x 740 (WDH)mm. Overhead storage in size of 2400 x 300x

450 (WDH)mm. The worktop shall be made up of 25mm thick PLPB, Modesty Panel shall be 18mm thick PLPB

both E1 norms duly finished with 2mm pvc edge band. Modesty shall be connected with 3 nos L-shape

pressure aluminium die casted connector of 50 mm width. The understucture shall be made up of Loop leg of

CRCA Pipe having cross section of 55mm x 12mm x 61mm x 12mm x 55mm x 1.6 mm. The front modesty &

side modesty shall be made up of CRCA sheet 0.8mm perforated and powder coated finished. Horizontal

cross beams under table top that shall be connected to all 4 vertical legs through pressure die cast aluminium

connector. Side table : It shall include a fixed top and one height adjustable additional worktop made up of

Cabin Main Officer Cabin

18mm thick Particle board E1 norms operated through gas lift mechanism through user friendly lever

provided in front below the adjustable top. The height adjustable top shall enable user work while standing

side+Back Cabin

position whenever required to avoid excessive sitting. The side table shall have shelves and front to be

covered with shutters provided with lock & key mechanism for safety of documents. Storage Top shall be:

18mm Thk pre laminated particle board, Back shall be : 9mm Thk pre laminated particle board with 2mm PVC

edge lipping, Shutters: 18mm Thk pre laminated particle board. Edge: All exposed area with 2mm thick PVC

edge lipping. Accessories : Cut out through CNC Routed Machine and a Cable Dump tray with PVC/CRCA

material shall be mounted to hold switch and socket, Entire cable Dump tray shall be covered with Aluminum

extruded with injection moulded plastic side cover Flip up top to access switch and socket. Cable Vertebra of

PVC shall be provided to enable wire management from floor to tabletop surface. The OEM shall have ISO

9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

The overall size of Chair shall be : width 600 +/-5mm, depth 640 +/-5mm. Total height 1170 to 1270 +/-5

mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-5 mm

and Seat height 470mm to 570 mm +/-5mm range. Seat made up of foam pre moulded at 55 kg/m3 density.

hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric

100% polyster 180 GSM abrasion > 50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should

be used. The chair shall be supplied with Mesh Back rest. The back frame shall be made up of Injection

Main HB molded PPGF 20% in light grey shade, armest support also in light grey shade. PU Adjustable Lumbar Officer Cabin

Chair Support full length of size 365 mm, 110 mm height and 25mm thickness. The Chair should be provided with Type-1

Self Calibrating Multilock Mechanism (Bio Snchyro mechansim) that should adjust the tension of the back

sensing weight of the user. The mechanism shall allow 360 degree revolving feature along with height

adjustablility. One Way Adjustable Arms (Height) to be provied with height adjustment button made of Delrin

P 500. The mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be class 4 tested

as per ANSI BIFMA standards. Metal base shall be provided of light grey color matching the chair back &

armrest. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

Digitally signed by AMIT

The overall size of Chair shall be height 915 to 1015 +/-5 mm, Back Width 415 mm at Top and 450mm at

bottom, Seat Width 480 +/-5 mm, Seat Depth 440+/-5 mm and Seat height 460mm to 560 mm +/-5mm

range. over all chair width should be 560 +/-5mm and Overall chair depth should be 670 +/-5mm. Seat

should be made up of foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection

conforming to IS 3400. Seat shall be upholstered with micro fabric 100% polyster 180 GSM abrasion > 50000

cycles. No flamming or progressive smoldering within one hour of placement of the cigarettes. Fire rated

fabric confirming to BS EN 1021 (match) should be used. The back frame shall be made up of PPGF and the

injection molded in grey color, armrest also in grey color. The chair shall be supplied with Mesh Back rest. The Officer Cabin

Chair should be provided with center tilt two position lock Mechanism. The mechanism shall allow 360 degree Type-1

revolving feature along with height adjustablility. Fixed arms connected to seat and back in the same contour.

The mechansim shall possess seat to back recline ratio of 1:1. The Gas Lift used shall be class 4 tested as per

ANSI BIFMA standards. Nylon Base in grey color to be provied. Twin castors 50 mm dia with PA6 material

complying to ANSI/ BIFMA X 5.1 2017 standards. the axle pin shall be rust protected zinc passivated. The

base shall be 660 mm PCD (26 inches) five pronged bases made up of PA6, 30% glass filled reinforced with

bottom ribbing for additional buttress and strength. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2

and GreenGuard Certification.

3 Seater Sofa in size of 1830 mm W x 750 mm D x 685 mm H. The structure of the sofa shall be made up of

solid wood and ply. The foam used in making this sofa shall be of density 32 and 40. Roll poly filling should be

3 seater used with this pu foam for giving extra comfort and softness to sofa. high quality nevar belts & good quality Officer Cabin

sofa stapler pins to be used. The legs and frame shall be made up of mild steel material duly polished in chrome Type-1

finish. The seat & back upholstery shalll have checkered design stiching for better aesthetics. The OEM shall

have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

The overall size of the table shall be 1050 L x 525 D x 450 H mm. The top surface of the table shall be in boat

shape design having maximum size at the middle & lesser at the ends to form this unique shape. The table

top shall be made up of 18mm thick Prelaminated particle board of E1 norms. The edges shall be sealed

properly with 2mm thick PVC edge banding on automatic machine. The understructure of the table shall be

made from solid wood i.e properly treated & seasoned kiln dried beach wood, finished with clear synthetic PU

Center coating for the best resilence and high durability. The legs and the frame shall be joined together by method

Table of tenon and mortise for durability and better aesthetics. Four legs shall be provided and the cross section of

leg at the bottom shall be 35x35 and top shall be 55x35 provided in tappered finish for better looks. The

outer side of the legs shall be rounded & inner side shall be corner edges. The wooden frame shall be of size

55mm x 22mm thick with visible face of 55 mm front and 22mm shall be below the table top running at all

four ends as well as one support in the middle. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and

GreenGuard Certification.

The overall size of the table shall be 1800 mm W x 800 mm D x 780 mm H. Overhead storage in size of 2400

x 300x 450 (WDH)mm. The table top shall be made up of prelaminated Particle board having total thickness

of 50mm having melamine finish on the top.The modesty and side panels shall be made up of particle board

16mm thick. The overall size of the side table shall be 1010 mm W x 500 mm D x 650 mm H. The thickness

Officer of the table top shall be 50mm. The side table design should be such that it has flexibility to be fixed either in

Cabin Main right hand side or left hand side of the user during the time of assembly. Side table shall have storage facility

40 Table with to keep documents designed in the form of higned door cabinet. side table shall have flapper to pass on 12.00 131,564.97 1,578,779.68

side + Back wires. The main table top & side table top shall be provided with aluminium extrusion strip below for

unit aesthetics. Back Storage shall be in size of 1800 x 450 x 740 (WDH)mm and Over Head unit size shall be

2250x 300 x 450 (WDH)mm. Design shall be Contemporary Top shall be: 18mm Thk pre laminated particle

board, Back shall be : 9mm Thk pre laminated particle board with 2mm PVC edge lipping, Shutters: 18mm

Thk pre laminated particle board. Edge: All exposed area with 2mm thick PVC edge lipping. The OEM shall

have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

The overall size of Chair shall be : Total height 1145 to 1245 +/-5 mm, Back Width 400 mm at Top and

435mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 455+/-5 mm and Seat height 455mm to 555 mm

+/-5mm range. And over all chair width should be 670 +/-5mm and Overall chair depth should be 670 +/-

5mm. Seat should be made up of foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50%

deflection conforming to IS 3400. Seat shall be upholstered with 100% polyster fabric 325 GSM abrasion >

50000 cycles. No flamming or progressive smoldering within one hour of placement of the cigarettes. Fire

rated fabric confirming to BS EN 1021 (match) should be used. The chair shall be supplied with Nylon mixed

High Back polyster Mesh at the back & shall be provided With 295mm width, 155mm height fixed head rest. Adjustable

Chair for Lumbar Support full length of size 365 mm , 80 mm height and 4mm thickness in contoured form can travel

41 Officer upto 80mm at the back. The Chair should be provided with synchro mechanism with single lever with Three 12.00 23,217.18 278,606.15

Cabine Type-position lock . The mechanism shall allow 360 degree revolving feature along with height adjustablility. The

2 mechanism shall allow 360 degree revolving feature along with height adjustablility. One Way Adjustable

Arms (Height) to be provied with height adjustment button made of Delrin P 500. The mechansim shall

possess seat to back recline ratio of 3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA

standards. Nylon Base to be provied. Twin castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X

5.1 2017 standards. the axle pin shall be rust protected zinc passivated. The base shall be 660 mm PCD (26

inches) five pronged bases made up of PA6, 30% glass filled reinforced with bottom ribbing for additional

buttress and strength. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard

Digitally signed by AMIT

The overall size of Chair shall be : Total height 965 to 1065 +/-5 mm, Back Width 400 mm at Top and

435mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 455+/-5 mm and Seat height 455mm to 555 mm

+/-5mm range. And over all chair width should be 670 +/-5mm and Overall chair depth should be 670 +/-

5mm. Seat should be made up of foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50%

deflection conforming to IS 3400. Seat shall be upholstered with 100% polyster fabric 300 GSM abrasion >

50000 cycles. No flamming or progressive smoldering within one hour of placement of the cigarettes. Fire

rated fabric confirming to BS EN 1021 (match) should be used. The chair shall be supplied with Nylon mixed

polyster Mesh at the back. Adjustable Lumbar Support full length of size 365 mm , 80 mm height and 4mm Officer Cabin

thickness in contoured form can travel upto 80mm at the back. The Chair should be provided with synchro Type-2

mechanism with single lever with Three position lock . . One Way Adjustable Arms (Height) to be provied with

height adjustment button made of Delrin P 500. The mechansim shall possess seat to back recline ratio of

3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Nylon Base to be provied. Twin

castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. the axle pin shall be

rust protected zinc passivated. The base shall be 660 mm PCD (26 inches) five pronged bases made up of

PA6, 30% glass filled reinforced with bottom ribbing for additional buttress and strength. Item to be 360

degree revolving and height adjustable with castor wheels.

High Back Chair in Leatherite

The overall size of Chair shall be : Total height 1160 to 1260 +/-5 mm, Back Width 480 mm at Top and

420mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 460+/-5 mm and Seat height 460mm to 560 mm

+/-5mm range. And over all chair width should be 615 +/-5mm and Overall chair depth should be 640 +/-

5mm. Seat should be made up of foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50%

deflection conforming to IS 3400. Seat, back & headrest shall be upholstered with Leatherette 75% PVC &

25% polyester – 640 GSM, Abrasion-100000 cycles over PU faom. The chair shall be supplied with Dynaflex

Two Piece Back Construction with cushion made by 25mm foam at 55kg/m3 density. Hardness of 25+3kgf at

Main HB 50% deflection conforming to IS 3400. Back shall be provided With 260mm width, 160mm height and Board Room

Chair 50mm height adjastable Headrest. The Chair should be provided with Synchro tilt Mechanism with three conference

Multi lock features. The mechanism shall allow 360 degree revolving feature along with height adjustablility.

One Way Adjustable Arms (Height) to be provied with height adjustment button made of Delrin P 500. The

mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be class 4 tested as per

ANSI BIFMA standards. Chrome Base to be provied. Twin castors 60 mm dia with PA6 material complying to

ANSI/ BIFMA X 5.1 2017 standards. the axle pin shall be rust protected zinc passivated. The base shall be

660 mm PCD (26 inches) five pronged bases made up of PA6, 30% glass filled reinforced with bottom ribbing

for additional buttress and strength. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and

GreenGuard Certification.

Mid Back Chair in Leatherite

The overall size of Chair shall be : Total height 1050 to 1150 +/-5 mm, Back Width 480 mm at Top and

420mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 4t0+/-5 mm and Seat height 460mm to 560 mm

+/-5mm range. And over all chair width should be 615 +/-5mm and Overall chair depth should be 640 +/-

5mm. Seat should be made up of foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50%

deflection conforming to IS 3400. Seat & back shall be upholstered with Leatherette 75% PVC & 25%

polyester – 640 GSM, Abrasion- 100000 cycles over PU foam. No flamming or progressive smoldering within

one hour of placement of the cigarettes. Fire rated fabric confirming to BS EN 1021 (match) should be used.

44 MB Chair The chair shall be supplied with Dynaflex Two Piece Back Construction with IS20D Mesh upholstred. The 22.00 25,462.98 560,185.61

Chair should be provided with Synchro tilt Mechanism – with three Multi lock features. The mechanism shall

allow 360 degree revolving feature along with height adjustablility. One Way Adjustable Arms (Height) to be

provied with height adjustment button made of Delrin P 500. The mechansim shall possess seat to back

recline ratio of 3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Chrome Base to

be provied. Twin castors 60 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. the

axle pin shall be rust protected zinc passivated. The base shall be 660 mm PCD (26 inches) five pronged

bases made up of PA6, 30% glass filled reinforced with bottom ribbing for additional buttress and strength.

The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

Providing and placing chair with Chair's Seat and back is made out of 12mm molded hot pressed plywood in

ergonomic shape fitted with Imported T-nuts and revited in to the wood.POWDER COATED 16 GAZE MS

round frame.Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair

Standards.Upholstery: Seat Cushion with pre moulded foam of 50 - 60 density Density -- 52 kg/m3 Hardness -

- 12.6kgf at 25%.This mechanism is manufactured out of cold Rolled Carbon Steel IS 513-1994 Sheets,The

45 steel components are manufactured with highly precision tools For accuracy in matching other parts for 24.00 15,050.00 361,200.00

smooth functioning. The steel components are fabricated by using Co2 welding process for giving uniform

surface finish with higher tensile strength. Back Frame is upholstered with Thinner Mesh Adjustable Lumbar

Support Allows you to adjust the lumbar support position for good back support and blood circulation.Moulded

self skinned polyurethene fixed Arms confirming to IS 7078 with steel insets for long life.Seat are duly

upholstered with approved fabric.

