TENDER FOR ITEM RATE CONTRACT FOR SPECIAL REPAIR/ REPLACEMENT OF STREET LIGHT WITH LED ON EXISTING POLES ALONGWITH BOUNDARY WALL AT 581 SUB GP DABATHWA UNDER GE(U) MEERUT CANTT.

Amount

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundations etc. or for shafts, well cess pits, manholes,pier holes, laying of pipe and cables etc. but not exceeding 10 sqm on plan including dressing/trimming sides and levelling/grading & ramming bottom of excavation and getting out in soft/loose soil complete all as specified.

Returning ,filling in , including spreading , levelling , watering and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified.

Removing excavated material ( soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified.

M&L fly ash old size bricks, straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection all as specified.

Material and labour for river sand, unwashed and screened dry ) for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete as specified and directed . (Note:Punned thickness shall be measured for the purpose of payment)

Dismantling / taking down street light fittings including brackets necessary electrical connections single/ double of any wattage or size and removing complete all as specified.

Supplying, installing, commissioing and testing of factory made ,CPRI approved ,LT switchgear panel board of size 1000mmx1000mmx400mm (min) , IP-54 (outdoor type) , 415 Volts, 50 Hz, AC supply, three phase and neutral ( 4 wire) , 200 Amps aluminium bus bars duly insulated with heat shrinkable sleeves as per colour code supported on epoxy insulators , having independent compartment for insulated bus bar, incoming feeder and each out going feeder i.e cubical type, made out of 3.15mm thick CRCA sheet , rigid mild steel angle iron frame of 50mmx50mmx6mm with 600mm long extended legs grouting in PCC 1:3:6 type C2 block of size 300mmX200mmx300mm, duly epoxy powder coated internally and externally with approved shade, rubber gasketted, hinged front and back openable doors with proper locking arrangements for dust and vermin proof ,complete including suitable size cable alley, lugs , cable glands,common earth bus bar of GI strip 32x6mm at bottom and making connections with MCCB spreaders,/ wiring with suitable size SC PVC insulated copper conductor cable, locking arrangements 65mm size and lock with keys, earthwork and excavation comprising of the followings and specified hereafter:-

Incoming:-

FP, MCCB, Adjustable thermal 80%-100% and Adjustable magnetic setting Ics= 75% Icu, 25 KA, 100 Amps, 415V , -01 No.(incoming)

Aluminium busbars suitable for 200 Amps, 3 Phase, 4 wire system, not less than 600mm longfixed on insulators -04 Nos

LED type indication lamps ( R-Y-B) with holder panel mounting type complete all as specified. -01 No.

Outgoing:-

FP, MCCB, Adjustable thermal 70%-100% and fixed magnetic setting Ics= 75% Icu, 25 KA, 63 Amps, 415V , -03 Nos.

MCB, FP, 32Amps, 415V, 25 kA, -01 No

S&F 3 core , stranded copper conductor cable 2.5 sqmm, PVC insulated and PVC sheathed , 1100 Volts grade for making connections to street light fittings encased in and including 25 mm dia medium grade PVC conduit and conduit fittings (ISI-marked) fixed with suitable mild steel clamps made to shape out of FI 25x3mm, bolts, nuts and washers @ 1m c/c and duly painted with two coats of stnthetic enamel paint over a coat of rex oxide primer complete all as specified and directed.

S&F Street light GI pipe bracket made out of 25 mm dia nominal bore GI pipe light grade, 1.5M long bend to shape 120 degree angle with suitable adaptor and fixed to poles/wall/ceiling by two Nos MS clamps made out of FI size 40mmx4mm with nuts, bolts and washers duly painted with two coats of synthetic enamel paint over a coat of primer complete all as specified and directed by EIC complete

Disconnecting and taking out / taking down existing burnt out LT under ground XLPE /PVC insulated under ground cable from trenches/ poles/ walls etc of any size from various locations as directed by Engineer-in-Charge.

Supplying, laying or fixing, jointing and testing LT under ground electric power cable Crossed linked polyethylene ( XLPE Cable) insulated, galvanised steel strip or wire armoured, ISI-7098 marked, with aluminium conductor multi stranded , heavy duty 1100 Volts grade of 16 sqmm 2 core ,complete all as specified laid in trenches/ laid under floor or fixed naked with walls / on poles/ in ducts /in GI pipes etc.( Excavation, earth work, sand cushioning, protection bricks/ tiles/ block,clamps, nuts , bolts, washers and pipe shall be measured and paid separately under appropriate items ).

Supplying, laying or fixing, jointing and testing LT under ground electric power cable Crossed linked polyethylene ( XLPE Cable) insulated, galvanised steel strip or wire armoured, ISI-7098 marked, with aluminium conductor multi stranded , heavy duty 1100 Volts grade of 16 sqmm 4 core ,complete all as specified laid in trenches/ laid under floor or fixed naked with walls / on poles/ in ducts /in GI pipes etc.( Excavation, earth work, sand cushioning, protection bricks/ tiles/ block,clamps, nuts , bolts, washers and pipe shall be measured and paid separately under appropriate items ).

S&F Energy saving & environment freindly Light Emitting Diode (LED) street light fitting made out of pressure die cast anodised aluminium with polycarbonate or flat glass optical cover with Penut lens , 45 watts to achieve B1 class road illumination as per IS:1944 and as per national Lighting Code using each LED >1 watt and <3 watt , LED chip efficiency >=135 Lumens/Watt, CRI>70, CCT 5000K to 6500K with LED life at 70% of ligyt put > 50000 hours with isuitable driver140V to 270V universal type with built in surge protection >5KW, 50 Hz + 3%, pf 0.95, Thd <10% eith system efficiency >85 lumens /watt and p[ower efficiency >=90% and overall IP65 or better , driver and luminaire shall comply LM-79/IS:16106 including connecting and testing complete all as specified.

S&F Energy saving & environment friendly LED street light fitting made out of pressure die cast anodised aluminium housing with polycarbonate or flat glass optical cover with Penut lens,70/72 watts Watt to achieve B1 class road illumination as per IS: 1944 and as per national lighting code using each LED >1 watt and <3 watt , LED chip efficiency >= 135 Lumens/Watt, CRI>70, CCT 5000K to 6500K with LED life span at 70% of light output >50000 hours with suitable driver 140V to 270V universal type, with bult in surge protection >5KV, 50 Hz +/- 3% , pf 0.95, THD <10% with system efficiency >85 lumens/ Watt and power efficiency >=90% and overall IP 65 or better , driver and luminaire shall comply LM-79&80/IS:16105 & 16106 and making connections complete all as specified and directed.

S&F pole mounting type junction box factory made of size 250x200x100mm of CRCA sheet duly powder coated with front openable hinged door , locking arrangements, with 2 Nos aluminium bus bars 40 Amps rating mounted on porcelain insulator, cable glands and lugs consisting DIN type rails for fixing MCB SP 6 Amps, 10 kA, -01 no. including mild steel flat iron clamp made out of 25x3mm FI, nuts, bolts and washers duly painted with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.(MCB shall not be measured and paid separately)

D S Enterprises

Shikha Enterprises

Jain Traders

SIDDHARTH TRADERS

BASANT RAM AND SONS