MLALAD Works in NCT of Delhi (8443-Deposit Works)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size).

Supply of earth, carted by mechanical transport including royality, loading, unloading and banking excavated earth in layers not exceeding 20 cm in depth breaking clods, rolling each layer with 1/2 tonne roller or wooden or steel rammers and dressing up in embankment for road, flood banks, marginal banks and guide banks or filling up ground drpression with 5 Km. lead and all lift complete. (earth measured in stacks will be reduced by 20% for payment).

Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in- charge (payment for providing grooves shall be made separately).

Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge :20 mm wide and 15 mm deep groove

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and Assembling precast reinforced cement concrete bench (KK or equivalent make) of over all size 1500 mm x 450 mm , the bench consist of 02 Nos. L-Shape base sport in cement, thickness 100 mm back height 1000 mm front height 450 mm base width 620 mm as per sketch and 05 Nos. reinforced concrete planks in red colour of sized 1500 mm x 100 mm x 50 mm and 01 Nos. RCC planks of size 1500 mm x 200 mm x 50 mm by using M-30 grade of concrete using vibro compaction process, so as to make surface glossy and water proof including transportation, erection all part are jointed to gather with galvanized nuts and bolts of suitable size. All bolts are sealed after assembly.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size).

Providing and fixing of make FOREARM TWIRL/TAI CHI SPINNERS make ARIHANT/KOMPAN/LANDSCAPE/KOOCHIE (HUGO) or equivalent as approved by engineer-in-charge. FOREARM TWIRL/TAI CHI SPINNERS of size 1150x1150x1650mm fabricated with main post of 114mm and 2.5mm thick pipes make of hot roller tubular steel and hot dipped galvnized and powder welded coated using Akzo Noblel or equivalent of 80-120mm micron thick. the circular spinners made from 32mm dia hot dipped galvanized steel rods and welded on to the post using 6mm dia hot dipped galvanized steel suports. All joints of pipe are robotic welded with joints scalloped as necessary and dressed of removing sharp edges and burrs. Zinc primer paint are applied at all welding point prior to finishing. Pedals shall be made of Nylon Alloy with rounded edges to prevent any impact of injury Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by engineer-in-charge. Equipment to be fitted with inbuilt limiter to prevent unwanted movement. on groun with concrete of minimum strength M-25 and J shaped The equipment to be fixed on ground with concrete of minimum strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent onto it and cover nuts and bolts with the base plaste cover.

Providing and fixing of make CHEST PRESS/SEATED CHEST PRESS make ARIHANT/KOMPAN/LANDSCAPE/KOOCHIE (HUGO) or equivalent as approved by engineer-in-charge. CHEST PRESS/SEATED CHEST PRESS of size 1957x733x2058mm fabricated with main post of 114mm and 2.5mm thick pipes made of hot roller tubular stell and hot dipped galvnized and powder welded coated using Akzo Noblel or equivalent of 80-120mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed of removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Seat and base plate cover to be made from virgin LLDPE manufactured by rotational moulding with minumum thickness of 8mm, colourful and UV resistant and environmental friendly. Handgrip to be made from high quality rubber. Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by engineer-in-charge. Equipment to be fitted with inbuilt limited to prevent unwanted movement. All open ends of pipes to be closed by LLDPE caps for user friendly. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover.

Providing and fixing of SHOULDER TWIRL/BIG SHOULDER WHEEL make ARIHANT/KOMPAN/LANDSCAPE/KOOCHIE (HUGO) or equivalent as approved by Engineer-in-charge. SHOULDER TWIRL/BIG SHOULDER WHEEL of size 857x850x1815mm fabricated with main post of 114mm and 2.5mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed of removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. All open ends of pipe to be closed by LLDPE caps for user friendly. The equipment to be fixed on ground with cocnrete of minimum strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover.

Providing and fixing of ABS BOARD/HD SIT UP STATION make ARIHANT/KOMPAN/LANDSCAPE/KOOCHIE (HUGO) or equivalent as approved by Engineer-in-Charge. HD sit up station of size 1400x1366x650mm fabricated with main post of 114mm and 2.5mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-100 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed of removing sharp edges and burr. Zinc primer paint are applied at all weldeing points prior to finishing. Sit up boards and base plate cover to be made from virgin LLDPE manufactured by rotational moulding with minumum thickness of 8mm, colourful and UV resistant and environmental friendly. All open ends of pipe to be closed by LLPDE caps for user frinedly. The equipment to be fixed on groun with concrete fo minimum strength M-25 and J shaped welded bolt and ones the concrete us set, fix the equipment on to it and cover nuts and bots with technical specifications.

Providing and fixing of SHOULDER EXCIER/PULL DOWN CHALLENGER make ARIHANT/KOMPAN/LANDSCAPE/KOOCHIE (HUGO) or equivalent as approved by Engineer-in-Charge. PULL DOWN CHALLENGER of size 2572x805x2187mm fabricated with main post of 114mm and 2.5mm thick made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micron thick.All joints of pipe are robotic welded with joints scalloped as necessary and dressed of removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Pedals shall be made of nylon alloy with rounded edges to prevent any impact of injury. Seat and plate cover to be made from virgin LLPDE manufactured by rotational with minimum thickness of plastic of 8mm colourful and UV resistant and environmental friendly. Bearing used shall be made maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by engineer-in-charge. Equipment to be fitted inbuilt limiter to prevent unwanted movement. All open ends of pipe to be closed by LLDPE caps for user friendly. The equipment ot be fixed on ground with concrete of minimum strength M-25 and J shaped welded bolt and ones the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover.

Providing and fixing of LEG EXTENSION/LEG STRETCH make ARIHANT/KOMPAN/LANDSCAPE/KOOCHIE (HUGO) or equivalent as approved by Engineer-in-Charge. LEG STRETCH of size 932x811x1163mm fabricated with main post of 114mm and 2.5mm thick and rails made from 32mm dia pipes and thickness of 2.4mm pies pipes made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nodal or equivalent of 80-120mm micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed of removing sharp edges and burrs. Zinc primer paint are applied at all welding points prior to finishing. Base plate plastic of 8mm, colorful and UV resistant and environmental friendly. All open ends of pipes to be closed by LLDPE caps for user friendly. The equipment to be fixed on ground with concrete of minimum strenght M-25 and J shaped welded bolt and ones the concrete is set, fix the equivalent on to it and cover nuts and bolts with the base plate cover.

Providing and fixing rubber tile flooring 25mm thick made of SBR (Styrene Butadiene Rubber) with interlocking arrangement and adhesive all complete and size as approved by the Engineer-in-charge.

S S Builders

Laxman Singh

NAHARIA CONSTRUCTION CO.

ANIL KUMAR

moni traders