Digitally signed by AMIT

The overall size of meeting table shall be of size 2100 mm length x 1050 mm width & height 750 mm. The

worksurface of the table shall be made up of 25mm thick Pre-laminate particle board as per E1 norms and its

edges duly sealed with 2mm PVC Lipping on automatic machine at visible sides. Two sides of the work surface

shall be provided with reverse tapered edge design created by chamfering the board @ 45 degree inside for

17mm length & keeping 8mm straight & then edges sealed with 2mm thick PVC Lipping (not lesser) on Meeting

46 Table automatic machine. Understructure: The understructure of the Main table shall be provided with heavy duty 4 Room near 1.00 59,641.75 59,641.75

vertical legs made up of boat shaped having radius 170 mm CRCA MS tubes having max. size of 100 mm on reception

circular side x 40 mm flat x 1.6 for better durability. 4 nos Diamond Shape CRCA MS Tubes of size 55mm x

12mm x 61mm x 12mm x 55mm x 1.6 mm shall used as Horizontal cross beams under table top that shall

be connected to all 4 vertical legs through pressure die cast aluminium connector. The die cast connector

shall connect the leg and the horizontal beams neatly without any gap. The entire metal understructure shall

be powder coated. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

The overall size of discussion table in Dia. 1500mm X 750mm that is to be assembled at site. The table top

shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate

and finish as per approved shade. The table top profile shall be in circular shape and the edges shall be

sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted

with the assistance of edge banding machine. Leg: shall be made up of high pressure aluminum die casted

20 degree tapered, number “7” shape & oblong cross section of about 55mm on top, 45mm at bottom and of

725mm length to get 750mm table height, it acts as vertical structural support member, connected by a

horizontal cross beams 50x25x1.6thk (16g) ERW tube & connected to the Aluminium diecast vertical legs

through a high pressure Aluminium diecast connectors. The OEM shall have ISO 9001, ISO 14001, BIFMA

Level-2 and GreenGuard Certification.

The overall size of Chair shall be height 915 to 1015 +/-5 mm, Back Width 415 mm at Top and 450mm at

bottom, Seat Width 480 +/-5 mm, Seat Depth 440+/-5 mm and Seat height 460mm to 560 mm +/-5mm

range. over all chair width should be 560 +/-5mm and Overall chair depth should be 670 +/-5mm. Seat

should be made up of foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection

conforming to IS 3400. Seat shall be upholstered with micro fabric 100% polyster 180 GSM abrasion > 50000

cycles. No flamming or progressive smoldering within one hour of placement of the cigarettes. Fire rated

fabric confirming to BS EN 1021 (match) should be used. The back frame shall be made up of PPGF and the

injection molded in grey color, armrest also in grey color. The chair shall be supplied with Mesh Back rest. The

Chair should be provided with center tilt two position lock Mechanism. The mechanism shall allow 360 degree

revolving feature along with height adjustablility. Fixed arms connected to seat and back in the same contour.

The mechansim shall possess seat to back recline ratio of 1:1. The Gas Lift used shall be class 4 tested as per

ANSI BIFMA standards. Nylon Base in grey color to be provied. Twin castors 50 mm dia with PA6 material

complying to ANSI/ BIFMA X 5.1 2017 standards. the axle pin shall be rust protected zinc passivated. The

base shall be 660 mm PCD (26 inches) five pronged bases made up of PA6, 30% glass filled reinforced with

bottom ribbing for additional buttress and strength. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2

and GreenGuard Certification.

The Overall size of the table shall be 3000 mm L x 1200 mm D x 750 H. The worktop shall be made up of

25mm thick pre-laminated particle board of E1 norms. The sides of the worktop shall be sealed with 2mm

thick PVC Edge band. Strong & durable polycarbonate spacers should be provided between table top and

understructure of size of the spacer is 65 L x 25mm W x 15/20mm H. The understructure shall be made up of

MS powder coated legs having enhanced look with 08 faces trapezoidal cross section size 42.50mm x 8mm x

43.50mm x 5.50mm x 17mm x 5.5mm x 43.50mm x 8mm and thickness of 1.6mm. Edges of the leg should

not have sharp edges. For safety of users a radius of R3.20 mm should be provided. Each leg comes with nut

insert injection moulded leg bush of same shape as of trapezoidal cross section and fixed with leveler for

49 Table height adjustment upto 20mm. The vertical legs shall be connected by horizontal beams with the help of 1.00 55,883.41 55,883.41

aluminum die cast connector that joints the legs vertically and horizontally with pipe of cross section 50 x 25

mm x 1.6 mm thickness. The die cast connect size shall be L shaped having angle of 10 degrees for vertical

leg side. The Diecast connector will have same shape as of Trapezoidal vertical leg at one side and another

side matching to horizontal cross section 50x25. The cross beams below the worktop shall be made of 40 mm

x 20 mm ERW tubes & joined with the Legs frame through aluminium die cast connectors using 2 high tensile

Allen bolts of M6x20mm L. Centre support Leg shall be provided in the middle to support table as well as pass

electrical & data cables. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard

The overall size of Chair shall be Total height 885 +/-5 mm, Back Width 415mm at Top and 470mm at

bottom, Seat Width 490 +/-3 mm, Seat Depth 465+/-3 mm and Seat height 495mm +/-5mm . And over all

chair width should be 600 +/-5mm and Overall chair depth should be 585 +/-5mm. Seat shall be

upholstered with 100% polyster 180 GSM abrasion > 50000 cycles. No flamming or progressive smoldering

within one hour of placement of the cigarettes. Fire rated fabric confirming to BS EN 1021 (match) should be Meeting

used. The chair shall be supplied with Mesh at the back rest. The chair shall be supplied with injuction Room near

moulded Back rest with material of PA620%GF. The Chair understructure should be provided metal pedestal Corner cabin

chromeplated having castors of 50mm dia Twin castors PA6 material complying to ANSI/ BIFMA X 5.1 2017 4

standards. Fixed arms shall be connected to back rest with proper PP fitment and below the seat. armrest

shall beprovided with a polymer cover on the top gripped on the armrest. amrest pipe shall be chrome plated.

Centre tilt mechanism shall be provided with tilt tension adjustment. The OEM shall have ISO 9001, ISO

14001, BIFMA Level-2 and GreenGuard Certification.

Digitally signed by AMIT

The Overall size of the workstation cluster shall be 1200 mm L x 600 mm D x 1100 H/ 750 H. The cluster shall

have 4 individual workstations each of size 1200 mm L x 600 mm D. The worktop height shall be 750 mm &

height including partition screens shall be 1100mm. The worktop shall be made up of 25mm thick pre-

laminated particle board of grade E1 low emitting material. The understructure shall be made up of MS

powder coated legs having enhanced look with 08 faces trapezoidal cross section size 42.50mm x 8mm x

43.50mm x 5.50mm x 17mm x 5.5mm x 43.50mm x 8mm and thickness of 1.6mm. Edges of the leg should

not have sharp edges. For safety of users a radius of R3.20 mm should be provided. The vertical legs shall be

connected by horizontal beams with the help of aluminum die cast connector that joints the legs vertically

and horizontally with pipe of cross section 50 x 25 mm x 1.6 mm thickness. The die cast connect size shall be

L shaped having angle of 10 degrees for vertical leg side. The Diecast connector will have same shape as of

Trapezoidal vertical leg at one side and another side matching to horizontal cross section 50x25. The

Intermediate leg: Two Verticals of Intermediate leg will have to be with 60x40mm rectangular ERW tubes and

both legs are joined using a beam section of 40x40x1.6mm thk at the top side. The 60x40 verticals to have

desk base through “U” notch or through cut out of 40x41mm size at the top side to locate 40x40 cross beam. For ease workstation

workstation of wire management, a 450 mm length & 142mm breadth flip up cover made up of aluminum having soft area

closure & with option to fix laptop ring should be provided. A flip down mechanism enabled cable tray shall be

provided below the worktop to mount switches and sockets. The front fabric screen shall be provided of size

1050 mm L x 350 mm ht. made up of 18 mm thick prelam particle board of grade E1 upholstered by fabric,

having aluminum extrusion at all three sides having cross section size of 12mm x 5mm & joined at all 4

corners with Zinc mazak5 die cast connector of size 15 L x 15 H x 12mm W.

Pedestal - 2D+1F in size of 400W X 450D X 600Ht. The prelaminated particle board of approved shade

confirming to E1 norms. Top & Sides shall be18mm Thk pre laminated particle board. Back panel shall be 9

mm Thk pre laminated particle board. Edge: All exposed area with 2mm thick PVC edge lipping on automatic

machine. The drawers front & filling shall be provided with sleek finger groove handle less design for a

streamlined look. Finger groove shall be created by providing a reverse tapered profile edge of 6mm straight

surface & 12 mm tapered towards inside @ 45 degree & then sealed with minimum 2mm thick PVC lipping on

automatic machine. Regular lock shall be provided. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2

and GreenGuard Certification.

The Overall size of the main table shall be 1500 mm L x 750 mm D x 750 H & side storage shall be 900 x 450

x 750 H with side storage 2400 x 450 x 740 (WDH)mm.The worktop shall be made up of 25mm thick pre-

laminated particle board of E1 norms. The modesty panel shall be of 18mm thick PLPB E1 norms. The sides of

the worktop shall be sealed with 2mm thick PVC Edge band. Strong & durable polycarbonate spacers should

be provided between table top and understructure of size of the spacer is 65 L x 25mm W x 15/20mm H. The

understructure shall be made up of MS powder coated legs having enhanced look with 08 faces trapezoidal

cross section size 42.50mm x 8mm x 43.50mm x 5.50mm x 17mm x 5.5mm x 43.50mm x 8mm and

thickness of 1.6mm. Edges of the leg should not have sharp edges. For safety of users a radius of R3.20 mm

should be provided. Each leg comes with nut insert injection moulded leg bush of same shape as of

trapezoidal cross section and fixed with leveler for height adjustment upto 20mm. The vertical legs shall be

connected by horizontal beams with the help of aluminum die cast connector that joints the legs vertically workstation

52 Open table and horizontally with pipe of cross section 50 x 25 mm x 1.6 mm thickness. The die cast connect size shall be area/Open 24.00 55,800.00 1,339,200.00

L shaped having angle of 10 degrees for vertical leg side. The Diecast connector will have same shape as of office

Trapezoidal vertical leg at one side and another side matching to horizontal cross section 50x25. The cross

beams below the worktop shall be made of 40 mm x 20 mm ERW tubes & joined with the Legs frame through

aluminium die cast connectors using 2 high tensile Allen bolts of M6x20mm L. Side storage shall be made up

of 18mm thk pre laminated particle board E1 norms, Back : 9mm Thk pre laminated particle board, one side

having shutter storage with shelves and other side 3 drawer units. All exposed area with 2mm thick PVC edge

lipping The drawers front, filling & shutter top edges shall be provided with sleek finger groove handle less

design for a streamlined look. Finger groove shall be created by providing a reverse tapered profile edge of

6mm straight surface & 12 mm tapered towards inside @ 45 degree & then sealed with minimum 2mm thick

PVC lipping on automatic machine. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard

The overall size of Chair shall be width 600 +/-5mm, depth 640 +/-5mm. Total height shall be 995 to 1095

+/-5 mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-5

mm and Seat height 470mm to 570 mm +/-5mm range. Seat shall be made up of foam pre moulded at 55

kg/m3 density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered

with micro fabric 100% polyster 180 GSM abrasion > 50000 cycles. Fire rated fabric confirming to BS EN 1021

(match) should be used. The chair shall be supplied with Mesh Back rest. The back frame shall be made up of

Mid Back Injection molded PPGF 20%. Adjustable Lumbar Support made up of PU having size 365 mm x 110 mm x

Chair 25mm thick shall be provided for better comfort. The Chair should be provided with Self Calibrating Multilock

Mechanism (Bio Snchyro mechansim) that should adjust the tension of the back sensing weight of the user.

The mechanism shall allow 360 degree revolving feature along with height adjustablility. One Way Adjustable

Arms (Height) to be provied with height adjustment button made of Delrin P 500. The mechansim shall

possess seat to back recline ratio of 3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA

standards. Nylon Base to be provided. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and

GreenGuard Certification.

Supplying, and placing in position similar to executive dining table as per image. the dining table collection

flaunts clean silhouettes with tapered legs. Crafted with solid wood, the dark oak finish accentuates the

distinctive wood grains with glass top. this dining table is made to seat up to four people comfortably.

Material & Subtype Solid Wood - Beech Wood, Table Top Material Clear 10mmthk toughened Glass, Leg Cafeteria

Material Solid Wood, Finish Glossy, Colour & Colour Family Brown - Walnut. The product should be as per table

above given specification under the guidance of project architect & Engineer in charge. Sizes may slightly

vary as per requirement os site / selection of client/Engineer Incharge Dimension (L) 1150mm X (D) 750mm

Digitally signed by AMIT

Supplying, and placing in position similar to executive dining chair as per image. our dining chair effortlessly

blends with any aesthetic. Masterfully built of solid wood, the gently curved slatted back and soft fabric

wrapped firm cushioned seat offer just the right amount of support.Masterfully crafted of solid wood in

Mahogany Brown finish.Kiln-dried solid wood construction makes it warp and scratch-resistant.Premium fabric

upholstery in Pearl White feels soft and sumptuous.Firm cushioned seat offer a comfortable seating

55 café chair experience.Slatted backrest design adds a timeless appeal.Comfortable seat depth & height for every 18.00 4,525.00 81,450.00

generation.Material & Subtype Solid Wood - Rubber Wood,Frame Material Solid Wood Upholstery Material

Fabric,Filling Material Foam,Seat Material Fabric, Leg Material Solid Wood, Finish Matte,Colour & Colour

Family Brown - Mahogany,White - Pearl, Dimension (W)490mm X (D)515mm X (H)820mm,Seating Height

485mm. The product should be as per above given specification under the guidance of project architect &

Engineer in charge. Sizes may slightly vary as per requirement os site / selection of client/Engineer Incharge

Storage rack cum white board cum movable physical partition of Size - 400L x 900D x 1800H. It shall be

made up of 18mm thick Pre-laminate particle board E1 norms duly finished with 2mm pvc edge banding on

automatic machine and all the structure should be fixed by mini fixed. At bottom 75mm PVC 4 castors are

56 Crehce fixed with metal frame. One side shall be upholstered with fabric and another one side shall be provided with Crehce 0.00 63,385.72 0.00

white board. Both side pannel edge should be cover with rubber bending. At the top to joint the both side

pannel aluminium extrusions trim shall be used and it shall be finished in brushed aluminium finish. The OEM

shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

Magazine Rack, specifications, Size - 760 L x 430-100 D x 1000 H, The Rack shall be made up of 18mm thick

