MLAFUND 2024-25 Reethapuram TP

Amount

Earth work excavation for foundation and depositing on bank with in the initial lead of 10m and a lift of 2m in hard stiff clay, stiff block cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders etc complete complying with SS20B. TNDSS No:23&24

Cement concrete of mix 1:4:8 (one part of cement four part of sand and eight part of aggregates) using 40 mm gauge machine broken granite stone jelly for foundation including de watering if found necessary and laid in layers of not more than 15 cm thick well rammed and consolidated etc complying with standard specification. TNDSS No:28

Supplying, fabricating and placing in position of Steel Reinforcement using Mild steel or ribbed tar steel rods, for all RCC works as per the design given by the departmental officers including cost of steel cutting, bending, placing in position and binding with binding wire and all labour charges for cutting, bending, tying and placing in position etc, complete. TNDSS No:97

Supplying and erecting centering to sides and soffits including supports and strutting with necessary centering for soffits upto 3 meter height using mild steel sheet of size 90 cm x 60 cm x 10 mm gauge with MS angles of size 25mm x 25mm x 3mm laid over silver oak (CW) joists of size 10cm x 6cm spaced upto 90cm c/c and casurina props or 10 cm to 13 cm dia spaced at 0.750 cm c/c complying with standard specifications as per TNDSS NO : 30 & 86.

Supplying and erecting centering to sides and soffits including supports and strutting with necessary centering for soffits upto 3 meter height using mild steel sheet of size 90 cm x 60 cm x 10 mm gauge with MS angles of size 25mm x 25mm x 3mm laid over silver oak (CW) joists of size 10cm x 6cm spaced upto 90cm c/c and casurina props or 10 cm to 13 cm dia spaced at 0.750 cm c/c complying with standard specifications as per TNDSS NO : 30 & 86. (for column)

Supplying and erecting centering for sides and soffits including supports and strutting up to 3.29 m height for plain surfaces such as RCC slabs rectangular beams Tee or L beams lintels, stair case beam etc. in all floors with all cross bracing using mild steel sheets of size 90x60 cm and BG10 gauge stiffended with welded mild steel angles of size 25x25x3 mm for boarding laid over silver oak country wood joists of size 10x6.5 cm spaced at about 90 cm center to center and supported with casurina props of 10 cm to 13 cm Ø spaced at 75 cm center to center etc. complete complying with standard specification in all floors. TNDSS No:30&36

Reinforcement Cement concrete 1:1½:3 (one part of cement one and a half part of sand and three part of aggregates) using machine broken granite jelly of 20 mm size for all reinforced cement concrete works excluding cost of centering shuttering strutting and also cost of reinforcement grill in position but including laying vibrating with mechanical vibrators using finishing etc complete, as directed by the departmental officers etc complete complying with standard specification. TNDSS No:30

Brick work in cement mortar 1:5 (one part of cement five part of sand) using country bricks of size 8¾"x4¼"x2¾" including curing, cost and conveyance of all materials to site and all labour charges etc complete as per standard specification.

Supplying fabricating and fixing in position of Alumi, Anod natural colour matt finish sliding window in three track in all floors with standard sizes. All the three shutters with sliding arrangements the bottom section should have gutter arrangements so to drain the water entering and made with extruded aluminium section for outer frames as shown below with necessary accessories such rubber beading. Necessary dismantling making necessary holes in RCC columns, beams or masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by the departmental officers. The Aluminium surfaces should be anodised with matt finish under electrically condition in accordance with IS specification 1868/1962 of Anodic thickness of not less than 15 microns (fifteen) for all sections. All the materials should be got approved by the Engineer incharge before fixing as directed.

Supplying and fixing of steel door with suitable design including cost of materials, welding and conveyance of all materials to site locking arrangements and painting one coat of primer etc. complete as per standard specifications including fixing charges etc. complete for the work.

Supplying and fixing M.S Grill to special windows using MS flats and rounds as directed by the departmental officers inclusive of cost of MS grill including one of red oxide and fixing in position etc complete.

Ceiling plastering and finishing all RCC exposed surface such as RCC slabs, sunshade canopies, stair case steps, landing slab, etc. with cement mortar 1:3 (one part of cement three part of sand) 10 mm thick including packing the surface and provided necessary cement mortar nosing, headings as per the size specification wherever necessary using the same mix as directed by the departmental officers etc. complete complying with standard specification.

Plastering in cement mortar 1:4 mix (one part of cement and four part of sand) 12 mm thick finishing including cost and conveyance of all materials and labour charges for curing and all other incidental charges etc., complete complying with standard specification.

Paving floor with vitrified tiles (marbonite) in all floors over the base layer of cement mortar 1:3 (one par of cement three part of sand) 20 mm thick pointed with white cement at 0/40 kg/m2 including finishing the joints etc complete, as directed by the departmental officers.

Painting two coats with ready mixed plastic emulsion paints of first class quality and of approved colour over a priming coat including through scraping clean removal of dirt etc, complete and including cost of necessary plaster of paris, putty, brushes, wherever required and all labour charges, scaffolding charges etc., complete as per standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc complete complying with standard specification. (The make, quality and colour of paint should be got approved by the departmental officers before use on works.)

Wiring with 2 x 1.5 sq.mm (22/0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box in flush with wall with 5A F.T. switch, covered with hylum sheet of 3mm thick with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC light point / fan point for electronic regulator. (Assume 4 points/ coil) (SD-19)

Wiring with 2 x 1.5 Sq.mm (22/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 mm x 100 mm x 113mm TW switch box in flush with wall with 3 mm thick hylem sheet cover for 5 A 3 pin non interlocking FT wall socket and 5A FT switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC plug point. (SD-37)

Supply and fixing of 16 Amps TPN Switch with metal clad of 500 V with fuse and neutral (Side Handle) on suitable TW board with PWD Earthing SD 146.

Supply and run of 2 of 6 Sq.mm (84/0.3) PVC insulated SC unsheathed copper conductor of 1100V grade on 7/20 GI bearer wire for service connection mains SD 66.

Supply and fixing of single box type 4feet 40 W flu fitting complete with copper choke and condensor with conduit pipe suspension from the ceiling with PVC unsheathed copper leads from terminals to the fitting with flu tube SD 89.

Supply and fixing of 1200 mm (48inch) sweep AC ceiling fan complete with stepped electronic 300W regulator with 1 metre down rod with fan clamp with side plates and cross arm of size 450 mm (18inch) SD106.

WORKS CONTRACT S FRANCIS (BID ID -1179243)