Pre-laminate particle board E1 norms duly finished with 2mm pvc edge banding on automatic machine.Rack

shall have 7 particular shelf for storage.its come with size of 760mm Length with bottom depth is 430mm but

at top 100mm depth. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

Cube Pouffes, specifications. Size - 410W x 390D x 385H

Seat shall be upholstered with SF fabric, Polyester & Viscose - 300 GSM, Abrasion- > 45000 cycles. No

flaming or progressive smouldering within one hour of placement of the cigarettes. Fire rated fabric

58 Crehce confirming to BS EN 1021(match). Foam: Cushion with pre moulded foam of 50 kg/m3 density in the shape of Crehce 0.00 101,794.42 0.00

Cube shall be used having Hardness – 30 ± 3 kgf at 50% deflection. Frame Upholstery done with MS frame

welded in CO2 welding process for uniform finish conforming to IS 816. Bushes: Bushes fixed shall be molded

to hexagonal bolt. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

Saddle (Pouffes) Size - 800W x 400D x 500H

Seat shall be upholstered with SF fabric, Polyester & Viscose - 300 GSM, Abrasion- > 45000 cycles. No

flaming or progressive smouldering within one hour of placement of the cigarettes. Fire rated fabric

confirming to BS EN 1021(match) Foam: Cushion with pre moulded foam of 50 kg/m3 density in the shape of

Cube shall be used with Hardness – 30 ± 3 kgf at 50% deflection. Frame : Upholstery shall be done done

with MS frame welded in CO2 welding process for uniform finish conforming to IS 816. The OEM shall have

ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

The overall size of the table shall be 1050 L x 525 D x 450 H mm. The top surface of the table shall be in boat

shape design having maximum size at the middle & lesser at the ends to form this unique shape. The table

top shall be made up of 18mm thick Prelaminated particle board of E1 norms. The edges shall be sealed

properly with 2mm thick PVC edge banding on automatic machine. The understructure of the table shall be

made from solid wood i.e properly treated & seasoned kiln dried beach wood, finished with clear synthetic PU

coating for the best resilence and high durability. The legs and the frame shall be joined together by method

of tenon and mortise for durability and better aesthetics. Four legs shall be provided and the cross section of

leg at the bottom shall be 35x35 and top shall be 55x35 provided in tappered finish for better looks. The

outer side of the legs shall be rounded & inner side shall be corner edges. The wooden frame shall be of size

55mm x 22mm thick with visible face of 55 mm front and 22mm shall be below the table top running at all

four ends as well as one support in the middle. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and

GreenGuard Certification.

Circular Puffe of size 600 W x 600 D x 450 H. specifications: Seating: Fabric shall be used as upholstery with

SF fabric, Polyester & Viscose - 300 GSM, Abrasion- > 45000 cycles. No flaming or progressive smouldering

within one hour of placement of the cigarettes. Fire rated fabric confirming to BS EN 1021(match), IS 15061-

61 Crehce 2002 is optional. Foam: Cushion with pre moulded foam of 50 kg/m3 density in the shape of Cylinder shall be Crehce 4.00 13,814.14 55,256.54

used with Hardness – 30 ± 3 kgf at 50% deflection. Frame : Upholstery shall be done with MS frame welded

in CO2 welding process for uniform finish conforming to IS 816. The OEM shall have ISO 9001, ISO 14001,

BIFMA Level-2 and GreenGuard Certification.

62 Crehce SITC of bunk bud as per approved design. Crehce 1.00 32,000.00 32,000.00

Digitally signed by AMIT

The overall size of the chair shall be 690 width x 750 height and 580 mm depth. The seat height shall be

460mm. The chair understructure shall have 4 legs that should be interconnected with each other through

frame. The understructure of the chair shall be made from solid wood i.e properly treated & seasoned kiln

dried beach wood, finished with clear synthetic PU coating for the best resilence and high durability. The legs

and the frame shall be joined together by method of tenon and mortise for durability and better aesthetics.

Lounge Four legs shall be provided and the cross section of leg at the bottom shall be 35x35 and top shall be 55x35 waiting

Chair provided in tappered finish for better looks. The outer side of the legs shall be rounded & inner side shall be lounge

corner edges. The wooden frame shall be of size 55mm x 22mm thick with visible face of 55 mm front and

22mm shall be below the seat. The seat & back shall be made up of insitu molded PU foam having seat, back

& side armrests entire connected. The entire seat shell shall be uphosterd with high quality polyester fabric.

Wood shall be polished in desirable shade for better appearance. The OEM shall have ISO 9001, ISO 14001,

BIFMA Level-2 and GreenGuard Certification.

Centre table Size

The overall size of the Centre table shall be 1200 mm Length x 600 mm depth, 450 mm height. the table top

shall be made up of 18mm thick prelaminated particle board of approved shade All the edges of discussion

surface shall be provided with machine pressed 2mm thick PVC lipping glued with hotmelt Eva glue free from waiting

64 any VOC. Under Structure Support: Table top shall be supported on CRCA legs duly powder coated. The Chair /Lounge Area 5.00 11,369.92 56,849.59

understructure should be provided with 32mm by 1.6mm thickenss swaged tube from 32mm top and 19mm 02/03

bottom. The edges of the table top shall be rounded & edges shall not be sharp. The legs shall be in angular

design & thicker on the top & thinner on the bottom side. The OEM shall have ISO 9001, ISO 14001, BIFMA

Level-2 and GreenGuard Certification.

The overall size of the corner table shall be 600 mm Length x 600 mm depth, 450 mm height. the table top

shall be made up of 18mm thick prelaminated particle board of approved shade All the edges of discussion

surface shall be provided with machine pressed 2mm thick PVC lipping glued with hotmelt Eva glue free from waiting

65 any VOC. Under Structure Support: Table top shall be supported on CRCA legs duly powder coated. The Chair /Lounge Area 9.00 8,520.00 76,680.00

understructure should be provided with 32mm by 1.6mm thickenss swaged tube from 32mm top and 19mm 02/03

bottom. The edges of the table top shall be rounded & edges shall not be sharp. The legs shall be in angular

design & thicker on the top & thinner on the bottom side. The OEM shall have ISO 9001, ISO 14001, BIFMA

Level-2 and GreenGuard Certification.

Providing & placing compactor in two bay configuration drive type. The size of each storage body shall be of

width 915 mm, depth 380 mm and a height of 1980 mm (overall variance +/- 50 mm) including the storage

body height with undercarriage All the part items, like front mechanism box, shelvings, clading sheet etc.

shall be made out of superior quality of CRCA sheets. The compactor should consist of storage units movable

and bolted to undercarriage which shall rolls on the channels firmly embedded to the ground. The main body

should be rigid knock down construction made of out of Side /tack/top Panels made up of min 0.8mm thick

CRCA steel. Each body should consists of one single fixed unit, one double mobile one single mobile unit and

add on. Each unit should have 5 loading levels formed by 4 nos of adjustable shelves. The shelf should be

made of 0.8mm thick CRCA steel to having 40-50 Kg UDL capcity. The shelves should be mounted on support

brackets & its level should be adjustable. The under carriage should be made with HR sheet min 2.5 min

suitably fabricated using welding to take the loads. The MSU should be running on a guidetrack of size 28 mm

M.S. round with necessary bracing/channel and base plate. Rails should be 25 mm square bright bar. The

66 Compactor Record Room 14.00 49,603.21 694,444.98

bodies including shelves and undercarriages should be given 7 tank antirust surface treatments and finished

with powder coating using epoxy polyester powder of 50-60microns. A centralized or independent locking

arrangement should be provided through the locking stiffener mounted onto back of single last unit so that it

gets locked on channels when all the units are brought together. All the units should be provided with chrome

plated handles. All the MSU should be provided with the features such as mechanical drive with a handle for

mechanically assisted drive mechanism consisting of a series of sprocket and chain mechanism for smooth

movement of the compactor with minimum effort. It should be fitted with safety guard which is to be

engaged when entering the common aisle to prevent from operating system when an individual is inside. The

guide track should be provided with an end stopper to avoid derailment of the units. it should be provided

with the label holders. Qty mentioned is for single body including entire accessories and mechanism to enable

its placement & usage. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard

Digitally signed by AMIT

Providing & placing compactor in One bay configuration Push Pull type. The size of each storage body shall be

of width 915 mm, depth 380 mm and a height of 1980 mm (overall variance +/- 50 mm) including the

storage body height with undercarriage All the part items, like front mechanism box, shelvings, clading sheet

etc. shall be made out of superior quality of CRCA sheets. The compactor should consist of storage units

movable and bolted to undercarriage which shall rolls on the channels firmly embedded to the ground. The

main body should be rigid knock down construction made of out of Side /tack/top Panels made up of min

0.8mm thick CRCA steel. Each body should consists of one single fixed unit, one double mobile one single

mobile unit and add on. Each unit should have 5 loading levels formed by 4 nos of adjustable shelves. The

shelf should be made of 0.8mm thick CRCA steel to having 40-50 Kg UDL capcity. The shelves should be

mounted on support brackets & its level should be adjustable. The under carriage should be made with HR

sheet min 2.5 min suitably fabricated using welding to take the loads. The MSU should be running on a

67 Compactor Record Room 7.00 45,146.11 316,022.79

guidetrack of size 28 mm M.S. round with necessary bracing/channel and base plate. Rails should be 25 mm

square bright bar. The bodies including shelves and undercarriages should be given 7 tank antirust surface

treatments and finished with powder coating using epoxy polyester powder of 50-60microns. A centralized or

independent locking arrangement should be provided through the locking stiffener mounted onto back of

single last unit so that it gets locked on channels when all the units are brought together. All the units should

be provided with chrome plated handles. All the MSU should be provided with the features such as

mechanical drive with a push push handle to move the units. It should be fitted with safety guard which is to

be engaged when entering the common aisle to prevent from operating system when an individual is inside.

The guide track should be provided with an end stopper to avoid derailment of the units. it should be

provided with the label holders. Qty mentioned is for single body including entire accessories to enable its

placement & usage. The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

The overall size shall be 900 x 450 x 1800 (WDH) mm. Top shall be made up of 18mm thick pre laminated

particle board and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge

Full Ht lipping, Shutters shall be made up of 18 mm thick pre laminated particle board. 4 Shutters to be provied for

Storage uper & lower compartment. Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. Locking

faciltity should be provided for safe storage of documents. The prelaminated board used shall be of E1 norms.

The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

The overall size shall be 750 x 450 x 1800 (WDH) mm. Top shall be made up of 18mm thick pre laminated

particle board and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge

Full Ht lipping, Shutters shall be made up of 18 mm thick pre laminated particle board. 4 Shutters to be provied for

Storage uper & lower compartment. Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. Locking

faciltity should be provided for safe storage of documents. The prelaminated board used shall be of E1 norms.

The OEM shall have ISO 9001, ISO 14001, BIFMA Level-2 and GreenGuard Certification.

The overall size shall be 750 x 450 x 1200 (WDH) mm. Top shall be made up of 18mm thick pre laminated

particle board and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge

lipping, Shutters shall be made up of 18 mm thick pre laminated particle board. 4 Shutters to be provied for

uper & lower compartment. Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. The hinged

70 doors top shall be provided with finger groove handle-less design for a streamlined look. Finger groove shall Hall Storage 11.00 13,643.90 150,082.93

be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered towards

inside at 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Locking

faciltity should be provided for safe storage of documents. The OEM shall have ISO 9001, ISO 14001, BIFMA

Level-2 and GreenGuard Certification.

The overall size shall be 1200 x 450 x 1200 (WDH) mm. Top shall be made up of 18mm thick pre laminated

particle board and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge

lipping, Shutters shall be made up of 18 mm thick pre laminated particle board. 4 Shutters to be provied for

uper & lower compartment. Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. The hinged

71 doors top shall be provided with finger groove handle-less design for a streamlined look. Finger groove shall Hall Storage 2.00 24,585.94 49,171.88

be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered towards

inside @ 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Locking

faciltity should be provided for safe storage of documents. The OEM shall have ISO 9001, ISO 14001, BIFMA

Level-2 and GreenGuard Certification.

The overall size shall be 1050 x 450 x 1200 (WDH) mm. Top shall be made up of 18mm thick pre laminated

particle board and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge

lipping, Shutters shall be made up of 18 mm thick pre laminated particle board. 4 Shutters to be provied for

uper & lower compartment. Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. The hinged

72 doors top shall be provided with finger groove handle-less design for a streamlined look. Finger groove shall Hall Storage 1.00 19,101.98 19,101.98

be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered towards

inside @ 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Locking

faciltity should be provided for safe storage of documents. The OEM shall have ISO 9001, ISO 14001, BIFMA

Level-2 and GreenGuard Certification.

Digitally signed by AMIT

The overall size shall be 900 x 450 x 1200 (WDH) mm. Top shall be made up of 18mm thick pre laminated

particle board and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge

lipping, Shutters shall be made up of 18 mm thick pre laminated particle board. 4 Shutters to be provied for

uper & lower compartment. Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. The hinged

73 doors top shall be provided with finger groove handle-less design for a streamlined look. Finger groove shall Hall Storage 3.00 16,371.65 49,114.94

be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered towards

inside @ 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Locking

faciltity should be provided for safe storage of documents. The OEM shall have ISO 9001, ISO 14001, BIFMA

Level-2 and GreenGuard Certification.

Total Amount INR 18,200,789.93

Total Amount INR 18,200,789.93

Digitally signed by AMIT

Sr No Item Description Unit Total Qty Unit Rate Total

SITC of 98" Interactive Display with resolutions of 3840x2160 (4k), Brightness of

1 500cd/m2. Android version, Android 11, Ram 4 GB, Flash memory 32GB Nos 1 921,985.43 921,985.43

complete with all accessories like mounting bracket, etc as required

SITC of 86" 4k, DLED ,UHD Professional Signedge Display with 500 NITS, 24*7 ,

Built in SOC/ Media Playerwith Quad Core Processor, Built in Open Platform

Android 11, 28% Haze, OPS Slot, 3X HDMI, Audio Input Audio Output, Built in

Speaker(12W x 2) ;Including mounting bracket, Built-in Chromecast, Dolby

Digtial audio HDMI-CEC device linking supported, 3 USB(2.0), 3*HDMI(2.0

Side), Headphone Out, 1 *RJ 45, SPDIF out, Built In 2.4 GHZ Wifi,CPU Built in

Mali G31 MP2 GPU-A55*4, 1.1 GHz Processer, 4 GB RAM 32GB Storage,Metal

Frame 12 W built speakers, With 3 years on Site Warranty etc all complete

SITC of 75" 4k, UHD Professional Signedge Display with 400 NITS, 24*7 ,Built in

SOC/ Media Player with Quad Core Processor, Built in Open Platform Android

11, With Built in Bluetooth, 2X HDMI, Audio Input Audio Output, Built in

Speaker(10W x 2) ;Including mounting bracket, Built-in Chromecast , HDMI

3 Arc, Dolby Digtial audio, The built-in SOC is powered by Google's Android Nos 7 189,874.00 1,329,118.00

Platform, HDMI-CEC device linking supported, 2 USB(2.0), 3*HDMI(2.0 Side),

Headphone Out, 1 *RJ 45, SPDIF out, Built In 2.4 GHZ Wifi,CPU Built in With

Cortex-A55*4, 1.1 GHz Processer, 2 GB RAM, 20 W built speakers, With 3 years

on Site Warranty

SITC of 75" 4k, Android 13,UHD Interactive Display with 450 NITS, 24*7 ,Inbuilt

Quad Core Processor and with 1.9Ghz (A55 x 4) , 4 GB RAM & 32GB

Storage,Toughend Glass with Level 7 of MOHS Standrad, 3X HDMI (4K upto

4 60Hz), HDCP 2.1,CEC , ARC (HDMI 1), 1 xVGA, 1x USB 2.0,4 x USB 3.0 (Front 2 , 1 307,202.28 307,202.28

Rear 2) with auto switching function, 1 x Type C Touch,PD 65W & LAN Network

Sharing , 1x Audio In, Built in Speaker(20W x 2) , 2 x writing pens , 40 Point

Touch, etc all complete

SITC of 65" 4k, UHD Professional Signedge Display with 400 NITS, 24*7 ,Built in

SOC/ Media Player with Quad Core Processor, Built in Open Platform Android

11, With Built in Bluetooth, 2X HDMI, Audio Input Audio Output, Built in

Speaker(10W x 2) ;Including mounting bracket, Built-in Chromecast , HDMI

5 Arc, Dolby Digtial audio, The built-in SOC is powered by Google's Android Nos 4 117,522.72 470,090.87

Platform, HDMI-CEC device linking supported, 2 USB(2.0), 3*HDMI(2.0 Side),

Headphone Out, 1 *RJ 45, SPDIF out, Built In 2.4 GHZ Wifi,CPU Built in With

Cortex-A55*4, 1.1 GHz Processer, 2 GB RAM, 20 W built speakers, etc all

SITC of 55" 4k, UHD Professional Signedge Display with 400 NITS, 24*7 ,Built in

SOC/ Media Player with Quad Core Processor, Built in Open Platform Android

11, With Built in Bluetooth, 2X HDMI, Audio Input Audio Output, Built in

Speaker(10W x 2) ;Including mounting bracket, Built-in Chromecast , HDMI

6 Arc, Dolby Digtial audio, The built-in SOC is powered by Google's Android Nos 4 85,163.04 340,652.17

Platform, HDMI-CEC device linking supported, 2 USB(2.0), 3*HDMI(2.0 Side),

Headphone Out, 1 *RJ 45, SPDIF out, Built In 2.4 GHZ Wifi,CPU Built in With

Cortex-A55*4, 1.1 GHz Processer, 2 GB RAM, 20 W built speakers, etc all

SITC of Fixed Wall Mount, capable of holding up to 75 kg and supports 37" to

90" displays, VESA Compliant etc all complete

SITC of ultra thin retractable touch moniter lifter with screen. Material: full

aluminium alloy, Moniter: 15.6 inches fhd screren (16:9), resolution ration:

8 1920*1080, screen brightness: 400 cd/m2, contrast: 1500:1 full angle automatic Nos 1 243,136.96 243,136.96

pitch angle: 0-30 degree manaul pitch angle: 0-30 degree, interface:

HDMI+RS232 I/O+USB with anti-pinching function etc. all complete.

Cable Cubby with flip top, cover and 6 Pass Through Holes for multi-format

9 cables, 2 Universal Power Socket , 1 HDMI, 1 USB-C for Data Transfer, made of Nos 17 36,695.04 623,815.74

aluminium etc all complete

SITC of Wireless Presentation Platform, allows simultaneous content sharing for

up to four 1080p presenters, Wireless screen casting with iOS, Android, Mac,

Chromebook, and Windows devices through native AirPlay, Google Cast, or

Miracast protocols, Supports YouTube Live streaming, Local storage available

for playback of images and video, WPA2-PSK, and AES-128 encryption, with

two wireless dongel etc all complete

SITC of All in One Conference Unit, Camera Sensor 1/2.5″, CMOS, Effective

Pixel: 8.0M, 4 x MEMS mic array, AEC | ANS | AGC 180° Pickup Angle pickup

11 Range: 5-8m (16-26ft) A.I. camera with smart backlighting, auto-framing, Nos 5 290,813.67 1,454,068.37

speaker & presenter tracking, Inputs / Outputs 1x USB-C Input with Alt-Mode,

1x HDMI Input, 1x HDMI Output etc all complete

SITC of Network PTZ Conference Camera, 12x optical zoom and 60° horizontal

FoV, 1/2.8” low-noise CMOS Sensor, Sensor Scanning Mode: Progressive,

Horizontal Rotation Range: ±170°, Vertical Rotation Range: -30° to +90°,

Image rotation for ceiling mounting, White Balance: Auto, indoor, outdoor,

one-push, manual, specified color temperature, IP Stream Resolutions: H.264

@ 360p, 270p or 180p, a single network cable for video, power and control

data transport, HDMI 2.0 and 3G-SDI Outputs Power Over Ethernet (PoE)

support etc all complete

SITC of Universal Switcher with HDMI and USB-C connectivity, 2 HDMI Inputs, 2

USB-C connectivity (4K Video, Audio, Data, Power charge), 2 HDMI Outputs, 4

USB-A 3.0 Connection (for USB Devices), 2 USB-B 3.0 Connection (for PC hosts),

13 USB host switching, Analog audio de-embedding, Charging via USB-C up to Nos 6 380,269.57 2,281,617.39

60w, Supports HDMI 4K signal formats (4K UHD @60Hz RGB 4:4:4, up to 18

Gbps), DP Alt Mode, HDMI 2.0, HDMI 1.x, DVI Signal Support, HDCP 1.x, HDCP

2.2 support etc all complete

SITC of 8 Inputs and 8 Outputs HDMI 2.0 Compatible Full 4K Matrix Switcher,

Supports HDMI 4K signal formats (4K UHD @60Hz RGB 4:4:4, up to 18 Gbps),

HDCP 2.2 and HDCP 1.4 compliant with cross conversion capabilities, HDMI

14 2.0, HDMI 1.4 and DVI 1.0 compliant, HDR and Low Latency Dolby Vision Nos 1 700,921.00 700,921.00

support, Audio de-embedding, HDCP 2.2 and HDCP 1.4 compliant,

Advanced EDID Management, Fully non-blocking switching architecture etc

SITC of HDMI 2.0 Extender (Transmitter) , Supports HDMI 4K signal formats (4K

UHD @60Hz RGB 4:4:4, up to 18 Gbps), Bi-directional PoC remote powering,

Extends HDMI 2.0, audio, Ethernet, RS-232 up to 100m over one CATx cable,

HDR and Low Latency Dolby Vision support, Bi-directional RS-232 extension

(pass-through),HDCP 2.3 compliant (transparent pass-through) etc all

SITC of HDMI 2.0 Extender (Reciever) , Supports HDMI 4K signal formats (4K

UHD @60Hz RGB 4:4:4, up to 18 Gbps), Bi-directional PoC remote powering,

Extends HDMI 2.0, audio, Ethernet, RS-232 up to 100m over one CATx cable,

HDR and Low Latency Dolby Vision support, Bi-directional RS-232 extension

(pass-through),HDCP 2.3 compliant (transparent pass-through) etc all

SITC of Boundary Layer Microhone Cardioid, Supercardioid and

Omnidirectional polar patterns Programmable, Silent membrane switch, TTL

17 Logic LED input and TTL Logic switch ouput LED indicator, Cardioid: -27.5 Nos 13 41,181.85 535,364.02

dBV/Pa (42.2 mV) Supercardioid: -26.5 dBV/Pa (47.3 mV) Omnidirectional: -

22.0 dBV/Pa (79.4 mV) Dynamic Range 1 kΩ load at 1 kHz: 94DB

SITC of Wireless System with Handheld Transmitter, Supercardioid Dynamic

Microphone capsule , 24-bit digital audio, Extended 20 Hz to 20 kHz frequency

range, 118 dB dynamic range, Digital predictive switching diversity, 44 MHz

tuning bandwidth, 32 available channels per frequency band, Up to 10

compatible systems per 6MHz TV band; 12 systems per 8 MHz band, RF Carrier

Frequency Range: 470–937.5 MHz, Working Range 100 m (328 ft), Network

Interface, RF Power: 10 mW, Antenna Type: Integrated Single-Band Helical, Up

to 8 hours from 2 AA batteries or rechargeable battery etc all complete

SITC of Fully Integrated Audio, Video and Control Solution, 128 Networked

Audio Channel, 24 Channels of analog I/O, including 8 configurable Flex

channels, 16 AEC Processor, Up to 32 x 32 Dante audio channels (8 x 8

included), USB AV bridging (16 x 16 audio + Camera Support), Full-featured

Control engine (with Feature License), Up to 4x VoIP Instances, External USB

audio device host etc all complete

SITC of 6.5-inch, 2-Way Ceiling Speaker, Rated Power: 60W, Frequency Range:

65 Hz – 20 kHz, Sensitivity: 88 dB, Rated Coverage 135° conical DMT, Maximum

20 continuous SPL 106 dB, Nominal impedance: 8 / 16 Ohm, Transformer taps: Nos 8 30,773.63 246,189.06

60W / 30W / 15W at 100 / 70V, IP-34 Rated, Low-saturation and low-loss

70/100V transformers with 16Ω bypass, UL and CE Certified etc all complete

SITC of 4 Channel Class-D Amplifier, Power (per channels driven): 200 W at 8 Ω

/ 4 Ω / 100V / 70V, FlexAmp Technology, Frequency Response: 20 Hz – 20 kHz,

21 Signal to Noise > 103 dB, Input impedance >10k, balanced or unbalanced, Nos 1 231,638.85 231,638.85

User-configurable operating modes, UL, CE, RoHS/WEEE compliant etc all

SITC of Expension Module for RS232 / Communication Port, Gigabit LAN, Four

22 bi-directional RS232 serial ports, Power over Ethernet (PoE) capable etc all Nos 1 88,505.22 88,505.22

SITC of 4 x 4 USB 3.2 Gen 1 Industrial Hub Switch Enables 4 computers to share

23 4 USB 3.2 Gen1 devices Support port selection via remote controller or RS- Nos 1 47,070.98 47,070.98

422/RS-485 link through 5-pin terminal block

SITC of 10.2" Apple iPad LED-backlit Multi-Touch display with IPS technology

with User Control Interface (UCI) Deployment etc all complete

SITC of 16-port Gigabit Ethernet High-Power PoE+ Smart Switch with 2 SFP Ports

and Cloud Management etc all complete

26 SITC of Wireless Access Point etc all complete Nos 2 16,264.94 32,529.87

SITC of 2m/6.5ft HDMI 2.0 Cable, 18Gbps 4K60Hz, Dolby Vision & HDR,

ARC,CEC, ALLM, VRR, | CL3 & VW-1 Rated etc all complete

SITC of 5 Meter Premium High Speed HDMI 2.0b Flexy Cable, Bandwidth up to

18Gbps, Up to 4096x2160@60Hz at RGB 4:4:4 video resolution, High Dynamic

Range (HDR10), Dolby Vision and Hybrid log–gamma (HLG) video etc all

SITC of 10m HDMI 2.0 AOC | 24Gbps | 4K60Hz | Dolby Vision & HDR | ARC,

CEC, ALLM & VRR | ISF Certified | FT4, CL4 etc all complete

SITC of 2m/6.5ft USB-C to C Cable | SuperSpeed USB 20Gbps | 4K60 Alt-

Mode | 100w PD etc all complete

SITC of USB-C to C Active Optical Cable | 5Gbps Superspeed | 4K60 Alt-

Mode | 60W PD | Screw-Lock Connector (15m/49ft) etc all complete

SITC of 2 Conductor 16 AWG Speaker Cable, stranded Bare copper

32 conductors, PVC/Nylon insulation, PVC jacket (as per actual) etc all Meter 100 155.64 15,564.13

33 SITC of Microphone cable etc all complete Meter 200 82.45 16,489.57

SITC of Category 6A Cable, 4 Pair, S/FTP, PVC jacket (as per actual) etc all

SITC of 24U, Equipment Rack, with Front & Side doors, 4 No Fan Assembly, on

Top of the Rack, 4 Caster wheels, 2 no Shelfs to mount the equipments which

are not rack mounted, 8X2, 5/6 Amp. Power Distribution Unit, Cable Manager

& Sufficient Rack hardwares etc all complete

Interior Fit-Out Works in The Office Space of the MSTC at World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR PLUMBING & FIRE FIGHTING

SECTION DESCRIPTION S.I (AMOUNT) N.S.I (AMOUNT)

A SANITARY FIXTURES & FITTINGS 7,514.65 723,084.13

B WATER SUPPLY 594,099.25 0.00

C INTERNAL DRAINAGE (SOIL, WASTE & VENT PIPES) 597,435.50 23,000.00

D SPRINKLER PIPING & ACCESSORIES 1,289,635.00 266,808.00

Total Cost ( Carried Forward) in Rs. 3,501,576.53

Digitally signed by AMIT

BOQ FOR PLUMBING & FIRE FIGHTING

SUB HEAD A: SANITARY FIXTURES & FITTINGS

SL. NO. DSR - DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) NS Amount (Rs)

Supply, installation, testing and commissioning of glazed

vitreous china single trap syphonic pattern having back

inlet, supporting chair, wall hung water closet complete

with all internal fittings/ accessories and CP brass flush bend

(European type) water closet with seat and lid, with C.P.

1 MR brass hinges and rubber buffers, adapter, rubber joints fixed

to W.C., C.P. brass screwed washers including cutting and

making good the walls and floors wherever required and

HDPE WC pan connector including jointing with white

cement complete in all respects.

Wall hung W.C. pan (White colour)with white plastic seat &

lid "Thermoset moulded ( bakelite ) IS 2548 Part I Each 7 20,000.00 140,000.00

Supply, installation, testing and commissioning of concealed

2 MR cistern including flush plate and all internal fittings/

accessories including cutting and making good the walls

and floors wherever required complete in all respects. Each 7 12,000.00 84,000.00

Providing and fixing C.P. SS shower assembly comprising of

3 MR shower head and arm, diverter, spout and other

equipment/ accessories complete as per selection of client/

engineer-in-charge: (Total base Rate - Rs. 45,000/-) Each 1 46,834.00 46,834.00

Supply, installation, testing and commissioning of glazed

vitreous china wash basin with R.S. or C.I. brackets painted

white, 32mm C.P. brass waste of standard pattern , C.P

4 MR brass wall flange 32 mm dia. C.P. brass bottle trap and

union 32 mm dia C.P. pipes to wall flange. complete

including cutting and making good the walls wherever

Table top wash basin Each 7 12,000.00 84,000.00

Supply, installation, testing and commissioning of 15mm C.P.

5 MR brass single hole wash basin mixer without popup waste

system with 450mm long copper pipes and brass nut Each 7 6,064.37 42,450.61

Providing & fixing toilet paper holding including cutting and

6 MR making good the walls. 1,561.92

Digitally signed by AMIT

SL. NO. DSR - DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) NS Amount (Rs)

Providing & fixing Horizontal liquid soap dispenser with

7 MR stainless steel lid and brackets fixed to wooden cleats with

C.P. brass screws. Each 7 3,714.79 26,003.51

Providing & fixing C.P. brass coat hooks fixed on toilet door

8 MR with C.P. brass screws 618.70

Providing & fixing beveled edge mirror 5.5mm thick of

superior quality plate glass complete with 6mm thick marine

9 MR ply sheet ground fixed to wooden cleats with CP brass

screws and washerswith 40 mm wide teak wood frame as

per design including polishing

10 MR Providing & fixing Hand Shower (Health Faucet) with 8mm

dia, 1M long PVC tube and wall hook CP brass wall flange Each 7 1,781.81 12,472.69

Providing & fixing, testing and commissioning of storage type

electric water heater with automatic thermostatic control

11 MR electric element, pressure release valve, brackets fixed to

expansion fasteners with M.S. nuts and bolts all complete

including cutting and making good the walls wherever

05 litres capacity (Horizontal /Vertical type1.5 kw electrical

Providing & fixing wall mounted 25 mm dia Stainless steel

12 MR coated grab bar including cutting & making good the

walls(size 450mm long) Each 7 1,041.09 7,287.64

Providing & fixing 15 mm dia C.P. brass bib cock with C.P.

wall flange of approved quality. Each 7 11,051.74

FRAGRANCE DISPENSER MACHINE :-Providing and fixing of

Automatic Fragrance Dispenser machine complete with

refill can and 'C' size battery (2 Nos) for operation fixed to

wooden cleats with CP brass screws Each 7 4,623.87 32,367.06

Providing and fixing of stainless steel finish Paper Towel

15 MR Dispenser having capacity of 300-350 paper towels fixed to

wooden cleats with C.P. brass screws Each 7 5,556.35 38,894.43

Providing and fixing of wall mounted fully automatic hand

16 MR dryer in SS/ black finish as per approval complete will all

accessories. Each 7 5,902.96 41,320.74

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen

sink as per IS:13983 with C.I. brackets and stainless steel plug

16 17.10 40 mm, including painting of fittings and brackets, cutting

and making good the walls wherever required :

17.10.1 Kitchen sink with drain board

Supply, installation, testing and commissioning of 15mm C.P.

brass single hole sink mixer complete. Each 1

Digitally signed by AMIT

SL. NO. DSR - DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) NS Amount (Rs)

Detail of Sanitary fixture are for the information of the

Contractor,however model/makes of all sanitary fixtures

i. shall be selected by Architect/Interior designer/Project

manager and the same shall be binding for execution.

No additional fixing cost shall be paid for change in type of

sanitary fixtures.

Contractor to receive all the above mentioned items &

store at place as directed at site.

TOTAL CARRIED OVER TO SUMMARY 7,514.65 723,084.13

Digitally signed by AMIT

SUB HEAD B: WATER SUPPLY

SL. DSR Rate DSR Amount NS Amount

DSR /NS DESCRIPTION OF ITEMS UNIT Qty NS Rate (Rs.)

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes

having thermal stability for hot & cold water supply including all

(CPVC) plain & brass threaded fittings including fixing the pipe

with clamps at 1.00 m spacing. This including jointing of pipes &

fittings with one step CPVC solvent cement and testing of joints

complete as per direction of engineer in charge. .

Internal Work - Exposed on Wall

18.7.5 40 mm nominal outer dia pipes. Metre 40.00 702.95 28,118.00

18.7.6 50 mm nominal outer dia pipes. Metre 120.00 934.15 112,098.00

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes

having thermal stability for hot & cold water supply including all

CPVC plain & brass threaded fittings i/c fixing the pipe with

2 18.8 clamps at 1.00 m spacing. This including jointing of pipes & fittings

with one step CPVC solvent cement and the cost of cutting

chases and making good the the same including testing of joints

complete as per direction of engineer in charge.

Concealed work including cutting chases and making good the

18.8.2 20 mm nominal outer dia pipes. Metre 320.00 537.60 172,032.00

18.8.3 25 mm nominal dia Pipes Metre 150.00 627.25 94,087.50

18.8.4 32 mm nominal dia Pipes Metre 200.00 739.30 147,860.00

Providing and fixing brass stop cock of approved quality

Providing and fixing gun metal gate valve with C.I. wheel of

approved quality (screwed end):

18.17.1 25 mm nominal bore Each 5.00 622.40 3,112.00

Digitally signed by AMIT

SL. DSR Rate DSR Amount NS Amount

DSR /NS DESCRIPTION OF ITEMS UNIT Qty NS Rate (Rs.)

18.17.2 32 mm nominal bore Each 5.00 689.60 3,448.00

Providing and fixing C.P. bass angle valve for basin mixer and

5 18.53 geyser points of approved quality conforming to I.S:8931 a) 15

mm nominal bore.

Providing and fixing unplasticised P.V.C connection pipe with

PTMT Nuts coller and bush of approved quality and colour.

18.74.2 15mm nominal bore with 45cm length Each 30.00 121.90 3,657.00

Sub-Total of Water Supply Installation, Separate for Scheduled & Non-Scheduled Items 594,099.25

Digitally signed by AMIT

SUB HEAD C: INTERNAL DRAINAGE (SOIL, WASTE & VENT PIPES)

SL. DSR Rate NS Rate DSR Amount NS Amount

DSR /NS DESCRIPTION OF ITEMS UNIT Qty

Providing and fixing cast iron trap of self cleansing design with cast

iron screwed down or hinged grating with or without vent arm

complete, including cost of cutting and making good the walls and

100 mm inlet and 100 mm outlet centrifugally cast (spun) iron S&S as

2 17.35 Providing and fixing soil, waste and vent pipes.

Centrifugally cast (spun) iron S&S pipe as per IS 3989.

17.35.1.2 100mm dia cast (spun) iron S&S pipe Metre 120.00 1,077.40 129,288.00

Centrifugally cast (spun) iron S&S pipe as per IS 3989.

17.35.2.2 75mm dia cast (spun) iron S&S pipe Metre 100.00 1,042.20 104,220.00

Providing and fixing single equal plain junction of reqd. degree with

3 17.43 access door, insertion rubber washer 3mm thick, bolts and nuts 739.30

17.43.1.2 Sand cast (spun) iron pipe IS-3989 Each 20.00 731.40 14,628.00

17.43.2.2 Sand cast (spun) iron pipe IS-3989 Each 10.00 573.80 5,738.00

4 17.44 Providing and fixing single equal plain junction of reqd. degree.

17.44.1.2 Sand cast (spun) iron pipe IS-3989 Each 20.00 689.60 13,792.00

17.44.2.2 Sand cast (spun) iron pipe IS-3989 Each 10.00 498.90 4,989.00

Providing and fixing bend of required degree with access door,

insertion rubber washer 3mm thick, bolts and nuts complete.

17.38.1.2 Sand cast (spun) iron pipe S&S as per IS 3989. Each 20.00 597.60 11,952.00

Digitally signed by AMIT

SL. DSR Rate NS Rate DSR Amount NS Amount

DSR /NS DESCRIPTION OF ITEMS UNIT Qty

17.38.2.2 Sand cast (spun) iron pipe S&S as per IS 3989. Each 10.00 453.40 4,534.00

6 17.39 Providing and fixing bend of required degree .

17.39.1.2 Sand cast (spun) iron pipe S&S as per IS 3989. Each 20.00 439.75 8,795.00

17.39.2.2 Sand cast (spun) iron pipe S&S as per IS 3989. Each 10.00 298.20 2,982.00

7 17.57 Providing and fixing collar.

17.57.1.2 Sand cast (spun) iron pipe S&S IS-3989 Each 20.00 439.75 8,795.00

17.57.2.2 Sand cast (spun) iron pipe S&S IS-3989 Each 10.00 271.45 2,714.50

Providing and fixing MS holder bat clamps of approved design to

cast iron (spun) pipe embedded in and Including cement concrete

8 17.37 blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded

stone aggregate 20mm nominal size) including cost of cutting holes

and making good the walls etc.

Providing and fixing G.I. Pipes complete with G.I. Fittings and clamps.

including cutting and making good the walls etc.

18.10.5 40 mm nominal bore Metre 20.00 725.15 14,503.00

18.10.6 50 mm nominal bore Metre 80.00 893.20 71,456.00

Painting G.I. Pipes and fittings with two coats of anticorrosive

bitumastic paint of approved quality

18.40.4 32 mm nominal bore Metre 120.00 18.40 2,208.00

18.40.5 40 mm nominal bore Metre 20.00 20.95 419.00

18.40.6 50 mm nominal bore Metre 80.00 25.25 2,020.00

Digitally signed by AMIT

SL. DSR Rate NS Rate DSR Amount NS Amount

DSR /NS DESCRIPTION OF ITEMS UNIT Qty

Painting sand cast iron / centrifugally cast iron( spun) iron soil, waste

and vent pipes and fittings with paint of any colour such as

chocolate, grey or buff etc. over a coat of primer (of approval

quality) for new work

17.65.1 100mm dia cast (spun) iron S&S pipe Metre 120.00 69.55 8,346.00

17.65.2 75mm dia cast (spun) iron S&S pipe Metre 100.00 52.90 5,290.00

Providing and fixing G.I. Inlet fitting of suitable size with 2 & 3 Nos. G.I.

13 NS Socket 32 & 40 welded G.I. pipe and dipped in hot bitumen

complete in all respect.

100 mm diameter pipe (Hopper ) Each 20.00 1,150.00 0.00 23,000.00

Providing lead caulked joints to sand cast iron/centrifugally

cast(spun) iron pipes & fittings of diameter :.

Providing & filling the joints with spun yarn,cement slurry & cement

mortar 1:2(1 cement: 2 fine sand) in SCI/CI pipes.

16 17.48 Providing and fixing single unequal plain junction of reqd. degree.

17.48.1.2 Sand cast (spun) iron pipe IS-3989 Each 20.00 798.80 15,976.00

Sub-Total of Drainage Installation, Separate for Scheduled & Non-Scheduled Items 597,435.50 23,000.00

Digitally signed by AMIT

SUB-HEAD - D - SPRINKLER PIPING & ACCESSORIES

SL. NO. DSR/ NS DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) NS Amount (Rs)

Providing, laying, testing & commissioning of 'C' class heavy duty

MS pipe conforming to IS 3589/IS 1239 including Welding, fittings

like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing

the pipe on the wall/ceiling with suitable clamp/support frame

and painting with two or more coats of synthetic enamel paint of

required shade complete as required :

Shifting of existing pipes including testing & commissioning of MS

pipe including Welding, fittings like elbows, tees, flanges, tapers,

nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with

suitable clamp/support frame and painting with two or more coats

of synthetic enamel paint of required shade complete as required

as per directions of engineer-in-charge.

Supplying, fixing, testing and commissioning of butterfly valve of PN

1.6 rating with bronze/ gunmetal seat duly ISI marked complete

with nuts, bolts, washers, gaskets conforming to IS 13095 of

following sizes as required :

Digitally signed by AMIT

SL. NO. DSR/ NS DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) NS Amount (Rs)

Providing and fixing ISI Marked of approved make Fire Extinguishers

complete with all accessories as per manufacturer's specifications.

4.1 CO2 gas nozzle type - 9 Litre capacity (IS:15683). NOS 4.00 13,940.00 55,760.00

4.2 Mechanical Foam gas cartridge type. 9 Kg capacity (IS:15683). NOS 4.00 3,153.00 12,612.00

4.3 ABC dry powder stored pressure type 6 kg capacity (IS:15683). NOS 20.00 2,796.00 55,920.00

Providing, fixing, testing & commissioning of 15mm dia quartzoid

5 NS bulb type sprinklers of rating 68 degree centigrade with required

5.4 21.4 Concealed Sprinkler NOS. 325.00 1,397.00 454,025.00

Supplying, installation, testing & commissioning of sprinkler flexible

pipe (UL Listed) of stainless steel complete with 15 NPT on reducer

thread with maximum working pressure of 175 PSI test pressure of

6 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to

sprinkler head (Outlet) 15mm NPT female thread with reducer,

nipple, 2 side brackets, center bracket, stockbar of following sizes

complete as required.

Providing and fixing signages printed on photoluminescent U1000

aluminium sheet of 1.0 mm (+ -10%) containing lumigen II as base

chemical, covered under UV stablized coating and of appropriate

size including fixing on wall, door, ceiling etc. with proper clamps,

hangers, cleats anchor fasteners etc. complete in all respacts as

diercted by Engineer-in-charge

Providing, jointing and testing of automaticaly operated Halotron

8 NS fire extinguishers(cap-5kg,temperature rating-68degc,test pressure- NOS. 2.00 16,308.00 32,616.00

30bar) complete with all accessories/fittings.

TOTAL CARRIED TO SUMMARY 1,289,635.00 266,808.00

Digitally signed by AMIT

Interior Fit-Out Works in The Office Space of the MSTC at World Trade Centre, Nauroji Nagar, New Delhi

Summary of HVAC Works

S.No. Description of Works Amount (DSR, in Rs.)

Digitally signed by AMIT

Interior Fit-Out Works in The Office Space of the MSTC at World Trade Centre, Nauroji Nagar, New Delhi

DSR -2022 NON- DSR

Sno. Description Units Qty Rate Amount Rate Amount

1 MR Replace AHU canvas connections Nos 2.00 6,160.00 12,320.00

Supply, Installation, Testing Balancing & Commissioning of

G.S.S square/ rectangular ducting complete with gaskets,

elbows, splitters, vanes, supports adjustable dampers, etc. as

2 per drawings and as required for dehumidified air

distribution of following thickness as per approved working

drawings and requirement .

iii 16.12.1.3 Thickness 1.00 mm sheet Sq.m 80.00 1,381.00 110,480.00

Supply and fixing of external thermal insulation on supply air

ducts with 19mm thick chemically cross linked closed cell

polythene (XLPE) fire retardant grade insulation of density

3 16.23.1 not less than 30kg per cum in single layer with factory Sq.m 1,770.00 754.00 1,334,580.00

lamination of 30 micron aluminium foil or 19mm thick

insulation as per CPWD specifications

Suply, installation, testing and commissioning of GI volume

control duct damper complete with neoprene rubber

gaskets,nut,bolts,screws linkages,flanges etc. as per

Supplying, fixing, testing & commissioning of powder coated

extruded aluminium section supply air grills with aluminium

volume control dampers, as per specifications.

Supplying, & fixing, of powder coated extruded aluminium

section return air grills with louvers but without volume

control dampers, complete as per required.

Supplying, fixing, testing commissioning of supply air

7 16.17 diffusers of powder coated aluminium with aluminium Sq.m 20.00 12,184.00 243,680.00

volume control dampers. ( 23Nos of 600x600mm)

Supplying, fixing, testing, commissioning of return air diffusers

of powder coated aluminium.

Digitally signed by AMIT

Interior Fit-Out Works in The Office Space of the MSTC at World Trade Centre, Nauroji Nagar, New Delhi

DSR -2022 NON- DSR

Sno. Description Units Qty Rate Amount Rate Amount

Supplying, fixing Acoustic lining of supply air ducting

complete with G.I frame, tissue paper, 28G perforated al.

Sheet, 25mm thick 32kg/cu.m fibreglass insulation as per

CPWD specifications.

Supplying, fixing , testing and commissioning of fire dampers

in supply air duct/ main branch and return air path as &

where required of required sizes including control wiring. The

damper shall be motorised and spring return so as to close

the damper in the event of power failure automatically and

open the same in case of power being restored .the spring

return action shall be built mechanism and not externally

mounted . The damper shall also be closed in the event of a

fire signals complete as required as per specifications .

b 16.20.2 Motorised Actuator No. 8.00 9,948.00 79,584.00

Supplying, fixing, testing commissioning of Inline Fan of GI

Casing Circular / Rectangular Type with light weight

11 MR dynamic balanced GI Impeller, suitable forSingle Phase

Motor (Without Speed Regulator, Bird Screen and Louver) for

toilet/ dinning / pantry exhaust.

Digitally signed by AMIT

Interior Fit-Out Works in The Office Space of the MSTC at World Trade Centre, Nauroji Nagar, New Delhi

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount NDSR Amount

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant

Flow/ Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and

heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum

two compressors for above 14 HP modules, microprocessor based Controller, top

discharge type condensing unit(s), with R410A Refrigerant, vibration isolators, with

suitable foundation etc. complete as required.The unit shall deliver the rated capacity

at AHRI Conditions and work even at 50°C ambient temperature without tripping.The

unit shall be suitable to work on 400V+/-10%, 3 Phase, 50Hz AC power supply.The unit

shall be filled with first charge of the refrigerant and ready for use as required.The COP

at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .

2.0 INDOOR UNIT

Supply, installation, testing and commissioning of following minimum capacity 4-

wayflow VRV/ VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic

washable media pre-filter, fan section with low noise fan/ dynamically balanced

blower, multi speed motor, coil section with DX Copper coil, electronic expansion

2 valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless

remote control etc., suitable for operation on single phase 230V±10%, 50 HzAC supply,

complete, as required. The unit shall have automatic force shut down provision in case

of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be

at air inl et conditions of 27 Degree CD Band 19 Degree CWB temperature.

4-Way Cassette type

1-Way Cassette type

Supply, installation, testing and commissioning of following minimum capacity VRV/

VRF High wall type Indoor unit equipped with washable synthetic media pre-filter, fan

section with low noise fan/ dynamically balanced blower, multi speed motor, coil

section with DX copper coil, electronic expansion valve, outer cabinet, cordless

3 remote control, drain pan, necessary accessories etc., suitable for operation on

230V±10%, 50Hz, single phase AC supply, complete as required. The unit shall have

automatic force shut down provision in case of fire on receiving signal from BMS

System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree

C DB and 19 Degree C WB temperature.

3.0 REFRIGERANT PIPING

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen

testing of following nominal sizes of soft/hard drawn copper refrigerant piping for

VRV/VRFsystem, complete with fittings, with suitable adjustable ring type hanger

DSR 2019 supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular

VRF/VRV insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of

specified thickness as given below for Suction and Liquid lines, all accessories as per

specifications etc. as required :

3.1 5.1 34.9 mm O.D (wall Thickness-1.2 mm) (Insulation: 19 mm) Rmt 120.00 1,230.00 147,600.00

3.2 5.8 28.6 mm O.D (wall Thickness-1.0 mm) (insulation : 19 mm) Rmt 85.00 1,108.00 94,180.00

Digitally signed by AMIT

Interior Fit-Out Works in The Office Space of the MSTC at World Trade Centre, Nauroji Nagar, New Delhi

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount NDSR Amount

3.3 5.6 22.2 mm O.D (wall Thickness-1.0 mm) (insulation : 19 mm) Rmt 65.00 865.00 56,225.00

3.4 5.5 19.1 mm O.D (wall Thickness-1.0 mm) (insulation : 19 mm) Rmt 70.00 707.00 49,490.00

3.5 5.4 15.9 mm O.D (wall Thickness-1.0 mm) (insulation : 13 mm) Rmt 60.00 588.00 35,280.00

Supplying and installing of following size of perforated hot dip galvanized G.I cable

4 MR tray with perforations not more than 17.5%, in convenient sections, joined with

connectors, suspended from ceiling with G.I suspenders including bolts and nuts, etc.

for carrying refrigerant pipe in outdoor application as required.

4.1 450 mm width x 62.5 mm depth x 2 mm thickness Rmt 20.00 1,128.00 22,560.00

4.2 225mm width x 50 mm depth x 1.6 mm thickness Rmt 90.00 722.00 64,980.00

5 CONDENSATE DRAIN UPVC PIPE

Supply, installation, testing and commissioning of uPVC Pipe ,complete with fittings,

supports,U trap arrangement,Clean Plug with 6mm nitrile insulation and accessories as

per specifications, drawings.

6 MR Imported fittings Y-joints and headers etc. Nos 19.00 4,370.00 83,030.00

7 Control & Trasmission Wiring

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS

1.14 PVC insulated copper conductor, single core cable in surface/ recessed medium class

PVC conduit as required.

8 Timer for Split ac for Server Nos. 2.00 3,867.00 7,734.00

9 Precision air conditioner system (PAC) for server room

Digitally signed by AMIT

Interior Fit-Out Works in The Office Space of the MSTC at World Trade Centre, Nauroji Nagar, New Delhi

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount NDSR Amount

SITC of 3TR wall mounted high performance split type cooling unit suitable for Critical

Technology/Equipment room. Each unit shall facilitate installation in Small Areas, shall

feature robust design to run 24x7, Auto-Restart function, Monitoring with Unit-to-Unit

Communication and Ease of service.

Indoor section & outdoor section.

The Indoor unit shall comprise of Metallic Body construction with insulated side panels,

Evaporator Coil with Hydrophilic Coating, Backward Curve fan with EC motor, HDPE

Washable Filters, Expansion Valve, R407C/R410a Refrigerant, Corded Remote,

Microprocessor Controller, G4 Filter, Suction and Discharge piping, Internal power and

Control wiring, HP/LP Cutouts, Power and Control contactors and Other Electrical &

safety accessories. Outdoor cabinet consists of Compressor, Fan, motor and

Condenser coil. Return air conditions of 27deg.C/40% RH at a condensing temperature

Dimension (H x W x D)[mm]: 1100 x 375 x 515 (Indoor unit)

Team Mode feature for unit control, synchronising the Multiple No. of units to work as

single system for all above units.

Fault Failure changeover, Cascading Effect & Sequencing of above Units

Low-side material and accessories

Hot gas line -Supply & fixing of Interconnecting Copper piping between indoor &

outdoor unit along with support, fitting, paint and accessories. Copper piping will be

duly insulated with in the AC space only.@25mtr per machine

Liquid line -Supply & fixing of Interconnecting Copper piping between indoor &

outdoor unit along with support, fitting, paint and accessories. Copper piping will be

duly insulated with in the AC space only.@25mtr per machine

Supply & fixing of Indoor & Outdoor unit stands duly painted with anti corrosive black

paint, vibration pads, nut & bolts and fixing accessories. @1no. per machine

Initial charge of R-407c refrigerant gas & oil. @12kg per machine

Supply and laying of Interconnecting FRLS copper cabling between indoor & outdoor

unit with fitting and accessories for compressor (5c x 2.5sqmm A) @25mtr per machine

Supply and laying of Interconnecting FRLS copper cabling between indoor & outdoor

unit with fitting and accessories w/o cable tray for control signal (6c x 0.5sqmm

flexible/A) @25mtr per machine

Supply & laying of Incoming FRLS Copper Cabling from Incoming Isolator to CRAC Unit

(5cx6sqmm) @10mtr per machine

Supply & laying of sequential cable of size 2c x0.5sqmm flexible @5mtr per machine

supply and laying of 10c x 1sqmm flexible cable from controller to indoor unit for HP,

LP, A1 , A2, blower fan alarm etc. information @20mtr per machine

Supply & laying of HDPE/PVC Condensate drain piping with insulation in building area

along with fitting and accessories. @10mtr per machine

2 inch GI cable tray for condensor cable and compressor cable @25mtr per machine

Complete 3Tr at 27+/-1 deg.C/40% RH (2working + 1standby) PAC system Job 2 1,332,335.00 2,664,670.00

Digitally signed by AMIT

Interior Fit-Out Works in The Office Space of the MSTC at World Trade Centre, Nauroji Nagar, New Delhi

Summary for E & M Component

Sub Head Descriptions DSR Amounts NDSR Amounts

SH-l EI- Point Wiring, DB, Earthing, Lighting, Cable, Cable Tray, LT Panel 2,854,634.00 6,082,428.74

SH-VI LAN NETWORKING & WI-FI SYSTEM 459,200.00 804,572.00

SH-VlI EPABX SYSTEM 220,050.00 2,185,170.00

Digitally signed by AMIT

Interior Fit-Out Works in The Office Space of the MSTC at World Trade Centre, Nauroji Nagar, New Delhi

Bill of Quantity for E & M Component

Sr. No. DSR 2022 DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

(SH-I: EI WORKS)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm

FRLS PVC insulated copper conductor single core cable in surface / recessed

1 1.10 medium class PVC conduit, with modular switch, modular plate, suitable GI box

and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable etc. as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call

bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated

2 1.55 copper conductor single core cable in surface/ recessed PVC conduit, and

earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single

core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of

3 1.14 FRLS PVC insulated copper conductor, single core cable in surface/ recessed

medium class PVC conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular

4 1.24 plate & switch box including connections but excluding modular plate etc. as

4.5 1.24.7 TV antenna socket outlet Each 15.00 148.00 2,220.00

Supplying and fixing following size/ modules, GI box alongwith modular base &

cover plate for modular switches in recess etc. as required.

Supplying and fixing following Modular base & cover plate on existing modular

metal boxes etc. as required.

Digitally signed by AMIT

Sr. No. DSR 2022 DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supplying and fixing two module stepped type electronic fan regulator on the

7 1.25 existing modular plate switch box including connections but excluding modular Each 2.00 369.00 738.00

plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate &

switch box excluding modular plate as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on

9 1.31 surface or in recess, including providing and fixing 3 pin 5/6 A modular socket Each 10.00 477.00 4,770.00

outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size Gl box with modular plate and cover in front on

10 1.32 surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular Each 13.00 586.00 7,618.00

socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and

earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel

enclosure, on surface or in recess, with chained metal cover for the socket out let

and complete with connections, testing and commissioning etc. as required.

Fabricating, supplying & installation on surface/ recess 2.0 mm thick factory

fabricated GI Sheet raceways height 40 mm and of totally enclosed with 2 mm

thick covered. Two lengths of raceways and junction box shall be joined together

to make it dust proof. Chipping and removing screed to install the raceways in

floor, including removal and disposing of debris / fixing in ceiling along with

suspender and accessories as per instruction of Engineer in charge.

Fabricating, supplying & installation on surface/ recess 2.0 mm thick factory

fabricated GI Sheet raceways height 50 mm and of totally enclosed with 2 mm

thick covered. Two lengths of raceways and junction box shall be joined together

to make it dust proof. Chipping and removing screed to install the junction box

in floor, including removal and disposing of debris / fixing in ceiling along with

suspender and accessories as per instruction of Engineer in charge.

13.1 a 500 mm (wide) x 500 mm (length) X 50 mm (height) Each 20.00 2,360.00 47,200.00

13.2 b 350 mm (wide) x 350 mm (length) X 50 mm (height) Each 20.00 1,990.00 39,800.00

13.3 c 250 mm (wide) x 300 mm (length) X 50 mm (height) Each 15.00 1,580.00 23,700.00

13.4 d 200 mm (wide) x 200 mm (length) X 50 mm (height) Each 15.00 1,360.00 20,400.00

Digitally signed by AMIT

Sr. No. DSR 2022 DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

13.5 e 150 mm (wide) x 150 mm (length) X 50 mm (height) Each 20.00 970.00 19,400.00

13.6 f 100 mm (wide) x 100 mm (length) X 50 mm (height) Each 40.00 780.00 31,200.00

Supplying and fixing of following sizes of steel conduit along with accessories in

14 1.2 surface/recess including painting in case of surface conduit, or cutting the wall

and making good the same in case of recessed conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with

15 1.21 accessories in surface/recess including cutting the wall and making good the

same in case of recessed conduit as required.

Providing and fixing in position the following pvc flexible conduits including all

fixing accessories as required.

16.1 a 20 mm dia flexible conduit with end couplers P/Mtr 125.00 35.00 4,375.00

16.2 b 25 mm dia flexible conduit with end couplers P/Mtr 145.00 45.00 6,525.00

16.3 c 32 mm dia flexible conduit with end couplers P/Mtr 60.00 65.00 3,900.00

Supplying and drawing following sizes of FRLS PVC insulated copper conductor,

17 1.17 single core cable in the existing surface/ recessed steel/ PVC conduit as

Supplying and fixing following way, single pole and neutral, sheet steel, MCB

distribution board, 240 V, on surface/ recess, complete with tinned copper bus

bar, neutral bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole and neutral, sheet

steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned

copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder

painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing of following ways surface/ recess mounting, vertical type,

415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder

painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth

bar, din bar for mounting MCBs (but without MCBs and incomer ) as required .

(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are

Digitally signed by AMIT

Sr. No. DSR 2022 DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supplying and fixing of following ways surface/ recess mounting, vertical type,

415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder

painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth

bar, din bar for mounting 160A, 35ka,MCCBs (but without MCCBs and incomer )

as required . (Note : Vertical type MCCB TPDB is normally used where 3 phase

outlets are required.)

Providing and fixing following rating and breaking capacity and pole

MCCB with thermo magnetic release and terminal spreaders in existing

cubicle panel board including drilling holes in cubicle panel, making

connections, etc. as required.

Supplying and fixing 63 amps rating, 240/415 volts, 10 kA, “C” curve, miniature

23 circuit breaker suitable for inductive load of following poles in the existing MCB

DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature

24 2.10 circuit breaker suitable for inductive load of following poles in the existing MCB

DB complete with connections, testing and commissioning etc. as required.

Supply, installation, testing and commissioning of the following sizes of PVC

trunking system with end caps, bends, elbows complete as required.

Providing and fixing of Gel-Chemical Earthing Electrode of G.I. made as pipe in

pipe technology(IS:3043 : 1987)duly CPRI Approved as per following

Length - (3000 mm)

DIA (outer) - (80 mm)

DIA (Inner) - (40 mm)

26 MR DIA-Terminal Strip Hole - (25 mm) Each 2.00 46,890.00 93,780.00

Space Inside Electrodes - (Filled with Conductive Mixture)

Hot Dip Galvanizing - (70 - 100 Microns)

And earth enhancing compound should be used to treat the soil for lowering the

effective ground impedance 50Kg for each earth pit to make it maintenance

free and to minimize the ground voltage potential rise and pit covered with PVC

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth

27 5.10 electrode including connection with brass nut bolt, spring, washer P/Mtr 25.00 1,551.00 38,775.00

excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth

28 5.11 electrode including connection with G.I. nut, bolt, spring, washer P/Mtr 25.00 706.00 17,650.00

excavation and re- filling etc. as required.

Digitally signed by AMIT

Sr. No. DSR 2022 DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for

connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for

connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing

Supplying & Laying of following sizes copper conductor PVC

insulated PVC unsheathed unarmoured flexible cables confirming to IS:

7098 (Part-I) 1988 of 1.1 KV in existing open masonry

duct/surface/raceways/pipe etc complete as reqd.

Supply, installation, testing and commissioning of copper Earth busbar of size

33 MR 50 X 5 X 400 mm in suitable size MS sheet enclosure made out of 1.6mm Each 2.00 3,502.00 7,004.00

thick MS Sheet duly painted with locking arrangement etc. complete as reqd.

SITC of 2'X2' recessed mounted Luminaire with Maximum 36 Watt with Lumen

output of 3600 lumen. The product should be SMD based and have non integral

isolated driver with 2KV inbuilt surge protection. THD<10%, PF >0.9,Product should

34 MR have life class of 50K burning hour at L70 B50 parameter, Luminiare operating Each 80.00 4,530.00 362,400.00

temp 0 D to 45D. Internal wiring should have teflon coted multi strand wires and

external wire should have PVC coated multistrand wires.

STIC of Recessed High Efficiency Round Led Downlight, Body made of Aluminium

and Opal / prismatic Diffuser with homogeneous light distribution and without

hotspots, System power 15W, 230V with CRI>80, Dia 142X44H mm, Cut out Dia

136mm color temperature 3000K/4000K/5700K, IP20, IK04, operating voltage

range 140-270Vac, operating temperature -10° to 45°C, PF>0.95, THD<10%,

35 MR product efficacy>110lm/W, SDCM<5, L70B50@50000hrs, LED binning as per ANSI Each 220.00 1,580.00 347,600.00

Bin C78.377A, 110° shall be luminaire beam angle, drivers efficiency >86%, internal

surge protection of >2.5kV, LED make - Bridgelux, Seoul, Osram, Cree, The

manufacturer shall provide LM79, LM80, TM21, Photoboilogical safety as per IEC

62471, RoHS complaint, BIS both for fixture and drivers.

SITC of Surface / Wall Mounted LED Batten, Body made of Aluminium and Acrylic

Diffuser 20W, with CRI>80, 1200X30X35 H mm, color temperature 4000K/5700K with

IP20, IK04, operating voltage range 140 - 270Vac,

operating frequency 50Hz, PF>0.95, THD>10%, system efficacy 120lm/W, SDCM<5

Luminaire Make - Arraystorm IP20 , 20W, BT9004SFXXN040N4FS000000

Digitally signed by AMIT

Sr. No. DSR 2022 DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supply, Installation, Testing and Commisioning of Suspended /surface High

Efficiency 18-20W per meter Suspended LED Channel, Body made of Aluminium

and Opal Diffuser with homogeneous light distribution and without hotspots,

System power of 40W, 230V, 2385X52X85H mm, Color Temperature

3000K/4000K/5700K, CRI>80, IP20, IK04, operating voltage range 140-270Vac,

37 MR operating temperature -10° to 45°C, PF>0.95, THD<10%, product Each 15.00 10,939.00 164,085.00

efficacy>110lm/W, SDCM<5, L70B50@50000hrs, LED binning as per ANSI Bin

C78.377A, 110° shall be luminaire beam angle, drivers efficiency >86%, internal

surge protection of >3.5kV, LED make - Bridgelux, Seoul, Osram, Cree, The

manufacturer shall provide LM79, LM80, TM21, Photoboilogical safety as per IEC

62471, RoHS complaint, BIS both for fixture and drivers.

Supply, installation, testing and commissioning of linear profile light matching

38 MR above specification and with Recessed Channel light with Diffuser width of 45mm Rmt 80.00 10,939.00 875,120.00

all complete with all required accessories and fittings.

Providing & Fixing Coverings (Ceiling & Wall) Made out of Polyester Kintted fabric

Coated with polyurethane (PU). The Fibric width 2m,3m,4.1m,&5.1m with Weight

of 200gm/m^2. thickness of 0.3mm. The appearance of fabric is Matl. smooth

and uniform with blance color and ligth transmission of 50%. The tear strength of

fabric should be accordance to CH. 4.5daN; TR: 6.5 daN. The fire Railing should

be accordance to B-S1, do. The febric should be humidity ressistant and free of

cercinogenic subtance (CMR) or volatile organic compounds (VOC's). At

lableing in accordance with the French decree no, 2011- 321, Oeko -Tex

standar100 certified. The fabric should be paintabe/printable with approved

39 MR manufacturer guidelines with 10-year manufacture guarantee. the Installation of sqm 18.00 12,282.00 221,076.00

fabric should be dry installation 7done at room tamperature using CLIPSO PVC,

ASB tension profiles P.CC/P-C10QS/P-C11QS/P-CCB022/P-B1/P-CC1P. There are

several lighting options available including various LED options and fluorescent

lighting. When Positioned properly. LED Lighting modules provide an even light

flow, casting no shadowns or hot spots. coverings are used for a variety of

aluminated applications, including but not limited to walls, ceiling, lightboxs or

wall frames. coverings can enhance your door with a variety of spacial effects

fiber optics or changinglights, or create a statement piece incorporating custom

printing. The cost of electrical cove light fixtures is included in the same.

Supplying , Installation, testing and commissioning of Suspended Fixed LED 15W

Cylindrical Spotlight, Body made of high grade extruded Aluminium, System

Power 15W, 230V, CRI>80, Dia- 70mm X 165 H mm, color temperature

4000K/5700K, Hi- Precision optics with Beam Angle 36° with IP20, IK02, operating

voltage range 140 - 270V AC, operating frequency 50Hz, PF>0.95, THD>10%,

system efficacy 100lm/W, SDCM<3. Luminaire

Digitally signed by AMIT

Sr. No. DSR 2022 DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supplying , Installation, testing and commissioning of Fixed LED 15w Spotlight,

Body made of high grade extruded Aluminium, System Power 15W, 230V, CRI>80,

Dia 95 mm X 90 H mm, Cut Dia 86 mm, color temperature 4000K/5700K, Hi-

Precision optics with Beam Angle 24/ 36° with IP20, IK02, operating voltage range

140 - 270Vac, operating frequency 50Hz, PF>0.95, THD>10%, system efficacy

100lm/W, SDCM<3.

SITC of high power LED Tracklight, Body made of Aluminium and Anodised

Reflector , and driver housed in Plastic enclosure, System Power 20W, 230V,

CRI>80, Dia 60mm X 135Hmm of housing, 140H mm with Driver Box , color

temperature 3000K/4000K/5700K, Hi- Precision optics with Beam angle

24°/38°/48°, system efficacy 100lm/W, SDCM<3. Luminaire Make - Arraystorm

43 MR 1Mtr. Long Single phase 2Wire Track Light , Dimension -1000X35X20mmH Each 28.00 2,502.00 70,056.00

SITC of Dome type suspended LED Architectural pendant Light, Body made of

high- grade aluminium availablein Matt White, Red, Black, Orange & Antique

copper color, with PMMA diffuser for bright & homogeneous light. System power

35W, 230V, CRI>80, Dia 500X334H mm, Color Temperrature- 3000K/4000K/5700K

Providing & Fixing Heavy Duty 4 Blade, 15" Exhuast Fan complete with all

hardware and connectors etc., as per the direction of the engineer In charge

SITC of decorative light fixture as per approval including all fixing acessories as

required. Base rate: Rs. 4000/-

Suppling, installation, testing and commissioning of electrically operated on 220

V, 50 Hz, AC Supply illuminated exit signage conforming to IS- 10322 for the bank

premises ceiling having the following specifications etc. complete as reqd.

(Make:- Prolite Auto Glow, Model No.FASCIA-E)

a. Housing extruded aluminum alloy.

b. Diffuser cum message panel-CAD design prnting on 8 mm crystal acrylic sheet.

c. Battery-lithium ion rechargeable battery.

d. Backup time 180 minutes.

e. Charging type - constant current charger.

f. Recharging cycle - 16 to 24 Hours.

Supply, installation, testing and commissioning of LED flexistrip having minimum

rating 9.6W/mtr, CCT 3000K/4000K, 5 mtr roll with LED Driver lumens not less

than 3800, luminous efficacy not less than 80 Lumens per watt etc. complete as

Supply & Laying of following sizes Aluminum conductor armoured PVC

49 MR insulated PVC sheathed XLPE cable of grade 1.1 KV in the existing open masonry

duct/ surface/ cable tray/ pipe etc complete as reqd.

Supplying and making end termination with brass compression gland and

50 9.1 aluminium lugs for following size of PVC insulated and PVC sheathed/ XLPE

aluminium conductor cable of 1.1 KV grade as required.

Digitally signed by AMIT

Sr. No. DSR 2022 DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supply & Laying of following sizes Copper conductor armoured PVC insulated

51 MR PVC sheathed XLPE cable of grade 1.1 KV in the existing open masonary duct/

surface/ cable tray/ pipe etc complete as reqd.

Supplying and making end termination with brass compression gland and

52 MR Copper lugs for following size of PVC insulated and PVC sheathed / XLPE 0.00

Copper conductor cable of 1.1 KV grade as required.

Hot Dipped Galvanized Iron Cable Tray 0.00

Supplying and installing following size of perforated Hot dipped galvanized iron

cable tray (Galvanized thickness not less than 50 microns) with perforation not

53 MR more than 17.5%, in convenient sections, joined with connectors, suspended

from the ceiling with

G.I. suspenders including bolts & nuts, painting suspenders etc as required.

53.1 450 mm width X 50 mm depth X 2.0 mm thickness P/Mtr. 25.00 1,126.25 28,156.25

53.2 300 mm width X 50 mm depth X 1.6 mm thickness P/Mtr. 80.00 818.55 65,484.00

53.3 150 mm width X 50 mm depth X 1.6 mm thickness P/Mtr. 50.00 608.60 30,430.00

53.4 MAIN PANEL

Supply,installation,testing and commissing of 3phase and neutral 415V 4 wire free

standing floor mounted indoor MV panel made out of 14 SWG sheet after seven

tank process and painting with epoxy powder coating MV electrical panel shall

be dust and vermin proof ,hinged and locable doors.The panel shall consist of

suitable rating TPN bus bar at the rating of 0.8A /SQMM Supported by DMC/SMC

54 insulator and color coded with heat shrinkable sleeves. Metering shall be

provided as specified .The panel shall have short circuiting with standing

capacity of minimum 36KA and consist of the switch gear as mentioned below

.The panel shall got fabricated from manufacturer with CPRI test certificate .The

panel shall be mounted on U channel including supply and fixing of the

same.(including Capacitor banks)

− 630 Amps 4P On Load change over switch. -1No.

− 630 Amps 4P 36KA MCCB. -1No.

− Spreaders-1Set.

− Extended Rotary Operating Mechanism.-1Set

Digitally signed by AMIT

Sr. No. DSR 2022 DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

− Digital V A F Meter with built in Selector Switch, CTs, CT shorting links, R/Y/B LED

indicating lamps and control SP MCBs.

Outgoing Section

− 40 Amps FP MCB_C curve -1Nos.

− 63 Amps FP MCB_C curve -6Nos.

− 100 Amps FP MCCB -2No.

− 200Amps 4P25KA MCCB-1Nos.

− 8 Step Automatic Power Factor Correction Relay (Digital)_1 No

− 63 Amps TP MCB -3Nos.

− 32 Amps TP MCB -4No.

− 10 kVAR capacitor duty Contactor with 220 V AC Coil_3 Nos

− 5 kVAR capacitor duty Contactor with 220 V AC Coil_4 Nos

− ON / OFF LED Indicating Lamps _7Set

− Start / Stop Push Buttons_7Set

− A/M Selector Switch_1 No

− Control S/P MCB (2/4 A)_7 Nos

− Neutral Links_7 Nos

− Control Blocks_7 Nos

- Enclosure, 300A TPN 415V 50Hz Electrolytic grade AL conductor Busbar with 100%

neutal& Non adhesive PVC insulated heat shrinkable sleeves, Internal Wiring, SET 1.00 355,756.00 355,756.00

Terminals, etc.as required._1Set

Supply,installation,testing and commissing of 3phase and neutral 415V 4 wire free

standing floor mounted indoor MV panel made out of 14 SWG sheet after seven

tank process and painting with epoxy powder coating MV electrical panel shall

be dust and vermin proof ,hinged and locable doors.The panel shall consist of

suitable rating TPN bus bar at the rating of 0.8A /SQMM Supported by DMC/SMC

55 insulator and color coded with heat shrinkable sleeves. Metering shall be

provided as specified .The panel shall have short circuiting with standing

capacity of minimum 36KA and consist of the switch gear as mentioned below

.The panel shall got fabricated from manufacturer with CPRI test certificate .The

panel shall be mounted on U channel including supply and fixing of the

same.(including Capacitor banks)

− 200 Amps 4P On Load change over switch. -1No.

− 200 Amps 4P 36KA MCCB. -1No.

− Spreaders-1Set.

− Extended Rotary Operating Mechanism.-1Set

− Digital V A F Meter with built in Selector Switch, CTs, CT shorting links, R/Y/B LED

indicating lamps and control SP MCBs.

Outgoing Section

− 40 Amps FP MCB_C curve -1Nos.

− 63 Amps FP MCB_C curve -6Nos.

− 125 Amps FP MCCB -1No.

− 8 Step Automatic Power Factor Correction Relay (Digital)_1 No

Digitally signed by AMIT

Sr. No. DSR 2022 DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

− 63 Amps TP MCB -3Nos.

− 32 Amps TP MCB -4No.

− 10 kVAR capacitor duty Contactor with 220 V AC Coil_3 Nos

− 5 kVAR capacitor duty Contactor with 220 V AC Coil_4 Nos

− ON / OFF LED Indicating Lamps _7Set

− Start / Stop Push Buttons_7Set

− A/M Selector Switch_1 No

− Control S/P MCB (2/4 A)_7 Nos

− Neutral Links_7 Nos

− Control Blocks_7 Nos

- Enclosure, 300A TPN 415V 50Hz Electrolytic grade AL conductor Busbar with 100%

neutal& Non adhesive PVC insulated heat shrinkable sleeves, Internal Wiring, SET 1.00 225,509.67 225,509.67

Terminals, etc.as required._1Set

56 Supplying the following MCCBs in sheet steel enclosure. For Ups Input & Output

125A 4P MCCB in sheet steel enclosure surface mounted on the wall along with

a) incoming & outgoing Cable Box, suitable for Termination of Aluminium / Copper No. 4.00 15,015.05 60,060.22

Cable. (For Ups Input )

b) UPS Output panel

- 125 A 4P Onload changeover switch in sheet steel enclosure surface mounted on

the wall along with incoming & outgoing Cable Box, suitable for Termination of

Aluminium / Copper Cable.

- Outgoing Section

- 80 Amps FP MCCB -4No.

- 63 Amps DP MCCB -1No.

- 40 Amps DP MCCB -2No.

- Spreaders-3Set.

- Extended Rotary Operating Mechanism.-3Set

Enclosure, 200A TPN 415V 50Hz Electrolytic grade AL conductor Busbar with 100%

neutal& Non adhesive PVC insulated heat shrinkable sleeves, Internal Wiring, SET 2.00 36,063.18 72,126.36

Terminals, etc.as required._1Set

Providing of rubber mat 1 mtr. wide and 12 mm thick to withstand 3.3 KV

dielectric strength as per IS 5424 : 1969

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of

58.0 mild steel, at least 2 mm thick, and vitreous enameled white on both sides, Each 3.00 269.00 807.00

and with inscription in single red colour on front side as required.

Providing First Aid Box as approved by St. John Ambulance Brigade/Indian

Red Cross conforming to IS 2217 : 1963.

Supply & fixing shock treatment chart duly mounted on a wooden

frame with 5 mm thick glass as reqd. (approximate front area 1.20 sq. metre)

(SH-II: FAS & PA )

Digitally signed by AMIT

Sr. No. DSR 2022 DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supplying, installation, testing and commissioning of micro processor based

intelligent addressable main fire alarm panel, central processing unit with the

following loop modules and capable of supporting not less than 240

devices (including detectors) and minimum 120 detectors per loop and

loop length up to 2 km, network communication card, minimum

320 character graphics/ LCD display with touch screen or other keypad

and minimum 4000 events history log in the non volatile memory (EPROM),

power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed

maintenance free batteries with automatic charger. The panel shall have

facility to connect printer to printout log and facility to have seamless

integration with analog/digital voice evacuation system (which is part of the

schedule of work under SH: PA System) and shall be complete with all

accessories. The panel shall be compatible for IBMS system with open protocol

BACnet/ Modbus over IP complete as per specifications.

61.1 17.2.1.2 Two Loop Control Panel Each 1.00 239,225.00 239,225.00

Supply, Installation, Testing and Commissioning of Fabricated 12U Floor mounted

audio rack with Lockable Toughened Glass Door, Powder coated, Castors(4nos),

Fan(4 Nos), Full Tray Unit(5 Nos), PDU 5/15 amp to accommodate all PA controller

and amplifiers equipments complete as required.

Supplying, installation, testing & commissioning of repeater panel with 320

63 17.2.3 character/ Touch screen LCD display with inbuilt reset, acknowledge and Each 1.00 108,688.00 108,688.00

silence switches complete as required.

Supplying, installation, testing & commissioning of intelligent analog

64 17.2.4 addressable photo thermal detector complete with mounting base complete Each 110.00 2,858.00 314,380.00

Supplying, installation, testing & commissioning of heat detector operating at

65 MR 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with Each 2.00 3,871.00 7,742.00

mounting base complete with all connection etc. as required.

Supplying, installation, testing & commissioning of response indicator on

66 17.2.5 surface/recessed MS Box having two LED, metallic cover complete with all Each 50.00 276.00 13,800.00

connections etc as required.

Supplying, installation, testing & commissioning of addressable manual

call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum

strobe complete as required.

Supplying, installation, testing & commissioning of addressable fire control

module complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with

base as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated

71 17.5.2 with annealed copper conductor having XLPE insulation, steel wire armouring & P/Mtr. 450.00 173.00 77,850.00

FRLS outer sheath complete as required.

Supplying, installation, testing & commissioning of fire fighter phone jack

complete as required.

Digitally signed by AMIT

Sr. No. DSR 2022 DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supplying, installation, testing & commissioning of addressable phone

control module complete as required.

Supplying, installation, testing & commissioning of fire fighter telephone

handset complete as required.

Public Address System

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller

with USB, MP3 player (including 6 zone button paging station) with

seamless integration facility with main fire alarm panel for voice evacuation

complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W recess mount

ceiling/wall speakers complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 250

Watt, 25V rms operating at 240 volt AC supply complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6

zone, with microphone assembly complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper

conductor cable in the existing surface / recessed steel conduit of

following pairs, cores and size including connections and

interconnections etc. as required.

77.1 17.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm Each 390.00 54.00 21,060.00

SH-III: (CCTV SYSTEM)

Supply, Installation, Testing & Commissioning of 4MP IR IP H.265 Vandal Proof

Dome camera Smart IR, up to 30M IR distance, Up to 120 dB WDR (Wide

Dynamic Range),3D DNR (Digital Noise Reduction),H.265+, H.265, H.264, MJPEG,

Corridor mode, Triple streams,3-Axis, IP67, IK10 Vandal Resistant, Color: 0.005Lux

(F1.4, AGC ON), 0 Lux with IR, Video Compression H.265+, H.265, H.264, MJPEG,

Behavior Detection Intrusion, Crossing line, Motion detection, Object left, Missing

object, Intelligent Identification Face detection, Defocus, Scene Change ,PoE

(IEEE802.3 af) Power consumption: Max 7.2W,Edge Storage Micro SD Card, Up to

256GB, ANR Support, Working Environment -40°C ~ +60°C, Humidity ≤ 90% RH(Non-

condensing),Compatible Integration ONVIF (Profile S/G), API.

Supply, Installation, Testing and Commissioning of 32Ch Embedded Network

78.2 Video Recorder with 4 Sata Supports 1 × RJ45 1000M ,4K Cameras, HDMI, VGA, Each 1.00 95,000.00 95,000.00

RAID, Redundant power supply, Smart Analytics and ONVIF

SITC of SSD Hard Disk Drive 8TB, 24/7 surveillance category Only complete etc. as

required. etc. all complete.

Digitally signed by AMIT

Sr. No. DSR 2022 DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supply, installation, testing and commissioning of Video Management software

enabling security related personnel to easily and remotely gather video

evidence, monitor live situations, and configure and maintain a video

surveillance system over Ethernet consisting of digital video recorders (DVRs),

78.4 hybrid digital video recorders, network video recorders (NVRs), analogue video Each 1.00 24,996.00 24,996.00

cameras, and IP video cameras should support Detachable Viewers –users have

the ability to detach Viewer panels and move them to other (or the same)

monitor(s). A maximum of two (2) Viewers can be detached for a total of 75-up

video tiles [two (2) detached and one (1) core Viewer.

Supply, Installation, Testing & Commissioning of 42" Flat Screen HD led (24X7) with

Interfaces include HDMI, DVI, D-sub, Component and Composite input as well as

RS-232C and RJ45 for extensive connectivity, remote control and wall mount unit

/ floor stand complete with making connections etc. complete as reqd.

Supply, Installation, Testing & CommissioningC of HDMI cables 10 meters M2M

etc. all complete.

Supply, Installation ,Testing and Commissioning of 24U (600mm (W)/1000 mm

(D)) floor mount rack with 4 nos. unidirectional wheels, steel sheet

enclosure with glassed front door, perforated powder coated rear door

side panels with top cover, 2x ventilations fans , cable entry at cut outs and

gland plates, 1 cable managers, stationary shelf, 2 nos vertical mounted

powers strip each with 3 Nos 6A power socket with 32 A SP MCB and indicator

of ON and all necessary hardware accessories complete etc. as

with all necessary accessories etc as reqd.

Supply, installation, testing and commissioning of 6 Core Single mode Optical

Fiber Cable in water block loose to taped corruagated steel tape armoured

78.8 polythene outer sealed embedded wih two steel wire on the periphery. The P/Mtr. 25.00 167.00 4,175.00

cables are with UV Stabilized PE Jacket and protected from Rodent attacks

i/c connection etc. complete as reqd.

Supply, installation, testing and commissioning of 12 Port wall/rack mounted LIU

78.9 fully Loaded complete with Adopter Pigtails and othr accessories etc. Each 1.00 33,403.00 33,403.00

Complete as reqd.

Supplying and fixing of following sizes of medium class PVC conduit

77.10 1.21 along with accessories in surface/recess including cutting the wall and

making good the same in case of recessed conduit as required

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing

surface/ recessed Steel/ PVC conduit as required.

Total of SH-III:- 52,000.00 826,859.00

SH-IV UPS SYSTEM

50 kVA UPS with 15 minute backup

Digitally signed by AMIT

Sr. No. DSR 2022 DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supply, unloading, shifting, installation, testing & commissioning of micro

processor controlled 50 kVA transformerless UPS , IGBT based rectifier to achieve

input THDI < 5% and input power factor of greater than 0.99 at 100% loading. True

Online Double Conversion (VFI as per IEC 62040-3) UPS using PWM IGBT

technology , 3 Phase input and 3 phase 415 V output UPS system; and comprising

of the following complete as required and as per specification:

Fully rated Rectifier cum charger unit and 100% rated Invertor unit Integrated in

Fully rated Inbuilt static switch at the inverter output and 100% rated Inbuilt static

switch at the static bypass line integrated in UPS module.

Web-enabled Monitoring and Management through SNMP protocols for multi-OS

environments with below features.

Giving notifications like e-mail, paging notification, broadcast notification,

battery replacement notification, run event-based scripts.

Event logging, data logging and action logging (with date, time, description of

fault and event).

Fully rated Inbuilt Maintenance Bypass Switch for the continuos operation of the

load during maintanance.

Local notification through audible alarm.

Fully rated Battery Circuit Breaker with under voltage coil & deep discharge

protection to the batteries.

Battery Banks comprising of Valve Regulated Lead Acid Sealed Maintenance

Free batteries of minimum 5years design life to provide 15 minutes backup at

50kVA ,0.9PF and ECV=1.7V with each UPS. The batteries shall be installed on

shelves of rack for quick replacement and servicing. The temperature sensor shall

be provided in the battery section for temperature compensated charging. The

bank of batteries shall comprise of required numbers of batteries connected in

Vendor to provide complete details of make of Batteries, ampere hour ratings,

no. of Batteries, Expected life, Final discharge voltage, Nominal float voltage,

Battery recharge time & configuration of back up time, Battery sizing Calculations

Supply, unloading, installation, testing & commissioning of open type MS racks

including top fully cover to protect from falling object to house SMF batteries for

60 kVA UPS system along with suitable interconnecting links, moulded case circuit

breaker having Ithermal, Imagnetic & automatic U/V trip mechanics for Battery

Banks etc. complete as required & as per specifications.

Supply, laying, testing & commissioning of flexible single core copper cable for

interconnections between UPS to UPS, UPS to batteries, complete as required for

Digitally signed by AMIT

Sr. No. DSR 2022 DESCRIPTION OF ITEM UNIT QTY. DSR RATE NDSR RATE DSR AMOUNT NDSR AMOUNT

Supply, Installation, Testing and Commissioning of 5KVA True Online double

conversion VFI technology, High Frequency PWM using IGBT technology, 1 phase

AC Input & 1phase AC Output UPS. Input range should be 180 VAC-260 VAC.

Provisions for maintenance by pass switch module. Microprocessor based LCD

display & indication for various electrical parameters. LED indication with alarm

80 for major fault.

Supply, Installation, Testing and Commissioning of 12V Monoblock suitable size

and nos of sealed maintenance free batteries supporting for 5KVA UPS System

for providing 90 minutes back up time with each UPS at full load with

interconnecting leads, mounting racks/stands for stacking the

batteries, along with Battery Circuit Breaker, Connection, Interconnections, and